KitchenAid KRFF300EBS User Manual
REFRIGERATOR USER INSTRUCTIONS
THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.kitchenaid.com for additional information. If you still need assistance, call us at 1-800-422-1230.
In Canada, visit our website at www.kitchenaid.ca or call us at 1-800-807-6777.
You will need your model and serial number, located on the inside wall of t
Para obtener acceso a “Instrucciones para el usuario del refrigerador” en español, o para obtener información adicional acerca de
su producto, visite: www.kitchenaid.com.
Necesitará su número de modelo y de serie, ubicado en el interior del compartimiento del refrigerador.
Table of Contents / Table des matières
REFRIGERATOR SAFETY.....................................................................2
Proper Disposal of Your Old Refrigerator...........................................2
INSTALLATION INSTRUCTIONS .........................................................3
Unpack the Refrigerator..................................................................
Location Requirements....................................................................... 3
Remove and Replace Refrigerator Doors and Drawer Front.............4
Electrical Requirements ..........................
Water Supply Requirements...............................
Connect the Water Supply..................................................................6
Handle Installation and Removal........................................................8
Door Closing and Door Alignment......................................................9
FILTERS AND ACCESSORIES .............................................................9
Water Fi
ltration System....................................................................... 9
Install Air Filter...................................................................................10
Install Produce Preserver..................................................................10
Accessories..............................................................................
REFRIGERATOR USE ..
Opening and Closing Doors..............................................................11
Using the Controls............................................................................12
Water Dispenser................................................................................13
Ice Maker...........................................................................................13
REFRIGERATOR FEATURES ..................
Refrigerator Shelves..........................................................................14
Pantry Drawer ...................................................................................14
Crisper...............................................................................................15
DOOR FEATURES ............................................
Condiment Bins.................................................................................15
Fresh Bin.................
Half-Height Bin..................................................................................16
REFRIGERATOR CARE................................................
Cleaning ............................................................................................16
Changing the Light Bulbs .................................................................16
Vacation and Moving Care...............................................................17
TROUBLESHOOTING..........................................................................18
WATER FILTER CERTIFICATIONS ....................................................23
PERFORMANC
WARRANTY..........................................................................................25
.......................................................................11
..........................................................................15
E DATA SHEET..........................................................24
............................................ 6
................................6
...........................................14
...................................15
.......................16
....3
.........11
SÉCURITÉ DU RÉFRIGÉRATEUR .....................................................26
Mise au rebut adéquate de votre vieux réfrigérateur..........
INSTRUCTIONS D’INSTALLATION ...............................................
Déballage du réfrigérateur.................................................................27
Exigences d'emplacement .............................................
Retrait et réinstallation des portes du
réfrigérateur et de l'avant du tiroir ....................................................28
Spécifications électriques................................................................. 31
Spécifications de l’alimentation en eau............................................31
Racco
Installation et démontage des poignées..........................................33
Fermeture et alignement de la porte................................................34
FILTRES ET ACCESSOIRES............................................................... 35
Système de filt
Installation du filtre à air....................................................................35
Installation du conservateur pour produits frais............................... 36
Accessoires.......................................................................................37
UTILISATION DU RÉFRIGÉRATEUR................................................. 37
Ouverture et fermeture des
Utilisation des commandes ..............................................................37
Distributeur d'eau ............................................................................. 39
Machine à glaçons............................................................................ 40
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ..........................
Ta
Garde-manger...................................................................................41
Bac à légumes.................................................................................. 41
CARACTÉRISTIQUES DE LA PORTE................................................42
Balconnets à condiments....
Balconnet fraîcheur........................................................................... 42
Balconnet mi-hauteur ....................................................................... 42
ENTRETIEN DU RÉFRIGÉRATEUR ...................................................42
Nettoyage............................................................
Remplacement des ampoules d’éclairage.......................................43
Entretien avant les vacances ou lors d’un déménage
DÉPANNAGE.....................................................
FEUILLE DE DONNÉES SUR LA PERFORMANCE..........................50
GARANTIE............................................................................................51
he refrigerator compartment.
