KitchenAid KSCS25FJSS01 Owner's Manual
CABINET DEPTH
SIDE BY SIDE REFRIGERATOR
Use & Care Guide
For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.kitchenaid.com/canada
RÉFRIGÉRATEUR CÔTE À CÔTE À
PROFONDEUR D’ARMOIRE
Guide d’utilisation et d’entretien
Au Canada, pour assistance, composer l e
Table of Contents/Table des matières...........................................................................2
1-800-461-5681,
www.kitchenaid.com/canada
pour installation ou service le
1-800-807-6777
ou visitez notre site web à
...
2210719
TABLE OF CONTENTS
TABLE DES MATIÈRES
REFRIGERATOR SAFETY.......................................................... 3
INSTALLING YOUR REFRIGERATOR..........................................4
Unpacking Your Refrigerator.......................................................4
Space Requirements....................................................................4
Electrical Requirements...............................................................5
Water System Preparation...........................................................5
Connecting the Refrigerator to a Water Source ..........................6
Custom Door Panels....................................................................7
Base Grille....................................................................................8
Leveling Your Refrigerator ...........................................................8
Understanding Sounds You May Hear........................................9
USING YOUR REFRIGERATOR..................................................10
Ensuring Proper Air Circulation..................................................10
Setting the Controls...................................................................10
Adjusting Control Settings.........................................................11
REFRIGERATOR FEATURES......................................................11
Water and Ice Dispensers..........................................................11
Water Filtration and Monitoring System....................................13
Refrigerator Shelves...................................................................14
Meat Drawer, Crisper and Covers.............................................14
Crisper Humidity Control ...........................................................15
Beverage Drawer........................................................................15
Utility or Egg Bin.........................................................................15
Wine or Can/Bottle Rack ...........................................................15
FREEZER FEATURES..................................................................16
Ice Maker and Storage Bin ........................................................16
Freezer Shelf ..............................................................................16
Freezer Basket ...........................................................................17
DOOR FEATURES........................................................................17
Door Rails...................................................................................17
Door Bins....................................................................................17
CARING FOR YOUR REFRIGERATOR.......................................17
Cleaning Your Refrigerator.........................................................17
Changing the Light Bulbs...........................................................18
Power Interruptions....................................................................19
Vacation and Moving Care.........................................................19
TROUBLESHOOTING..................................................................20
ASSISTANCE OR SERVICE.........................................................23
WARRANTY.............................................................................. 24
WATER FILTER CERTIFICATIONS .........................................25
PRODUCT DATA SHEETS....................................................... 26
SÉCURITÉ DU RÉFRIGÉRATEUR...........................................27
INSTALLATION DU RÉFRIGÉRATEUR ......................................28
Déballage de votre réfrigérateur ................................................28
Espacement requis.....................................................................28
Spécifications électriques..........................................................29
Préparation du système d’eau...................................................29
Raccordement du réfrigérateur à une canalisation d’eau.........30
Panneaux de porte sur commande ...........................................31
Grille de la base..........................................................................32
Nivellement du réfrigérateur.......................................................32
Les bruits de l’appareil que vous pouvez entendre...................33
UTILISATION DU RÉFRIGÉRATEUR..........................................34
Pour s’assurer d’une circulation d’air appropriée......................34
Réglage des commandes..........................................................34
Ajustement du réglage des commandes...................................35
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................35
Distributeurs d’eau et de glaçons..............................................35
Système de filtration et de contrôle d’eau.................................37
Tablettes du réfrigérateur...........................................................38
Tiroir à viande, bac à légumes et couvercles ............................39
Réglage de l’humidité dans les bacs à légumes.......................39
Tiroir à boisson...........................................................................40
Bac utilitaire ou oeufrier .............................................................40
Porte-cannettes/bouteilles ou casier à vin ................................40
CARACTÉRISTIQUES DU CONGÉLATEUR...............................40
Machine à glaçons et bac d’entreposage ................................40
Clayette de congélateur.............................................................41
Panier du congélateur................................................................42
CARACTÉRISTIQUES DE LA PORTE.........................................42
Tringles dans la porte.................................................................42
Compartiments dans la porte ....................................................42
ENTRETIEN DE VOTRE RÉFRIGÉRATEUR...............................43
Nettoyage du réfrigérateur.........................................................43
Remplacement des ampoules d’éclairage................................43
Pannes de courant.....................................................................44
Entretien avant les vacances ou lors d’un déménagement.......44
DÉPANNAGE.................................................................................45
ASSISTANCE OU SERVICE.........................................................49
GARANTIE......................................................................................50
FEUILLES DE DONNÉES SUR LE PRODUIT..........................51
2
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can
WARNING:
precautions:
■
■
■
■
■
■
■
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extensio n cord.
