KitchenAid KUIS18PNZW0, KUIS18PNZB0, KUIS18NNZW0, KUIS18NNZB0, KUIC18PNZS0 Owner’s Manual

...

itchenAid _

FOR THE WAY IT'S MADE._

ICE MAKER

Use & Care Gude

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at...

In Canada, for assistance, installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com

www.KitchenAid.ca

FABRICA DE HIELO

Manua de uso ycu dado

Para consultas respecto a caracteristicas, funcionamiento/desempefio, piezas, accesorios o servicio, lame al: 1-800-422-1230

En Canada, para obtener ayuda, instalaci6n o servicio Ilame al: 1-800 807-6777 o visite nuestra pagina de Internet...

o visite nuestra pagina de Internet...

www.kitchenaid.com

www.kitchenaid.ca

MACHINE A GLAC_ONS

Guded'ut satonetd'entreten

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site Web a...

Table of Contents/[ndice/Table des matieres .................................................................. 2

www.KitchenAid.ca

W10515677B

TABLE OF

CONTENTS

ICE MAKER SAFETY ...................................................................... 3

INSTALLATION INSTRUCTIONS .................................................. 3

Unpack the Ice Maker .................................................................. 3

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 4

Water Supply Requirements ........................................................ 4

Vacation or Extended Time Without Use..................................... 5

Connect Water Supply ................................................................. 5

Ice Maker Drain Pump Installation............................................... 6

Drain Connection ......................................................................... 9

Leveling ........................................................................................ 9

Water FiltrationSystem .............................................................. 10

ICE MAKER USE .......................................................................... 11

How Your Ice Maker Works ....................................................... 11

Using the Controls ..................................................................... 11

Normal Sounds .......................................................................... 12

JNDICE

SEGURIDAD DE LA FABRICA DE HIELO .................................. 21

INSTRUCCIONES DE INSTALACION ......................................... 22

Desempaque la fabrica de hielo ................................................ 22

Requisitos de ubicaci6n ............................................................. 22

Requisitos electricos .................................................................. 22

Requisitos del suministro de agua ............................................. 23

Vacaciones o tiempo prolongado sin uso ................................. 23

Conexion del suministro de agua .............................................. 23

Instalacion de la bomba de desagQe de lafabrica de hielo ...... 24

Conexion del desagQe ............................................................... 27

Nivelacion ................................................................................... 28

Sistema de filtracion de agua .................................................... 29

USO DE LA FABRICA DE HIELO ................................................ 30

Como funciona su fabrica de hielo ............................................ 30

Uso de loscontroles .................................................................. 30

Sonidos normales ...................................................................... 31

ICE MAKER CARE ........................................................................ 12

Cleaning ...................................................................................... 12

Vacation and Moving Care ......................................................... 14

TROUBLESHOOTING .................................................................. 15

Ice Maker Operation ................................................................... 15

Ice Production ............................................................................ 16

Ice Quality ................................................................................... 16

Plumbing Problems .................................................................... 17

ASSISTANCE OR SERVICE ......................................................... 17

In the U.S.A................................................................................ 17

In Canada ................................................................................... 17

Accessories ................................................................................ 18

PERFORMANCE DATA SHEET ................................................... 18

WAR RANTY .................................................................................. 19

CUlDADO DE LA FABRICA DE HIELO ....................................... 31

Limpieza ..................................................................................... 31

Cuidado durante las vacaciones y mudanzas ........................... 34

SOLUCION DE PROBLEMAS ...................................................... 35

Funcionamiento de la fabrica de hielo ....................................... 35

Producci6n de hielo ................................................................... 36

Calidad del hielo ......................................................................... 36

Problemas de plomeria .............................................................. 37

AYUDA O SERVICIO TI_CNICO ................................................... 37

En los EE.UU .............................................................................. 37

Accesorios .................................................................................. 38

HOJA DE DATOS DEL RENDIMIENTO ...................................... 38

GARANTiA ..................................................................................... 39

TABLE DES

SI_CURITI_ DE LA MACHINE .&,GLAQONS ................................ 41

INSTRUCTIONS D'INSTALLATION ............................................ 42

Deballage de la machine &glagons ........................................... 42

Exigences d'installation ............................................................. 42