.............27
.... 27
.................. 28
rdement à l'alimentation en eau.............................................31
ration de l'eau.........................................
portes................................................... 37
blettes du réfrigérateur .................................................................40
............................................................. 42
...................................44
.................. 35
........40
.............................. 42
ment.............43
W10790750C
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
■
Plug into a grounded 3 prong outlet.
■
Do not remove ground prong.
■
Do not use an adapter.
■
Do not use an extension cord.
■
Disconnect power before servicing.
■
Replace all parts and panels before operating.
■
Remove doors from your old refrigerator.
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
■
Use nonflammable cleaner.
■
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
■
Use two or more people to move and install refrigerator.
■
Disconnect power before installing ice maker (on ice maker
kit ready models only).
■
Use a sturdy glass when dispensing ice (on some models).
■
Do not hit the refrigerator glass doors (on some models).
follow
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
Proper Disposal of Your Old Refrigerator
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■ Take o ff th e d oors .
■ Leave the shelves in place so that children may not easily
climb inside.
Important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
2
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see “Refrigerator Safety.”
■ Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
“walk” the refrigerator when trying to move it, as floor
damage could occur.
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for a ¹⁄₂"
(1.25 cm) of space on each side and at the top. Allow for a 1"
(2.54 cm) space behind the refrigerator. If your refrigerator has an
ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 2" (5.08 cm) minimum space between the refrigerator and
wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a maximum
of 110°F (43°C). The preferred room temperature range for
optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
Clean Before Using
After you remove all of the packaging materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
¹⁄₂" (1.25 cm)
2" (5.08 cm)
3
Remove and Replace Refrigerator Doors and Drawer Front
A
B
Depending on the width of your door opening, it may be
necessary to remove the refrigerator doors to move the
refrigerator into your home.
IMPORTANT:
If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control OFF, and unplug the refrigerator or disconnect power.
Remove food and any adjustable door or utility bins from
doors.
Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet. Provide additional support for the
refrigerator door while the hinges are being removed. Do not
depend on the door gasket magnets to hold the door in place
while you are working.
All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", and ¹⁄₄" hex head socket wrenches,
®†
T25 screwdriver, #2 Phillips screwdriver, and a flat-blade
Torx
screwdriver.
Remove Doors and Hinges
1. Unplug refrigerator or disconnect power.
2. Remove the base grille. Grasp the grille firmly and pull it
toward you.
3. Starting with the right-hand side door, remove the parts for the
top hinge as shown in Top Hinge graphic. Lift the refrigerator
door from the bottom hinge pin.
4. Remove the hinge pin cover from the bottom hinge pin and
keep it for later use. See Bottom Hinge graphic.
5. Remove top hinge cover from left-hand side refrigerator door.
6. Remove the parts for
graphic. Lift the left-hand side door from the bottom hinge pin.
NOTE: On some models, remove the hinge pin cover from the
bottom hinge pin and keep it for later use. See Bottom Hinge
graphic.
Replace Doors and Hinges
1. Assemble the parts for the top hinges as shown in Top Hinge
graphic. Do not tighten the screws completely.
2. Replace the parts for the bottom hinge as shown in Bottom
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
3. Align the door so that the bottom of the refrigerator doors
align evenly
screws.
4. Replace the top hinge covers.
with the top of the freezer drawer. Tighten all
Remove and Replace Freezer Drawer Front
IMPORTANT: Two people may be required to remove and replace
the freezer drawer. Graphics are included later in this section.
To remove drawer front:
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front. See Drawer Front Removal graphic.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
3. Lift drawer front upward and off the screws.
Removal graphic.
†®TORX is a registered trademark of Acument Intellectual Properties, LLC.
the top hinge as shown in Top Hinge
See Drawer Front
4. The refrigerator leveling/roller assembly protrudes from each
side of the cabinet base. Remove the three screws attaching
each assembly, and remove the assemblies. See Refrigerator
Leveling/Roller Assembly graphic.
To replace drawer front:
1. Align the leveling/roller assembly with the holes on each side
of the refrigerator cabinet. Using the screws removed, reinstall
the assemblies to the cabinet base. Tighten the screws
completely.
2. Slide the drawer glides out of the freeze
the screws in the top of the drawer front into the slots in the
drawer brackets. See Drawer Front Replacement graphic.
