KitchenAid KGRT507BBL1, KGRT507BAL3, KGRT507BAL2, KGRT507BAL1 Owner’s Manual

ruse and Care Guide
IKJtchen,_id"
FORTHEWAY IT'SMADE."
Table of Contents
A Note to You ................ 3
Range Safety .............. 4-7
Getting to Know
Your Range ................... 8
Using and Caring
for Your Cooktop ........ 12
Using and Caring
for Your Oven .............. 21
Using EASY CONVECT"
Conversion .................. 39
TO THE INSTALLER: PLEASE LEAVE THIS
INSTRUCTION BOOK WITH THE UNIT.
TO THE CONSUMER: PLEASE READ AND
KEEP THIS BOOK FOR FUTURE REFERENCE.
KITCHENAID®THERMAL-CONVECTIONTM
Gas Freestanding and Slide-ln Ranges
PART NO. 9751683 Rev. E
Using the Self-
Cleaning Cycle ............ 54
Troubleshooting ......... 58
Requesting Assistance or
Service ......................... 61
Index ............................ 62
Warranty ...................... 64
1-800-422-1230
Call us with questions or comments.
Models:KGRT507B KGST307B _/'
- ble of Contents
A Note to You ............................................ 3
Range Safety .......................................... 4-7
Getting to Know Your Range .................... 8
Feature locations .................................. 8
The oven vent ..................................... 10
The storage drawer ............................. 10
The anti-tip bracket ............................. 11
Using and Caring for Your Cooktop ....... 12
Using the surface burners ................... 12
Energy saving tips .............................. 15
Cookware tips ..................................... 15
Caring for your cooktop ....................... 16
Using and replacing the
surface light........................................ 19
Using and Caring for Your Oven ............. 21
Using the electronicoven control......... 21
Oven settings ..................................... 24
Settingthe clock ................................. 25
Using the timer ................................... 26
Baking or convection baking ............... 27
Roasting ............................................. 29
Cooking tips ........................................ 30
Adjusting oven temperature ................ 33
Using the temperature probe ............... 34
Using CONVECT FULL MEAL ............ 37
Using EASY CONVECT TM
Conversion ......................................... 39
Broiling ............................................... 41
Convection broiling ............................. 43
13medcooking .................................... 46
Dehydrating ........................................ 49
Raising (proofing) bread ...................... 51
Cleaning your oven and controls ......... 52
Using and replacing the oven light(s)... 53
Using the Self-Cleaning Cycle ................ 54
Before you start .................................. 54
Before settingthe controls................... 55
Settingthe controls ............................. 55
For best cleaning results ..................... 57
How the cycle works ........................... 57
Troubleshooting ...................................... 58
Requesting Assistance or Service ......... 61
Index ........................................................ 62
Warranty .................................................. 64
Note to You
Thankyou for buying a KITCHENAID ®appliance!
KitchenAid designs the best tools for the most important room in your house. To ensure that you enjoy many years of trouble-free operation, we developed this Use
and Care Guide. It contains valuable information concerning how to operate and maintain your new appliance properly and safely. Please read it carefully.
Also, please complete and mail the enclosed Product Registration Card.
Please record your model's information.
Whenever you call our Consumer Assistance Center at 1-800-422-1230 or request service for your appliance, you need to know your
complete model number and serial number. You can find this information on the model
and serial number plate (see diagrams on pages 8 and 9 for location of plate).
Please also record the purchase information.
NOTE: You must provide proof of purchase or installation date for in-warranty service. Phone
Keep this book ond the soles slip together in a safe place for future reference.
Model Number
Serial Number
Purchase/ Installation Date
Builder/Dealer Name
Address
3
. nge Safety
Your safety is important to us.
This guide contains safety symbols and statements. Please pay special attention to
these symbols and follow any instructions given. Here is a brief explanation of the use
of the symbol.
Tip Over Hazard Connect anti-tip bracket to the range. Reconnect anti-Up bracket, if the range is moved.
Do not push down on the open oven door. Follow the Installation Instructions.
Do not let children climb onto the oven door. Failure to follow these instructions can result in death, burns,
or other injury.
This symbol alerts you to hazards such as
fire, electrical shock, or other injuries.