Specifications electriques .......................................................... 42

Specifications de ralimentation en eau ..................................... 43

Vacances ou Iongue periode d'inutilisation ............................... 43

Raccordement a la canalisation d'eau ...................................... 43

Installation de la pompe de vidange de la

machine & gla£sons..................................................................... 44

Raccordement au conduit vidange ............................................ 47

Nivellement ................................................................................. 48

Systeme de filtration d'eau ........................................................ 49

UTILISATION DE LA MACHINE ._ GLAQONS ............................ 50

Fonctionnement de la machine a gla_ons ................................. 50

Utilisation des commandes ........................................................ 50

Bruits normaux ........................................................................... 51

MATII RES

ENTRETIEN DE LA MACHINE .&GLAQONS .............................. 51

Nettoyage ................................................................................... 51

Precautions & prendre pour les vacances

ou le demenagement .................................................................. 53

DI_PANNAGE ................................................................................. 54

Fonctionnement de la machine & gla(;ons ................................. 54

Production de gla£sons............................................................... 55

Qualite des gla£sons.................................................................... 56

Problemes de plomberie ............................................................ 56

ASSISTANCE OU SERVICE ......................................................... 57

Aux #tats-Unis ............................................................................ 57

Au Canada .................................................................................. 57

Accessoires ................................................................................ 58

FEUlLLE DE DONNI_ES SUR LA PERFORMANCE ................... 58

GARANTIE ..................................................................................... 59

ICE MAKER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

Plug into a grounded 3 prong outlet. • Disconnect power before manually cleaning the inside components. Do not remove ground prong. • Disconnect power before servicing.

Do not use an adapter. • Replace all parts and panels before operating. Do not use an extension cord. • Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

INSTALLATION INSTRUCTIONS

Unpack the Ice Maker

Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your

ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in

the "Ice Maker Care" section.

Locat on Requ rements

• To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

• Installation of the ice maker requires a cold water supply inlet of 1/4"(6.35 mm) OD soft copper tubing with a shutoff valve or a Whirlpool supply line Part Number 8212547RB, and a Whirlpool approved drain pump, Part Number 1901A, only to carry the water to an existing drain.

• Choose a well ventilated area with temperatures above 55°F (13°C) and below 100°F (38°C). Best results are obtained between 70°F and 90°F (21°C and 32°C).

• This ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray or drips.

• When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as

shown. NOTES:

• Check that the power supply cord is not damaged, or

pinched or kinked between the ice maker and the cabinet.

• Check that the water supply line is not damaged, or

pinched or kinked between the ice maker and the cabinet.

• Check that the drain line (on some models) is not

damaged, or pinched or kinked between the ice maker and the cabinet.

34"

(86.4 cm)

Min.

341/2''

(87.6 cm)

Max.

281/2.

(72.4 cm)

Electr cal Requ rements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical

connection: A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice maker, be provided. Use a receptacle which cannot be turned off by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Ice quality may be affected. If nuisance tripping has occurred, and if the condition of the ice appears poor, dispose of it.

Recommended Grounding Method The ice maker must be grounded. The ice maker is equipped with

a power supply cord having a 3 prong grounding plug. The cord must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

24 II

60.1 cm)

18" m_=,-

(45.7 cm)

A. Recommended location for electrical and plumbing fixtures B. Floor level

Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See the "Leveling" section.

Water Supply Requ rements

Check that the water supply lines are insulated against freezing conditions. Ice formations in the supply lines can increase water pressure and damage your ice maker or home. Damage from frozen supply lines is not covered by the warranty.

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT:

• A reverse osmosis water filtration system is not recommended for ice makers that have a drain pump

installed.

• For gravity drain systems only.

