KitchenAid KSSC48QMS02, KSSS48QMX02, KSSS48QMW02, KSSS48QMB02, KSSS42QMX01 Installation Guide

...

KJtchen_kid ®

SIDE BY SIDE BUILT-IN REFRIGERATOR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACION REQUIERE DE 20 MAS PERSONAS.

REFRIGERATEUR ENCASTRE COTE A COTE

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L'INSTALLATION NECESSITE L'INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Indice/Table des matieres .................................................................. 2

2309069A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

DESIGN SPECIFICATIONS ............................................................ 4

Product Dimensions ..................................................................... 6

Tipping Radius ............................................................................. 7

Door Swing Dimensions ............................................................... 7

Handle and Door Clearances ....................................................... 8

Classic Series Factory Panels and Kits ..................................... 11

Classic Series Custom Panels ................................................... 11

Overlay Series Custom Panels .................................................. 13

Classic, Architect ®and Pro Line®

Series Custom Side Panels ........................................................ 14

Overlay Series Custom Side Panels .......................................... 14

INSTALLATION REQUIREMENTS .............................................. 15

Tools and Parts .......................................................................... 15

Location Requirements .............................................................. 16

Electrical Requirements ............................................................. 17

Water Supply Requirements ...................................................... 17

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 27

ESPECIFICACIONES DE DISEI_IO .............................................. 28

Medidas del producto ................................................................ 30

Arco de vuelco ........................................................................... 31

Medidas de oscilaci6n de las puertas ....................................... 31

Espacios para la agarradera y la puerta .................................... 32

Paneles y juegos de fabrica de la serie Classic ........................ 35

Paneles a la medida para la serie Classic ................................. 35

Paneles a la medida de la serie Overlay .................................... 37

Paneles laterales a la medida para las

series Classic, Architect ®y Pro Line®...................................... 38

Paneles laterales a la medida para la serie Overlay .................. 38

REQUISITOS DE INSTALACION ................................................. 39

Piezas y Herramientas ............................................................... 39

Requisites de ubicaci6n ............................................................. 40

Requisites electricos .................................................................. 41

Requisitos del suministro de agua ............................................. 41

INSTALLATION INSTRUCTIONS ................................................ 18

Unpack the Refrigerator ............................................................. 18

Reduce Tipping Radius .............................................................. 18

Move the Refrigerator into House .............................................. 19

Install Anti-Tip Boards ................................................................ 19

Connect the Water Supply ......................................................... 19

Plug in Refrigerator ..................................................................... 20

Move Refrigerator to Final Location ........................................... 21

Lower Leveling Legs .................................................................. 21

Install Classic Series Custom Panels ......................................... 21

Install Overlay Series Custom Panels ........................................ 22

Level Refrigerator ....................................................................... 23

Adjust and Remove Doors ......................................................... 23

Install Side Panel ........................................................................ 25

Install Base Grille ........................................................................ 25

Water System Preparation ......................................................... 26

Complete Installation .................................................................. 26

INSTRUCCIONES DE INSTALACION ......................................... 42

C6mo desempacar su refrigerador ............................................ 42

C6mo reducir el arco de vuelco ................................................. 42

C6mo hacer entrar el refrigerador en la casa ............................ 43

C6mo instalar los tableros antivuelco ........................................ 43

Conexi6n del suministro de agua .............................................. 44

C6mo enchufar el refrigerador ................................................... 45

Ubicaci6n final del refrigerador .................................................. 45

Baje las patas niveladoras ......................................................... 45

C6mo instalar los paneles a la medida para la serie Classic ,...45 C6mo instalar los paneles a la medida para la serie Overlay...,46

C6mo nivelar el refrigerador ....................................................... 48

Ajuste y quite las puertas ........................................................... 48

C6mo instalar el panel lateral ..................................................... 49

C6mo instalar la rejilla de la base .............................................. 50

Preparaci6n del sistema de agua .............................................. 50

C6mo terminar la instalaci6n ..................................................... 50