IMPORTANT SAFETYINSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Gas ranges have been thoroughly tested for safe and efficient operation. However, as with any appliance, there are specific installation and safety precautions which must be followed
to ensure safe and satisfactory operation.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,
personal injury or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
4
nge Safety
General
Install or locate the range only in accordance with the provided Installa-
tion Instructions. The range must be
installed by a qualified installer. The range must be properly connected to
the proper gas supply and checked for
leaks. The range must also be properly
connected to electrical supply and grounded.
Gas fuels and their use in appliances could cause minor exposures to ben- zene, formaldehyde, carbon monoxide,
and soot, primarily from incomplete combustion. Significant exposure to these substances could cause cancer or
reproductive harm. Properly adjusted
burners with a blue, rather than a yellow, flame will minimize incomplete
combustion. Venting with a hood or an open window will further minimize
exposure.
oWARNING: To reduce the risk of tipping
the appliance, the appliance must be secured by a properly installed anti-tip
bracket. To check if the bracket is
installed properly, see "The anti-tip
bracket" on page 11.
CAUTION: Do not store things children might want above the range. Children
could be burned or injured while climb-
ing on it.
Do not leave children alone or unat-
tended in area where the range is in use. They should never be allowed to -
sit or stand on any part of the range. They could be burned or injured.
Do not operate the range if it is dam-
aged or not working properly.
Do not use the range for warming or
heating the room. Persons could be burned or injured, or a fire could start.
Do not attempt to light the oven burner during a power failure. Personal injury
could result. Reset oven controls to the off position in the event of a power failure.
Use the range only for its intended use as described in this manual.
Do not touch surface burners, areas near burners, or interior surfaces of oven. Areas near surface burners and interior
surfaces of an oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other flam- mable materials contact surface burners,
areas near burners, or interior surfaces of oven until they have had sufficient time to
cool. Other surfaces of the range, such as
the oven vent opening, the surface near the vent opening, the cooktop, and the
oven door and window, could also become hot enough to cause burns.
Do not wear loose or hanging garments when using the range. They could ignite if
they touch an open flame and you could
be burned.
continued on next page
5
. nge Safety
Use only dry pot holders. Moist or damp pot holders on hot surfaces could result
in burns from steam. Do not let pot holder touch an open flame. Do not use
a towel or bulky cloth for a pot holder. It could catch on fire.
Keep range vents unobstructed.
Do not heat unopened containers. They
could explode. The hot contents could cause burns and container particles
could cause injury.
Use only cookware approved for oven
use. Follow cookware manufacturer's instructions, especially when using
glass or plastic cookware.
Do not store flammable materials on or
near the range. The fumes could create
an explosion and/or fire hazard.
Do not use the oven for storage.
Do not use aluminum foil to line area around surface burner, oven bottom, or any other part of the range. Use
aluminum foil only as recommended in this manual.
Do not repair or replace any part of the
range unless specifically recommended in this manual. All other servicing should
be referred to a qualified technician.
Any additions, changes, or conversions
required in order for this appliance to
satisfactorily meet the application needs
must be made by a KitchenAid servicer
or qualified agency.
Disconnect the electrical supplyand the gas supply at the shutoff valve near
range before servicing the range.
When using the cooktop
Make sure the cookware you use is large enough to contain food and avoid boilovers and spillovers. Heavy splatter-
ing or spillovers left on a cooktop could ignite and burn you. Pan size is espe-
cially important in deep fat frying.
Check to be sure glass cookware is safe for use on the range. Only certain
types of glass, glass-ceramic, ceramic, earthenware, or other glazed cookware
are suitable for cooktops without breaking due to the sudden change
in temperature.
Never leave surface burners unattended at high heat settings. A boilover could
result and cause smoking and greasy spillovers that could ignite.
Turn pan handles inward, but not over other surface burners. This will help
reduce the chance of burns, igniting of
flammable materials, and spills due to
bumping of the pan.
Do not use decorative covers or trivets over the surface burners.
Grease is flammable. Do not allow
grease to collect around cooktop or in vent. Wipe spillovers immediately.
6
. nge Safety
Do not use water on grease fires. Never pick up a flaming pan. Smother flaming
pan on range by covering with a well- fitting lid, cookie sheet, or flat tray.
Flaming grease outside of pan can be extinguished with baking soda or, if
available, a multipurpose dry chemical or foam-type extinguisher.