3. Pull the drawer brackets toward you to position the two
screws in the bottom of the drawer front into the brackets and
completely tighten the four screws. See Drawer Front
Replacement graphic.
4. Replace the base grille.
Pull open the freezer drawer.
Align the three clips on the back of the base grille with the
three tabs at the base of the refrigerator.
Push the base grille in toward the refrigerator until it is
firmly in place.
A. Tab
B. Clip
r compartment. Insert
Final Steps
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Return all removable parts to doors and drawer and food to
refrigerator and freezer.
4
Door Removal and Replacement
Top Hinges
D
A. Hinge Cover Screw
B. Top Hinge Cover
5
C.
/16" Hex-Head Hinge Screws
D. Top Hinge
Bottom Hinges
A. Hinge Pin Cover
B. Bottom Hinge
C. Hinge Screws
A
B
C
A
B
C
Drawer Front Removal
A
A. Loosen 4 Door Bracket Screws
Leveling/Roller Assembly
A.
Assembly Screws
Drawer Front Replacement
A
5
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
ving a light bulb, turn Cooling OFF, and then disconnect the
remo
refrigerator from the electrical source. When you have finished,
reconnect the refrigerator to the electrical source and turn Cooling
ON. See “Using the Controls.”
Water Supply Requirements
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, th
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
after heavy usage. The tank capacity could be too low to keep
up with the requirements of the refrigerator.
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water Filtration
System.”
If you have questions about your water pressure, call a licensed,
qualified plumber.
e water pressure to the reverse osmosis
Connect the Water Supply
Read all directions before you begin.
IMPORTANT:
All installations must meet local plumbing code requirements.
Use copper tubing or Whirlpool supply line, Part Number
8212547RP, and check for leaks.
Install copper tubing only in areas where the temperatures will
remain above freezing.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Flat-blade screwdriver
⁷⁄₁₆" and ¹⁄₂" Open-end or two
adjustable wrenches
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"
(4.76 mm) saddle valve which reduces water flow and
easily.
Connect to Water Line
Style 1
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
Make sure it is a cold water pipe.
Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
5. Using
6. Fasten the shutoff valve to the cold water pipe with the pipe
a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you
have selected.
G
DEF
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten or you may crush the copper tubing.
¹⁄₄" Nut driver
¹⁄₄" Drill bit
Cordless drill
clogs more
A
B
C
E. Compression sleeve
F. Shutoff valve
G. Packing nut
6
7. Slip the compression sleeve and compression nut onto the
A
B
C
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe. Coil the copper
tubing.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long
enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in
order to connect the water tubing to an existing household
water line. Thread the provided nut onto the coupling on the
end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
A B C D E F G
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (provided)
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
E. Ferrule (purchased)
F. Nut (purchased)
G.Household water line
A. Bulb
B. Nut (provided)
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
A
B
D
E
Complete the Installation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
NOTES:
■ Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Allow 3 days to completely
fill ice container.
■ For models with a water dispenser, flush the water system.
See “Water Dispenser.”
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D. Compression nut
E. Valve inlet
6. On models with ice makers, the ice maker is equipped with a
built-in water strainer. If your water conditions require a
second water strainer, install it in the ¹⁄₄" (6.35 mm) water line
at either tube connection. Obtain a water strainer from your
nearest appliance dealer.
7
Handle Installation and Removal
Parts Included: Refrigerator door handles (2),
Freezer drawer handle (1)
Tools Needed: ¹⁄₈" Hex key wrench
Install Door Handles
NOTE: Handle mounting setscrews are preinstalled inside the
handle.
1. Remove the handles from the packaging inside the
refrigerator.
2. Open a refrigerator door. On the opposite door, place the
handle on the shoulder screws with the setscrews facing the
adjacent door.
Install Drawer Handle
1. With the freezer drawer closed, place the handle on the
shoulder screws with the setscrews facing down toward the
floor.
A
B
A
B
A. Shoulder screws
B. Setscrews inside the handle
3. Firmly push the handle toward the door until the handle base
is flush against the door.
4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in
the setscrew.
