THANK YOU for purchasing this high-quality product. Register your range at www.kitchenaid.com. In Canada, register your range
at www.kitchenaid.ca.
For future reference, please make a note of your product model and serial numbers. These can be found on the label located on the oven
frame behind the top-right side of the oven door.
Model Number______________________________________________ Serial Number_______________________________________________
Para una versión de estas instrucciones en español, visite www.kitchenaid.com.
Deberá tener a mano el número de modelo y de serie, que están ubicados en el marco del horno, detrás del lado derecho superior
de la puerta del horno.
Table of Contents
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................3
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
2
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without having
the anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock, injury to
persons, or damage when using the range, follow basic
precautions, including the following:
■ WARNING: TO REDUCE THE RISK OF TIPPING OF THE
RANGE, THE RANGE MUST BE SECURED BY PROPERLY
INSTALLED ANTI-TIP DEVICES. TO CHECK IF THE DEVICES
ARE INSTALLED PROPERLY, SLIDE RANGE FORWARD,
LOOK FOR ANTI-TIP BRACKET SECURELY ATTACHED TO
FLOOR OR WALL, AND SLIDE RANGE BACK SO REAR
RANGE FOOT IS UNDER ANTI-TIP BRACKET.
■ WARNING:
heat or warm the room. Doing so may result in carbon monoxide
poisoning and overheating of the oven.
■
WARNING:
oven bottom or cover an entire rack with materials such as
aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings
may also trap heat, causing a fire hazard.
■ CAUTION:
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be seriously
injured.
Do Not Leave Children Alone – Children should not be left alone
■
or unattended in area where the range is in use. They should
never be allowed to sit or stand on any part of the range.
Wear Proper Apparel – Loose-fitting or hanging garments
■
should never be worn while using the range.
User Servicing – Do not repair or replace any part of the range
■
unless specifically recommended in the manual. All other
servicing should be referred to a qualified technician.
■ Storage in or on the Range – Flammable materials should not
be stored in an oven or near surface units.
Do Not Use Water on Grease Fires – Smother fire or flame or
■
use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let potholder
touch hot heating elements. Do not use a towel or other bulky
cloth.
■ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS –
Surface units may be hot even though they are dark in color.
Areas near surface units may become hot enough to cause
burns. During and after use, do not touch, or let clothing or
other flammable materials contact surface units or areas near
units until they have had sufficient time to cool. Among those
areas are the cooktop and surfaces facing the cooktop.
■ Never Leave Surface Units Unattended at High Heat Settings –
Boilover causes smoking and greasy spillovers
■ Glazed Cooking Utensils – Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed utensils
are suitable for range-top service without breaking due to the
sudden change in temperature.
■ Utensil Handles Should Be Turned Inward and Not Extend Over
Adjacent Surface Units – To reduce the risk of burns, ignition of
flammable materials, and spillage due to unintentional contact
with the utensil, the handle of a utensil should be positioned so
that it is turned inward, and does not extend over adjacent
surface units.
NEVER use this appliance as a space heater to
NEVER cover any slots, holes or passages in the
Do not store items of interest to children in
that may ignite.
■ Clean Cooktop With Caution – If a wet sponge or cloth
is used to wipe spills on a hot cooking area, be careful
to avoid steam burn. Some cleaners can produce
noxious fumes if applied to a hot surface.
■ Use Care When Opening Door – Let hot air or steam
escape before removing or replacing food.
Do Not Heat Unopened Food Containers – Build-up of
■
pressure may cause container to burst and result in
injury.
■ Keep Oven Vent Ducts Unobstructed.
■ Placement of Oven Racks – Always place oven racks in
desired location while oven is cool. If rack must be
moved while oven is hot, do not let potholder contact
hot heating element in oven.
■ DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN – Heating elements may be hot
even though they are dark in color. Interior surfaces of
an oven become hot enough to cause burns. During
and after use, do not touch, or let clothing or other
flammable materials contact heating elements or interior
surfaces of oven until they have had sufficient time to
cool. Other surfaces of the appliance may become hot
enough to cause burns – among these surfaces are
oven vent openings and surfaces near these openings,
oven doors, and windows of oven doors.
■ Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or,
in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. In Canada, the range
must be electrically grounded in accordance with
Canadian Electrical Code. Be sure the range is properly
installed and grounded by a qualified technician.
■ Disconnect the electrical supply before servicing the
appliance.
■ Injuries may result from the misuse of appliance doors
or drawers such as
stepping, leaning, or sitting on the
doors or drawers.
■ Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
■ Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
■ Do Not Clean Door Gasket – The door gasket is
essential for a good seal. Care should be taken not to
rub, damage, or move the gasket.