Never use a match or other flame to look for a gas leak. Explosion and injury
could result.
Know where your main gas shutoff valve is located.
When using the oven
Always position oven rack(s) in desired location while oven is cool.
Use care when opening oven door. Let hot air or steam escape before removing
or replacing food.
Small amounts of formaldehyde and carbon monoxide are given off in the
Self-Cleaning cycle from fiberglass insulation and food decomposition. Significant exposure to these substances
could cause cancer or reproductive harm. Exposure can be minimized by
venting with a hood or open window and wiping out excess food spills prior
to self-cleaning.
- SAVE THESE INSTRUCTIONS -
Do not use oven cleaners. No commercial oven cleaner or oven liner protective
coating of any kind should be used in or around any part of the oven.
Before self-cleaning the oven, remove broiler pan, broiler grid, oven racks, and
other cookware. Do not use your oven to clean miscellaneous parts unless you
are instructed to do so in this Use and Care Guide.
Do not clean door gasket. It is essential for a good seal. Care should be taken
not to rub, damage, or move the gasket. Clean only parts recommended in this
Use and Care Guide.
ffing to Know Your Range
This section tells you what features your range has and where they are located. It also
discusses some convenience features that you should know about, but which are not needed to operate the range. Please review this information before using your range.
To help you find information on specific parts or features quickly, page references are included.
Feature locations
Model KGST307B
Vent guard piece
Surface burners (pp. 12 and 16)
Surface burner controls (pp. 13 and 18)
Anti-tip
(p. 11)
Model and serial number
(p. 3)
Removable storage
(containing broiler pan, grid, and
convection roasting rack) (p. 1O)
Surface burner controls
- Oven vent
(p. 1O)
Electronic oven
(p. 21)
Automatic
oven light
switch
(p. 53)
Broil burner
(not shown)
(p. 24)
(not shown)
(p. 24)
Left rear Left front Right front Right rear
control knob control knob control knob control knob (pp. 13 and 18) (pp. 13 and 18) (pp. 13 and 18) (pp. 13 and 18)
Model KGRT507B
Surface light
(p. 19)
Surface burners ------.
(pp. 12 and 16)
Surface burner
controls (pp. 13 and 18)
Anti-tip
(p. 11)
Model and serial number plate
(p. 3)
Removable storage drawer
(containing broiler pan, grid, and
convection roasting rack)
(p. 10)
I
__._tting to Know Your Range
vent
(p. 1O)
Electronic
oven control
(p. 21)
Automatic
oven light
switch
(p. 53)
Broil burner
(not shown)
(p. 24)
Bake burner
not shown)
(p. 24)
Surface burner controls
":¢
.\i ivJ/ "b
Left rear control knob
(pp. 13 and 18)
Left front Right front Right rear
control knob control knob control knob
(pp. 13 and 18) (pp. 13 and 18) (pp. 13 and 18)
, *"
9
Getting to Know Your Range
The oven vent
Hot air and moisture escape from the oven through a vent in the center rear of the
cooktop. Do not block the vent by using large pans or covers. Poor baking/roasting
and combustion can result.
The storage drawer
You can remove the storage drawer to make it easier to clean under the range and to
check for installation of the anti-tip bracket.
Use care when handling the drawer.
Burn Hazard
Use pot holders when touching items left near oven vent.
Failure to do so can result in burns.
Replacing the storage drawer:
Removing the storage drawer:
1. Empty drawer of any pots and pans
before removing drawer. Use recessed area on top edge of drawer to pull drawer
straight out to the first stop, Lift front and pull out to the second stop.
2, Lift back slightly and slide drawer all the
way out.
Drawer slide rail
1. Fit ends of drawer slide rails into the drawer guides on both sides of opening.
2. Lift drawer front and press in until metal
stops on drawer slide rails clear white stops on drawer guides. Lift drawer front
again to clear second stop and slide drawer closed.
10
Geffing to Know Your Range
The anti-tip bracket
The range will not tip during normal use. However, tipping can occur if you apply too much force or weight to the open door without the anti-tip bracket properly secured.
Tip Over Hazard
Connect anti-tip bracket to the range.
Reconnect anti-Up bracket, if the range is moved. Do not push down on the open oven door.
