KitchenAid KBFC42FSS00, Architect KBFC42FSS, Overlay KBFO42FSX Installation Instructions Manual
Kitchen_kid ®
42"(106.7 CM) BOTTOM-MOUNT
BUILT-IN REFRIGERATOR
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.
REFRIGERADOR EMPOTILADO CON MONTAJE
INFERIOR DE 42" (106,7 CM)
IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACION REQUIERE DE 20 MAS PERSONAS.
P P P
REFRIGERATEUR ENCASTRE DE 42" (106,7 CM)
AVEC CONGELATEUR EN DESSOUS
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L'INSTALLATION NECESSITE L'INTERVENTION DE 2 PERSONNES OU PLUS.
Table of Contents/indice/Table des matieres .................................................................. 2
2309309
TABLE OF CONTENTS
REFRIGERATOR SAFETY ........................................................................... 3
MODELS ....................................................................................................... 4
INSTALLATION REQUIREMENTS ............................................................. 4
Tools and Parts ......................................................................................... 4
Location Requirements ............................................................................. 5
Electrical Requirements ............................................................................ 6
Water Supply Requirements ..................................................................... 6
Tipping Radius .......................................................................................... 6
Product Dimensions ................................................................................. 7
Door Swing Dimensions ........................................................................... 7
Handle and Door Clearances ................................................................... 8
Overlay Series Custom Panels ............................................................... 10
Custom Overlay Panel Dimensions ........................................................ 10
Architect '_Series Custom Side Panels .................................................... 11
Overlay Series Custom Side Panels ....................................................... 12
INSTALLATION INSTRUCTIONS ............................................................. 13
Unpack the Refrigerator ......................................................................... 13
Reduce Tipping Radius .......................................................................... 13
Move the Refrigerator into House .......................................................... 13
Install Anti-Tip Boards ............................................................................ 14
Connect the Water Supply ..................................................................... t 4
Plug in Refrigerator ................................................................................. 15
Move Refrigerator to Final Location ....................................................... 15
Lower Leveling Legs ............................................................................... 16
Install Overlay Series Custom Panels .................................................... 16
Level and Align Refrigerator ................................................................... 17
Adjust Doors ........................................................................................... 17
Install Side Panel .................................................................................... 18
Install Base Grille .................................................................................... 19
Complete Installation .............................................................................. 19
Water System Preparation ..................................................................... 19
P
INDICE
SEGURIDAD DEL REFRIGERADOR ........................................................ 20
MODELOS .................................................................................................. 21
REQUlSITOS DE INSTALACION .............................................................. 21
Piezas y herramientas ............................................................................. 21
Requisitos de ubicacion ......................................................................... 22
Requisitos el_ctricos ............................................................................... 23
Requisitos del suministro de agua ......................................................... 23
Arco de vuelco ........................................................................................ 24
Medidas del producto ............................................................................. 24
Medidas de oscilacion de la puerta ........................................................ 25
Espacios para la agarradera y la puerta ................................................. 26
Paneles a la medida de la Serie Overlay ................................................ 28
Dimensiones del panel recubierto a la medida ...................................... 29
Paneles laterales a la medida para la Serie Architect '_........................... 30
Paneles laterales a la medida para la Serie Overlay .............................. 30
INSTRUCCIONES DE INSTALACION ...................................................... 31
Desempaque el refrigerador ................................................................... 31
C6mo reducir el arco de vuelco ............................................................. 32
C6mo hacer entrar el refrigerador en la casa ........................................ 32
C6mo instalar los tableros antivuelco .................................................... 32
Conexion del suministro de agua ........................................................... 33
C6mo enchufar el refrigerador ............................................................... 34
Ubicacion final del refrigerador .............................................................. 34
Baje las patas niveladoras ...................................................................... 35
C6mo instalar los paneles a la medida para la Serie Overlay ............... 35
Nivelaci6n y alineamiento del refrigerador ............................................. 36
C6mo ajustar las puertas ....................................................................... 36
