KitchenAid KRFC704FSS, KRFC704FBS, KRFC604FSS Owner's Manual

French Door Refrigerator Réfrigérateur à porte à double battant Refrigerador de dos puertas

User Guide Guide de l’utilisateur Manual del usuario

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.kitchenaid.com. In Canada, register your refrigerator at www.kitchenaid.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.

Nous vous REMERCIONS d’avoir acheté ce produit de haute qualité. Enregistrer votre nouveau réfrigérateur sur le site internet www.kitchenaid.ca.

Pour référence ultérieure, consigner par écrit les numéros de modèle et de série de votre produit. Ceux-ci sont situés sur la paroi interne du compartiment de réfrigération.

LE AGRADECEMOS la compra de este producto de alta calidad. Registre su refrigerador en www.kitchenaid.com. En Canadá, registre su refrigerador en www.kitchenaid.ca.

Para referencia futura, tome nota del número de modelo y de serie del producto, ubicados en la pared interior del compartimiento del refrigerador.

Model Number/Numéro de modèle/Número de modelo __________________________________________ Serial Number/Numéro de série/Número de serie _______________________________________________

W10815171B

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

REFRIGERATOR SAFETY ......................... 3

PARTS AND FEATURES ...........................4

What’s New Behind the Doors? .............. 5

GETTING STARTED ..................................6

INSTALLATION INSTRUCTIONS ..............8

Unpack the Refrigerator ..........................8

Location Requirements ...........................8

Remove and Replace Refrigerator

Doors .......................................................9

Remove and Replace

Freezer Drawer Fronts ...........................12

Electrical Requirements ........................13

Water Supply Requirements .................13

Connect the Water Supply ....................13

Handle Installation and Removal ..........14

Refrigerator Leveling

and Door Closing ..................................16

FILTERS AND ACCESSORIES ..............17

Water Filtration System .........................17

Install Air Filter .......................................18

Install Produce Preserver ......................18

Accessories ...........................................19

REFRIGERATOR USE .............................19

Opening and Closing Doors ..................19

Using the Controls ................................20

External Dispenser Controls .................21

Lighting the Refrigerator .......................22

Water and Ice Dispensers .....................22

Ice Maker and Storage Bin ..................25

Shelves, Bins, and Drawers ..................25

Freezer Drawers ....................................28

Audio Reference ....................................28

REFRIGERATOR CARE ..........................29

Cleaning ................................................29

Lights .....................................................30

Vacation and Moving Care ....................30

TROUBLESHOOTING .............................31

PERFORMANCE DATA SHEET .............. 37

WARRANTY .............................................38

SÉCURITÉ DU RÉFRIGÉRATEUR..........39

PIÈCES ET CARACTÉRISTIQUES .........40

Quoi de neuf en coulisse? ....................41

MISE EN PLACE ......................................42

INSTRUCTIONS D’INSTALLATION ........ 44

Déballage du réfrigérateur ....................44

Exigences d’emplacement ....................44

Retrait et réinstallation des portes

du réfrigérateur ......................................45

Retrait et réinstallation de l’avant

du tiroir de congélation .........................48

Spéciﬁcations électriques .....................49

Spéciﬁcations de l’alimentation

en eau ....................................................49

Raccordement à la canalisation

d’eau ......................................................49

Installation et retrait des poignées ........50

Nivellement du réfrigérateur

et fermeture de la porte .........................52

FILTRES ET ACCESSOIRES ..................53

Système de ﬁltration d’eau ...................53

Installation du ﬁltre à air ........................54

Installation du conservateur de

produits frais ..........................................54

Accessoires ...........................................55

UTILISATION DU RÉFRIGÉRATEUR .....55

Ouverture et fermeture des portes ........55

Utilisation des commandes ..................56

Commandes de distributeur externe ....57

Éclairage du réfrigérateur ......................58

Distributeurs d’eau et de glaçons .........58

Machine à glaçons et bac

d’entreposage ......................................61

Tablettes, balconnets et tiroirs ..............62

Tiroirs du congélateur ...........................64

Référence audio ....................................64

ENTRETIEN DU RÉFRIGÉRATEUR .......65

Nettoyage ..............................................65

Lampes ..................................................66

Précautions à prendre pour les

vacances ou le déménagement ............66

DÉPANNAGE ............................................67

FICHE DE DONNÉES RELATIVES

AU RENDEMENT .....................................74

GARANTIE ................................................75

SEGURIDAD DEL REFRIGERADOR ......77

PIEZAS Y CARACTERÍSTICAS ..............78

¿Qué hay de nuevo detrás de

las puertas? ...........................................79

PARA COMENZAR ..................................80

INSTRUCCIONES DE INSTALACIÓN ....82

Desembale el refrigerador .....................82

Requisitos de ubicación ........................82

Cómo retirar y volver a colocar

las puertas del refrigerador ...................83

Cómo retirar y volver a colocar el

frente de los cajones del congelador ....86

Requisitos eléctricos .............................87

Requisitos de suministro de agua ........87

Conexión del suministro de agua .........87

Cómo instalar y quitar las manijas ........89

Nivelación del refrigerador

y cierre de las puertas ...........................90

FILTROS Y ACCESORIOS .....................91

Sistema de ﬁltración de agua ...............91

Instalación del ﬁltro de aire ...................93

Instale el preservador de alimentos

frescos ...................................................93

Accesorios .............................................94

USO DEL REFRIGERADOR ....................94

Cómo abrir y cerrar las puertas ............94

Uso de los controles .............................95

Controles del despachador externo .....97

Iluminación del refrigerador ..................97

Despachadores de agua y de hielo ......97

Fábrica de hielo y depósito ................101

Estantes, depósitos y cajones ............101

Cajones del congelador ......................104

Referencia de audio ............................104

CUIDADO DEL REFRIGERADOR ........105

Limpieza ..............................................105

Luces ...................................................106

Cuidado durante las vacaciones

y las mudanzas ...................................106

SOLUCIÓN DE PROBLEMAS...............107

HOJA DE DATOS

DE RENDIMIENTO ................................114

GARANTÍA..............................................115

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still dangerous—even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

PARTS AND FEATURES

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

In-Door-Ice ice storage

Temperature Control UI

Under-shelf storage (on some models)

Air filter

Herb bin storage

Water filter

Removable bin

FreshSeal™ dairy bin

Slide-away split shelf

Dual gallon storage

Pull-out tray

FreshSeal™ crispers

Temperaturecontrolled pantry drawer

What’s New Behind the Doors?

Your KitchenAid® French door bottom-mount refrigerator comes equipped

with various innovative storage and energy efﬁcient features.

Energy and Normal Operating Sounds

Your new French door bottom-mount refrigerator has been designed with a linear compressor to optimize energy efﬁciency and better regulate temperatures to match cooling demand. You may notice that it operates differently than your previously owned refrigerator. It is normal for the high-efﬁciency compressor to run for extended periods of time at varying speeds in order to consume only the energy necessary for optimum efﬁciency. In addition, during various stages of the cooling cycle, you may hear normal operating sounds that are unfamiliar to you.

In-Door-Ice® Ice Dispensing System

The ice maker and ice storage bin are located in the door for easy access to ﬁltered ice while freeing up valuable shelf space inside.