Follow the Installation Instructions. Do not let children climb onto the oven door.
Failure to follow these instructions can result in death, burns,
or other injury.
To verify the anti-tip bracket is engaged:
leveling foot
Rear
Remove the storage drawer.
(See page 10.)
Look to see ifthe anti-tip bracket is attached to floor with screws.
Make sure left rear leveling foot is positioned under the anti-tip bracket.
See Installation Instructions for further details. -
11
sing and Caring for Your
Cooktop
This section tells you how to operate the controls to the cooktop. It also discusses how the sealed gas burner cooktop works, and includes tips on how to cook with and
maintain the cooktop.
Using the surface burners
Your cooktop has sealed gas burners with an auto-reignition system. The sealed
burners spread the heat evenly across the bottom of the cookware and provide infinite
heat control. The auto-reignition system senses when a burner flame has gone out
and will automatically reignite that burner.
IMPORTANT: Your cooktop is factory-set for use with Natural Gas. If you wish to
use L.P. gas, an L.P. Gas Conversion Kit (Part No. 9752401) is available from your
KitchenAid dealer or authorized parts distributor. The conversion must be
done by a qualified service technician.
When to use the right rear and left front burners:
10,000 BTU burner
When to use the left rear and right front burners:
6,000 BTU burner
6,000 BTU burner
Use these burners for simmering or for cook- ing smaller quantities of food requiring small
cookware.
10,000 BTU burner
Use these burners for cooking large quanti-
ties of food, deep-fat frying, or cooking with
large cookware.
12
sing and Caring for Your Cooktop
Carbon Monoxide Poisoning Hazard
Do not operate with a yellow flame. Doing so can result in death,
heart attack, or convulsions.
How to use the surface burners:
_,? o o
1. Grasp the control knob.
2. Push down and turn to HI. The electric
spark ignitorwill ignite the gas flowing into the burner. When you hear a clicking
sound, you know that the ignitors are working. Gas isflowing as long as knob is
not set at OFF.
3. When the burner is lit, turn the control
knob to the desired flame setting. (See guide under "Burner heat settings"on
page 14.) You can turn the knobs to any
of the marked settings. The ignitor will turn off and the clicking will stop when the burner ignites.
NOTES:
The ignitors may click a number of times
before burner lights. This is normal.
All four burner ignitors will spark regard=
less of which burner you are using.
Visually check that the burner has lit. If
the burner does not ignite, listenfor the clicking sound. If you do not hear the
ignitor click, TURN THE BURNER OFF.
Check that the service cord is placed firmly in the wall receptacle. Check for a
tripped circuit breaker or blown fuse.
Check that the control knob is pressed completely down on valve shaft. If the spark
ignitor still fails to operate, call your nearest authorized KitchenAid servicer.
Proper grounding and polarity are neces-
sary for correct operation of the electric ignition system. If the wall receptacle does not provide correct polarity, the ignitorwill
become grounded and click every once in a while, even after the burner has ignited.
A qualified electrician should check the wall receptacle to see ifit is wired with
correct polarity.
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death, fire, or burns.
Burner heat seffings
Use correct burner heat settings (see page 14). If the heat setting is too high, it can:
Char bacon and cause curling.
Make eggs tough and crisp at the edges.
Toughen liver, fish, and seafood.
Scorch delicate sauces and custards.
Cause a boilover.
continued on next page
13
r{.]sing and Caring for Your Cooktop
Until you get used to the settings, use the following as a guide. For best results, start
cooking at the high setting; then turn the control knob down to continue cooking.
SETrlNG RECOMMENDED USE
HI
MED
LO
In case of a prolonged power failure
Surface burners can be manually lighted.
To start foods cooking.
To bring liquids to a boil.
To hold a rapid boil.
To fry chicken or pancakes.
For gravy, pudding, and icing.
To cook large amounts of vegetables.
To keep food warm until ready to serve.
1. Hold a lit match near a burner and turn the control knob to the HI position.
2. After the burner lights, turn the
control knob to the desired setting.
14
Explosion Hazard
Turn the burners off if a flame goes out while cooking, or if there is a
strong gas odor. Wait five minutes for the gas odor to disappear before relighting burner.
Do not let the burner flame extend beyond the edge of the pan.