TABLE DES MATIERES

S¢:CURITI:!:DU RI:!:FRIGI:!:RATEUR.............................................. 51

SPI:!:CIFICATIONS DE DESIGN .................................................... 52

Dimensions du produit ............................................................... 54

Rayon de basculement .............................................................. 55

Dimensions pour le pivotement des portes ............................... 55

D_gagements pour les poign_es et portes ............................... 56

Ensembles de panneaux d'origine de la serie Classic .............. 59

Panneaux personnalises de la Serie Classic ............................. 59

Panneaux personnalises de la serie Overlay ............................. 61

Panneaux lateraux personnalises des

Series Classic, Architect ®et Pro Line®..................................... 62

Panneaux lateraux personnalises de la Serie Overlay .............. 63

EXIGENCES D'INSTALLATION ................................................... 64

Outillage et pi_ces necessaires ................................................. 64

Exigences d'emplacement ......................................................... 64

Specifications electriques ......................................................... 65

Specifications de I'alimentation en eau ..................................... 66

INSTRUCTIONS D'INSTALLATION ............................................. 66

Deballage du refrigerateur .......................................................... 66

R_duction du rayon de basculement ......................................... 67

Faire entrer le refrigerateur dans le domicile ............................. 67

Installation de planches antibasculement .................................. 68

Raccordement de la canalisation d'eau .................................... 68

Brancher le refrigerateur ............................................................. 69

Deplacement du refrigerateur a I'emplacement final ................. 69

Deploiement des pieds de nivellement ...................................... 70

Installation des panneaux personnalises de la Serie Classic,...70 Installation des panneaux personnalises de la Serie Overlay ...71

Nivellement du refrig_rateur ....................................................... 72

Ajustement et enlevement des portes ....................................... 73

Installation du panneau lateral ................................................... 74

Installation de la grille de la base ............................................... 74

Preparation du syst_me d'eau ................................................... 75

Achever I'installation .................................................................. 75

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately/

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

DESIGN SPECIFICATIONS

Models - Side by Side Non-Dispensing Refrigerators

Architect ®Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36FMS KSSC42FMS KSSC48FMS

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom panels that are not included.

KSSS36FMB KSSS42FMB KSSS48FMB KSSS36FMX KSSS42FMX KSSS48FMX

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36FMX KSSO42FMX KSSO48FMX

Pro Line ®Series Features extraordinary design and exceptional levels of

performance. This series is a perfect blend of form and function delivering professional quality, durability and simplicity.

KSSV42FMS KSSV42FMM

Models - Side by Side Dispensing Refrigerators

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIlU

Classic Series

Features factory-installed, traditional style trim to provide a "framed" look. This series requires the installation of custom panels that are not included.

KSSS36QMB KSSS42QMB KSSS48QMB KSSS36QMW KSSS42QMW KSSS48QMW KSSS36QMX KSSS42QMX KSSS48QMX

Overlay Series

Features factory-installed, overlay style trim to provide a "frameless" look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36QMB KSSO42QMB KSSO48QMB KSS036QMX KSS042QMX KSS048QMX

Complete Series

Features factory-installed stainless steel trim and panels to create a sleek, contemporary look.

KSSP36QMS KSSP42QMS KSSP48QMS

Side View Top View

• The depth from the front of the top grille to the back of the refrigerator cabinet is 251/8'' (64 cm).

• The power cord is 84" (213 cm) long.

• The water line attached to the back of the refrigerator is 5 ft (1.5 m)long.

• Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

251/8"

(64 cm)

231/2"

(60 cm)

Front View

• Width dimensions were measured from trim edge to trim edge.

.831/8 ''

(211 cm)

84" (213 cm)

Power Cord

Height dimensions are shown with leveling legs extended 1/8" (3 mm) below the rollers.

251/8"

(64 cm)

Model Width A

36 351/4'' (90 cm) 42 411/4" (105 cm) 48 471/4'' (120 cm)

v ==

"31/2'' (9 cm)

*When leveling legs are fully extended to 11/4"(32 mm) below

rollers, add 11/8"(29 mm) to the height dimensions.