A. Should
B. Setscrews inside the handle
2. Firmly push the handle toward the drawer until the handle
base is flush against the drawer.
3. Insert the short end of the hex key into the left-hand hole and
slightly rotate the hex key until it is engaged in the setscrew.
4. Using a left to right motion tighten the setscrew a quarter-turn
at a time. Repeat until the screw feels tight.
Repeat steps 3 and 4 to fasten the right-hand setscrew to the
5.
shoulder screw.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
6. Save the hex key and all instructions.
er screw
5. Using a clockwise motion tighten the setscrew until the screw
feels tight.
6. Repeat steps 4 and 5 to fasten the lower setscrew.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
7. Repeat steps 2 through 6 to install the other handle onto the
adjacent refrigerator door.
8
Remove the Handles
1. While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is
engaged in the setscrew.
2. Using a right to left motion loosen the setscrew a quarter-turn
at a time.
3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the
handle away from the door or drawer.
4. If necessary, use a Phillips screwdriver to remove the shoulder
screws from the door.
Door Closing and Door Alignment
A
B
A
B
IMPORTANT: To comply with Americans with Disabilities Act (ADA)
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
Door Closing
The base grille covers the leveling screws and roller assemblies
located at the bottom of the refrigerator cabinet below the freezer
drawer. Before making adjustments, remove the base grille and
move the refrigerator to its final location.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs off the floor by turning the leveling screws
counterclockwise. The fr
3. So the doors will close easier, use a ¹⁄₄" hex driver to turn both
leveling screws clockwise. This will raise the front of the
refrigerator tilting it slightly downward to the rear. Turn both
leveling screws the same amount.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the screws.
ont rollers will be touching the floor.
¹⁄₄"
Door Alignment
If the space between the refrigerator doors and freezer drawer
looks uneven, you can adjust it using the following instructions:
1. Remove the top hinge cover.
2. Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.
3. Have someone hold the door in place or put a spacer between
the doors and drawer.
4. Tighten the top hinge screws once the door is in the desired
location.
5. Replace the top hinge cover.
FILTERS AND
ACCESSORIES
Water Filtration System
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Light
A. Leveling screw
B. Front roller
4. Open both doors again to make sure they close as easily as
you like and
slightly more to the rear by turning both leveling screws to the
right. It may take several more turns.
NOTE: To keep the refrigerator level, you should turn both
leveling screws the same amount.
5. Replace the base grille.
Pull open the freezer drawer.
Align the three clips on the back of the base grille with the
three tabs at the base of the refrigerator.
Push the base grille in toward the refrigerator until it is
firmly in place.
that they stay closed. If not, tilt the refrigerator
The water filter status light on the control panel will help you know
when to order and replace the water filter.
GOOD - The water filter icon on the control lights up in BLUE.
ORDER a replacement filter - The water filter icon on the
control lights up in YELLOW.
REPLACE the water filter - The water filter icon on the control
lights up in RED and “Replace Filter” will appear on the
display.
EXPIRED - The water filter icon lights up in RED and “Replace
Filter” flashes on the display.
NOTE: If water flow to your water dispenser or ice maker
decreases noticeably, change the filter sooner. The disposable
water filter should be replaced at least every 6 months,
depending on your water quality and usage.
After changing the water filter, reset the status. Press and hold
the WATER FILTER button for 3 seconds. When the system is
reset, the water filter icon will return to its BLUE color and the
words “Replace Filter” will disappear from the display.
Changing the Water Filter
A. Tab
B. Clip
1. Locate the water filter in the top-right corner of the refrigerator
compartment.
2. Lift open the filter cover door. The filter will be released and
then eject as the door is opened.
3. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
9
4. Take the new filter out of its packaging and remove the covers
from the O-rings. Be sure the O-rings are still in place after the
covers are removed.
5. With the arrow pointing up, align the new filter with the filter
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the filter
into place. You may need to press hard.
7. Flush the water system. See “Water Dispenser”.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, or
when the status indicator air filter icon turns on and starts flashing
when the refrigerator door is opened.
To order a replacement air filter, contact us. See “Accessories.”
1. Remove the used air filter by squeezing in on the side tabs.
2. Install the new air filter and reset the status indicator using the
instructions in the previous section.