C6mo instalar el panel lateral ................................................................. 38
C6mo instalar la rejilla de la base ........................................................... 38
C6mo terminar la instalacion .................................................................. 39
Preparaci6n del sistema de agua ........................................................... 39
TABLE DES MATIERES
SF:CURITE DU RF:FRIGF:RATEUR ........................................................... 40
MOD#LES .................................................................................................. 41
EXIGENCES D'INSTALLATION ................................................................ 41
Outillage et pieces .................................................................................. 41
Exigences d'emplacement ..................................................................... 42
Specifications _lectriques ...................................................................... 43
Specifications de ralimentation en eau .................................................. 43
Rayon de basculement ........................................................................... 44
Dimensions du produit ............................................................................ 44
Dimensions pour le pivotement des portes ........................................... 45
D_gagements pour les poign_es et portes ............................................ 46
Panneaux personnalis_s de la s_rie Overlay .......................................... 48
Panneaux personnalis_s - Dimensions .................................................. 49
Panneaux lat_raux personnalis_s de la S_rie Architect ®....................... 50
Panneaux lat_raux personnalis_s des S_ries Overlay ........................... 50
INSTRUCTIONS D'INSTALLATION ......................................................... 51
D_ballage du r_frig_rateur ...................................................................... 51
R_duction du rayon de basculement ..................................................... 52
Faire entrer le r_frig_rateur dans le domicile .......................................... 52
Installation de planches antibasculement .............................................. 52
Raccordement & la canalisation d'eau ................................................... 53
Brancher le r_frig_rateur ......................................................................... 54
D_placement du r_frig_rateur & I'emplacement final ............................. 54
D_ploiement des pieds de nivellement .................................................. 55
Installation des panneaux personnalis_s de la S_rie Overlay ................ 55
Alignement et aplomb du r_frig_rateur .................................................. 56
Ajustement des portes ............................................................................ 56
Installation du panneau lateral ................................................................ 58
Installation de la grille de la base ........................................................... 58
Achever rinstallation ............................................................................... 59
Preparation du systeme d'eau ............................................................... 59
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
MODELS
(
Architect _ Series Overlay Series
Features wraparound styling that complements the contoured door Features factory-installed, overlay style trim, to provide a
handles. This series provides a warm commercial-looking built-in "frameless" look. This series requires the installation of custom
refrigerator, panels, handles, and standoffs.
KBFC42FSS KBFO42FSX
INSTALLATION REQUIREMENTS
IMPORTANT:
• Installer: Leave Installation Instructions with the homeowner.
• Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector's use.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
• Hand drill or electric drill • Torx_t T27 screwdriver
(properly grounded)
• Drill bits • 11/32"nut driver
• Two adjustable wrenches • %",1/4", and 1/2"open-end
wrenches
• Phillips screwdriver • %2" Allen wrench
• Small level • %" and %6" socket drivers
• Appliance dolly • Tape measure
PARTS NEEDED:
• Six #8 x 3" (7.6 cm)wood screws (longer screws may be needed)
• One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
• Order factory panels, make custom panels or consult a
qualified cabinetmaker or carpenter to make the panels.
Overlay Series: Make custom panels, or consult a qualified
cabinetmaker or carpenter to make the panels. See "Design
Specifications" for more information.
Architect ®and Pro Line®Series are shipped complete.
• If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
1/4"(6.35 mm) compression fitting.
1-®TORX is a registered trademark of Textron Innovations Inc.
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
• A grounded 3 prong electrical outlet should be placed within
4" (10.2 cm) of the right side cabinets or end panel. See
"Electrical Requirements" for additional information.
• The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor or the
back wall. See "Water Supply Requirements" for more specific
information.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT:
• Observe all governing codes and ordinances.
• It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source.
• Do not install in a location where the temperature will fall
below 55°F (13°C).
• Floor must support the refrigerator weight, more than
600 Ibs (272 kg), door panels and contents of the
refrigerator.
• Ceiling height must allow for side tipping radius. See
"Tipping Radius."
• Location should permit door to open fully. See "Door
Swing Dimensions."
• Location must permit top grille removal. See "Opening
Dimensions."
Opening Dimensions
• The solid soffit must be within 1" (2.5 cm) maximum above the
refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is
not available, then the refrigerator must be braced to prevent
tipping during use.
If the anti-tip boards are needed, they must be attached to the
rear wall studs 80" to 90" (203 - 229 cm) above the floor. See
"Install Anti-Tip Boards" for more information.
NOTE: A clearance of 1/2"(1.3 cm) must be maintained in front
of the refrigerator's side trim in order for the top grille to be
removed.
il
====00"-90"
!! (203-229 cm)!!
!! !!
cm) rain.