.831/8 ''

(211 cm)

(see chart following)

Model Width A (Trim edge to trim edge)

36 361/4'' (92 cm) 42 421/4'' (107 cm) 48 481/4'' (123 cm)

*When leveling legs are fully extended to 11/4"(32 mm) below

rollers, add 11/8"(29 mm) to the height dimensions.

Besurethereisadequateceilingheighttostandtherefrigerator uprightwhenitismovedintoplace.

• Thedollywheelheightmustbeaddedtothetippingradius whenadollyisused.

• Ifneeded,thetippingradiuscanbereduced.See"Reduce TippingRadius."

36 Models

(37 cm)

/ i-

141/2"

40"

(102 cm)

Side Tipping Radius

The side tipping radius varies depending upon the width of the

model. Use the chart provided to determine the side tipping radius.

NOTE: Tip on side only.

_f_ A

Model

36 42 48

Tipping Radius A

901/2'' (229.9 cm) 93" (236.2 cm) 96" (243.8 cm)

F_F_J

111,

(98 cm)l _

42 Models

171/2"

(44 cm)

i10"!

j j130 °

(50 cm)

_-- 193/4"--_ 431/2'.

(110 cm)

The location must permit both doors to open to a minimum of

90°. Allow 41/2'' (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels or custom handles.

To adjust the door swing, see the "Adjust and Remove Doors"

section.

48 Models

431/2"

(110em)

193/4''

(50 cm)

If you are installing custom panels, the panels must allow certain clearances for the handles and for the doors to swing open. First, determine the types of handles you will be using and the door stop setting. Then, choose the appropriate scale drawing to use as a

template for creating the panels.

Door

Classic Handle

Optional Extended

Handle

Custom Panel

......... V4"(6.35 mm)

_/_"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm) 1_/4"(3.2 cm)

1_/_"(3.8 cm) 13/4"(4.4 cm)

2" (5.1 cm)

Architect ® Handle

2V4"(5.7 cm) 2V_"(6.4 cm)

23/4"(7 cm) 3" (7.6 cm)

Handle Dimensions

Actual Size

" 2" 3"

(2.5 cm) (5.1 cm) (7.6 cm)

Overlay Series

Door Swing 90 ° Actual Size

Refrigerator to Cabinetry Clearance

Refrigerator Side Trim

0 Hinge

i I ii I i i I i

, , ---1 .... t-----_.

-÷---4 .... J- 1- i_

i i i i i i i i i i i i

-T .... i .... T-_

1/2"

i I

i i I i i i I i i i I i

i i i

(1.3cm)i

3/4"

(1.9 cm)

(2.5cm)

(3.2 cm)

< 11/2"

-_ .... ÷

i i i

1 1/4"

(3.8cm)

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

11/4"(3.2 cm)

11/2"(3.8 cm)

Spacer Panel

"13

Overlay Series

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator 1" Side Trim (2.5cm)

(6.35 mm)

1/2"

(1.3 cm)

1/4"

3/4"

(1.9 cm)

NOTE: Do not place the door stop screw in the 130° position on Overlay Series models.

See "Adjust and Remove Doors."

Hinge

3/4"(1.9 cm)

1" (2.5 cm)

11/4"(3.2 cm)

1W' (3.8 cm)

1/2" ,

1.3cmi",

Panel

_iii'iiiiii_i!i_!!!i;_!_!i_!ii_:::i!'!ii_i?_i_i:ii_i?_i_iiii!:_ii!_:di:o_:iii!!i,_¸'i!_ii!_i:_;ii!_iii!_i,i__ii!_i_i:_i_,_;:i!iiiii::i:iliii_i_:_!_!_,

All factory parts are available through your KitchenAid dealer or

by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Four kits containing colored acrylic or stainless steel door and

top grille panels are available. Follow the kit instructions for

installing the panels. NOTE: Panel kits are not required for factory-installed stainless

steel panel models.