Turn off all controls when not cooking. Failure to follow these instructions can result in death, explosion, fire,
or burns.
NOTE: Do not leave the cooktop unattended
when cooking during a power failure. The
auto-reignition feature of your cooktop will
not operate during a power failure.
sing and Caring for Your Cooktop
Energy saving tips
Although the energy used for cooking is usually a very small percentage of the total
energy used in the home, cooking energy can be used efficiently. Here are some tips
to help you save energy when using your cooking product:
=Use pans with flat bottoms, straight sides,
and tight-fitting lids.
Cookware tips
NOTE: For best results and greater fuel efficiency, use only flat-bottomed cook- ware in good condition.
The pan should have straight sides and a
tight-fitting lid.
Be sure pans do not tip, whether they are
full or empty.
Pans should be easy to clean. Check to be sure there are no crevices, rough
edges, or areas where food might collect.
Use cookware only as instructed in the
cookware's user instructions. This is very
important for glass cookware because some can be used only in the oven. Pans
marked as flameware can be used on surface burners.
Choose medium to heavy gauge (thick-
ness) pans that are fairly lightweight.
The pan material (metal or glass) affects
how fast heat transfers from the surface burner through the pan material and how
evenly heat spreads over the pan bottom.
Choose pans that provide the best cooking results.
Handles should be made of sturdy, heat-resistant material and be securely
attached to the pan.
Cook with a minimum of liquid or fat to help shorten cooking time.
Start food on higher heat settings, then set surface burner control on low to finish
cooking.
Turn on the surface burner only after placing filled pan on the burner.
NOTE: Do not leave empty cookware, or
cookware which has boiled dry, on a hot surface burner. The cookware could over-
heat and damage the cookware or surface burner.
Home canning information
The large diameter of most water-bath or pressure canners combined with high heat
settings for long periods of time can cause damage to the cooktop.
To protect your cooktop:
I Ce._'over I Pan
i
Burner
. Use a canner/pan which can be cen-
tered over the surface burner. Large diameter canners/pans, if not properly centered, trap heat and can cause
damage to the cooktop.
Do not place canner on two surface
burners at the same time. Too much heat will build up and will damage the cooktop.
Start with hot water. This reduces the
time the control isset on high. Reduce heat setting to lowest position needed to keep water boiling.
Refer to your canner manual for specific
instructions.
15
CUsing and Caring for Your Cooktop
Caring for your cooktop
Your cooktop is designed for ease of care. You can do most cleaning with items found
around the home. Cleaning your cooktop whenever spills or soiling occur will help to
keep it looking and operating like new.
NOTES:
Before cleaning make sure all controls are off and the cooktop is cool.
Do not obstruct the flow of combustion and ventilation air.
If knobs are removed while cleaning, be careful not to spill liquids through holes in
the control area.
Be careful not to allow moisture to collect in control area. Moisture could cause
ignitor switches to fail.
Surface burners
The burner caps should be routinely removed and cleaned. Always clean
burner caps after a spillover. Keeping the burner caps clean prevents improper ignition and an uneven flame.
For proper flow of gas and ignition of the
burner, DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS, OR ANY OTHER
MATERIAL TO ENTER THE GAS TUBE OPENING.
Occasionally check the burner flames for proper size and shape. A good flame is blue in color. If flames liftoff ports, are
yellow, or are noisywhen turned off, you may need to clean the burners.
NOTE: To check oven burner flames for proper size and shape, see the Installation
Instructions.
To clean burners and burner caps:
Burner cap
m
Ignitor
G.stube
__" ° (Poe,;iicne_
1. Lift the burner cap straight up from the burner base.
2. Clean burner cap with warm, soapy water and a sponge. For stubborn stains, clean
with a mildly abrasive plastic scrubbing pad and powdered cleanser. Do not clean
burner cap in dishwasher.
3. If the gas tube opening or the orifice, located inside the opening, has become
soiled or clogged, use a cotton swab or a soft cloth to clean the area.
4. If ports are clogged, clean with a straight pin. Do not enlarge or distort
port. Do not leave anything stuck in
the ports.
5. After cleaning the gas tube opening and ports, replace the burner cap. To replace
burner cap, make sure cap is properly aligned and leveled.
6. Check the burner after cleaning for
proper lighting.
