KJB TMT2WM User Manual
Reset
or
LAN1 L AN2 L AN3 LA N4 WAN
Router
TMT2 Temperature Body
Scanner Camera
User manual
Note
1. Device working temperature: 10 -40 ℃. Do not Install under the vent
And ensure that there is no heating source within 3 meters;
2. People entering the room from a cold outdoor environment will affect
measurement accuracy. The forehead temperature test needs to be
performed indoors without covering the forehead for three minutes and
the temperature is stable;
3. The temperature read by the temperature measuring device is the
temperature in the forehead area. When there is water, sweat, oil or
thick makeup on the forehead. or the elderly have wrinkles, the read
temperature will be lower than the actual temperature. Make sure there
is no hair or clothing covering this area.
-1-
1 Product Overview
1.1 Introduction
The face recognition terminals are suitable for hotels, office buildings,
schools, shopping centers, KTV, bars, buses and communities.
1.2 Product Features
(1) Non-contact automatic temperature detection and voice prompts;
(2) Temperature measurement range: 30-45 ℃,
7-
inch forehead temperature measurement accuracy is ± 0.3℃,
The measurement distance 0.4~1meter;
(3) Auto identify people without masks and sound real-time warning;
(4) Dual sensor with live detection
(5) Face library 22400 person, storage 100,000 recognize record;
(6) Supports SDK and HTTP protocols under Windows / Linux;
(7) Device vision dynamics ≥80dB, suitable for backlight environment;
(8) Supports fog, 3D noise reduction, strong light suppression,
electronic image stabilization, multiple white balance modes.
(9) Linux system
1.3 Packing list
Packing list of 7-inch turnstile
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. 1*Waterproof head for Network cable port and power port
4. 6* Tie 5. 1*Hex screwdriver
6. 1*User manual
Packing list of 7-inch wall-mounted
1. 1*Face recognition terminal 2. 1*Power supply 12V 3A
3. Waterproof head for Network cable port and power port
4. 1*Wall mount bracket 5. 1*Screw fixing plate
6. Mounting plate on the face recognition terminal
7. 1*Hex screwdriver 8. 4*Rubber plug and 8*screws
9. 1*User manual
-2-
wall mounted
No.
Name
Description
J1
WG Out
1:D0 2:D1 3:GND
J2
WG IN
NC
J3
Alarm Out
Connect Magnetic lock or electric lock
J4
USB
Connect the ID identifier or other USB devices
J5
RJ45
Network cable port
J6
DC12V
Connect to 12V / 3A power supply
No.
Description
J1
WG Out：Orange D0、White D1、Green GND
WG IN：Brown and white D0、Yellow D1、Gray GND
Alarm out：Brown Alarm+、Purple Alarm
Connect Magnetic lock or electric lock
RS485：Orange and White 485+、Blue and White 485
USB：Red 5V、Blue D-、Green and white D+、Black GND
J2
Network cable port
J3
Connect to 12V / 3A power supply
2 Specification
1. 7-inch turnstile TMT2
2. 7-inch wall-mounted
TMTWM
3 Wiring Function
-3-
7-inch turnstile 8-inch turnstile
8-inch
7-inch
Wall mounted
-4-
50cm
Mounting plate on the
face recognition terminal
Screw fixing plate
placed in the middle
Wall mount bracket
7-inch
8-inch
7-inch
8-inch
7-inch
8-inch
4 Installation
4.1 Installed on the gate
According to the device of the installation site, in the space position on
the gate or on the front side, the opening diameter of the 7-inch
turnstile larger than 27mm, and the opening diameter of the 8-inch
turnstile larger than 33mm.
Single channel gate Two channel gate
4.3 Mounted on the bracket
Temperature Display
detecting position
Comparison results
Wrist detection
temperature location
4.2 Adjust to best angle and detection position of the detector.
After the temperature measurement access control is fully activated,
the human face is directly facing the device. Observe the face image
on the device screen.
Make sure that the bare skin on the forehead is placed in the "temperatrue measurement area" (best temperature detector distance 0.5m).
-5-
1.1~1.8meters Desktop 0.6meter
4.4 Wall mounted
Part for wall mount:
-6-
1.1meter
Loading...