Dual Evaporator

The refrigerator and freezer compartments have separate evaporators to provide fresh food and frozen food with optimal storage climates: cool and humid in the fresh food, cold and dry in the freezer, no mixing of air between the compartments to reduce the transfer of food odors and tastes from refrigerator, and allow freezer air to remain dry to control frost and reduce freezer burn.

Air Filter

An air ﬁlter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator. Replace your air ﬁlter every 6 months for maximum odor reduction.

Produce Preserver

Ethylene is a natural gas produced by fruits and vegetables to promote ripening. The Produce Preserver absorbs ethylene to delay the over-ripening of fresh produce. As a result, certain produce items will stay fresh longer.

EveryDrop™ Water Filter

EveryDrop™ water ﬁlters are NSF®† Certiﬁed to reduce most contaminants, including chlorine taste and odor, lead, pesticides, and trace amounts of pharmaceuticals. EveryDrop™ brand ﬁlters are the only ﬁlters tested and certiﬁed for your refrigerator system. Replace your EveryDrop™ ﬁlter every 6 months for maximum contaminant reduction.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired amount of ﬁltered water in handy increments 8, 16, or 24 oz.

Water Dispenser with Favorite Fill

The Favorite Fill feature allows you to save 2 custom presets that can be programmed for favorite items that are frequently ﬁlled like a coffee pot or a water bottle.

Slide-Away Split Shelf

This shelf features a versatile design that allows three-quarters of the shelf to retract to accommodate taller items, up to 16.75 inches. This ﬂexibility helps maximize storage space and optimize organization.

Removable Door Bins

Door bins that can be easily removed from the metal ﬁnish base they sit on, making them ideal for carrying condiments or items from refrigerator to table. The bins are dishwasher safe for easy cleaning.

FreshSeal™ Dairy Bin

A dedicated dairy bin with the FreshSeal™ gasket to help extend the freshness and preserve the ﬂavor of butter and other dairy items.

FreshSeal™ Crispers

These upgraded crisper drawers use a gasket seal to maintain the ideal temperature and humidity levels to keep produce fresh longer. These drawers also feature premium soft-close glides that provide the best extension for easy access and maximum visibility to your produce items.

Pull-Out Tray

The tray fully extends for easy access and visibility. The tray also features soft self-close glides that provide effortless movement, even when fully loaded. The tray is removable, making cleaning easy.

Herb Storage Bin

This is a cylinder with FreshSeal™ to keep sensitive items like herbs fresh longer. The container allows water to be added to keep stems wet without covering leaves. It can be placed anywhere in the refrigerator and accommodates tall items like parsley, cilantro, and rosemary in addition to herbs like oregano, thyme, and mint.

Under Shelf Storage (on some models)

Utilizes typically empty space beneath the shelf to create a prep zone ideal for dough, desserts, casseroles, or marinating meats. The slide-out pan is oven and dishwasher safe and easily transitions from fridge to oven.

Adjustable Shelves on Flipper System

Shelves that can be adjusted up or down easily with the ﬂip of a lever, allowing them to be adjusted without having to unload them. The shelves are easy to clean and let you use the whole shelf edge to edge for full visibility and accessibility.

Temp Control Pantry

Four temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from meat/ﬁsh, cold drinks, deli/cheese, and wine. Pantry slides opens effortlessly, even when fully loaded, with soft, self-close glides and features the best extension in freestanding refrigeration.

3-Tier Freezer Drawer with Extend-Freeze™ Setting

A drawer system that organizes items on 3 levels making them easier to store and ﬁnd. The lower drawer includes a divider. There’s also an in-door pizza pocket, a pull-out drawer for smaller items and third level glass shelf for small, ﬂat items. The Extend-Freeze™ setting takes the entire freezer to its coldest setting to help reduce freezer burn and extend the life of frozen items.

†®

NSF is a registered trademark of NSF International.

Fingerprint-Resistant Steel and Black Stainless Steel (on some models)

A specialized coating for stainless steel that resists smudges, ﬁngerprints, and water marks. It is easy to clean with just water and a towel.

LED Lighting

There is bright LED strip lighting for maximum illumination. LED lights do not require replacement.

Door Alarm

A helpful alarm sounds when the refrigerator door or freezer drawer is left ajar.

GETTING STARTED

Power Outage Indicator

If the power should go out while you are away from home, this indicator will let you know that the refrigerator has been without power.

To view videos on door removal/

replacement, door adjustment, water

filter installation, air filter installation,

shelf adjustment or removal, and Wi-Fi

(if applicable) connectivity, scan the code

to the left with your mobile device.

INSTALLATION CHECKLIST

✔ Electrical Power

❑ Plug refrigerator into a grounded 3 prong outlet.

✔ Doors

❑ If doors need to be removed during installation, see the

“Remove and Replace Doors” section in the instructions.

❑ Check that handles are secure and installed according to the

instructions.

❑ Doors seal completely. ❑ Refrigerator is level. (Remove base grille and adjust leveling

feet so they are snug against the oor.)

❑ Doors are even across the top. (Use door alignment feature if

necessary.)

❑ Base grille is properly attached to the refrigerator.

✔ Ice and Water System (on some models)

❑ Connect refrigerator to a cold water supply with 20-120 psi

water pressure, as specied in the instructions.

❑ Make sure the household water supply is connected and

turned on.

❑ Check that the water supply line behind refrigerator is not

kinked.

❑ Only use recommended water supply tubing, copper, or PEX,

as specied in the instructions.

❑ Install water lter according to the instructions. ❑ Flush water system with 3 gallons of water, as specied in the

instructions.

❑ Check for water leaks at all connections. ❑ Turn on ice maker if refrigerator is connected to water supply.

(If not connected to water supply, turn off ice maker.)

✔ Final Checks

❑ Install air lter and Produce Preserver according to

instructions in corresponding packaging.

❑ Remove all shipping material. ❑ Set temperature controls to the recommended setting. ❑ Save instructions and other literature. ❑ Send in registration card or register your product online.

WATER FILTER INSTALLATION

❑ Locate the water lter compartment in the lower left-hand side

of the refrigerator compartment. Push on the right side of the lter door to open.

❑ Align the arrow on the water lter cap with the cutout notch in

the lter housing and insert lter.

❑ Once the lter is inserted, turn the lter clockwise 90° (¼ turn)

until it locks into the housing.

❑ Push water lter door closed to latch. ❑ Flush 3 gallons of water through the water system to clear air

from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser ow.

NOTE: If the lter is not installed correctly, water may dispense at a lower ow rate and there will be slower ice production. Improper lter installation may also cause the

water lter housing to leak.

DOOR ALIGNMENT

Align Refrigerator Doors

Shelf Height Adjustment

✔ If doors are uneven:

❑ Ensure the refrigerator is level. ❑ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

❑ Insert the short end of the ¹⁄

" hex key wrench (packed with the

Door Handle Installation Instructions) into the bottom hinge pin

until it is fully engaged in the alignment screw. To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left.

❑ Continue to turn the alignment screw until the tops of the

doors are aligned.

A. Bottom hinge pin B. ¹⁄8" hex key wrench

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

❑ Carefully lift the shelf off the shelf mounts and turn the ipper

to the desired orientation.

❑ Repeat for remaining shelf mounts. ❑ Ensure the shelf is properly seated on the shelf mounts.

ENERGY SAVER MODE AND NORMAL OPERATING SOUNDS

Your new French Door Bottom-Mount refrigerator has been designed to optimize energy efciency and better regulate temperatures to match cooling demand.