Disco n n e c t po wer before s er v icing.
Replace all panels before operating.
Remove doors from your old refriger a tor.
■
Use nonflammable cleaner.
■
Keep flammable materia ls and vapo r s , such as
gasoline, aw ay from refr iger ato r.
■
Use two or mo re peop le to mov e and install
refrigerator.
■
Disconnect power before installing ice maker (on
ice maker kit ready models only).
■
Use a sturdy glass when dispensing ice or water
(on some models).
SAVE THESE INSTRUCTIONS
ProperDisposalof
Y ourOld Refrigerator
W ARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or
brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before you throw away your old refrigerator or freezer:
■ Take off the doors.
■ Leave the shelves in place so that children may not easily
climb inside.
3
INSTALLING Y OUR
Space Requirements
REFRIGERATOR
Unpacking Y our Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Removing packaging materials
■ Remove tape and any labels from your refrigerator before
using (except the model and serial number label).
To remove any remaining tape or glue, rub the area briskly
with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry .
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see the “Refrigerator Safety” section.
IMPORTANT:
inside your refrigerator, or the Tech Sheet that is fastened to the
base grille.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or “walk” the refrigerator when trying to move
it, as floor damage could occur.
Do not remove any permanent instruction labels
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
72"
(182.9 cm)
36"
(91.5 cm)
20 1/4"
(51.5 cm)
9 1/4"
(23.5 cm)
³⁄₄
in. (184.8 cm).
16 1/2"
(42 cm)
2"
(5 cm)
1 1
13 1/4"
(34 cm)
2
2"(5 cm)
1. Minimum fixed wall position
2. Recommended locations for electrical and water
connections.
3. For full-overlay cabinet doors and a trim kit, the
height of the opening must be 72
12 1/2"
(32 cm)
2 1/2"
(6.5 cm)
Cleaning before use
After you remove all of the packaging material s, clean the inside
of your refrigerator before using it. See the cleani ng instructions
in the “Caring for Your Refrigerator” section.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.
4
■ If you are installing the r ef ri g era t or to fi t f lus h wi th t he front of
the base cabinets, all shoe molding and baseboards must be
removed from the rear of the refrigerator opening.
■ The water hookup and electrical hookup must be placed near
the bottom of the refrigerator.
■ A trim kit is available for those installations where the
refrigerator will not fit flush. See the “Assistance or Service”
section for ordering information.
Do not install the refrigerator near an oven, radiator, or
NOTE:
other heat source, nor in a location where the temperature will fall
below 55°F (13°C) .
Electrical Requirements
W ARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your refrigerator into it s final location, it is
important to make sure you have the proper electrical
connection:
W ater System Preparation
Please read before using the water system.
Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
Turn off the ice maker by opening the freezer door and lifting
1.
up the wire shut-off arm as shown.
Flush the water system by dispensing and discarding
2.
2 to 3 gallons (appr oxima tely 6 to 7 m inute s) of wa ter thr o ugh
the dispenser. This will clean the system and help clear air
from the lines. Additional flushing may be required in some
households.
Turn on the ice maker by opening the freezer door and
3.
lowering the wire shut-off arm as shown. Allow 24 hours to
produce the first batch of ice. Discard the first three batches
of ice produced. Ice maker should then p roduce
approximat el y 7 to 9 batche s o f ice in a 24-hou r per iod.
Recommended gr oun ding met hod
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be tur ned off by a switch. Do not use an
extension cord.
Before performing any type of installation, cleaning, or
NOTE:
removing a light bulb, turn the control, (Thermostat, Refriger ator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
5
Connectingthe Refrigerator
to a Water Source
Read all directions carefully before you begin.
IMPORTANT:
In order to prevent possible leakage resulting in property
damage, be sure to observe the following:
■ If operating the refrigerator before installing the water
connection, turn ice maker to th e OFF position to prevent
operation without water.
■ All installations must be in accordance with local plumbing
code requirements.
■ Use the water tubing provided and check for leaks.
■ Install water tubin g only in areas where temperatures will
remain above freezing.