Install Air Filter
(on some models)
The air filter reduces the buildup of odors. This helps to maintain a
cleaner environment inside the refrigerator.
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use. On some models,
the air filter is already installed at the factory.
Installing the Air Filter
Install the air filter behind the vented door, located along the rear
interior wall of the refrigerator compartment.
1. Remove the air filter from its packaging.
NOTE: An air filter status indicator is included with the air filter.
The indicator is not needed for models that display the air filter
status on the control panel.
2. Lift open the vented door.
3. Snap the filter into place.
Air Filter Status Indicator
The control panel displays the Air Filter status.
GOOD - The air filter icon on the control lights up in BLUE.
ORDER a replacement - The air filter icon on the control lights
up in YELLOW.
REPLACE air filter - The air filter icon on the control lights up in
RED and “Replace Filter” will appear.
EXPIRED - The air filter icon lights up in RED and “Replace
Filter” flashes on the control display.
After replacing the air filter, press and hold the AIR FILTER button
for 3 seconds. The filter icons will turn off. See “Using the
Controls.” When the system is reset, the air filter icon will return
to its BLUE color and the words “Replace Filter” will disappear
from the display.
NOTE: At any filter status, pressing and holding the AIR FILTER
button for 3 seconds will reset the air filter status to Good an
air filter icon will turn off.
d the
Install Produce Preserver
(on some models)
The produce preserver absorbs ethylene, to slow the ripening
process of many produce items. As a result, certain produce
items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Sensitivity to
Ethylene
Apples High Very High
Asparagus Med. Very Low
Berries Low Low
Broccoli High Very Low
Cantaloupe Med. High
Carrots Low Very Low
Citrus Fruit Med. Very Low
Grapes Low Very Low
Lettuce High Very Low
Spinach High Very Low
Installing the Produce Preserver
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
Ethylene
Production
hgiH yreVhgiHsraeP
10
1. Find the Produce Preserver housing inside the refrigerator.
IRRITANT
ATTENTION
Lisez des prudences sur le revers.
RITANT
IR
CAUTION
Read cautions on back.
2. Open the housing by pulling up and out on the back.
3. Remove the FreshFlow™ Produce Preserver pouches from
the packaging and place them into the housing.
NOTE: For best performance, always use two pouches.
4. Place the Produce Preserver housing onto the tab located on
the back wall of the crisper drawer.
Installing the Status Indicator
Accessories
The following accessories are available for your refrigerator. To
order, contact us and ask for the part numbers.
In the U.S.A., visit our web page www.kitchenaid.com/
accessories or call 1-800-901-2042.
In Canada, visit our web page www.whirlpoolparts.ca
or call 1-800-807-6777.
†
®
affresh
Order Part #W10355016
affresh
Order Part #W10355049
affresh
Order Part #W10355010
Water Filter:
Order Part # W10295370A or FILTER1
Air Filter:
Order Part #W10311524
Produce Preserver:
Order Part #W10346771A or FRESH1
Water Filter, Air Filter and Produce Preserver Bundle Pack:
Order Part #W10443987BL
Stainless Steel Cleaner:
†
®
Stainless Steel Wipes:
†
®
Kitchen & Appliance Cleaner:
or AIR1
The produce preserver comes with a status indicator, which
should be activated and installed at the same time the pouches
are installed.
MONTHS
REPLACE
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator until
the bubble pops, to activate the indicator.
3. Slide open the cap on the top of the produce preserver
housing.
4. Place the indicator in the top of the housing, facing outward.
5. Slide
the cap closed, and check that the indicator is visible
through the rectangular
hole in the cap.
NOTE: The cap will not easily close if the indicator’s bubble
has not been popped.
Replacing the Produce Preserver
The disposable pouches should be replaced every 6 months or
when the status indicator changes completely from white to red.
To order replacements, contact us. See “Accessories” for
information on ordering.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement pouches and status indicator using the
instructions in the previous sections.
REFRIGERATOR USE
Opening and Closing Doors
There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
A
A. Hinged seal
†® AFFRESH is a Trademark of Whirlpool, U.S.A.