You may notice that it operates differently from your previously owned refrigerator.

It is normal for the high-efciency compressor to run for extended periods of time at varying speeds in order to consume only the energy necessary for optimum efciency.

In addition, during various stages of the cooling cycle, you may hear normal operating sounds that are unfamiliar to you.

Energy Saver Mode

Turns off the anti-sweat heaters to save the customer power. When the icon is bright, the function is activated (heaters OFF); icon off means that it is inactive (heaters ON). The user can toggle

the feature by pressing the button. If the user lives in a climate with high humidity, Energy Saver mode is not recommended.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Refrigerator Delivery

■ A minimum door opening of 33" (838 mm) is required. If door opening is 36" (914 mm) or less, then removal of doors, drawer, and hinges is required.

■ Cart the refrigerator from the side for all door openings.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your ﬁngers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, ﬂammable ﬂuids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

■ Dispose of/recycle all packaging materials.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow for a ¹⁄2" (1.25 cm) space on each side and at the top. Allow for a 1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a ﬁxed wall, leave a 3³⁄4" (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Refrigerator Care” section.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

¹⁄2" (1.25 cm)

3³⁄4" (9.5 cm)

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening to see whether or not you need to remove the refrigerator doors to move the refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control off. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors. TOOLS NEEDED: TORX®† T25®† screwdriver and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Water Dispenser

Tubing Connection

A. Outer ring

Wiring Plug

Top Right Hinge

A. TORX® T25® screws B. Hinge cover screw C. Top hinge cover D. Top hinge

Door at 90° Angle

to Cabinet°

Top Left Hinge

A. TORX® T25® screws B. Ground wire (Do not remove.) C. Do not remove screws.

†

®TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.

90°

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Bottom Door Hinge

For your convenience, the refrigerator doors have bottom hinges with door closers. These closers allow the doors to swing fully closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly, the doors must be removed only when open to a 90° angle to the front of the cabinet. If one or both doors were not at a 90° angle when removed, the bottom door hinge must be reset.

90°

Reset the Door Hinge

1. Lift the door from the bottom hinge pin and place it on a ﬂat

surface.

2. Using a TORX® T25® screwdriver, remove the bottom hinge

with the bushing from the cabinet.

A. Hinge base parallel to the bottom edge of the door

4. Turn the hinge until the hinge base is at a 90° angle to the

bottom edge of the door.

90°

A. Hinge base turned to a 90° angle with the bottom edge of the door

5. Remove the hinge from the door. Using a driver with a #2

square bit, reattach the bottom hinge to the refrigerator cabinet.

6. The hinge is now reset and prepared for the door to be

replaced. See “Replace Refrigerator Doors” later in this section.

Remove Refrigerator Doors

WARNING

A. Bushing B. Hinge base

3. Insert the bottom hinge and bushing into the corresponding

slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the bottom of the door.

Electrical Shock Hazard Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Remove Right-Hand Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Using a Phillips screwdriver, remove the cover from the top

hinge.

4. Using the TORX® T25® screwdriver, remove the 3 screws from

the top hinge and set aside.

A. Top hinge cover screw B. Top hinge cover

C. TORX® T25® screws D. Top hinge

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5. Open the door until it is at a 90° angle to the front of the

cabinet.

6. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Door

IMPORTANT: The tubing and wiring for the water dispenser run through the left-hand door hinge, so they must be disconnected before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

3. Disconnect the wiring plug located on top of the door hinge.

■ Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of the plug apart.

NOTE: Do not remove the green ground wire. It should remain attached to the door hinge.

4. Using the TORX® T25® screwdriver, remove the 3 internal

screws from the top hinge and set aside. NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

A. Top hinge cover screw B. Top hinge cover

2. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pull up on the clasp. Then, pull the tubing out of the fitting.

NOTE: The water dispenser tubing remains attached to the left-hand refrigerator door.

A. TORX® T25® screws B. Ground wire (Do not remove.)

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door. NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a doorway.

■ Only if necessary, use a TORX

T25® screwdriver to

remove the bottom hinges and brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the 3 TORX® T25® screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the 3 TORX® T25® screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing. Insert the tubing ﬁrmly into the ﬁtting until it stops. Close the

clasp around the tubing. The clasp snaps into place between the ﬁtting and the collar. Connect blue female side with blue male side and clasp. Repeat with gray female and gray male side.

4. Reconnect the electrical wiring.

■ Push together the 2 sections of the wiring plug.

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the top screws,

located at the bottom inside of the drawer front, with the drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the studs into the slots.

Final Steps

1. Completely tighten the 5 internal TORX® T25® screws (3 on

the right-hand door hinge and 2 on the left-hand door hinge).

2. Replace both top hinge covers.

Remove and Replace

Freezer Drawer Fronts

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the 2 top screws that fasten the drawer front to the

drawer glides. The 2 screws (1 on the left-hand side and 1 on the right-hand side) are located inside the drawer front.

3. Remove the 2 screws at the bottom, inside the drawer front

that fasten the drawer front to the drawer glides.

4. Lift up on the drawer front to release the screws from the

drawer glide bracket slot.

A. Drawer front screw

3. Tighten the 2 screws at the top of the drawer front (1 on the

left-hand side and 1 on the right-hand side) and replace the 2 screws on the bottom.

Final Steps

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

A. Drawer glide bracket slots

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See “Using the Controls” section.

3. Return all removable parts and food to the drawers.

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its ﬁnal location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115-volt, 60 Hz, AC-only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and ﬂavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation or cleaning, turn off cooling, then disconnect the refrigerator from the electrical source. When you have ﬁnished, reconnect the refrigerator to the electrical source and turn on cooling. See “Using the Controls” section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualiﬁed plumber.

NOTE: If the water pressure is less than what is required, the ﬂow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■ Check to see whether the sediment ﬁlter in the reverse

osmosis system is blocked. Replace the ﬁlter if necessary.

■ Allow the storage tank on the reverse osmosis system to reﬁll

after heavy use. The tank capacity could be too small to keep up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not recommended.

■ If your refrigerator has a water ﬁlter, it may further reduce

the water pressure when used in conjunction with a reverse osmosis system. Remove the water ﬁlter. See “Water Filtration System” section.

If you have questions about your water pressure, call a licensed, qualiﬁed plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing must be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ Copper and PEX tubing connections from the household

water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■

⁄16" and 1⁄2" open-end wrenches or 2 adjustable wrenches

■ ¼" nut driver

NOTE: Do not use a piercing-type or ³⁄16" (4.76 mm) saddle valve which reduces water ﬂow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1⁄2" household supply line.

NOTE: To allow sufﬁcient water ﬂow to the refrigerator, a minimum

⁄2" (12.7 mm) size household supply line is recommended.

A B

A. Sleeve B. Nut

C. Copper tubing (to refrigerator) D. Household supply line (½" [12.7 mm] minimum)

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1⁄4" (6.35 mm) O.D. (outside diameter) soft copper tubing to connect the shut-off valve and the refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve B. Compression nut

C. Copper tubing

Complete the Installation

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ﬂush out tubing until water is clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the ﬁnal connection to the inlet of the water valve to avoid possible water valve malfunction.

6. Bend the copper tubing to meet the water line inlet which

is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions speciﬁc to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Conﬁrm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water and Ice Dispensers”

section.