• The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the ice maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of water per hour to the ice maker for proper ice maker operation. If a reverse osmosis system is desired, only a whole-house capacity reverse osmosis system, capable of maintaining the steady water supply required by the ice maker, is recommended. Faucet capacity reverse osmosis systems are not able to maintain the steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system isblocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Vacat on or Extended Tree W thout Use

When you will not be using the ice maker for an extended period of time, turn off the water and power supply to the ice

maker. Check that the water supply lines are insulated against

freezing conditions. Ice formations in the supply lines can increase water pressure and cause damage to your ice maker or home. Damage from freezing is not covered by the warranty.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances.

• Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

• Install tubing only in areas where temperatures will remain above freezing.

Tools Needed

Gather the required tools and parts before starting installation:

• Flat-blade screwdriver

• 7/16"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver NOTE: Do not use a piercing-type or 3/16"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

Connecting the Water Line

Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

Using a 1/2"copper supply line with a quarter-turn shutoff valve or the equivalent, connect the ice maker as shown.

NOTE: To allow sufficient water flow to the ice maker a minimum 1/2"diameter home supply line is recommended.

II |

A. Bulb B. Nut

Now you are ready to connect the copper tubing. Use 1/4" (6.35 mm) OD soft copper tubing for the cold water supply.

• Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut

square.

• Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

..........A

A. Compression sleeve B. Compression nut

C. Copper tubing

4. Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

IMPORTANT: Always drain the water line before making the final connection to the inlet of the water valve to avoid

possible water valve malfunction.

5. Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown.

Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

Rear View

• 8/le"ID x 32" (81 cm) vent tube (drain pump reservoir vent to ice maker cabinet back)

• Cable clamps (secures vent tube to back of ice maker) (3)

• #8-32 x 3/8"pump mounting screws (secures drain pump to baseplate and clamps to back of ice maker) (5)

• 8/8"small adjustable hose clamp (secures vent to drain pump)

• 7/8"large adjustable hose clamp, (secures drain tube to ice maker bin and drain pump reservoir inlet) (3)

• Rear panel (2)

• Instruction sheet

A. Copper tubing B. Water supply tube clamp

Remove and discard the short, black plastic tube from the

C. Inlet water tube clamp and

supply fine connector

end of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet.

A B C

A. Line to ice maker B. Nut (purchased)

C. Ferrule (purchased) D. Suppfied fine from ice maker

8. Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

If Ice Maker Is Currently Installed

NOTE: If ice maker is not installed, please proceed to "Drain

Pump Installation" section.

1. Push the selector switch to the Off position.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

2. Unplug ice maker or disconnect power.

3. Turn off water supply. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from bin.

4. Unscrew the drain cap from the bottom of the water pan located inside the storage bin. Allow water to drain completely. Replace drain cap. See "Drain Cap" illustration.

Drain Cap

ice Maker Drain Pump Installat on

(on some models)

NOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances. It may be desirable to insulate drain tube thoroughly up to drain inlet to minimize

condensation on the drain tube. Insulated tube kit Part Number W10365792 is available for purchase. Drain pump is designed to

pump water to a maximum height of 10 ft (3 m). Use only Whirlpool approved drain pump kit Part Number 1901A.

Kit Contains:

• Drain pump kit Part Number 1901A

• 8/8"ID x 51/8'' drain tube (ice maker bin to drain pump reservoir inlet)

• 1/2"ID x 10 ft (3 m) drain tube hose (drain pump discharge to household drain)

A. Drain cap

5. If ice maker is built into cabinets, pull ice maker out of the opening.

6. Disconnect water supply line. See "Water Supply Line" illustration.

Water Supply Line Drain Tube

A. ½" adjustable hose clamp

B. Drain tube (ice bin to drain pump)

C. _" adjustable hose clamp D. Drain pump reservoir inlet

A. _" copper tubing B. Cable clamp C. _" compression nut

D. Ferrule (sleeve)

E.Ice maker connection

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during installation.

1. Unplug ice maker or disconnect power.

2. Remove rear panel. See "Rear Panel" illustration for 5 screw locations. Pull rear panel away from the drain tube and

discard.

Rear Panel

A. Screw locations

Remove the old drain tube and clamp attached to the ice maker bin.

NOTE: Discard old drain tube and clamp.

Install new drain tube (%" ID x 51/8'') from ice maker bin to drain pump reservoir inlet using new adjustable clamps. See

"Drain Tube" illustration. NOTES:

• Do not kink.