043/4" (215 cm) max.
to bottom of solid soffit
411/2" to 413/4 ''
(105.4 cm to 106.0 cm)
1
H
6" _'/
(2.5 cm)
i.2 cm)
24"
(61 cm) min.
NOTE: Flooring under refrigerator must be at same level as the
room.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
IMPORTANT: Ifthis product is connected to a GFCI (Ground Fault
Circuit Interrupter) protected outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Food quality
and flavor may be affected. If nuisance tripping has occurred, and
if the condition of the food appears poor, dispose of it.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, remove the top grille and turn the master
power switch to OFF or disconnect power at the circuit breaker
box.
When you are finished, turn ON the master power switch or
reconnect power at the circuit breaker box. Then reset the control
to the desired setting.
• If the water shutoff valve is not in the cabinets, the plumbing
for the water line can come through the floor. A 1/2"(12.7 mm)
hole for plumbing should be drilled at least 6" (15.2 cm) from
the right or left hand side cabinet or panel. On the floor, the
hole should be no more than 1" (2.54 cm) away from the back
wall. See "Connect the Water Supply."
• If additional tubing is needed, use copper tubing and check
for leaks. Install the copper tubing only in areas where the
household temperatures will remain above freezing.
• Do not use a piercing-type or 3/16"(4.76 mm) saddle valve
which reduces water flow and clogs more easily.
NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shutoff valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Water Pressure
A cold water supply with water pressure between 30 and 120 psi
(207 - 827 kPa) is required to operate the water dispenser and ice
maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 - 414 kPa):
• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
• If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Wsi t
All installations must meet local plumbing code requirements.
The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. The right-hand side is recommended. The access hole
through the cabinet must be within 1/,,,(12.7 mm) of the rear
wall.
NOTE: If the water shut off valve is in the back wall behind the
refrigerator, it must be at an angle so that the tube is not
kinked when the refrigerator is pushed into its final position.
t
1"
(2.54 cm)
24"
(60.96 cm) min,
Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
• The dolly wheel height must be added to the tipping radius
when a dolly is used.
• If needed, the tipping radius can be reduced. See "Reduce
Tipping Radius."
Side Tipping Radius
A. Tip this side only
Side View
• The depth from the front of the top grille to the back of the
refrigerator cabinet is 25%" (64.4 cm).
• The power cord is 84" (213 cm) long.
• The water line attached to the back of the refrigerator is 5 ft
(1.5 m) long. Height dimensions are shown with leveling legs
extended 1/8"(3 mm) below the rollers.
253/8-
(64.4 cm)
231/2"
(60 cm)
.833/8,,
(211.6cm)
84" (213 cm)
Power Cord
31/2" (9 cm)
*When leveling legs are fully extended to 11/4"(3.2 cm) below
rollers, add 11/8"(2.9 cm) to the height dimensions.
Top View
41 I/4"
(105 cm)
25%"
(64.5 cm)
!
Front View
• Width dimensions were measured from trim edge to trim
edge.
• Height dimensions are shown with leveling legs extended 1/8"
(3 mm) below the rollers.
_-_ 421/4'' (107.3 crn)_
.833/8"
(211.6 cm)
L
*When leveling legs are fully extended to 11/4"(3.2 cm) below
rollers, add 11/8"(2.9 cm) to the height dimensions.
The location must permit the door to open to a minimum of 90°.
Allow 41/2'' (11.4 cm) minimum space between the side of the
refrigerator and a corner wall.
NOTE: More clearance may be required if you are using overlay
panels or custom handles.
Toadjust the door swing, see "Adjust Door Swing."
42" (106.7 cm} Models
÷
407/16 ''
(102.7 cm)
131/2 ''
(34.3 cm)
H
437/16"
(110,3 cm)
Ifyou are installing custom panels, the panels must allow certain clearances for the handles and for the door to swing open. First,
determine the types of handles you will be using and the door stop setting. Then, choose the appropriate scale drawing to use as a
template for creating the panels.
Door Swing 110 °
Actual Size
I
®
NOTE: For Overlay Series models, rout the
hinge side of the custom door panels to a
radius that is equal to at least half the
thickness of the panel if a 130°door swing is
desired. See "Adjust Doors."
O
Hinge
Refrigerator to
Cabinetry Clearance
Refrigerator
Side Trim
Cabinetry
NOTE: Allow 1/2"
(1.3 cm) clearance
between overlay
panel and cabinetry.