NOTE: Allow 24 hours to produce the ﬁrst batch of ice. Discard the ﬁrst 3 batches of ice produced. Allow 3 days to completely ﬁll the ice storage bin.

Handle Installation and Removal

Parts Included: refrigerator door handles (2), refrigerated drawer handles (2), freezer drawer handle (1), 1⁄8" hex key, spare setscrew(s)

NOTE: The freezer drawer handle is shorter than the refrigerator door handles. Handle style may vary by model.

Install Handles

Refrigerator Doors NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed

door, place a handle onto the shoulder screws so that the setscrews are facing the adjacent door.

A. Copper tubing B. “P” clamp

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

C. Compression nut D. Compression sleeve

A. Shoulder screws B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is ﬂush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews. IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto the

adjacent refrigerator door.

Freezer Drawer

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the ﬂoor.

4. Using a left-to-right motion, tighten the setscrew a quarter

turn at a time just until it begins to contact the shoulder screw. Do not fully tighten.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew to the

shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews. IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

2. Using a right-to-left motion, loosen the setscrew a quarter

turn at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

A. Shoulder screw B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle

base is ﬂush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

Remove and Replace Handle Medallions (optional)

The handles for your model have red medallions on the ends. Replacement medallions are available for purchase. See “Accessories” to order.

1. Using a ¹⁄8" hex key, remove the medallion from the end of the

handle.

2. Replace medallion.

3. Using the fastener removed in Step 1, attach the medallion to

the handle.

A. Handle medallion

Refrigerator Leveling

and Door Closing

The base grille covers the adjustable brake feet and roller assemblies located at the bottom of the refrigerator below the freezer drawer. Before making any adjustments, remove the base grille and move the refrigerator to its ﬁnal location.

Tools Needed: ¼" hex driver Tools Provided: ¼" hex key

1. Use a ¼" hex nut driver to remove both screws in base grille.

2. Remove the base grille. Using both hands, grasp the grille

ﬁrmly and pull it toward you. Open the freezer drawer to access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake feet by turning them counterclockwise. The front rollers will be touching the ﬂoor.

To Align the Doors:

■ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

■ Insert the short end of the ¹⁄

the Door Handle Installation Instructions) into the bottom

" hex key wrench (packed with

hinge pin until it is fully engaged in the alignment screw. To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

■ Continue to turn the alignment screw until the doors are

aligned.

3. Move the refrigerator to its ﬁnal location.

4. Using the 1⁄4" hex driver, lower the brake feet. Turn them

clockwise until the rollers are off the ﬂoor and both brake feet are snug against the ﬂoor. This keeps the refrigerator from rolling forward when opening the refrigerator doors or freezer drawer.

IMPORTANT: If you need to make further adjustments involving the brake feet, you must turn both brake feet the same amount to keep the refrigerator level.

5. Use a level to make sure the refrigerator is level from side to

side and front to back.

6. Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of the freezer drawer is even. If necessary, align the doors.

A. Bottom hinge pin B. ¹⁄8" hex key wrench

7. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled open, adjust the brake feet.

To Steady the Refrigerator:

■ Open the freezer drawer. Using a

⁄4" hex driver, turn both brake feet clockwise the same amount until the brake feet are snug against the ﬂoor. Check again. If not satisﬁed, continue to adjust the brake feet by half turns of the screw until the refrigerator does not roll forward when the drawer is opened.

NOTE: Having someone push against the top of the refrigerator takes some weight off the brake feet. This makes it easier to turn the screws.

8. Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille into place. Use a ¼" hex nut driver to reinstall screws.

FILTERS AND ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Replace and Install the Water Filter

The water lter should be replaced every 6 months based on a ow rate of .50 gpm—.60 gpm that lters 200 gallons of water.

To order a replacement lter, contact us. See “Accessories” section in the User Guide for information on ordering.

NOTE: If the ﬁlter is not installed correctly, water may dispense at a lower ﬂow rate and there will be slower ice production. Improper ﬁlter installation may also cause the water ﬁlter housing to leak.

1. Push the water ﬁlter door to open, located bottom left of

refrigerator compartment.

4. Remove the water ﬁlter cap from the water ﬁlter.

5. Install the water ﬁlter cap onto the new ﬁlter. Be sure to align

the arrows so the groves in ﬁlter align with ribs in ﬁlter cap.

6. Insert the ﬁlter into the housing.

2. Twist the water ﬁlter and turn 90° counterclockwise to unlock.

3. Pull the ﬁlter out of the housing.

7. Twist the water ﬁlter and turn 90° clockwise until it locks into

place and that arrows are aligned.

8. Push the water ﬁlter door closed.

The Water Filter Status Light

Replacing the Air Filter

The water ﬁlter status lights will help you know when to change your water ﬁlter.

■ ORDER FILTER (yellow) — It is almost time to change the

water ﬁlter. “Order Filter” display is ON all of the time but OFF in Showroom mode and Sabbath mode.

■ REPLACE FILTER (red) — Replace the water ﬁlter. While

you are dispensing water, “Replace Filter” icon will ﬂash constantly from the beginning to the end of dispensing. After 14 days without replacing the Water Filter, the “Replace Filter” icon will blink 7 times and an alert tone will sound 3 times at the end of dispensing.

■ RESET FILTER — Touch MAX COOL and MAX ICE together

for 3 seconds to reset water ﬁlter. The display will do a 3-second countdown, then ﬂash the icon and play a tone.

Install Air Filter

An air ﬁlter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator.

On some models, your refrigerator’s accessory packet includes an air ﬁlter which must be installed prior to use.

Installing the Air Filter

Install the air ﬁlter behind the vent cover, located on the rear wall near the middle of the refrigerator.

1. Remove the air ﬁlter from its packaging.

2. Pull out plastic cover over the vented cover.

NOTE: When cover is removed for the ﬁrst time, a small foam part the size of the ﬁlter will need to be discarded.

3. Snap the ﬁlter into place.

A. Air filter

The disposable air ﬁlter should be replaced every 6 months. To order a replacement air ﬁlter, contact us. See “Accessories”

section in the User Guide for information on ordering.

1. Remove the used air ﬁlter by squeezing in on the side tabs.

2. Install the new air ﬁlter following the instructions in the

previous sections.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate-to-high amounts of ethylene.

Sensitivity

to Ethylene

Apples High Very High Asparagus Medium Very Low Berries Low Low Broccoli High Very Low Cantaloupe Medium High Carrots Low Very Low Citrus Fruit Medium Very Low Grapes Low Very Low Lettuce High Very Low Pears High Very High Spinach High Very Low

Installing the Produce Preserver

For your convenience, the suction-mounted produce preserver can be installed in either the crisper or the refrigerated drawers.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.

Ethylene

Production

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer according to the instructions provided in the package.

REFRIGERATOR USE

Replacing the Produce Preserver

The disposable packet(s) should be replaced every 6 months or when the status indicator changes completely from white to red.

To order replacements, contact us. See “Accessories” section for information on ordering.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using the

instructions included in the package.

Accessories

The following accessories are available for your refrigerator. To order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.kitchenaid.com or call 1-800-422-1230.