• Trim tube length, if required.

5. Install vent tube (S/le"ID x 32" [81 cm]) to drain pump reservoir vent. Use one %" small adjustable clamp, supplied. See

"Parts Locations" illustration. NOTE: Do not install household drain tube at this time.

Parts Locations

G F

A. Vent tube B. _" hose clamp

C. Drain pump discharge tube D. Drain pump

6. Remove power cord clamp and ground screw attached to ice maker power cord, which is mounted to the unit base. See

"Parts Locations" illustration. NOTE: Clamp and screw will be reused.

7. Slide drain pump into the ice maker base on the right side. The pump mounting tab should slip into the rectangular slot in the ice maker base. It will be necessary to tip the pump slightly to slip into the slot. See "Drain Pump Mounting Tab

Slot" illustration.

E.Ice maker unit power cord F #8-32 x _" pump mounting screws

G. Drain pump power cord, clamp

and screw

Drain Pump Mounting Tab Slot

A. Mounting tab slot

Drain Pump Installed

/ /

Vent Tube NOTE: Do not pinch, kink or damage the vent tube. Check that it

is not damaged, or pinched or kinked between the cabinet and the ice maker.

A. Vent tube B. Clamps and screws

15. Attach 1/2"ID x 10 ft (3 m) drain tube to pump discharge tube. See "Parts Locations" illustration.

16. Connect ice maker to water supply and install ice maker as specified by the product installation instructions.

17. Check all connections for leaks.

A. Drain pump installed

8. Align the 2 screw holes at the rear of the pump. Use two #8-32 x 3/8"screws, supplied. See "Parts Locations"

illustration.

9. Connect drain tube to ice maker bin outlet (%" ID), using 7/8" adjustable clamp, supplied. See "Drain Tube" illustration.

10. Coil ice maker power cord into a 4" (10.2 cm) diameter coil. Wrap electrical tape around the power cord in several places to keep the cord in a coil. Locate coiled power cord between the drain pump and side of enclosure and plug into the receptacle of the drain pump. See "Parts Locations"

illustration.

11. Attach the drain pump power cord to ice maker unit base with clamp and screw (removed inStep 6) that was used to attach ice maker power cord. See "Parts Locations" illustration.

12. Place new rear panel (small one for 15" ice makers, large one for 18") against the back of the ice maker. Route the vent tube and drain pump discharge tube through cutouts in the rear panel.

13. Secure rear panel with original screws. See "Rear Panel" illustration.

14. Secure vent tube to back of ice maker using 3 clamps and three #8-32 x 3/8"screws, supplied. See "Vent Tube"

illustration.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

18. Plug in ice maker or reconnect power.

19. Turn on ice maker.

20. Wait for rinsing cycle, approximately 5 minutes, to be sure the ice maker is operating properly.

Drain Connect on

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is

provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing back into the ice maker storage bin and potentially flowing onto the floor, causing water damage.

• Drain lines must have a minimum of 5/8"(15.88 mm) inside diameter.

• Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or 1/4"drop per 12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle.

• The floor drains must be large enough to accommodate drainage from all drains.

• The ideal installation has a standpipe with a 1W' (3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain hose and the

standpipe.

IMPORTANT: A drain pump is necessary when a floor drain is not available. A Drain Pump kit, Part Number 1901A, is available for purchase.

Side View

• It may be desirable to insulate the drain line thoroughly up to the drain inlet. An Insulation Sleeve kit, Part Number W10365792, is available for purchase.

Connecting the Drain

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

17/8 ''

(1.9 cm)

I 0" (50.80cm) _ C

" (2.5 cm)

(5 cm - 3.8 cm)

A. Drain hose B. 1" (2.54 cm) air gap

C. PVC drain reducer

D. Center of drain should be 20" (50.8 cm)

from front of door, with or without the 3/4" (1.91 cm) panel on the door. The drain

should also be centered from left to right (81_,, from either side of the ice maker).

Drain Pump System (on some models)

IMPORTANT:

• Connect the ice maker drain to your drain in accordance with the International Plumbing Code and any local codes and ordinances.