■ Do Not Use Oven Cleaners – No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
■ Clean Only Parts Listed in Manual.
■ Before Self-Cleaning the Oven – Remove broiler pan
and other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
For units with ventilating hood –
■ Clean Ventilating Hoods Frequently – Grease should not
be allowed to accumulate on hood or filter.
■ When flambéing foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
4
BE
D
A
KEY USAGE TIPS
AquaLift® Self-Cleaning Technology
AquaLift® Self-Cleaning Technology is a first-of-its-kind cleaning
solution designed to minimize the time, temperature, and odors
that ordinarily come with traditional self-cleaning methods. With
AquaLift® Self-Cleaning Technology, an exclusive coating on the
interior of the oven, is activated with heat and water to release
baked-on soil. To use AquaLift® Self-Cleaning Technology, simply
wipe out loose debris, pour water into the oven bottom, and run
the AquaLift® Self-Cleaning cycle. When the cycle finishes in under
1 hour at a lower temperature than in traditional self-cleaning
methods, just wipe out the remaining water and loose debris.
See the “Clean Cycle” section for more detailed instructions. For
additional information, frequently asked questions, and videos
on using AquaLift® Self-Cleaning Technology, visit our website at
http://whirlpoolcorp.com/aqualift.
Surface Temperatures
When the range is in use, all range surfaces may become hot,
such as the knobs and oven door.
Baking Drawer
When the oven is in use, the drawer may become hot. Do not store
plastics, cloth, or other items that could melt or burn in the drawer.
A
C
A. Small (S)
B. X-Large (XL)
Align the gas tube opening in the burner base with the orifice
holder on the cooktop and the igniter electrode with the notch in
the burner base.
C. Medium (M)D. Medium (M)
E. Large (L)
A
B
C
E
D
Oven Vent
The oven vent releases hot air and moisture from the oven and
should not be blocked or covered. Do not set plastics, paper, or
other items that could melt or burn near the oven vent.
Preheating
When beginning a Bake, Convect Bake, or Convect Roast cycle,
the oven will begin preheating after Start is pressed. The oven
will take approximately 12 to 15 minutes to reach 350°F (177°C)
with all of the oven racks provided with your oven inside the
oven cavity. Higher temperatures will take longer to preheat. The
preheat cycle rapidly increases the oven temperature. The actual
oven temperature will go above your set temperature to offset
the heat lost when your oven door is opened to insert food. This
ensures that when you place your food in the oven, the oven
will begin at the proper temperature. Insert your food when the
preheat tone sounds. Do not open the door during preheat before
the tone sounds.
Surface Burners
The burner bases and caps must be properly positioned before
cooking. Your range comes with 3 sizes of burners and caps.
Each round burner base is marked with a letter indicating the
burner size. Align the burner bases as shown in the following
illustration:
A. Burner cap
B. Gas tube opening
C. Burner base
Place the burner caps on the appropriate burner bases. Each
round burner cap is marked with a letter indicating the burner size.
Small cap (S) Medium cap (M) Large cap (L)X-Large cap (XL)
Burner caps should be level when properly positioned. If burner
caps are not properly positioned, surface burners will not light.
The burner cap should not rock or wobble when properly aligned.
A. Incorrect
B. Correct
D. Igniter electrode
E. Orifice holder
B
5
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Product Help section
of our website at www.kitchenaid.com for more detailed instructions. In Canada, refer to the Product Help Section at www.kitchenaid.ca.
WARNING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
KeypadFeatureInstructions
CLOCK/TOOLSClock
CLOCK/TOOLSSettings
OVEN LIGHTOven cavity light
TIMER SET/OFFOven timer
STARTCooking start
CANCEL UPPER
CANCEL LOWER
(on some models)
BAKE Baking and
Range function
roasting
The Clock can use a 12- or 24-hour cycle. See the “Electronic Oven Controls” section.
1. Press CLOCK/TOOLS until “CLOCK” is displayed.
2. Use the number keypads to set the time of day.
3. Press START to change the time.
4. Press “3” for AM or “6” for PM.
Enables you to personalize the audible tones and oven operation to suit your needs.
See the “Electronic Oven Controls” section.
The oven light is controlled by a keypad on the oven control panel. While the oven
door is closed, press OVEN LIGHT to turn the light On and Off. When the oven door is
opened, the oven light will automatically come On.
The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press the number keypads to set the length of time in hr-min-min. Leading zeros
do not have to be entered. For example, for 2 minutes, enter “2.”
3. Press TIMER SET/OFF to begin the countdown. If enabled, end-of-cycle tones will
sound at end of countdown.