In Canada, visit our webpage www.kitchenaid.ca or call

1-800-807-6777. affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016 In Canada, order Part #W10355016B

affresh® Stainless Steel Wipes: In U.S.A., order Part #W10355049 In Canada, order Part #W10355049B

affresh® Kitchen & Appliance Cleaner: In U.S.A., order Part #W10355010 In Canada, order Part #W10355010B

Water Filter: In U.S.A., order Part #EDR2RXD1 In Canada, order Part #EDR2RXD1B

Air Filter: Order Part #W10311524 or AIR1

Produce Preserver Starter kit: Order Part #P1UB6S1

Produce Preserver Reﬁll kit: Order Part #P1KC6R1

Door Handle Medallions: Order Part #W10762987 (Black) Order Part #W10762993 (Chrome)

Opening and Closing Doors

There are 2 refrigerator compartment doors. The doors can be opened and closed either separately or together. There is a vertically hinged seal on the left refrigerator door.

■ When the left-side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the 2 doors.

A. Hinged seal

The refrigerator compartment door switch is located in the top left and right hinge cover.

■ The door switch uses magnet to sense door opening/closing.

■ Ensure there are no magnet or electronic devices (Speaker,

CoolVox, etc) within 3 inches of the hinge cap.

NOTE: The light and internal user interface (UI) will not turn on if the door opening is not detected.

A. Hinge cover

Using the Controls

The Temperature Control UI is located above the external dispenser and on the side of the left refrigerator door.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are preset at the factory.

When you ﬁrst install your refrigerator, make sure that the controls are still set to the recommended set points. The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the set points to a colder-thanrecommended setting will not cool the compartments any faster.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, ﬁrst check the air vents to be sure they are not blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is ﬁrm.

NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

1. Touch [—]/[+] for Refrigerator or [—]/[+] for Freezer and toggle

through temperature set points. NOTE: To view temperature in degrees Celsius, touch and

hold the [°F/°C] button for 3 seconds and the temperature display will change. To return to Fahrenheit, touch and hold the [°F/°C] for 3 seconds and the temperature display will change.

To activate Temperature mode for Drawer, touch DRAWER and toggle through 4 optional temperature settings: Meats • Fish, Cold Drinks, Deli • Cheese, and Wine. The display will show the temperature set point of the selected setting for the Drawer.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set-point range: 33°F to 45°F (1°C to 7°C) Freezer set point range: -6°F to 5°F (-22°C to -15°C)

1. Touch [—]/[+] to adjust the Refrigerator zone. The display will

show the temperature set point of the selected compartment as shown.

2. When the temperature in is the range of Extend-Freeze™,

the display will light up. Extend-Freeze™ is activated at the coldest Freezer set point.

When adjusting temperature set points,

use the following chart as a guide:

CONDITION: TEMPERATURE ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR setting 1° higher REFRIGERATOR too warm REFRIGERATOR setting 1° lower FREEZER too cold FREEZER setting 1° higher FREEZER too warm/

FREEZER setting 1° lower

too little ice

Extend-Freeze™

This feature acts on the most-relevant storage parameters that must be controlled to minimize moisture migration from frozen food. This in turn reduces the freezer burn occurrence.

To turn on the Extend-Freeze™ feature, toggle to the coldest Freezer temperature set point.

To turn off the Extend-Freeze™ feature, toggle from the coldest freezer set point to any other temperature.

Max Cool

Sound On/Off

The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

■ To turn on the Max Cool feature, press the Max Cool button.

When the button is pressed, the icon will blink 3 times and appear on the display screen.

■ To manually turn off the Max Cool feature, press the Max

Cool button and the display will blink 3 times and turn off. The Max Cool feature will remain ON for 24 hours unless manually turned off. Adjusting the refrigerator temperature will automatically turn off the Max Cool feature.

NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Max Ice

The Max Ice feature assists with increasing the cooling for the freezer compartment in order to increase ice production.

■ To turn on or off the Max Ice feature, press the Max Ice

button. When the button is pressed to turn the feature on, the icon will blink 3 times and appear on the display screen.

■ To manually turn off the Max Ice feature, press the Max Ice

button and the display will blink 3 times and turn off. The Max Ice feature will remain ON for 24 hours unless manually turned off. Adjusting the freezer temperature will automatically turn off the Max Ice feature.

NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Water Filter Reset

Displays the status of the water filter. To reset the water filter, press MAX ICE and MAX COOL for 3 seconds. After countdown, the Good icon will blink 3 times and remain lit.

NOTE: The water ﬁlter status lights on the internal controls will let you know when to change your water ﬁlter.

■ ORDER FILTER (Yellow) — Order a replacement water ﬁlter.

■ REPLACE FILTER (Red) — Replace the water ﬁlter. While you

are dispensing water, Replace Filter icon will ﬂash constantly from beginning to the end of dispensing. After 14 days without replacing the Water Filter, the Replace Filter icon will blink 7 times and an alert tone will sound 3 times, at the end of dispensing. See “Water Filtration System” section.

NOTE: REPLACE FILTER will remain illuminated if a ﬁlter reset is not done.

■ RESET FILTER — Touch MAX ICE and MAX COOL at the

same time on the temperature control display for 3 seconds to reset water ﬁlter. The display will do a 3-second countdown and then ﬂash the icon and play a tone.

Energy Saver

The Sound button allows the customer to turn the sound on and off.

■ To turn on the Sound feature, press the Sound button. When

the button is pressed, the Sound icon will blink 3 times and appear on the display screen.

■ To manually turn off the Sound feature, press the Sound

button and the display will blink 3 times and turn off.

Power Outage

The Power Outage indicator lets you know if the power supply to the refrigerator has been OFF and the freezer temperature has risen.

The control panel display will read “Power Outage” and an alert tone will sound 3 times. Touch any button to stop the tone and turn off the Power Outage icon.

Once the power outage has been conﬁrmed, “Power Outage,” will disappear.

Showroom Mode

This mode is used when the refrigerator is on display in a retail store or if you want to turn the cooling off and deactivates all other functions except interior lighting). Showroom mode can be used when going on vacation, see “Vacation and Moving Care” section for proper steps on leaving your refrigerator in this mode for long periods of time.

If you turn on Showroom mode, the word “Showroom” will light up on the display. Enter or Exit Showroom mode by pressing and holding °F/°C and DRAWER at the same time for 3 seconds.

NOTE: Empty ice maker if refrigerator is going to be turned off for an extended period of time.

Sabbath Mode

Sabbath mode is designed to have all the beneﬁts of saving even more energy, yet maintaining food freshness. The freezer and refrigerator user set points remain unchanged while in this mode. If you unintentionally turn on Sabbath mode, the word “Sabbath” will light up on the display. Enter and exit Sabbath mode by pressing and holding °F/°C and SOUND at the same time for 3 seconds.

NOTE: You will be unable to dispense or change temperature set points in Sabbath mode. Your interior lighting and control panels will all be inactive in Sabbath mode.

External Dispenser Controls

The Dispenser UI is located above the external dispenser of the refrigerator.

Your refrigerator will turn off the vertical mullion heater and dispenser heater when Energy Saver is enabled.

■ To turn Energy Saver on, press and hold the Energy Saver

button for 3 seconds. The Energy Saver icon will blink 3 times and then remain lit as shown.

IMPORTANT: When Energy Saver is enabled and the LED is ON, the dispenser heater and vertical mullion heater will be turned off.

■ Press and hold ENERGY SAVER for 3 seconds again to turn

the heaters back on.

IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. Touch any control button to reactivate the display screen.

Additional Features

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the refrigerator door(s) or freezer drawer is open for 5 minutes and cooling is turned on. The alarm will repeat every 2 minutes. Close all doors and drawer to turn it off.