REMEMBER:
begin producing ice.
Tools required:
■ Standard screwdriver
■ ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable
wrenches
■ ¹⁄₄ in. drill bit
■ Hand drill or electric drill (properly grounded )
NOTE:
¹⁄₄ in. saddle-type shut-off valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Cold Water Supply
The ice maker water valve contains a flow washer which is used
as a water pressure regulator. The ice maker needs to be
connected to a cold water line with water pressure between 30
and 120 psi. If a problem occurs, call your utility company.
Connecting to water line:
Unplug refrigerator or disconnect power.
1.
Turn OFF main water supply. Turn ON nearest faucet long
2.
enough to clear line of water.
Find a
3.
water pipe near the refrigerator.
NOTE:
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
It may take up to 24 hours for your ice maker to
Your refrigerator dealer has a kit available with a
³⁄₁₆ in.
¹⁄₂ in. (12.70 mm) to 1¹⁄₄ in. (3.18 cm) vertical COLD
Horizontal pipe will work, but the following procedure
4.
Route
in. (6.35 mm) copper tubing from the water pipe to
¹⁄₄
the lower rear corner of the refrigerator location. Be sure both
ends of copper tubing are cut square.
Turn OFF main water supply. Turn ON nearest faucet long
5.
enough to clear the line of water.
Using a groun de d dril l, d r ill a
6.
¹⁄₄ in. (6.35 mm) hole in the cold
water pipe you have selected.
1. Cold Water Pipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
5. Compression Sleeve
6. Shut-Off Valve
7. Packing Nut
Fasten shut-off valve to cold water pipe with pipe clamp. Be
7.
sure outlet end is solidly in the
¹⁄₄ in. (6.35 mm) drilled hole in
the water pipe and that washer is under the pipe clamp.
Tighten packing nut. Tighten the pipe clamp screws carefully
and evenly so washer makes a watertight seal. Do not
overtighten or you may crush the copper tubing, especially i f
soft (coiled) copper tubing is used. Now you are ready to
connect the copper tubing.
Slip compression sleeve and compression n ut on copper
8.
tubing as shown in the diagram. Insert the end of the tubing
into the outlet end of the shutoff valve as far as it will go.
Screw the compression nut onto the outlet end with an
adjustable wrench. Do not overtighten.
Place the free end of the tubing into a container or sink, and
9.
turn ON main water supply and flush out tubing until water is
clear. Turn OFF the shut-off valve on the water pipe.
Slip the compression sleeve and compression nut onto the
10.
other end of the copper tube. Insert into the tube coupling as
far as it will go. Screw compression nut on to coupling and
tighten with wrenches. Do not overtighten.
Add strain relief to hold coupling in position.
11.
6
Connecting to refrigerator:
1. Remove the shipping tape from gray, coiled water tubing on
the rear of the refrigerator.
2. Style 1: Thread the provided nut onto the coupling on the end
of the copper tubing. Tight en th e nut by ha nd. Then tighten i t
with a wrench two more turns. Do not overtighten.
Weight requirements for raised panel inserts:
■ Refrigerator door panel should not exceed 28 lbs.
(12.7 kg).
■ Freezer door panels should not exceed 21 lbs. (9.5 kg)
combined weight.
Dimensions for custom wood panels:
1/8"
(3.18 mm)
1/8"
(3.18 mm)
Style 2: Thread the provided nut onto the water valve as
shown.
Tighten the nut by hand. Then tighten it with a wrench two
more turns. Do not overtighten.
3. Turn shut-off valve ON. Check for leaks. Tighten any nuts
or connections (including connections at the valve) that leak.
4. Plug in refrigerator or reconnect power.
5. Flush the water system (s ee the “Water System Preparation”
section).
NOTE: It may take up to 24 hours for your ice maker to begin
producing ice.
Custom Door Panels
Creating Custom Wood Panels
If you plan to install c ustom wood de corator p anels, y ou will need
to create the panels yourself or consult your cabinet maker or
carpenter. See dimensional drawings for wood panel inserts.
Flat panels:
You can create a custom flat panel a maximum of ¹⁄₄ in. (6.35 mm)
thick to replace your decorator panels. Flat wood panels less
than ¹⁄₄ in. (6.35 mm) thick are not recommended.