11
Using the Controls
IMPORTANT:
Wait 24 hours for your refrigerator to cool completely before
adding food. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer temperature
controls to a colder than recommended setting will not cool
the compartments any faster.
The recommended setting should be correct for normal
household refrigerator use. The controls are set correctly
when milk or juice is as cold as you like and when ice cream is
firm.
NOTE: Areas such as a garage or porch may experience
warmer or colder temperatures and higher humidity than
inside the home. You may need to adjust the temperature
away from the recommended set points to accommodate for
these conditions.
If the temperature is too warm or too cold in the refrigerator or
freezer, before adjusting the controls, first check the air vents
located in the refrigerator and freezer compartments to be
sure they are not blocked by food items.
Control Panel
The control panel is located inside the refrigerator compartment.
This control operates both the refrigerator and freezer
compartments.
Adjusting the Temperature
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the following chart
as a guide.
Press either the FREEZER TEMP or FRIDGE TEMP button to
select the desired temperature setting from (1 box [least cold]
to 5 boxes [coldest]).
NOTE: Except when starting the refrigerator, do not adjust the
control more than one setting at a time. Wait 24 hours between
adjustments for the temperature to stabilize.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm FRIDGE TEMP one
setting (box) more
FREEZER too warm/too little ice FREEZER TEMP one
setting (box) more
REFRIGERATOR too cold FRIDGE TEMP one
setting (box) less
FREEZER too cold FREEZER TEMP one
setting (box) less
Cooling Off/On
Your refrigerator and freezer will not cool and water will not
dispense when cooling is turned off.
To turn cooling off, press and hold both the MAX COOL and
MOISTURE CONTROL buttons, at the same time, for
3 seconds. When cooling is off, “Cooling Off” will appear on
the display screen.
To turn cooling back on, press and hold both the MAX COOL
and MOISTURE CONTROL buttons, at the same time, for
3 seconds. When cooling is on, “Cooling Off” will disappear
and the previously selected settings will appear on the display
screen.
The control panel will display the Home Screen, as shown, when
either refrigerator door is opened.
Temperature Control
For your convenience, the temperature control is preset at the
factory. When you first install your refrigerator, make sure the
control is still set to the recommended setting as shown.
Recommended Setting (3 lit boxes)
Additional Features
Max Cool
The Max Cool feature assists during times of high refrigerator use,
full grocery loads or temporarily warm room temperatures.
Press MAX COOL to set the freezer and refrigerator to the
coldest temperature settings. Press MAX COOL again to
return to the selected temperature set point.
NOTES:
The Max Cool icon will be illuminated while the refrigerator
is in Max Cool mode.The displayed compartment
temperature settings will not change.
The Max Cool feature will turn off automatically after
24 hours.
12
Moisture Control
The moisture control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Moisture Control is on.
To turn on the Moisture Control feature, press and hold
MOISTURE CONTROL for 3 seconds.
To turn off the Moisture Control feature, press and hold
MOISTURE CONTROL for 3 seconds.
Door Open Alarm
The Door Open icon lights up when a door has been open for
5 minutes and cooling is on. An alert tone will sound three
times, and the Door Open icon will flash seven times. This
pattern will repeat every 2 minutes until all the doors are
closed completely. The feature then resets and will reactivate
when a door is left open again for 5 minutes.
NOTES:
To mute the audible alarm while keeping the doors open,
such as while cleaning the inside of the refrigerator, press
any button on the control panel. The alarm sound will be
temporarily turned off, but the Door Open icon will still be
displayed on the dispenser control panel.
All doors must be completely closed to turn off the Door
Open icon.
Water Dispenser
IMPORTANT:
Allow 3 hours for the refrigerator to cool down and chill water.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system, forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of
he dispenser.
t
1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
2. Release
and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
4 gal. (15 L) has been dispensed.
Dispense Water
the dispenser paddle for 5 seconds. Repeat steps 1
Sabbath Mode
Sabbath mode is designed for those whose religious observances
require turning off the lights.
In Sabbath Mode the temperature set points remain unchanged,
but the interior and dispenser lights turn off, all sounds and alarms
are disabled and the dispenser screen backlight turns off.