NOTE: To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, touch any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.

Lighting the Refrigerator

The refrigerator has an interior light that comes on any time the door is opened.

NOTE: The light is an LED which does not need to be replaced. If the LED does not illuminate when the door is opened, call Service to replace the light. See “Assistance or Service” in “Warranty” section for contact information.

Water and Ice Dispensers

2. Release the dispenser paddle for 5 seconds. Repeat steps

1 and 2 until water begins to ﬂow.

3. Once water begins to ﬂow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal (12 L) has been dispensed.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the Measured Fill feature. So, for optimum performance of your water dispenser, you must ﬁrst calibrate Measured Fill.

IMPORTANT:

■ Flush the water system before calibrating Measured Fill.

■ For best results, calibration should be performed when water

is not being used in the house.

1. Place a sturdy measuring cup (1-cup [237 mL] size) on the

dispenser tray centered in front of the ice/water dispenser paddle.

NOTE: Depending on your model, a measuring cup may be provided.

IMPORTANT:

■ Allow 3 hours for the refrigerator to cool down and chill water.

■ Allow 24 hours to produce the ﬁrst batch of ice. Discard the

ﬁrst 3 batches of ice produced.

■ The dispensing system will not operate if the left-hand

refrigerator door is open.

A. Water dispenser paddle B. Ice dispenser paddle

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water ﬁlter, ﬂush the water system.

Flushing the water dispensing system forces air from the water line and ﬁlter and prepares the water ﬁlter for use. Additional ﬂushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

A. Water dispenser paddle B. Ice dispenser paddle C. Measuring cup (1 cup)

Ensure that you do not have any Measured Fill preset selected.

2. Touch and hold the Measured Fill button for 3 seconds to

enter into Calibration mode. The Calibration and Measured Fill icons will illuminate and remain lit while the Measured Fill feature is being calibrated.

NOTE: You may touch MEASURED FILL to exit at any time in Calibration mode. The Calibration icon will disappear and the display will return to the Home screen.

3. Press and hold the water dispenser paddle, as needed, to

dispense water to the 1-cup ﬁll line in the measuring cup.

NOTE: If overﬁlling or spilling occurs, discard the water and

restart the calibration process.

4. When 1 cup of water has been correctly dispensed into

the measuring cup, touch MEASURED FILL to conﬁrm the calibration.

5. When Measured Fill calibration has been conﬁrmed, the

Calibration icon will disappear and the display will return to the home screen.

Save Favorite Fill

Household water pressure may affect the accuracy of the Favorite Fill feature. So, for optimum performance of your water dispenser, you must ﬁrst calibrate Measured Fill. (See Measured Fill section).

NOTE: Water will not be dispensed using the Favorite Fill feature unless your preferred Favorite Fill amount is saved ﬁrst.

IMPORTANT:

■ Flush the water system before Favorite Fill.

■ For best results, calibration should be performed when water

is not being used in the house.

1. Place a preferred-size cup on the dispenser tray centered in

front of the ice/water dispenser paddle.

2. Select either Favorite 1 or Favorite 2, and then touch and

hold the Favorite Fill button for 3 seconds to enter into Saving mode. The Favorite Fill icon will illuminate and remain lit while the Favorite Fill feature is being saved.

NOTE: You may touch FAVORITE FILL to exit at any time in Saving mode and the display will return to the Home screen.

3. Press and hold the water dispenser paddle, as needed, to

dispense water to the preferred-size cup. NOTE: If overﬁlling or spilling occurs, discard the water and

restart the saving process.

4. When the preferred amount of water has been correctly

dispensed into the cup, touch the Favorite Fill button to conﬁrm the favorite amount.

5. When Favorite Fill amount has been conﬁrmed, the display

will return to the home screen.

Dispensing

Touch CUBED ICE or CRUSHED ICE for your ice selection.

NOTES:

■ For crushed ice, cubes are crushed before being dispensed.

This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal and pieces of ice may vary in size.

■ When changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the ﬁrst cubes.

Dispensing Water

IMPORTANT:

■ Dispense at least 1 qt (1 L) of water every week to maintain a

fresh supply.

■ If the ﬂow of water from the dispenser decreases, it could be

caused by low water pressure.

■ With the water ﬁlter removed, dispense 1 cup (237 mL)

of water. If 1 cup (237 mL) of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

■ If it takes longer than 8 seconds to dispense 1 cup

(237 mL) of water, the water pressure to the refrigerator is lower than recommended. See “Water Supply Requirements” and “Troubleshooting” sections for suggestions.

To Dispense Water — Standard:

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing. NOTE: The Dispense Water button does not enable standard

dispensing. It only functions in Measured Fill mode.

To Dispense Water — Measured Fill:

Measured Fill allows you to dispense a speciﬁed amount of water with the touch of a few buttons.

1. Put a sturdy glass under waterspout. Touch MEASURED FILL

to activate. NOTE: The amount of water you select will be dispensed.

Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

2. Touch MEASURED FILL to turn on, then touch to select

8 oz (0.2 L), 16 oz (0.5 L), or 24 oz (0.7 L). Touch the fourth time to exit Measured Fill display.

3. Touch DISPENSE WATER (center button) or press paddle and

the selected amount of water will be dispensed.

NOTES:

■ The Measured Fill dispenser will automatically time out after

1 minute of inactivity.

■ You can reﬁll several glasses with the same measurement

by continuing to touch DISPENSE WATER (center button) after each glass ﬁll.

Measured Fill options are listed in the following chart:

Units

Ounces 8 16 24

Cups 1 2 3 Liters 0.2 0.5 0.7

NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup) are not the same size as a measuring cup (8 oz [237 mL]). You may need to recalibrate Measured Fill to underﬁll or to avoid unintentionally overﬁlling coffee cups.

4. Dispense water. NOTE: While dispensing water, the ﬂow of water will

automatically stop once the desired volume has been dispensed.

■ Press a sturdy glass against the dispenser paddle below

the waterspout.

■ Place the glass below the waterspout and touch

DISPENSE WATER for hands-free dispensing.

5. To pause dispensing before the selected volume has been dispensed, touch DISPENSE WATER a second time or touch the water dispenser paddle. Touch DISPENSE WATER or paddle again to resume dispensing remaining amount.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6. To select a new volume or start dispensing the same volume again, you must ﬁrst ﬁnish dispensing the selected volume or turn off the Measured Fill feature (either by waiting 1 minute so it will automatically turn off or by touching CUBED ICE or CRUSHED ICE to manually turn it off), and then select Measured Fill again.

To Dispense Water — Favorite Fill:

Favorite Fill allows you to dispense a preferred amount of water with the touch of a few buttons.

1. Put a sturdy glass under waterspout. Touch FAVORITE FILL to activate.

NOTE: The amount of water you select will be dispensed. Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

2. Touch FAVORITE FILL to turn on, then touch to select

Favorite 1 or Favorite 2. Touch the third time to exit Favorite Fill display.

3. Touch DISPENSE WATER (center button) or press paddle and

the selected amount of water will be dispensed.

NOTES:

■ The Favorite Fill dispenser will automatically time out after

1 minute of inactivity.

■ You can reﬁll several glasses with the same measurement by

continuing to touch DISPENSE WATER (center button) after each glass ﬁll.

4. Dispense water. NOTE: While dispensing water, the ﬂow of water will

automatically stop once the desired volume has been dispensed.