Raised panels:
A raised panel design can be created by screwing or gluing wood
panels to ¹⁄₄ in. (6.35 mm) backing or by using ³⁄₄ in. (19.05 mm)
stock with routed edges. Raised panels should be spaced
2¹⁄₄ in. (5.70 cm) from the back edge of the handle to allow room
for fingers to grasp the handle.
1/8"
(3.18 mm)
15 3/8"
(39 cm)
15 3/8"
(39 cm)
24 3/16"
(61.5 cm)
68 15/32"
(174 cm)
29 7/8"
(76 cm)
19 3/32"
(48.5 cm)
1/8"
(3.18 mm)
Installing Custom Wood Panels
1. Remove any packing tape.
2. Remove the refrigerator and freezer door trims from the hinge
side of each door by pulling the trim away from the bottom of
the door first.
3. Partially unscrew the two screws that hold the top trim in
place. It is not necessary to completely remove the screws.
Loosen the screws approximately ¹⁄₄ in. (6.35 mm) from the
trim to allow the panels to slide freely.
4. Remove the existing door panels, if panels were provided.
5. Slide custom door panels into place.
NOTE: The freezer door panels may require ¹⁄₈ in. (3.18 mm)
cardboard fillers behind the panels to keep them from being
loose in that area.
7
6. Replace the hinge side trims by inserting the notched end
under the top trim first.
7. Tighten the two top trim screws.
1. Side Trims
2. Top Trim Screws
3. Door Panels
4. Filler Panels
To replace the base grille:
1. Open the refrigerator and freezer doors to 90°.
2. Place the lower clips in the openings in the metal panel.
3. Roll the grille up toward the refrigerator until it snaps into
place.
Leveling Y our Refrigerator
Your refrigerator has a front and rear roller at the base of the
product on each side. All four rollers can be adjusted from the
front of the product. If your refrigerator seems unsteady or you
want the doors to close easier, adjust the refrigerator's tilt using
the instructions below:
1. Check the installation location to be sure that you have the
proper clearance for the refrigerator. (See the “Space
Requirements” section.)
2. Plug into a grounded 3 prong out let.
3. Move the refrigerator into its final po sition.
4. Open the refrigerator and freezer doors to locate the leveling
bolts at the left and right of the refrigerator base. If your
refrigerator has a base grille, remove it (see “Base Grille”
earlier in this section).
NOTE: The top bolt will adjust the rear of the refrigerator, and
the bottom bolt will adjust the front of the refrigerator.
Base Grille
Style 1:
To remove the base grille:
1. Open the refrigerator and freezer doors 90°.
2. Remove screws from the base grille using a Phillips
screwdriver .
Note: Do Not Remove Tech Sheet that is fastened behind the
base grille.
To replace the base grille:
1. Open the refrigerator and freezer doors to 90°.
2. Position the base grille in front of the refrigerator and replace
the screws.
Style 2:
To remove the base grille:
1. Open the refrigerator and freezer doors to 90°.
2. Grasp the grille with both hands.
3. Lift up and tilt the top of the grille toward you.
NOTE: Do not remove the Tech Sheet that is fastened behind the
grille.
1. Rear Leveling Bolt
2. Front Leveling Bolt
5. Use a ¹⁄₂ in. (12.70 mm) socket wrench to adjust the leveling
bolts. Turn the leveling b olt to the right to rais e that side of the
refrigerator or tu rn the leveling bolt to the left to lower that
side. It may take several turns of the leveling bolts to adjust
the tilt of the refrig e ra to r.
NOTE: Be careful not to unscrew the lev eling bolts too much
when lowering the refrigerator. The bolt head will start to
come away from the refrigerator when in the lowest position.
If the screw does come out of the rear roller bracket, the
compartment access cover on the back of the refrigerator will
have to be removed to reinstall the bolt.
8
6. Adjust the front leveling bolt to bring the refrigerator top
parallel with the cabinet above the refrigerator. Leave
approximately ¹⁄₈ in. (3.18 mm) gap between the top hinges
and the cabinet. If you do not have a cabinet above the
refrigerator, simply adjust the refrigerator to make it level.
Style 1
1. Leave
2. Front of the refrigerator
in. (3.18 mm) minimum clearance for
¹⁄₈
leveling the refrigerator. Leave
minimum clearance if you have full-overlay cabinet
doors.
in. (6.35 mm)
¹⁄₄
Style 2
1. Leave
2. Front of the refrigerator
in. (19.05 mm) minimum clearance
³⁄₄
between a full-overlay cabinet door and a
refrigerator with a trim kit.