3/4"
(1.9 cm)
Panel
I
I
[
Hinge
Spacer Pane
Door Swing 90 °
Actual Size
Refrigerator to
Cabinetry Clearance
Refrigerator
Side Trim
(2.5 cm)
3/4"
(1.9 cm)
1 Jl i
/2 ,,
(1.3,cm)i
i J
i i
i i
1/4"(6.35 mm)
1/2 (1.3 cm)
.... q.............. 3/4"(1.9 cm)
i
L
1/2"
(1.3cm)
3/4"
(1.9cm) i
J 1"
(2.5cm)
0
<
6-
1 1/4"
(3.2cm)
11/2"
(3.8cm)
1" (2.5 cm)
_ .... _ ..... C_ .., _ ..... " _ ....
Custom overlay panels allow you to blend the exterior of your
refrigerator into the overall kitchen decor and to use custom
handles for additional design flexibility.
The custom panels must have backer panels attached in order to
mount them to the refrigerator. It is most common to work with
three panels, as shown in the following graphic: a decorative
overlay panel, a %" (3.18 mm) spacer panel or spacer strips and a
V4" (6.35 mm) backer panel.
[ OveMayPanel Sp_ce_P_no,1
Backer Panel
(15.88 to W'
19.05 ram) 1/_,, (6.35 rnm)
(3.18 mm)
Spacer Panel _--
1/8"
-r-i ,
_-_ 1" rnir_irnurn
I Ii (2.54 cm),, ..... "
[ _d_r/Gdl,e Trim
_ll _Offset Dimension
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimension and placement instructions to be sure that the
custom overlay panels will fit properly.
IMPORTANT:
• The weight of the refrigerator door overlay panel cannot
exceed 35 Ibs (15.9 kg).
• The weight of the freezer drawer overlay panel cannot exceed
30 Ibs (13.5 kg).
• The weight of the top grille overlay panel cannot exceed
10 Ibs (4.5 kg).
To minimize panel weight, you may use 2" (5.08 cm) spacer strips
around the perimeter in place of full-sheet solid spacer panels.
The spacer strips must be set in at least 1" (2.54 cm) from the top,
bottom and side edges of the backer panel. If you use spacer
strips, it is also recommended that you use two 2" (5.08 cm) strips
horizontally centered for added support.
9' d_ f,
Custom Overlay Panels Custom Backer Panels
7,h,,TJ
(16.4 cm)£ J
40%"
(102.6 cm) I-- (100.639%"cm) _I
TOP GRILLE PANEL i I" * i _-6114''
Maximum Weight: 10 ibs (4.5 kg) , _ _(15.9 cm)
..<_Side Offset _ Bottom Offset
3/8 (9.5 mm)
(50.820"cm)÷II-'-(50280"cm) V2" (1.27 cm)
T
511/4"
(130.2 cm)
REFRIGERATOR
DOOR PANEL
MaximumWeight:
35 Ibs (15.9 kg)
REFRIGERATOR
DOOR PANEL
Maximum Weight:
35 Ibs (15.9kg)
T
51%"
(130.2cm)
T
201/4 ,'
(51.4 cm)
!
40%"
< (102.6 cm)
FREEZER DOOR PANEL
MaximumWeight:30 Ibs (13.6 kg)
Spacer Panels
Side __.
Offset
3/16 _
(4.7 ram)
19%" --_
9.85 cm)
493h6,'
(124.93 cm)
Bottom
Offset
1/2_
(1.27 cm)
,,,,,,,,,,,,,,,,,Exterior
Panel
,2- '
_ extends
_ above
19%" _ door.
i 1(49.85cm)
49sh6''
124.93 cm)
__..___Side
Offset
3/16 _
(4.7 ram)
Bottom
Offset
(1.27 cm). _
..... _ _!
i
!-i--f ,o.
I (101.6cm)
19z/8"
(50.48 cm)
....... i
I
-_ center
Backer
................Panel
left to
right
_[ Offset all sides
_h_"(4.7 mm)
NOTE: Spacer panels must be at least 1" (2.54 cm) from the top, bottom, and side edges of the backer panel.