■ Press a sturdy glass against the dispenser paddle below

the waterspout.

■ Place the glass below the waterspout and touch

DISPENSE WATER for hands-free dispensing.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6. To select a new volume or start dispensing the same volume again, you must ﬁrst ﬁnish dispensing the selected volume or turn off the Favorite Fill feature (either by waiting 1 minute so it will automatically turn off or by touching CUBED ICE or CRUSHED ICE to manually turn it off), and then select Favorite Fill again.

WARNING

Cut Hazard Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

2. Press a sturdy glass against the dispenser paddle. Hold the

glass close to the dispenser opening, so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the paddle to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for several seconds after

removing the glass from the dispenser paddle. The dispenser may continue to make noise for a few seconds after dispensing.

The Dispenser Drip Tray

The drip tray can be removed to carry to the sink to empty or clean.

■ Lift up on the front edge of the tray and pull forward to

remove.

■ The drip tray can also slide out to assist in Measured/Favorite

Fill.

The Ice Dispenser

IMPORTANT:

■ If the ice cubes are hollow or have an irregular shape, it

could be because of low water pressure. See “Water Supply Requirements” section.

■ Ice travels from the ice storage bin through the dispenser

chute to the dispenser. To turn off the ice maker, see “Ice Maker and Storage Bin” section.

■ The dispenser may continue to make noise and ice may

continue to dispense for several seconds after releasing the dispenser button or paddle.

To Clean the Ice Dispenser Chute:

Humidity causes ice to naturally clump together. Ice particles can build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty the ice storage bin and clean the ice delivery chute, the ice storage bin, and the area beneath the storage bin every 2 weeks.

■ If necessary, remove the ice clogging the storage bin and

delivery chute using a plastic utensil.

■ Clean the ice delivery chute and the bottom of the ice storage

bin using a warm, damp cloth, and then dry thoroughly.

To Dispense Ice: Paddle Dispensing

1. Select the desired type of ice by pressing CUBED ICE or

CRUSHED ICE.

The Dispenser Light

1. When you use the dispenser, the light will automatically

turn on.

2. The dispenser light also serves as an automatic nightlight.

Once the ambient light in the room is reduced, the auto sensor will cause the dispenser light to illuminate.

The Dispenser Lock

The dispenser can be locked for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator or the dispenser light. It simply deactivates the controls and dispenser levers. To turn off the ice maker, see “Ice Maker and Storage Bin” section.

■ Touch and hold CUBED ICE for 3 seconds to lock the

dispenser.

■ Touch and hold CUBED ICE for 3 seconds to unlock the

dispenser.

■ The display screen indicates when the dispenser is locked.

Ice Maker and Storage Bin

IMPORTANT: To avoid low ice production and poor quality ice, ﬂush the water system before turning on the ice maker. See “Water Dispenser” section.

■ Following installation, allow 24 hours to produce the ﬁrst

batch of ice. Discard the ﬁrst 3 batches of ice produced. Allow 2 to 3 days to ﬁll the ice storage bin.

■ The quality of your ice will be only as good as the quality

of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well-maintained.

■ If the ice in the storage bin clumps together, break up ice

using a plastic utensil and discard ice. Do not use anything sharp to break up the ice. This can cause damage to the ice bin and the dispenser mechanism.

■ Do not store anything in the ice storage bin.

Ice Maker in the Refrigerator

The ice maker is located on the left door behind the bins. Ice cubes are ejected into the ice storage bin located on the lefthand refrigerator door.

Turn the Ice Maker On/Off

1. Push up on the latch on the left-hand side of the ice

compartment to open the door.

3. Close the ice compartment door.

Remove and Replace the Ice Storage Bin

■ Remove the ice storage bin by inserting your ﬁngers into the

hole at the base of the bin and pulling the latch to release the bin from the compartment. Lift the storage bin up and pull it straight out.

■ Replace the storage bin inside the ice compartment and push

down to make sure it is ﬁrmly in place.

Ice Production Rate

■ The ice maker should produce approximately 3 lbs (1.4 kg)

of ice per day under normal operation.

■ To increase ice production, select the “Fast Ice” feature from

the control panel. See “Using the Controls” section.

2. Turn on the ice maker by moving the switch to the On (I)

position.

NOTES:

■ To manually turn off the ice maker, move the control to the

Off (O) position.

■ Your ice maker has an automatic shutoff. The sensor will

automatically stop ice production if the storage bin is full, if the door is open, or the storage bin is removed. The control will remain in the On (up) position.

Shelves, Bins, and Drawers

Slide-Away Split Shelf

Some shelves will tuck away to create room for taller objects.

1. To retract the front section of the shelf, push the adjustable

portion of the shelf as far back as needed toward the rear of the refrigerator.

2. Extend the front glass and front trim of the shelf by pulling the

retracted portion of the shelf outward until it is fully extended.

Wine Rack and/or Under Shelf Storage Pan

Under one shelf, there are brackets installed to the supports (one bracket on each support). The wine rack or under-shelf storage rests in these brackets.

To remove and replace the wine rack or pan:

1. Remove the wine rack/pan by lifting it up off the brackets.

Press the right-hand side of the rack inward until it is free of its bracket. Lower the right-hand side slightly and disengage the left-hand side from its bracket.

2. Replace the wine rack/pan by inserting the left-hand side into

its bracket. Press inward on the right-hand side until it will slide past the bracket edge and set it into its bracket.

NOTE: Under shelf storage pan utilizes typically empty space beneath the shelf to create a prep zone ideal for doughs, desserts, casseroles, or marinating meats. The slide-out pan is oven and dishwasher safe and easily transitions from fridge to oven.

Important information to know about glass shelves and covers:

Shelves and Shelf Frames

The shelves in your refrigerator are adjustable to meet your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to ﬁt different heights of items will make ﬁnding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open and save energy.

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

1. Carefully lift the shelf off the shelf mounts and turn the ﬂipper

to the desired orientation.

2. Repeat for remaining shelf mounts.

3. Apply pressure to the top of the shelf to ensure the shelf is

properly seated on the shelf mounts.

To remove and replace shelves:

1. Make sure adjustable shelf mounts are in the lower position

before removing shelves. Also doors will need to be open at a 90˚ angle. If open wider, it will make it harder to remove the shelves.

2. Remove the middle shelf or top shelf by lifting it up and out

of the shelf supports. Then pull the shelf forward and tilt down to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

NOTE: Remove middle shelf ﬁrst before removing top shelf. Inﬁnity slide glass shelves should be pushed back in. When

tilted up, make sure glass does not slide to front.

3. Remove the bottom shelf by lifting it up and out of the

shelf supports. Then pull the shelf forward and tilt up to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

4. Replace the middle and top shelves by putting the shelf in the

refrigerator at an angle with the shelf front down. Lift the front of the shelf up and slide in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

5. Replace the bottom shelf by putting the shelf in the

refrigerator at an angle with the shelf up. Lift the front of the shelf down and slide in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

Shelves with under-shelf lighting (on some models)

By moving LED lighting to a new spot under the shelves, this leading-edge technology improves interior refrigerator lighting and aids in locating storage items.

Pull-Out Tray

To remove and replace the pull-out tray:

1. Pull the tray to the fully open position or when it stops.

2. Lift up and out of gliders toward the front of the refrigerator.

3. Replace the tray by placing it on the bottom tray guide and

pushing it past the tray stop into position.