• The drain pump discharge line must terminate at an open sited drain.

• Maximum rise 10 ft (3.1 m)

• Maximum run 100 ft (30.5 m)

NOTES:

• If the drain hose becomes twisted and water cannot drain, your ice maker will not work.

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

2. Style 1--For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See "Gravity Drain System."

Style 2--For drain pump system connect the drain pump outlet hose to the drain. See "Drain Pump System."

3. Recheck the ice maker to be sure that it is level. See "Leveling."

4. If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all

water and electrical connections have been made.

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you may need to make several adjustments to level it. You may also use the leveling legs to lower the height of the ice maker for

undercounter installations. Tools Needed

Gather the required tools and parts before starting installation.

• 9" level

• Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another person to assist you.

1. Movetheicemakertoitsfinallocation. NOTE:Ifthisisabuilt-ininstallation,movetheicemakeras

closeaspossibletothefinallocation.

2. Placethelevelontopoftheproducttoseewhethertheice makerislevelfromfronttobackandsidetoside.

3. Pushuponthetopfrontoftheicemaker,andthenlocatethe levelingscrewsthatareonthebottomfrontoftheicemaker.

4. Usinganadjustablewrench,changetheheightofthelegsas follows:

• Turnthelevelinglegtotherighttolowerthatsideofthe

icemaker.

• Turnthelevelinglegtothelefttoraisethatsideoftheice

maker.

NOTE:Theicemakershouldnotwobble.Useshimstoadd stabilitywhenneeded.

5. Pushuponthetoprearoftheicemakerandlocatethe levelinglegsthatareonthebottomrearoftheicemaker.

6. FollowtheinstructionsinStep4tochangetheheightofthe legs.

7. Usetheleveltorechecktheicemakertoseethatitiseven fromfronttobackandsidetoside.Iftheicemakerisnot

level,repeatsteps2to5.Iftheicemakerislevel,gotothe "ConnectWaterSupply"section.

3. The water filter compartment is located in the right-hand side of the ice maker control panel.

4. Attach the filter wrench to the water filter.

Water F Itrat on System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Install the Water Filter

1. Locate the accessory packet in the ice maker and remove the water filter.

2. Take the water filter out of its packaging and remove the cover from the O-rings. Be sure the O-rings are still in place

after the cover is removed.

B D

5. Align the alignment pin on the side of the filter with the cutout notch in the control housing and insert the filter into the

housing.

(

A. Afignment pin B. Unlocked symbol

Turn the filter clockwise until it locks into the housing. Ensure that the alignment arrow on the filter head aligns with the locked symbol on the control box housing.

NOTE: If the filter is not correctly locked into the housing, the ice maker will not produce ice.

A. Afignment arrow aligned with locked symbol

C.Locked symbol

D. Cutout notch incontrol housing

7. Remove the filter wrench.

A. Cover C. Alignment pin

B. O-rings D. Alignment arrow

The Water Filter Status Light Replace the Water Filter

The water filter status lights will help you know when to change your water filter.

• The "Order Filter" status light will be illuminated when it is time to order a replacement filter.

• The "Replace Filter" status light will be illuminated when it is time to replace the filter.

• Replacing the disposable water filter with a new filter will automatically reset the filter status tracking feature. See "Using the Controls."

NOTES:

• "Replace Filter" will remain illuminated if a filter is not

installed.

• The "Filter" status light will flash if the filter is not correctly

installed or there is an obstruction in the water line.

ICE MAKER USE

How Your Ice Maker Works

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice storage bin will monitor the ice levels.

IMPORTANT: If the water supply to the ice maker is turned off, be sure to set the ice maker control to OFR

To purchase a replacement water filter, see "Accessories." Replace the disposable water filter when indicated on the water

filter status display or at least every 9 months. If the ice making rate decreases before the Replace Filter light illuminates, then replace the filter.

1. Locate the water filter compartment in the right-hand side of the control housing. See Step 3 in the "Install Water Filter"

section.

2. Turn the water filter counterclockwise (to the left), and pull it straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling may occur.