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (_+)1/16"(1.5 mm) tolerance. Panels that are more than 1/4"(6.35 mm) thick must be routed. If panels are less than 1/4"(6.35 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

Door Panel Part Numbers for Non-dispenser Models

Color 36 42 48

White #2220852 #2220853 #2220854

Black #2220855 #2220856 #2220857

Stainless #2220861 #2220862 #2220863 Steel

Door Panel Part Numbers for Dispenser Models

Color 36 42 48

White #2220864 #2220865 #2220866

Black #2220867 #2220868 #2220869 Stainless #2220873 #2220874 #2220875

Steel

Extended Door Handle Kits

Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles.

Color Part Number

White #4387990 Black #8171418 Stainless Steel #4388062 Matte Aluminum #4387989

The top panel should not weigh more than 10 Ibs (4.5 kg).

__ 71/4''

(184 mm)

Model A

36 35%" (89.5 cm) 42 41%" (105 cm)

48 47%" (120 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 30 Ibs (13.5 kg). The refrigerator panel should not weigh more than 50 Ibs (23 kg).

Model A B

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 16%" (42.6 cm) 223/4'' (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

Door Panels for Dispenser Models

The two freezer panels combined should not weigh more than

30 Ibs (13.5 kg). The refrigerator panel should not weigh more

than 50 Ibs (23 kg).

(1.3cm)

1/2" J Top

rnin.

(6.35 ram) max.

237/16"

59,5 cm)

707/16''

(179 cm)

347/le ''

87,4 cm)

Model A B

36 141/4'' (36.2 cm) 191/4'' (48.9 cm) 42 163/4'' (42.6 cm) 223/4'' (57.8 cm) 48 191/4'' (48.9 cm) 261/4'' (66.7 cm)

Top Grille Panel - Routing Requirements

Top and bottom edges of the top panel should be edge routed

1/2"(1.3 cm) and %" (9.5 mm), respectively. Both ends should be edge routed 7/8"(2.2 cm) as shown.

lJ,,,TL

(6.35 ram)

Top Grille

Grille

I! 1/4"

(6.35 mm)

Center face

detail between i_._

offsets

(9.5ram)

rain. Bottom

Door Panels - Routing Requirements

If an extended handle kit is used, then routing the handle side of the panels is not required. See "Classic Series Factory Panels and Kits" for more information on ordering extended handles.

If the standard handle is used, rout the entire handle side of both panels 31/4'' (8.25 cm) to allow for finger clearance. Then rout the other sides 1" (2.54 cm).

Standard Handle - Top View

31/4"

(8.25 cm)

mln.

Hinge Side

__]

° t

1/4,,(6.35 ram) max. |

[

Door Panel

Panel Door Io

2" (5 cm)

min,

Door Panel - Side View

(2.64cm)

max.

(2.2 cm)

Top J max.

(2.2 cm)

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in

the top grille.

1/2" (1.3 cm)

O-

(}v _i!!_;ii_:iii;_ii!_i_i!!i,_¸':Se_ii7_ii!_!ii;(ii:t_ii!_!ii:_:_7:oiii:i_:_i_7::L_iii:_i!i!_iii_!_!;l

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen decor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a 1/8" (3.18 mm) spacer panel or spacer strips and a 1/4"(6.35 mm) backer panel.

[ Overlay PaheJ Spacer PaheJ 1

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

Spacer Panel

1/8"

Freezer

Dispenser

I i

I_ 1" fninlmutn

I I (2,54 mm)_ ......

i _D00r/GrilleTrim

_ Offset Dimension

Non-Dispenser

-._-_ A _

Freezer

IMPORTANT:

• The weight of the refrigerator door overlay panel cannot exceed 50 Ibs (23 kg).

• The weight of the freezer door overlay panel cannot exceed 30 Ibs (13.5 kg).

• The weight of the top grille overlay panel cannot exceed 10 Ibs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2" (5.08 cm) strips horizontally centered for added support.

NOTE: For the grille and the door panels to be flush, the overlay door panel should be 1/4"(6.35 mm) thicker than the overlay grille panel.