10
3-PieceGrilleOverlayPanelConfiguration
TopView SideView
A. _" (1.27 cm) Decorative
overlay panel
B. _" (3.18 mm) Spacer panel
C. ¼" (6.25 mm) Backer panel
(2.54 cm)
V2"(1.27 cm)
3-Piece Door Overlay Panel Configuration
J
J
B C D
A. Offset dimension
B. ¼" (6.25 mm) Backer panel
C. _" (3.!6 mm) Spacer panel
D. _" (1.92 cm) Decorative overlay panel
1-Piece Overlay Panel Configuration
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimesions and placement instructions to be sure that the
custom overlay panels will fit properly.
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed and the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
• The dimensions shown are actual product dimensions and
may not reflect the needed panel installation dimensions.
• The side panel should be a minimum of 1/2"(1.27 cm) thick
to prevent warping.
• If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on the rear wall.
Refrigerator
241/8,,
(61.3 cm)
(60,3 cm)
231/2'.
(59,7 cm)
Side Trim
1/4"
(6.35 mm)
3/16"
(4,7 mm) /
7/32,,/
(5"5 mm) I
1%2"(10ram) %"
(15,7ram)
Inset Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall. Add 7/32,,(5.6 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than 1/4"(6.35 mm) thick, route the front
edge to allow the side panel to fit into the trim.
Flush Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall.
2. Attach the support board with a screw or adhesive that is
compatible with aluminum and wood.
11
Recessed Inset Installation Dimensions
1. Measure the distance from point A (as shown) to back wall.
2. Route the front edge of the support board or attach a 1/4"
(6.35 mm) board to hold the panel in the cabinet side trim.
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed and the end of a cabinet run. You
may choose an Inset or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
• The dimensions shown are actual product dimensions and
may not reflect the needed installation dimensions.
• The side panel should be a minimum of 1/2"(1.27 cm) thick
to prevent warping.
• If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on the rear wall.
Refrigerator
Side Trim
3_8"
(9.7 mm)
3_161'
--_" _--- (4.5 ram)
V16"
(1.5 ram)
Vs"
(3.2 mrn)
Inset Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall. Add 1/32,,(0.8 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than %" (9.5 mm) thick, route the front
edge to allow the side panel to fit into the trim.
Recessed Inset Installation Dimensions
1. Measure the distance from point A (as shown) to back wall.
2. Route the front edge of the support board or attach a %"
(9.5 mm) board to hold the panel in the cabinet side trim.
12
INSTALLATION INSTRUCTIONS
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
IMPORTANT:
• Do not remove the protective film until the refrigerator is in its
operating position.
• All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
• Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating position.
1. Remove and save the literature package and parts bag taped
to the refrigerator door. Remove the four brackets (two on
each side) that attach the shipping base to the refrigerator
bottom.
NOTE: Do not remove tape and door bracing until the
refrigerator is in its final position.
2. If necessary, reduce the tipping radius. See "Tipping Radius"
for ceiling height requirements or "Reduce Tipping Radius" for
step-by-step instructions. If you do not need to reduce the
tipping radius, proceed to "Move the Refrigerator into House."
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
"Tipping Radius" in the "Design Specifications" section for more
information.
Ifyou do not have adequate ceiling height to stand the refrigerator
upright, the tipping radius can be reduced by removing the top
grille and side trims (see the following chart).
4M2_ Reduced Tipping Radius
88W' (224.8 cm)
Architect _ and Overlay Series
1. Grasp both ends of the top grille.
2. Push the top grille straight up; then pull straight out. Lay the
grille on a soft surface.
B A B
A. Top grille
B. Cabinet side trim
Remove the six screws attaching each cabinet side trim to the
refrigerator and remove the side trims.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
1. Place an appliance dolly under the left side of the refrigerator
as shown. Be sure to protect the side trims and handles. Place
the corner posts from the packing materials over the trims and
handles as appropriate. Slowly tighten the strap.
NOTE: Pass the dolly strap under the handles for the
Architect ®Series.
13
2. Place pieces of the shipping carton on the floor when rolling
the dolly and refrigerator into the house. Move the refrigerator
close to the built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
4. Do not remove protective film or cover.
5. If necessary, reassemble the trim and top grille after the dolly
has been removed from the refrigerator.
_ _ _ _ _ _ _.._._,_ _i¸_, ._
IMPORTANT:
• The solid soffit must be within 1" (2.5 cm) maximum above the
refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is
not available, prevent the refrigerator from tipping during use.
• It is recommended that board(s) be installed before the
refrigerator is installed.
• Board(s) must be long enough to fully cover the width of the
compressor cover.