16
_sing and Caring for Your Cooktop
Adjusting the height of top burner
flames
Carbon Monoxide Poisoning Hazard Do not operate with a yellow flame. Doing so can result in death,
heart attack, or convulsions.
The LO burner flame should be a steady blue flame approximately 1/4inch high. It can be adjusted using the adjustment screw in the center of the valve stem. The valve
stem is located directly underneath the control knob.
To adjust the flame height follow the
instructions below:
1. Remove the control knob. (If there is not an adjustment screw underneath the knob
the flame height is not adjustable.)
2. Hold the valve stem with a pair of pliers.
The screw is located in the center of the valve stem. Use a small flat head screw-
driver to turn the screw until the flame is the proper size.
3. Replace the control knob.
ment screw
t Valvestem
4. Test the flame by turning the control from "LO" to "HI," checking the flame at each
setting.
Low flame
High flame
LrLI LrLI Ln_l Ln_l
17
' sing and Caring for Your Cooktop
Do not store flammable materials such as gasoline near this appliance.
Doing so can result in death, explosion, fire, or burns.
Cleaning your cooktop
Explosion Hazard
PART WHAT TO USE
Control Sponge and warm,
knobs soapy water
Tempered Sponge and warm, glass soapy water
surface
OR
Paper towel and
spray glass cleaner
Surface Warm, soapy water burner and a mildly abrasive
grates plastic scrubbing pad
and/or powdered cleanser
Surface burners
and caps
HOW TO CLEAN
Turn knobs to OFF and pull straight away from control panel.
Wash, rinse, and dry thoroughly. Do not soak.
Do not use steel wool or abrasive cleansers. They may damage the finish of the knobs.
Replace knobs. Make sure all knobs point to OFF.
Remove grates.
Wash, wipe with clean water, and dry thoroughly.
Use nonabrasive, plastic scrubbing pad on heavily
soiled areas.
Do not use steel wool, abrasives, or harsh cleansers. They may damage the finish.
If you use soap or detergent solutions, wipe thoroughly to prevent filmy residue.
NOTE: When cleaning cooktop with knobs removed,
do not allow water to run down inside unit.
Replace grates.
Remove grates.
Wash the grates with a mildly abrasive plastic scrubbing pad and warm, soapy water. Rinse and
dry well. For stubborn stains, clean with a scrubbing pad and/or a powdered cleanser and water. Repeat these cleaning steps as needed.
For best cleaning and to avoid possible rusting of unfinished surfaces, do not clean in a dishwasher
or self-cleaning oven.
Replace grates.
See page 16 and above for cleaning instructions.
18
"Using and Caring for Your Cooktop
Using and replacing the surface light
(Model KGRT507B)
The surface light is in the backguard. It is controlled by the Surface Light Command
Pads on the control panel. The On Com- mand Pad turns on the light immediately and
keeps it on until you press OFF. The Night Command Pad will turn on the surface light automatically when the light in the room is
low enough to require a night light. When the night light comes on, it will also dim all
lights appearing on the display. Press OFF to turn off the regular surface light or press
NIGHT again to turn off the night light.
To turn on the surface light:
PRESS
Replacing the surface light:
1. Unplug appliance or disconnect at
main power supply.
2. Flip up the top of the backguard.
To turn off surface light:
PRESS 3. Pull up glass on front of backguard.
To turn on night light:
PRESS
!,_II:J_'_.Tei4fll[_J=illl
4. Grasp the fluorescent light tube at both ends. Turn the tube approximately 90°
"NIGHT LIGHT" shows on the display when the night light is on.
To turn off night light:
PRESS again
S_rlr}_J_.,_#if_e_Ti
in either direction until both ends come
out of the receptacles. Replace with a 20-watt cool-white fluorescent light tube.
continued on next page
19
_sing and Caring for Your Cooktop
5. If the surface light still does not work,
you may need to replace the starter. The starter is a knob-shaped part located on
the right side of the backguard, under the
light tube.
To remove and replace the starter, first
remove light tube. Push starter in and
turn approximately 90° counterclockwise.
Pull starter out of recessed area. You can
find replacement starters at stores that
sell fluorescent light tubes.
6. Replace glass and close the top panel. Plug in appliance or reconnect at main
power supply.
20
Loading...
+ 44 hidden pages