Top Grille

I I

73/8-

(18.73 cm)

8,u,T F ' -

(21.59 em)__

om Offset

1" (2.54 cm)

Refrigerator

_9[- B -}lP,-

Model

I I

I 237/16"

24"

(60.96 cm)

(88.27 cm)

I (59.53 cm)

I I I I

l r__ .... ]

' g_

343/4" /

347/16"

(87,47 cm)

Bettem Offset

Va"(3.2 ram)

Decorative Overlay Panels

14%" (37.15 cm)

171/8'' (43.50 cm)

19%" (49.85 cm)

19%"

(49.85 cm) 231/8''

(58.74 cm) 26%"

(67.63 cm)

Handle-Side

Offset

V_" (3.2 mm)

_ Bottom Offset

Vs" (3,2 ram)

Handle-Side

Offset

Vs" (3.2 mm)

341A '' 36 (87.63 cm)

401A '' 42 (102.87 cm)

461A '' 48 (118.11 cm)

170V2"

(179.07 cm)

_(-- D _

__i

Bottom Offset

Vs" (3.2 mm)

C Model

Handle-Side

Offset -_

1/8" (3.2 ram)

711/16"

(180.50 cm)

147/16"

(36.67 cm)

16Wld'

(43.50 cm)

197/16"

(49.37 cm)

I I I I

m.q{-

701/2'' (179.07 cm)

:_2!..... ....

Bottom Offset

Vs" (3,2 mm)

Backer Panels

197/18'' (49.37 cm)

22Wld' (58.26 cm)

267/18'' (67.15 cm)

341/2'' (87.63 cm)

401/2'' (102.87cm)

461/2'' (118.11 cm)

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type

of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed panel installation

dimensions.

• The side panel should be a minimum of _/2"(1.3 cm) thick to prevent warping.

• Ifthe opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

241/8''

(61.3 cm)

(60.3 cm)

231/2..

(59,7 cm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall. Add %_" (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than V4" (6.35 mm) thick, rout the front edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

Side Trim

1/4"

(6.35 mm)

3/16"

(4,7 mrn) /

Y=" /

(5"5_m) I

1a/a2"(16ram)

(16,7ram)

IV64.

(4,5 turn)

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Rout the front edge of the support board or attach a V4" (6.35 mm) board to hold the panel in the cabinet side trim.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions

and may not reflect the needed installation dimensions.

• The side panel should be a minimum of V_" (12 mm) thick

to prevent warping.

• Ifthe opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

Overlay

(59.40 cm)

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Rout the front edge of the support board or attach a %" (9.5 mm) board to hold the panel in the cabinet side trim.

Side Trim

3/16"

3/8"

(9.7 mm)

1/16"

(1.5 ram)

(3.2 ram) __

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall. Add %2" (0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than %" (9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim.

"<--- (4.5 mm)

INSTALLATION

REQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local

electrical inspector's use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

• Hand drill or electric drill • Torx°_T27 screwdriver (properly grounded)

• Drill bits • rl/s2"nut driver

• Two adjustable wrenches • %" and 1/_,,open-end

wrenches

• Phillips screwdriver • s/=,, Allen wrench

• Small level • s/16"socket wrench

• Appliance dolly • Tape measure

PARTS NEEDED:

• Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

• One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

• Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See "Design Specifications" for more information.

Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See "Design Specifications" for more information.

Pro Line®, Complete and Architect ®Series are shipped complete.

• If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a 1/4"(6.35 mm) compression fitting.

1-CeTORXis a registered trademark of Textron Innovations Inc.

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as gasomine, away from refrigerator.

Faimureto do so can resumt in death, expmosion, or fire.

IMPORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs (272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping Radius."

• Location should permit doors to open fully. See "Door Swing Dimensions."

• Location must permit top grille removal. See "Opening Dimensions."

A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See "Electrical Requirements" for additional information.

The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See "Water Supply Requirements" for more

information.

80" - 90"

(203-229 cm)

843/4'' (215 cm) max. to bottom of solid soffit

min.

77" (196 cm)

Width

(see chart following)

Opening Dimensions

The solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced to prevent tipping during use.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See "Install Anti-Tip Boards" for more information.

NOTE: A clearance of 1/2"(1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

231/2''

(60 ore) rain.