• Locate the board(s) so the bottom surface(s) of the board(s)
is(are) 84" (213 cm) from the floor.
• During installation, raise the refrigerator up so there is 1/4"
(6.35 mm) maximum between the top of the refrigerator and
the bottom of the anti-tip board(s). Do not crush the
condenser cover when raising the rear leveling legs.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall 80" to 90" (203 cm to
229 cm) above floor.
2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x
81 cm) boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws
must be screwed into the studs at least 11/2'' (3.8 cm). The
board(s) must overlap the compressor cover.
A B
2" (5 cm)
D
A. Center board _" (6.35 mm) max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
C. Attach to studs with six #8 x 3" (7.6 cm) screws
D. Compressor cover
Read all directions before you begin.
IMPORTANT: Ifyou turn the refrigerator on before the water line is
connected, turn the ice maker OFR
Style I - Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1, see
"Style 2 - Copper Line Connection."
1. Unplug refrigerator or disconnect power supply.
IMPORTANT: Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear. Flushing the
water line may prevent clogged filters and/or water valves.
2. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
3. Thread the provided nut onto the shutoff valve as shown.
A
J/ll
B
C
A. Bulb
B. Nut
C. Water tubing
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
6. Plug inthe refrigerator or reconnect power.
7. Flush the water system. See "Water System Preparation."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Style 2 - Copper Line Connection
Connecting to Water Line
NOTE: If existing water line meets the "Water System
Requirements," see "Connecting to Refrigerator."
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
14
5. Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold
water pipe you have selected.
................... A
G J ..............B
_ ........ C
F E D v
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten, or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten the
clamp or the sleeve. This will crush the copper tubing.
IMPORTANT: Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear. Flushing the
water line may prevent clogged filters and/or water valves.
8. Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9. Check for leaks around the saddle valve.
Connecting to Refrigerator
1. Unplug the refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
3. Measure the distance from the shutoff valve to the opening in
which the refrigerator will be located. Tubing must be
extended from the shutoff valve into the refrigerator opening
following specific guidelines. See "Water Supply
Requirements."
4. A 1/4"x 1/4"(6.35 mm to 6.35 mm) coupling is needed in order
to connect the water tubing to an existing household water
line. Thread the provided nut onto the coupling on the end of
the copper tubing.
A B C D E F G
A. Water tubing E. Ferrule (purchased)
B.Nut F Nut (purchased)
C. Bulb G. Household water line (as
D. Coupling (purchased) connected in previous section)
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
7. Plug in the refrigerator or reconnect power.
8. Flush the water system. See "Water System Preparation."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Set control switch at top of cabinet to the OFF position.
2. Plug into a grounded 3 prong outlet.
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
IMPORTANT: To prevent floor damage, make sure levelers are
raised (not touching floor) and refrigerator is on rollers before
moving.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
2. Do not remove protective film or cover.
3. Move the refrigerator straight back and evenly into the
opening. Be sure that cabinet side trims are not interfering
with door opening. Be sure that water tubing is not kinked and
the power supply cord is on top of the refrigerator.
15
NOTE: All four leveling legs must contact the floor to support and
stabilize the full weight of refrigerator. Rollers are for moving
refrigerator and not for permanent support.
Use a %6" socket wrench to turn the leveling bolts clockwise to
lower the 4 leveling legs until refrigerator weight is supported by
leveling legs. The rollers should be off the floor. To avoid cabinet
damage, do not apply more than 50 inch-pounds (58 cm - kg) of
torque to the leveling legs.
A. Rear leveling legs
B. Front leveling legs
IMPORTANT:
• Install the custom handles prior to installing the panels on
the refrigerator. For more information on KitchenAid
custom handle selection, refer to the KitchenAid Catalog,
visit wvtw.kitchenaid.com, or call 1-800-422-1230.
In Canada, visit wvwv.KitchenAid.ca, or call
1-800-807-6777.
• Create custom door overlay panels according to the
specifications in the "Overlay Series Custom Panels"
section.
• KitchenAid is not responsible for the removal or addition of
molding or decorative panels that would prevent the
refrigerator from being serviced.
Door Panel Installation
1. Remove all tape and door bracing from the refrigerator door
and freezer drawer.
2. Open the refrigerator doors and freezer drawer and remove
the trims and corner caps on each door as shown.
