KitchenAid KUDS01FLSS, KUDS01FLBT, KUDS01FLBL, KUDS01DLWH, KUDS01DLSS Dimension Guide

...

1/8 (3.2 mm)

1/8

(3.2 mm)

front

23-3/8

(59.4 cm)

Front View

Side View

3/4

(1.9 cm)

*25-29/32

(65.8 cm)

Drain hose and power supply line should enter through the right side of opening in shaded areas. Drain hose size: 1-1/2" (3.8 cm) Power supply line hole-direct wired: 3/4" (1.9 cm) Power supply line hole-with plug: 1-1/2" (3.8 cm)

Water line should enter through the left side of opening in shaded areas. Minimum 1/2" (12,7 mm) hole.

Undercounter Dishwasher

PRODUCT MODEL SERIES OVERALL DIMENSIONS

CABINET OPENING DIMENSIONS

CUSTOM FRONT PANEL DIMENSIONS

KUDC01TM KUDI01DL KUDI01FL KUDI01IL KUDK01IL KUDL01IL KUDP01DL

KUDP01FL KUDP01IL KUDS01DL KUDS01FL KUDS01IL KUDS01VM

Electrical: 120-volt, 60 Hz, AC-only, 15 or 20 amp electrical supply. Use copper wire only. A time-delay fuse or circuit breaker and separate circuit is recommended.

Water: A hot water line with 20-120 psi (138-862 kPa) water pressure. Water temperature must be minimum 120°F (49°C) at dishwasher. Use 3/8" O.D. copper tubing with compression fitting or flexible stainless steel braided fill line (1/2" minimum plastic tubing is optional but not recommended). Use a 90° elbow with 3/8" N.P.T. external pipe threads on one end to connect to water inlet valve. Do not solder within 6" (15.2 cm) from water inlet valve.

Drain: Use the new drain hose supplied with your dishwasher. If this is not suitable, use a new drain hose with a maximum length of 12 feet (3.7 m) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the drain connector of the dishwasher. Must have a high drain loop 20 inches (50.8 cm) above the subfloor or floor. Connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20 inches (50.8 cm) minimum above the floor. An air gap must be used if the drain hose is connected to house plumbing lower than 20 inches (50.8 cm) above subfloor or floor. Use 1/2" minimum I.D. drain line fittings.

Corner installation: Allow 2" (5,1 cm) minimum between corner wall and dishwasher opening.

Grommet is required for electrical cable or power supply cord hole cut in a metal cabinet.

Do not install dishwasher over carpeted floor. Unit accepts custom door panels.

Top V ented Models

Front Vented Models

3/4" (1.9 cm) insulation – may be compressed (not used on all models)

23-7/8" (60.6 cm)

*For models using a 3/4"

(1.9 cm) custom wood front panel, this dimension is 24-3/4" (62.9 cm).

24-1/2" (62.2 cm)*

21" (53.3 cm)

top vent

model

33-7/8"

(86 cm) min.

with wheels

removed

30-3/16" (76.7 cm)

3/4"

(19.1 mm)

23-1/2" (59.7 cm)

(22.9 cm)

10"

(25.4 cm)

5-1/2"

(14 cm)

6" ***

(15.2 cm)

6" ***

(15.2 cm)

3-1/4"

(8.3 cm)

2-3/4" (7 cm)

34" (86.4 cm) min.*

(5.1 cm)

All surfaces must be free

from intrusions

(5.1 cm)

3-1/4"

(8.3 cm)

3-1/4"

(8.3 cm)

2-3/4" (7 cm)

3-1/4"

(8.3 cm)

24" (61 cm)

min.

24" (61 cm)

*Measured from the lowest point on the underside of countertop.

May be reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.

**Minimum, measured from narrowest point of opening.

***May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. 8531880

07-13-04

24-7/8" (63.2 cm)

3/4" (1.9 cm) insulation – may be compressed (not used on all models)

24-1/2" (62.2 cm)*

front vent

model

21" (53.3 cm)

33-7/8"

(86 cm) min.

with wheels

removed

A custom front panel must weigh no more than 16 pounds and must be made to these dimensions.