Model Width A (as shown above)

36 351/2'' (90.2 cm) 42 411/2"(105.4 cm)

48 471/2'' (120.7 cm)

E(ectrical Shock Hazard

Pmuginto a grounded 3 prong outleto Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these }nstructione can reeumt }n death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker

box. When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

All installations must meet local plumbing code requirements. The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the right-hand side cabinet must be within 1/2" (12.7 mm) of the rear wall.

If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. A 1/2"(12.7 mm) hole for plumbing should be drilled 6" (15.2 cm) to 12" (30.4 cm) from the right-hand side cabinet or panel. On the floor, the hole should be no more than 11" (28 cm) away from the back wall. On the wall, the hole should be no more than 3" (7.6 cm) up from the floor. See "Connect the Water Supply."

If this recommended water line location is used, no additional plumbing must be purchased.

If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

Do not use a piercing-type or 3/16"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 ram) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

231/2"

(60 cm) min.

(15.2 cm)

INSTALLATION INSTRUCTIONS

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

Classic and Overlay Series

1. Grasp both ends of the top grille.

2. Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

B A B

A. Top grille B. Cabinet side trim

3. Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Architect _ Series

IMPORTANT:

• Do not remove the protective film until the refrigerator is in its operating position.

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1. Remove and save the literature package and parts bag taped to the refrigerator door. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator

bottom. NOTE: Do not remove tape and door bracing until the

refrigerator is in its final position.

2. If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius"

for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to "Move the Refrigerator into

House,"

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius."

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm) 42 881/2'' (224.8 cm) 48 891/4"(226.7 cm)

1. Grasp both ends of the louver panel. Push the louver panel straight up, then pull straight out. Lay the panel on a soft

surface.

2. Grasp both ends of the top grille. Push the top grille straight up, then pull straight out. Lay the top grille on a soft surface.

B A B

A. Topgrille B. Cabinet side trim

C. Louverpanel

3. Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Pro Line _Series

1. Grasp both ends of the top grille.

2. Push the top grille straight up, and then pull straight out.

3. Disconnect the wiring harness from the back of the top grille.

4. Lay the top grille on a soft surface.

5. Remove the six screws that attach each cabinet side trim to

the refrigerator, and remove the side trims.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

1. Place an appliance dolly under the left side of the refrigerator as shown. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect _ Series.

I F

Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

During installation, raise the refrigerator up so there is 1/4" (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the condenser cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 mm) (or longer) wood screws. The wood screws must be screwed into the studs at least 11/2"(3.8 cm). The board(s) must overlap the compressor cover.

A B

ii¸ ...................

....... ° .

2" (5 cm) _

A. Center board _" (6.35 mm) max. above refrigerator

B. Two2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C.Attach to studs with six #8 x 3" (7.6cm) screws D. Compressor cover

2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator. Remove dolly.

4. Do not remove protective film or cover.

5. If necessary, reassemble the trim and top grille after the dolly has been removed from the refrigerator.

IMPORTANT:

• The solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or

one is not available, prevent the refrigerator from tipping during use.

• It is recommended that board(s) be installed before the refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the compressor cover.

Read all directions before you begin. IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a %" hole in the cold water pipe you have selected.

G ...... •.........•.JB

¸I¸I¸I¸¸¸.............................c

F E D

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"drilled hole

in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten

the clamp or the sleeve. This will crush the copper tubing.

8. Before attaching copper tubing to the refrigerator place the free end of the tubing in a container or sink and turn on the

main water supply. Flush at least 2 qt (1.9 L) of water through the copper tubing until water is clear to get rid of any particles

in the water line. Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9. Check for leaks around the saddle valve.

E. Compression sleeve F. Shutoff valve

G. Packing nut

Style 2 - Shutoff Valve Connection

1. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

2. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A.Bulb B.Nut (provided)

3. Turn shutoff valve ON.

4. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

5. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

Connecting to Refrigerator

Style I - Copper Line Connection

1. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

2. A 1/4"x 1/4"coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B

A.Refrigerator water tubing B.Nut (provided)

C.Bulb D. Coupling (provided)

3. Turn shutoff valve ON.

4. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

5. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

E.Ferrule (purchased) F.Nut (purchased)

G. Household water

line

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or eiectdcal shock,

1. Set control switch at top of cabinet to the OFF position.

2. Plug into grounded 3 prong outlet.

]!Yi!ii}_';},_i,<:!_iii:;;iii:e_;iii!:_:_i{i_i},_i?_i_i:;;i!_;i:o_i:_to i_!:_ii:_i_i!ii_ii!!,o,c;i!i_/:iio _s

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

IMPORTANT: To prevent floor damage, make sure levelers are

raised (not touching floor) and refrigerator is on rollers before moving.