4. Press TIMER SET/OFF again to cancel the Timer and return to the time of day.
Do not press the Cancel keypad because the oven will turn off.
5. If the Timer is running but not in the display, press TIMER SET/OFF to display the
countdown for 5 seconds.
The Start keypad begins any oven function. If Start is not pressed within 2 minutes after
pressing a keypad, the function is canceled and the time of day is displayed.
The Cancel keypad stops any function for the appropriate oven or drawer, except
the Clock and Timer.
1. Press BAKE.
2. Set the desired temperature between 170°F and 500°F (75°C and 260°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL UPPER when finished.
6
KeypadFeatureInstructions
STEAM BAKESteam bake
BROILBroiling
PROOFProofing bread
KEEP WARMHold warm
EASY CONVECT
BAKE
EASY CONVECT
BROIL
Convection
cooking
Convection
cooking
1. Insert the steam rack with water reservoir in the oven.
2. Pour 11/2 cups (350 mL) of warm water into the water reservoir.
NOTE: Do not fill past the MAX mark.
3. Press STEAM BAKE.
4. Press the number keypad to select the desired food option.
5. Press the number keypads to set the temperature.
6. Press START.
7. (Optional) Press COOK TIME. Press the number keypads to set the cook time.
8. Press START.
9. Insert food when preheating finishes.
10. Press CANCEL UPPER when finished.
NOTE: Let oven cool before removing and emptying water reservoir.
1. Press BROIL.
2. Press the number keypads to set the desired temperature.
3. Press START and allow the oven to preheat for 5 minutes.
4. To change the temperature, repeat steps 2 and 3.
5. Position the cookware in the oven, and then close the door.
6. Press CANCEL UPPER when finished.
1. Place prepared dough in oven. Press PROOF.
2. Press START.
Let the dough rise until nearly doubled in size. Proofing time may vary depending
on dough type and quantity.
3. Press CANCEL UPPER when finished proofing.
Refer to the “Proofing Bread” section for more information.
Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL UPPER when finished.
1. Press EASY CONVECT BAKE.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C) in 5°
increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. (Optional) Press the number keypads to set a cook time.
6. Press START.
7. To change the temperature, repeat steps 2 and 3.
8. Press CANCEL UPPER when finished.
1. Press EASY CONVECT BROIL.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C) in
5° increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. (Optional) Press the number keypads to set a cook time.
6. Press START.
7. To change the temperature, repeat steps 2 and 3.
8. Press CANCEL UPPER when finished.
7
KeypadFeatureInstructions
EASY CONVECT
ROAST
COOK TIMETimed cooking
DELAY STARTDelayed start
BAKING DRAWER
BAKE
(on some models)
BAKING DRAWER
SLOW COOK
(on some models)
BAKING DRAWER
KEEP WARM
(on some models)
AQUALIFT SELF
CLEAN
START
(Control Lock Hold
3 Sec)
CLOCK/TOOLSEnergy save
Convection
cooking
Baking drawer
Slow cook
drawer
Warming drawer
Clean cycle
Oven control
lockout
1. Press EASY CONVECT ROAST.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C)
in 5° increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. (Optional) Press the number keypads to set a cook time.
6. Press START.
7. To change the temperature, repeat steps 2 and 3.
8. Press CANCEL UPPER when finished.
Timed cooking allows the oven to be set to turn on at a certain time of day, cook for
a set length of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
The Delay Start keypad is used to enter the starting time for an oven function with
a delayed start. Delay Start should not be used for foods such as breads and cakes
because they may not bake properly.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
1. Press BAKING DRAWER BAKE.
2. Set the desired temperature between 170°F and 451°F (75°C and 233°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL LOWER when finished.
1. Press BAKING DRAWER SLOW COOK.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Place the food(s) in the baking drawer.
4. Press START.
5. (Optional) Set the desired cook time using the number keypads.
6. Press START to begin heating the baking drawer.
7. Press CANCEL LOWER when finished.
Food must be at serving temperature before placing it in the warmed oven.
1. Press BAKING DRAWER KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL LOWER when finished.
See the “Clean Cycle” section.
1. Check that the oven is OFF.
2. Press and hold START (Hold 3 Sec) for 3 seconds.
3. A tone will sound, and “Control Locked” will scroll, and then “Locked” will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked. The cooktop
functions are not affected by the oven control lockout.
1. Press CLOCK/ TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
If Energy Save is ON, the range will go into Sleep mode after 5 minutes of inactivity.
Any keypad press will activate the display. If Energy Save is OFF, the display will be
ON at all times.
8
Loading...
+ 18 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.