I .......A
R
B ..................... .,B
I
\
A A
3. Slide the custom panels into the trims on the refrigerator door
and freezer drawer, making sure that the backer panel fits into
the hinge side trims.
A _ _oA
A. Panels
4. Reinstall the trims and corner caps.
5. Remove the protective skin from the screw covers. Snap the
screw covers into the handle trim section.
Top Grille Panel
1. Grasp both ends of the top grille.
2. Push straight up; then pull straight out. Place the top grille
panel-side down on a soft working surface.
A. Top grille
B. Cabinet side trims
A. Comer caps
B. Refrigerator door trims
C. Freezer drawer trim
16
3=
4=
Remove one end cap by loosening the nuts and sliding the
end cap off.
A
A. Bottom rail C. End cap
B. Nuts D. Toprail
Slide the custom panel into the top grille channel and reattach
the end cap.
Door Height Adjustment
Use the following steps to adjust the door height, up or down,
after the refrigerator has been leveled.
NOTE: Adjust the right door to the position of the left door first. If
it is necessary to adjust the left door, you must make sure that the
hinged center rail located on the left-hand door does not drag
when closing the door.
1. Open the freezer drawer. Remove the locking plate screw from
the bottom side of the refrigerator door hinge using a
1/4"open-end wrench.
5=
A
A. Custompanel
Replace the top grille in the cabinet side trims and pull the
panel down slightly to lock it into place.
B A B
A B C
A. Bushing
B. Locking plate
C. Locking plate screw
2. Remove the locking plate as shown.
A. Top grille
B. Cabinet side trims
NOTE: Leveling legs can be extended a maximum of 11/4''
(3.18 cm) below the rollers. Adjustments may have to be done in
increments to keep from damaging the cab trim. Rotating the
leveling bolts clockwise extends the leveling legs and raises the
product.
1. Continue adjusting leveling legs to raise the refrigerator to the
anti-tip position. See "Install Anti-tip Boards."
2. Level/align the refrigerator from left to right by using leveling
bolts to adjust the front (and rear) leveling legs.
3. Level the product from front to back and align with the
cabinetry face.
A. Rear leveling bolt
B. Front leveling bolt
4. Be sure that all four leveling legs contact the floor and support
the full weight of the refrigerator.
5. Make final check to ensure the refrigerator is level and aligned
and is in the proper anti-tip position.
3. Turn the bushing located underneath the bottom of the hinge
using a W' open-end wrench. Turning the bushing to the left
will lower the door. Turning the bushing right will raise the
door.
4. After adjusting, check the doors to make sure they are even at
the top and bottom. If the doors are not even, continue to turn
the bushing to adjust the door.
5. Replace the locking plate.
• Turn the bushing slightly to align the hinge and locking
plate screw holes.
• Replace and tighten the locking plate screw.
6. Make final check to make sure the doors are aligned and
even.
Door Swing Adjustment
1. Check that the refrigerator door can open freely. If the door
opens too wide, you will have to adjust the door stop position.
2. Grasp both ends of the top grille.
17
3.
4.
5.
A
6.
Push the top grille straight up; then pull straight out. Lay the
grille on a soft surface.
B
A. Top grille
B. Cabinet side trims
The door stop is located on the top hinge.
A
\\
B
A. Door stop screw "A"
B. Doorstop screw "B"
C. Doorstop
Remove the 2 door stop screws.
• To remove the outer screw ("A"):
With the door closed, firmly press the L-shaped bracket
towards the center of the refrigerator until the screw is
exposed.
• To remove the inner screw ("B"):
Open the door 90° and the L-shaped bracket will expose
the screw.
\
A. Doorstop screw "A"
B. Doorstop screw "B"
Reverse or rotate the door stop to the desired position as
shown below.
NOTE: For Overlay Series models, rout the hinge side of the
custom door panels to a radius that is equal to at least half the
thickness of the panel if a 130 ° door swing is desired.
@
@
130° 110°
@
90 ° 90 °
Left-hand as shown; Right-hand reversed
7. Replace the door stop screws and tighten.
8. Check that the door can open freely.
If the built-in area depth is 25" (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT: KitchenAid is not responsible for the removal or
addition of molding or decorative panels that would prevent the
refrigerator from being serviced.
1. For the inside side trim piece, slide the front edge of the
routed side panel into the trim piece.
2. Nail the rear edge of the panel to the support board.
A
B
A. Support board
B. Side trim piece
18
Loading...