7. Adjust the rear leveling bolt to bring the refrigerator level with
the side cabinets or cabinet end panels.
8. If you want, you may now use the four leveling bolts to raise
the refrigerator to close the gap betw een the refrigerator top
hinge and the cabinet opening. Check that all four rollers still
touch the floor and that the cab inet doors above the
refrigerator open all the way.
NOTE: Cabinets with full-ove rlay do ors wi ll r equir e ¹⁄₄ in. (6.35
mm) additional clearance between the top hinge and cabinet
to prevent the doors from hitting the hinge when opening. If
you have a trim panel kit on the refrigerator doors, ³⁄₄ in.
(19.05 mm) additional clearance is needed to prevent the
cabinet doors from hitting the refrigerator door trim.
9. Replace the base grille.
UnderstandingSounds Y ouMay Hear
Your new refrigerator may make sounds that your old one didn’t
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, like the floor, walls, and cabinets, can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds and what may be making them.
■ If your product is equipped with an ice make r, you will hear a
buzzing sound when the water valve opens to fill the ice
maker for each cycle.
■ The defrost timer will click when the automatic defrost cycle
begins and ends. Also, the Thermostat Control (or
Refrigerator Control depending on the model) will click when
cycling on and off.
■ Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
■ Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperature. The high
efficiency compressor may cause your new refrigerator to run
longer than your old one, and you may hear a pulsating or
high-pitched sound.
■ Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
■ You may hear the evaporator fan motor circulating the air
through the refrigerator and freezer compartments.
■ As each cycle ends, you may hear a gu rgling sound due to
the refrigerant flowing in your refrigerator.
■ Contraction and expansion of the inside walls may cause a
popping noise.
■ You may hear air being forced over the condenser by the
condenser fan.
■ You may hear water running into the drain pan during the
defrost cycle.
9
USING YOUR
REFRIGERATOR
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit
airflow between the two sections. Cold air enters the bottom of
the freezer section and moves up. It then enters the refrigerator
section through the top vent. Air then returns to the freezer as
shown.
Setting the Controls
Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food into
the refrigerator.
IMPORTANT: If you add food before the refrigerator has cooled
completely, your food may spoil. Turning the Refrigerator and
Freezer Controls to a cooler than recommended setting will not
cool the compartments any faster.
Warmer
Water
Filter
Warmer
Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be prevented and
the temperature controls will not function properly.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer from food, wrap or cover foods tightly.
Checking Airflow
To measure the amount of cold air being directed from the freezer
compartment into the refrigerator section, hold your hand in front
of the top vent. You can adjust the control to feel the different
amounts of airflow.
For further information on temperatures inside your refrigerator,
refer to the “Troubleshooting” section.
Cooler
Power
On/Off
Freezer
The Refrigerator Control adjusts the refrigerator
compartment temperature. Press the up arrow to make the
temperature warmer. Press the down arrow to make the
temperature colder.
The Freezer Control adjusts the freezer compartment
temperature. Press the up arrow to make the temperature
warmer. Press the down arrow to make the temperature colder.
The Power Control turns off the refrigerator’s temperature
control. Press the Power Control button.
NOTE: Your product will not cool when the Power Cont rol is set
to OFF.
The Automatic Exterior Moisture control continuously guards
against moisture buildup on the outside of your refrigerator
cabinet. This control does not have to be set or adjusted.
Cooler
Refrigerator
10
Adjusting Control Settings
Give the re fr ige r a tor ti me to co ol down completely before add ing
food. It is best to wait 24 hours before you put food into the
refrigerator. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
If you need to adjust temperatures in the refrigerator or freezer,
use the setting s listed in the chart below as a g u id e. Wait at least
24 hours between adjustments.
CONDITION/REASON: RECOMMENDED
ADJUSTMENT:
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models.
If you are interested in purchasing one of the accessories please
call the toll-free number on the cover or in the “Assistance or
Service” section.
REFRIGERATOR section
too warm
■ Door opened often
■ Large amount of food added
■ Room temperature very warm
FREEZER section too warm/ice
not made fast enough
■ Door opened often
■ Large amount of food added
■ Very cold room temperature
(can’t cycle often enough)
■ Heavy ice usage
■ Air diffuser blocked by items
REFRIGERATOR section
too cold
■ Controls no t set c orre ctly fo r your
conditions
FREEZER sect ion too cold
■ Controls no t set c orre ctly fo r your
conditions
Press the
REFRIGERATOR
Control arrow down
to the next lower
number
Press the FREEZER
Control arrow down
to the next lower
number
Move packages out
of airstream
Press the
REFRIGERATOR
Control arrow up to
the next higher
number
Turn FREEZER
Control arrow up to
the next higher
number
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.