1. Move the refrigerator straight back and evenly into the opening. Be sure that water tubing is not kinked and the

power supply cord is on top of the refrigerator next to the cover.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

Door Panels

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Remove the screws that attach the handles to the door frame.

3. Slide the decorative door panels into the door frames.

4. If needed, rout the door panels or install a filler panel between the doors and the decorative panels. See the "Classic Series Custom Panels" section in "Design Specifications."

A .......

}ii,o?ve_i_i_:¸¸i!4!!!s,_',i::!_iiiiiiii_i_{!_!i;iiiiiii,eiiii?ii;

NOTE: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

Use socket wrench to turn leg levelers on both sides of refrigerator to the right (clockwise) until refrigerator weight is supported by leveling legs. The rollers should be off the floor. To avoid cabinet damage, do not apply more than 50 inch-pounds (58 cm - kg) of torque to the leveling legs.

A. Rear leveling legs

B. Front leveling legs

IIIIIIIIl{tllll{lllllllllllll{tlll{{lllllllllllllltllIIttlllll

A. Panels

5. Replace the door handles. Install the top screw on each handle first. Be sure that the top of both door handles are aligned.

6. If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws.

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

A. Top grille

B. Cabinet side trim

Remove one end cap by loosening the nuts and sliding off the end cap.

A. Bottom rail C. End cap B. Nuts D. Top rail

Slide the panel into the top grille channel and reattach the end cap.

A. Panel

Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

Remove the handle side and top trims.

.................yA

A : ......................_

........ _ I11111111111111tllt111111111111ttlit1111111111111tliiiiiiiiiii

A. Trims

Slide the custom panels into the bottom and hinge side trims on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge

side trims.

A. Top grille

B. Cabinet side trim

IMPORTANT:

• Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

In Canada, visit www.KitchenAid.ca, or call

1-800-806-6777.

• Create custom door overlay panels according to the specifications in the "Overlay Series Custom Panels"

section.

• KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and freezer doors.

2. Open the refrigerator and freezer compartment doors.

A .......

IIIIIIIIIltllltllllllllllllllltlilllllllllllllllllltlillllllll

A.Panels

Reinstall the handle-side and top trims.

Remove the protective skin from the screw covers. Snap the screw covers into the handle trim section.

...........A

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A. Top grille

B. Cabinet side trim

Remove one end cap by loosening the nuts and sliding off the end cap.

NOTE: Classic and Overlay Series door panels must be installed before leveling.

1. Open the doors and place the level on top of the refrigerator frame as shown. Check to see whether the refrigerator is level from left to right.

A. Level to check left to right leveling B, Level to check front to back leveling

A. Bottom rail C. End cap B. Nuts D. Toprail

Slide the panel into the top grille channel and reattach the end cap.

A. Panel

Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

Use the leveling bolts to adjust the leveling legs until the refri( erator is level from left to right.

A......................

B--

A. Rear leveling bolt B. Front leveling bolt

3. Place the level(s) on shelf or shelves. Check to see whether the refrigerator is level from front to back.

4. Use the leveling bolts to adjust the leveling legs until the refrigerator is level from front to back.

5. Be sure that all four leveling legs contact the floor and support the full weight of the refrigerator.

6. Make final check to ensure the refrigerator is level.

Door Removal

NOTE: Do not remove the two 1/4"hex-head mounting screws.

A. Top grille

B. Cabinet side trim

A. Torx'_t27 flat-head mounting screws

B. ¼" hex-head mounting screws

1-CeTORXis a registered trademark of Textron Innovations Inc.

+ 53 hidden pages