To turn on Sabbath Mode, press and hold both FREEZER
TEMP and FRIDGE TEMP at the same time for 3 seconds.
After 3 seconds, an “engage” tone will sound and the icons on
the control panel display will flash and then disappear.
NOTE: You must close the doors to turn off the lights. The
lights will remain off while the refrigerator is in Sabbath mode.
To turn off Sabbath Mode, press and hold both FREEZER
TEMP and FRIDGE TEMP at the same time for 3 seconds.
After 3 seconds, a “disengage” tone will sound and the
control panel will display the normal screen.
NOTE: After turning off Sabbath Mode, you must first close
the doors to turn ON the lights. Then the lights will function
normally.
NOTES:
Sabbath mode does not disable the water dispenser or the ice
maker. To turn off the ice maker, see “Ice Maker.”
If a power failure occurs or you unplug the refrigerator while it
is in Sabbath mode, it will take 10 minutes for the cooling
system to resume when power is restored.
Water Filter Status Light and Reset
The filter reset control allows you to restart the water filter status
tracking feature each time you replace the water filter. See “Water
Filtration System.”
Press and hold WATER FILTER for 3 seconds, to reset the
water filter status to Good. The Water Filter icon will turn blue.
Air Filter Status Light and Reset
The filter reset control allows you to restart the air filter status
tracking feature each time you replace the air filter. See “Install Air
Filter.”
Press and hold AIR FILTER for 3 seconds, to reset the air filter
status to Good. The Air Filter icon will turn blue.
1. Hold a container under the dispenser spout while pressing the
dispenser pad.
2. Release the dispenser pad to stop dispensing.
Ice Maker
(on some models)
IMPORTANT: For models with a water filter, after connecting the
refrigerator to a water source or replacing the water filter, fill and
discard three full containers of ice to prepare the water filter for
use.
Turning the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff
arm up or down.
13
Ice Storage Bin
1. Wash the ice storage bin with mild soap and warm water.
2. Slide the ice storage bin under the ice maker, and push it
toward the back as far as it will go.
3. Lower the arm on the ice maker to the “On” position.
NOTE: It usually takes approximately 24 hours for the ice
maker to begin producing ice. You may notice the ice has an
“off-taste.” If so, discard the first three batches of ice
produced. After that the “off-taste” should be gone.
To replace a shelf:
1. Slide the back of the shelf into the track in the wall of the
cabinet.
2. Guide the front of the shelf into the shelf track. Be sure to slide
the shelf in all the way.
Ice Production Rate
The ice maker should produce approximately 8 to 12 batches
of ice in a 24-hour period. Allow 3 days to completely fill the
ice container.
To increase ice production, lower the freezer and refrigerator
temperature. See “Using the Controls.” Wait 24 hours
between adjustments.
Remember
The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
Do not use anything sharp to break up the ice in the bin. This
can cause damage to the ice storage bin and the dispenser
mechanism.
Do not store anything on top of or in the ice maker or ice
storage bin.
REFRIGERATOR
FEATURES
NOTE: Your model may have some or all of these features.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Fold Away Shelf (on some models)
To retract the fold away shelf:
Retract the fold away section of the shelf by holding the front
of the shelf with one hand and lifting up on the center front of
the shelf. Then push back and down on the shelf until it slides
beneath the back section of the shelf.
To replace the fold away shelf:
Replace the fold away section of the shelf by holding the front
of the shelf with one hand and pulling the center of the shelf
until the fold away section is returned to its full shelf position.
Pantry Drawer
Pantry Drawer
To remove and replace the pantry drawer:
1. Slide pantry drawer out to the stop.
2. Lift front of pantry drawer with one hand while supporting
bottom of drawer with other hand. Slide drawer out the rest of
the way.
3. Replace the drawer by sliding it back in fully past the drawer
stop.
Pantry Drawer Cover
To remove and replace the pantry drawer cover:
1. Remove the pantry drawer.
2. From underneath, push up on the glass cover and pull it out.
3. Replace the pantry drawer cover by lowering it into place.
4. Replace the pantry drawer.
Refrigerator Shelves
The shelves in your refrigerator are adjustable to match your
individual storage needs.