W ater and Ice Dispensers
(on some models)
WARNING
Cut Hazard
Use a sturdy glass when dispensing ice or water.
Failure to do so can result in cuts.
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, or a
lock option to avoid accidental dispensing.
The ice di sp ense r
Ice dispenses from the ice maker storage bin in the freezer. When
the dispenser lever is pressed:
■ A trap door opens in a chute betw een the dispenser and the
ice bin.
■ Ice moves from the bin and falls through the chute.
■ When you release the dispenser lever, the trap door closes
and the ice dispensing stops. The dispensing system will not
operate when the freezer door is open.
11
Some models dispense both cubed and crushed ice. Before
DISPENSER
LOCK
UNLOCK
dispensing ice, select which type of ice you prefer. The button
controls are designed for easy use and cleaning.
■ For cubed ice, press the CUBE button until the red indicator
appears in the window above the CUBE button.
ICE
CRUSH CUBE
■ For crushed ice, press the CRUSH button until the red
indicator appears in th e window above the CRUSH button.
For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in size.
When changing from CRUSH to CUBE, a few ounces of crushed
ice will be dispensed along with the first cubes.
To dispense ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the i c e dispenser lever. Hold the
glass close to the dispenser open ing so ice does not fall
outside of the glass.
To dispense water:
1. Press a glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
NOTE: Dispense enough water every week to maintain a fresh
supply.
The dispenser light
The dispenser area has a light. It can be turned on manually by
pressing the ON button at the right hand side of the control
panel. The red indicator above the ON button will appear. On
some models: Whenever you use the dispenser the lev er wi ll
automatically turn the light on.
LIGHT
OFF ON
IMPORTANT: You do not need to apply a lot of pressure to
the lever in order to activate th e ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: The first few batches of ice may have an off-flavor
from new plu m bi ng an d par t s. T h r o w the ice away. A ls o , ta ke
large amounts of ice from the ice bin, not through the
dispenser.
The water dispenser
When the refrigerator is first hooked up, press the water
dispenser bar with a glass or jar until you draw and discard 2 to 3
quarts (1.9 to 2.8 L). I t wil l ta ke th re e to four mi nutes for th e wa ter
to begin dispensing. The wa ter you draw and discard rinses the
pipes.
Allow several hours for the refrigerator to cool down and chill
water.
IMPORTANT: Depending on your model, the small removable
tray at the bottom of the dispenser is designed to catch small
spills and allow for easy cleaning. There is no drain in the tray.
The tray can be removed from the dispenser and carried to the
sink to be emptied or cleaned.
NOTE: See the “Changing the Light Bulbs” section for
information on changing the dispenser light bulb.
On models without crushed ice, the light switch is a rocker-style
type. Push the switch to turn the light on, and push again to turn
the light off.
The dispenser lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent
accidental dispensing by small children and pets. To turn off the
dispenser, press the LOCK button. The indicator will appea r
above the LOCK button and the ice and water dispensers will not
work. To unlock the dispenser, press the UNLOCK button until
the indicator appears. Then continue to dispense ice or water as
usual.
NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates
the dispenser levers.
12
W ater Filtration and Monitoring System
(on some models)
The water filter indicator light
The water filter indicator light will help you know when to chan g e
your water filter cartridge. The light is located at the top of the
refrigerator compartment. The light will change from green to
yellow. This tells you that it is almost time to change the water
filter cartridge (90% of the filter life has be en used). It is
recommended that you replace the water filter cartridge when the
water filter indicator light changes to red OR water flow to your
water dispenser or ice maker decreases noticeably. (See
“Changing a water filter cartrid ge” later in this section.)
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system.
Take the new cartridge out of its packaging and remove
3.
protective cover from o-rings.
Slide the cartridge cap onto the new cartridge as shown in
4.
Step 2.
With cartridge cap in th e vertical position, push the new f ilter
5.
cartridge into th e base gri lle until it stops. Rot ate the ca rtridge
cap clockwise to a horizontal pos ition.