FreshSeal™ Crisper Drawers

To remove and replace the drawers:

1. Grasp the handle at the bottom of the drawer and slide the

drawer straight out to the stop. Lift the drawer off the bottom guide.

2. Replace the drawer by placing it on the bottom drawer guide

and pushing it past the drawer stop into position.

To remove the crispers cover (can remove only if platter pocket is removed ﬁrst):

1. Remove the platter pocket ﬁrst.

2. Holding the glass insert ﬁrmly with one hand, press up in

center of glass insert until it rises above the plastic frame. Gently slide the glass insert forward to remove.

To replace crisper(s) cover(s):

1. Remove the crisper pan, platter pocket, and crisper glass

before removing the crisper.

2. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

3. Slide rear of glass insert into cover frame and lower front into

place.

Refrigerator Door Bins

The bins on your refrigerator door are adjustable to meet your individual storage needs.

FreshSeal™ Herb Bin

This is a cylinder with a FreshSeal™ to keep sensitive items like herbs fresh longer. The container allows water to be added to keep stems wet without covering leaves. It can be placed anywhere in the refrigerator and accommodates tall items like parsley, cilantro, and rosemary in addition to herbs like oregano, thyme, and mint.

Freezer Drawers

Audio Reference

Small Items Bin (on some models)

This drawer divider is not removable and is for small, delicate items. For storage ﬂexibility, the drawer bin can move forward and back, allowing you to store larger items in one section of the freezer.

Pizza Pocket

Space at the front of the drawer allows vertical storage of additional pizza boxes.

Third Tier

This shelf is not removable. To allow access, the third tier is able to move backward, allowing access to items in the area below.

Ice Bin (on some models)

Ice storage for second ice maker.

Tone Assignment

Tone Name Usage Examples

POWER ON Cooling system is turned on every time

the product is powered on. POWER OFF Cooling system is turned off. KEY PRESS User presses a valid button. INVALID (ERROR) User presses 2 or more valid buttons at

the same time. Count-down interruption

for press-and-hold buttons. User presses

pad when dispensing is not allowed. ENGAGE Acknowledgment of entry into any mode

or completion of dispensing. DISENGAGE Acknowledgment of exit from any mode ALERT Power Outage alert, Door Ajar alert

This table is for quick reference only. See corresponding sections for details. In case of inconsistency, section details will prevail.

A. Pizza pocket B. Third tier

REFRIGERATOR CARE

Cleaning

WARNING

Explosion Hazard Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

Exterior Cleaning

Please see the exterior cleaning information speciﬁc to your model.

Style 1 — Smooth Door IMPORTANT: Damage to smooth ﬁnish due to improper use of

cleaning products or using non-recommended cleaning products is not covered under the warranty. Sharp or blunt instruments will mark the ﬁnish.

DO USE DO NOT USE

✔ Soft, clean cloth ✘ Abrasive cloths

✘ Paper towels or newsprint ✘ Steel-wool pads

✔ Warm, soapy water with a

mild detergent

NOTE: Paper towels scratch and may dull the clear coat of the painted door. To avoid possible damage, use only soft, clean clothes to polish and wipe the doors.

Style 2 — Stainless Steel IMPORTANT:

■ Use recommended stainless steel cleaners and cloths

only. Damage to stainless steel ﬁnish due to improper use of cleaning products or using non-recommended cleaning products is not covered under the warranty.

■ Avoid exposing stainless steel appliances to caustic or

corrosive elements such as high-salt, high-moisture, or high-humidity environments. Damage due to exposure to these elements is not covered under the warranty.

✘ Abrasive powders or liquids ✘ Window sprays ✘ Ammonia ✘ Acidic or vinegar-based

cleaners

✘ Oven cleaners ✘ Flammable ﬂuids

DO USE DO NOT USE

✔ Soft, clean cloth ✘ Abrasive cloths

✘ Paper towels or newsprint ✘ Steel-wool pads

✔ Warm, soapy water with a

mild detergent

✔ For heavy soil, use ONLY

a stainless steel cleaner designed for appliances. To order the cleaner, see “Accessories” section.

Style 3 — Fingerprint-Resistant Stainless and Fingerprint-Resistant Black Stainless

IMPORTANT:

■ Avoid exposing stainless steel appliances to caustic or

corrosive elements such as high-salt, high-moisture, or high-humidity environments. Damage due to exposure to these elements is not covered under the warranty.

DO USE DO NOT USE

✔ Soft, clean cloth ✘ Abrasive cloths

✔ Warm, soapy water with a

mild detergent

NOTES:

■ If unintentional contact does occur, clean plastic part with

a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

■ Just because a cleaner is a liquid does not mean it is

nonabrasive. Many liquid cleansers formulated to be gentle on tile and smooth surfaces still damage stainless steel.

■ Citric acid permanently discolors stainless steel. To avoid

damaging the ﬁnish of your stainless steel refrigerator:

Do not allow these substances to remain on the ﬁnish:

✘ Mustard ✘ Citrus-based sauces ✘ Tomato juice ✘ Citrus-based products ✘ Marinara sauce

✘ Abrasive powders or liquids ✘ Ammonia ✘ Citrus-based cleaners ✘ Acidic or vinegar-based

cleaners

✘ Oven cleaners ✘ Stainless steel cleaner is for

stainless steel parts only! Do not allow the stainless steel cleaner and polish to come into contact with any plastic parts such as the trim pieces, dispenser covers, or door gaskets.

✘ Paper towels or newsprint ✘ Steel-wool pads ✘ Abrasive powders or liquids ✘ Window sprays ✘ Ammonia ✘ Acidic or vinegar-based

cleaners

✘ Oven cleaners ✘ Flammable ﬂuids

Interior Cleaning

IMPORTANT: Refrigerator shelves with under-shelf, LED lighting

are not dishwasher safe.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, ﬂammable ﬂuids, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum products on plastic parts, interior and door liners, or gaskets.

3. Plug in refrigerator or reconnect power.

Condenser Cleaning

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty or there is signiﬁcant pet trafﬁc in the home, the condenser should be cleaned every 6 months to ensure maximum efﬁciency.

If you need to clean the condenser, please call for service.

Lights

The lights in both the refrigerator and freezer compartments are LEDs which do not need to be replaced. If the lights do not illuminate when the door or drawer is opened, call for assistance or service. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

■ Press the switch to OFF for the door ice maker.

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You Leave: NOTE: Put refrigerator in Showroom Mode while on Vacation.

See “Using the Controls” section.

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least 1 day

ahead of time.

■ When the last load of ice drops, press the switch to OFF

for display to be unlit on the top inside of the refrigerator, depending on your model.

3. Empty the ice bin.

4. Turn off the temperature controls. See “Using the Controls”

section.

5. Clean refrigerator, wipe it, and dry well.

6. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least 1 day

ahead of time.

■ Disconnect the water line from the back of the refrigerator.

■ When the last load of ice drops, press the switch to OFF

either on the ice maker or the control, depending on your model.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Unplug refrigerator.

5. Clean, wipe, and dry thoroughly.

6. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

7. Depending on the model, raise the front of the refrigerator

so it rolls more easily OR raise the leveling screws so they don’t scrape the ﬂoor. See “Adjust the Doors” or “Refrigerator Leveling and Door Closing” section.

8. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to the “Installation Instructions” section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

+ 86 hidden pages