3. Install the replacement water filter by following steps 2 through 6 in the "Install the Water Filter" section.

Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

The Ice Making Process

1. Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

Using the Controls

1. To start ice production, press ON/OFR

2. To stop ice maker operation, press ON/OFF.

NOTES:

• Pressing the On/Off button does not shut off power to the ice maker.

• Allow 24 hours to produce the first batch of ice. Discard the first 2 batches produced.

MaxIceMode

Clean

Select the Max Ice feature when you have an upcoming need for a large amount of ice and the ice bin is low or empty. Max Ice mode will produce a greater quantity of ice in a 24-hour period.

• Press MAX ICE while the ice maker is on. The indicator light will illuminate.

• Press MAX ICE again to turn off the Max Ice feature. The indicator light will turn off.

• The Max Ice mode will be on when you first turn on the product. It will turn off after 24 hours. To turn Max Ice back on, press MAX ICE.

Normal Sounds

Your new ice maker may make sounds that are not familiar to you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces such as floors, walls and cabinets can make the sounds

seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them.

• You will hear a buzzing sound when the water valve opens to fill the water pan for each cycle.

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the ice maker can also

make noises.

• The high-efficiency compressor may make a pulsating or high pitched sound.

• Water running over the evaporator plate may make a splashing sound.

It is recommended that you clean the ice maker when the "Cleaning Needed" light is illuminated or 9 months has elapsed or ice production decreases significantly. Toclean your ice maker, see "Ice Maker System" in the "Cleaning" section.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the ice maker door is open for 5 minutes. The alarm will repeat every 2 minutes.

Close the door to turn off. The feature then resets and will reactivate when the door is left open again for 5 minutes.

• Water running from the evaporator plate to the water pan may make a splashing sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.

• You may hear air being forced over the condenser by the condenser fan.

• During the harvest cycle, you may hear a "thud" when the ice sheet slides from the evaporator onto the cutter grid.

• When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

• If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud sound during water filling associated with the flow of water through the inlet valve. Call a licensed, qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

ICE MAKER CARE

C eaning

The ice making system and the air cooled condenser need to be cleaned regularly for the ice maker to operate at peak efficiency and to avoid premature failure of system components. See the "Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water and mild soap or detergent. Wipe and dry. Regular use of a good household appliance cleaner and wax will help maintain the finish. Do not use abrasive cleaners on enamel surfaces as they may scratch the finish.

For products with a stainless steel exterior, use a clean sponge or soft cloth and a mild detergent in warm water. Do not use

abrasive or harsh cleaners. Do not use chlorine bleach on the stainless steel surfaces.

Ice Maker System

Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 15 to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as every 9 months.

NOTE: Use one 16 oz (473 mL) bottle of approved ice maker cleaner. To order, see "Accessories."

1. Press the ON/OFF button.

2. Wait 5 to 10 minutes for the ice to fall into the storage bin. Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan located inside the storage bin as shown. Allow the water to drain completely.

4. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan and you will

have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle before completing the steps below. Use one 16 oz (473 mL) bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle twice with tap water and pour it into the water pan.

A. Water pan B. Drain cap

7. Press the CLEAN button. See "Using the Controls." The Clean button will blink, indicating that the cleaning cycle is in

process. When the "Cleaning Complete" light is illuminated (approximately 70 minutes), the cleaning cycle is complete.

During the cleaning cycle, the system will both clean and rinse itself.

8. After the cleaning cycle is complete, remove the drain cap from the water pan. Look for any cleaning solution left in the

water pan. If cleaning solution drains from the water pan, you should run the clean cycle again. Be sure to refill the water

pan with cleaner before starting the clean cycle again. Be sure to replace the drain cap securely on the water pan. If the

drain cap is loose, water will empty from the water pan and you will have either thin ice or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a fresh quantity of cleaning solution.

9. Press the ON/OFF button to resume ice production.

Condenser

A Dirty or Clogged Condenser

• Obstructs proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures which may lead to component failure.

Pull the bottom forward and then pull down to remove the lower access panel.