Warmer
Cooler
Refrigerator
Water
Filter
Power
On/Off
Warmer
Cooler
Freezer
After changing the water filter cartridge, reset the water filter
indicator light b y pre ssing th e W ATER FILTER button 5 times. Th e
indicator light will change from red to green when the system is
reset.
Changing a water filter cartridge
The water filter is located be low the freezer compartment door.
Locate the water filter cartridge cap in the front base grille
1.
below the freezer compartment door. Rotate the cap
counterclockwise to a vertical position and pull the cap and
filter cartridge out through the base grille.
There will be water in the cartridge. Some spilling may
NOTE:
occur .
RUN WATER THROUGH THE DISPENSER UNTIL THE
6.
WATER RUNS CLEAR (about 2-3 gallons or 6-7 minutes).
This will clean the syst em and clear air from the lines.
Additional flushing may be required in some households.
As air is cleared from the system, water may spurt out
NOTE:
of the dispenser.
Using the dispenser without the water filter
You can ru n the dispenser without a water filter cartridge. Your
water will not be filtered. If you run the dispenser without a water
filter cartridge, keep the cartri dge cap and replace it in the base
grille for future use.
Remove the water filter cartridge (See “Changing a water
1.
filter cartridge” earlier in this section.) Then slide the cartridge
cap off the end of the filter cartridge. DO NOT DISCARD THE
CAP.
With the cartridge cap in the vertical position, insert the cap
2.
into the base grille until it stops.
Remove the cartridge cap by sliding it off the end of the old
2.
cartridge. The cap will slid e to the left or right. DO NOT
DISCARD THE CAP.
Rotate the cartridge cap to a horizontal position as shown in
3.
Step 5. (See “Changing a water filter cartridge” earlier in this
section.)
The cartridge cap may not be even with the base
NOTE:
grille.
Ordering replacement filters
To order more water filter cartridges, see the “Assistance or
Service” section.
13
Refrigerator Shelves
The shelves in your refrigerat or are adjustable to meet your
individual storage need s. Your model may have glass or wire
shelves.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It wil l also reduce the
amount of time the refrigerator door is open, and save energy.
Slide-out Shelves (on some models)
■ To slide out shelf, carefully pull front of shelf toward you.
■ To slide in shelf, push shelf in until it stops.
To remove and replace a shelf in a metal frame:
Pull the shelf forward to the stop.
1.
Tilt front of the shelf up and lift it slightly as you pull the shelf
2.
from the frame.
Replace the shelf by guiding it back into the slots on the
3.
frame and pushing the shelf in past the stop.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
Remove the sh elf/f rame b y tiltin g it up at the fro nt and lifting i t
1.
out of the shelf supports.
Replace the shelf/frame buy guiding the rear shelf hooks into
2.
the shelf supports. Tilt the front of the shelf up until the rear
shelf hooks drop into the shelf supports.
Lower the front of the shelf and check to make sure that the
3.
shelf is securely in position.
Fixed Shelves (on some models)
To remove and replace the shelf in a fixed metal frame:
Remove the shelf by pushing up on the front of the shelf until
1.
it snaps free.
Slide the shelf forward and lift up.
2.
Replace the shelf by positioning the sides of the shelf over
3.
the frame.
Slide the shelf back until the rear hooks are securely in place.
4.
Snap the front of the shelf to the frame.
Meat Drawer , Crisper and Covers
To remove and replace the meat drawer and crisper:
Slide the meat drawer or crisper straight out to the stop. Lift
1.
the front of the drawer with one hand while supporting the
bottom of the drawer with your other hand and slide the
drawer out the rest of the way.
Replace the meat drawer or crisper by sliding it back in fully
2.
past the drawer stop.
LOW
HIGH
To remove and replace the meat drawer or crisper covers:
Remove the meat drawer or crisper. Press up in center of
1.
crisper glass insert until it rises above the plastic frame.
Holding the crisper glass firmly, carefully slide the glass insert
forward to remove.
Lift crisper cover frame up and remove. Repeat steps to
2.
remove the meat drawer cover.
14
Meat storage guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish .................use same day as purchased
Chicken, ground beef, variety meat (liver, etc.).........1-2 days
Cold cuts, steaks/roasts...........................................3-5 days
Cured meats...........................................................7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
Crisper Humidity Control
(on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
■
LOW (open)
of fruits and vegetables with skins.
Fruit:
crisper. Do not wash or hull berries until the y ar e re ady to u se.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins:
container and store in crisper.
■
HIGH (closed)
of fresh, leafy vegetables.
Leafy vegetables:
off bruised and discolored areas. Place i n plastic bag or
plastic container and store in crisper.
Humidity control location:
■ Humidity Control on crisper drawer (Style 1 - on left)
■ Humidity Control on crisper cover (Style 2 - on right.
lets moist air out of the crisper for best storage
Wash, let dry and store in refrigerator in plastic bag or
Place in plastic bags or plastic
keeps moist air in the crisper for bes t storage
Wash in cold water, drain and trim or tear
To remove and replace the beverage drawer shield:
Remove the beverage drawer shield by grasping it at the
1.
bottom center. Pull up in the center while turning the shield
slightly to one side.
Replace the shield by grasping it at the bottom center and
2.
inserting one side into the beverage drawer cover.
Carefully b e nd th e shield at the center to ins ert t he o t he r s id e
3.
into the cover.
Utility or Egg Bin
(on some models - Accessory)
Depending on your model, y ou may ha ve a one piec e utility b in or
a three piece egg bin. To use the three piece egg bin, remove the
cover and place the eggs in the egg tray. Replace cover and store
on an interior refrigerator shelf. If you prefer, you can remove the
egg tray and place the entire carton of eggs i n the bin. Replace
the cover.
NOTE: Eggs should be stored in a covered container. If your
model does not have an egg bin or covered utility bin, store
eggs in their original container on an interior shelf.
Beverage Drawer
To remove and replace the beverage drawer:
Remove the beverage drawer by sliding it straight out to the
1.
stop. Lift up at the front and slide the beverage drawer out
the rest of the way.
Replace the beverage drawer by sliding it back in fully past
2.
the stop.
Wine or Can/Bottle Rack
(on some models -Accessory)
To remove and replace the wine rack (left) or can/bottle rack
(right):
Remove the rack by pulling it straight out from the shelf.
1.
Replace the rack by sliding it in between the shelf and the
2.
wall of the refrigerator.
15
FREEZER FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in t he “Assistance or
Service” section
Ice Maker and Storage Bin
(on some models - Accessory)
To turn the ice maker on:
The on/off switch for the ice maker is a wire shut-off arm located
on the side of the ice maker. To turn the ice maker on, simply
lower the wire shut-off arm.
NOTE: The ice maker will not make ice until the freezer is cold
enough. Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced.
To turn the ice maker off:
■ Automatic turn off: As ice is made, the ice cubes will fill the
ice storage bin. The ice cubes will raise the wire shut-off arm
to the OFF (arm up) position.
■ Manual turn off: Lift the wi re shut-off arm to the OFF (arm up)
position and listen for the click to make sure the ice maker
will not continue to operate.
To remove and replace the ice bin:
1. Pull the covering panel out from the bottom and then slide it
back toward the rear.
2. Lift the wire shut-off arm so it clicks into the OFF (arm up)
position. Ice can still be dispensed, but no more can be
made.
3. Lift up the front of the storage bin and pull it out.
4. Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shut-off arm down to the ON
position to restart ice production. Make sure the door is
closed tightly.
To care for ice storage bin or bucket:
1. Empty the ice container. Use warm water to melt the ice if
necessary. Never use anything sharp to break up the ice in
the bin or bucket. This can cause damage to the ice container
and the dispenser mechanism.
2. W ash with a mild de tergent, rinse well and dry thorou ghly. Do
not use harsh or abrasive cleaners or solvents.
REMEMBER:
■ Allow 24 hours to produce the first batch of ice.
■ Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.
■ The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.
■ Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintain ed.
■ It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
■ Do not force the wire shut-off arm up or down.
■ Do not store anything on top of the ice maker or in the ice
storage bin.
Freezer Shelf
To remove and replace the shelf:
1. Remove the shelf by lifting it up and pulling it straight out.
2. Replace the she lf by p utting it over the sup ports a nd low ering
it into place.
Frozen food storage guide
Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Ice crystals inside
a sealed package are normal. This simply means that moisture in
the food and air inside the package have condensed, creating ice
crystals.
Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2-3 lb of food per cubic foot [907-1,350 g
per L] of freezer space). Leave enough space in the freezer for air
to circulate around packages. Be careful to leave enough room
for the door to close tightly.
For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.
16
Loading...