Glass Shelves
To remove a shelf:
1. Remove items from the shelf.
2. Slide the shelf straight out to the stop.
3. Depending on your model, lift the back or front of the shelf
past the stop. Pull the shelf out the rest of the way.
14
Pantry Drawer Control
The amount of air flowing through the pantry drawer affects the
temperature inside the drawer.
The airflow control is located on the left side of the pantry drawer.
To adjust the airflow:
■ Colder - Slide the control forward, toward the front of the
pantry drawer. The airflow is open.
■ Cold - Slide the control all the way toward the rear of the
pantry drawer. The airflow is closed, as shown.
Crisper
■ Leafy vegetables: Wash in cold water, drain and trim or tear off
bruised and discolored areas. Place in plastic bag or plastic
container and store in crisper.
DOOR FEATURES
NOTE: Your model may have some or all of these features.
Condiment Bins
To remove and replace the condiment bins:
1. Tilt the bin by grabbing it and pulling outward.
2. Remove the bin by grabbing it and lifting it upward off the
glides.
3. Replace the bin by sliding it back onto the glides and then
push it closed.
Crisper Drawers
To remove and replace the crisper drawer:
1. Slide the crisper drawer straight out to the stop. Lift the front
and slide the drawer out the rest of the way.
2. Replace the drawer by sliding the drawer in fully past the stop.
Crisper Cover
To remove and replace the glass crisper cover:
1. Pull the glass straight out.
2. Replace the glass by pushing it straight in.
Crisper Humidity Control (on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) lets moist air out of the crisper for best storage of
fruits and vegetables with skins.
■ Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store in
a loosely closed paper bag on a refrigerator shelf.
■ Vegetables with skins: Place in plastic bag or plastic container
and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
Fresh Bin
(on some models)
To remove and replace the fresh bin:
1. Open the bin by grabbing the top center lip of the bin and
tilting the bin outward.
2. Remove the bin by grabbing both sides of the bin and lifting
the bin upward off the glides.
3. Replace the bin by sliding it back into its tilted position on the
glides and then push it closed.
15
Half-Height Bin
(on some models)
To remove and replace the half-height bin:
1. Tilt the bin by grabbing it and pulling outward.
2. Remove the bin by grabbing it and lifting it upward off the
glides.
3. Replace the bin by sliding it back onto the glides and then
push it closed.
3. Clean the exterior surfaces.
Painted metal: Wash painted metal exteriors with a clean,
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately to
avoid water spots.
ess steel: Wash stainless steel surfaces with a clean,
Stainl
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately to
avoid water spots.
NOTE: When cleaning stainless steel, always wipe in the
direction of the grain to avoid cross-grain scratching.
4. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille.
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
condenser should be cleaned every 2 to
REFRIGERATOR CARE
Cleaning
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT:
Because air circulates between both sections, any odors
formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid
odor transfer and drying out of food, wrap or cover foods
tightly.
For stainless steel models, stainless steel is corrosionresistant and not corrosion-proof. To help avoid corrosion of
your stainless steel, keep your surfaces clean by using the
following cleaning instructions.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, muriatic acid,
cleaning waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on exterior surfaces (doors and
cabinet), plastic parts, interior and door liners or gaskets. Do
use paper towels, scouring pads, or other harsh cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
not
Changing the Light Bulbs
IMPORTANT:
Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with an appliance bulb of the same size,
shape, and wattage.
To ensure optimum refrigerator performance, replace light
bulbs as soon as they burn out.
Refrigerator Compartment Light
The lighting located at the top of the refrigerator compartment
never needs to be replaced. If the lights do not illuminate when
the door is opened, call for assistance or service. In the U.S.A.,
call 1-800-253-1301. In Canada, call 1-800-807-6777.
Freezer Compartment Light (on some models)
1. Unplug the refrigerator or disconnect power.
2. Remove the light shield (on some models).
Top of the freezer compartment - Slide the light shield
toward the back of the compartment to release it from the
light assembly.
3. Replace the burned-out bulb with an appliance bulb(s) no
greater than 25 watts.
4. Replace the light shield.
5. Plug in refrigerator or reconnect power.
16
Loading...