A, Lower access panel screws B. Base grille screws

Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

A. Condenser fins

5. Replace the lower access panel using the 4 screws.

6. Plug in ice maker or reconnect power.

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the bin.

3. Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4. Remove the screw from the cutter grid cover.

5. Unplug the wiring harness from the left side of the cutter grid.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

1. Unplug ice maker or disconnect power.

2. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support.

g ii/

A. Cutter grid cover B. Screw

6. Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

A .... D

B_I E

A. Cutter grid harness B. Screw

C. Cutter grid

8. Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan.

9. Disconnect the pump bracket from the water pan and unplug the water pan drain pump.

D. Ice level sensor harness

E Plastic spacer F. Screw

13. Check the following:

• Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

• Hose from water pan is inserted into storage bin drain opening.

14. Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid

harness and the ice level sensor harness.

15. Replace the cutter grid cover using the screw that was removed earlier.

16. Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

17. Plug in ice maker or reconnect power.

18. After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacation and Moving Care

A. Waterpan C.Drain cap

B.Waterpan screw D.Drainpump cover

10. Remove, clean and replace the ice scoop and ice scoop holder.

NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop

holder is located in the lower left of the unit.

• After removing the ice scoop, remove the holder by

removing the 2 screws. NOTE: On some models, remove the holder by lifting up

on the ice scoop holder and then out.

• Wash the ice scoop holder along with the other interior

components using the following instructions.

• Replace the ice scoop holder by replacing the screws or

on some models, pushing in on the holder and then down.

A. Ice scoop holder

11. Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

12. To replace the water pan, set the water pan inside the ice bin. Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the water pan by replacing the mounting screw.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

To Shut Down the Ice Maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support.

Pull forward to remove the lower access panel.

....

jiiiiii/iiiiiiii!!ii[ii_'¸4iiiiiii/iiiiii_'¸ •

................................S

A.Lower access panel screws B.Base grille screws

Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

Replace lower access panel and screws.

Drain water from water pan by removing the drain cap.

If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For Ice Makers with a Drain Pump Installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

• Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the ice maker stand for approximately 5 minutes.

This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water

from the ice bin and the drain pump.

• Unplug ice maker or disconnect power.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Ice Maker Operat on

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet. NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

Failure to follow these instructions can result in death, fire, or electrical shock.

PROBLEM RECOMMENDED SOLUTIONS

Ice Maker Will Not Operate Check that it is plugged into a grounded 3 prong outlet.

Check that the control is turned on. See "Using the Controls." Replace the fuse or reset the circuit breaker.

NOTE: If problems continue, contact an electrician. Room temperature must be above 55°F (13°C). Otherwise, bin thermostat may sense cold room

temperature and shut off even though the bin is not full of ice. The ice maker may not restart once it

does shut off. If there was a large amount of water added to the ice maker, wait a few minutes for the drain pump to

clear. If there is still water in the bin, check to see whether the drain hose is kinked. For models with drain pumps, check that the drain hose is not damaged, or kinked or pinched

between cabinet and ice maker. Use only Whirlpool approved drain pump kit, Part Number 1901A.

Ice Maker Seems Noisy Is the water in the reservoir overflowing? This isnormal. This overflow helps to purge minerals that

were removed from the water during the ice making process.

Is there a "whooshing" sound? Check the following things:

• Check that the water supply is hooked up and turned on.

• Check that the drain cap is tight and the water drain pan pump is securely attached to the water pan.

Is there ice between the evaporator plate and the cutting grid? Check that the ice maker is level. See "Leveling." If the ice maker is level, and the problem persists, run a cleaning cycle. See

"Cleaning." If the ice maker is connected to a water supply pressure in excess of 60 psi, you may hear a loud

sound during water filling associated with the flow of water through the inlet valve. Call a licensed,

qualified plumber to determine the best method to reduce the supply water pressure (50 psi is recommended).

ice Production

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

PROBLEM Ice Maker Runs But

Produces No Ice

Ice Maker Runs But Produces Very Little Ice

KitchenAid KUIS18PNZW0, KUIS18PNZB0, KUIS18NNZW0, KUIS18NNZB0, KUIC18PNZS0 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual