KitchenAid KGCS105G, KGCC566H, KGCT366G, KGCC505H, KGCS166G User Manual
...
min.
15" 13-3/4" 19" 15" 2-1/8" 2-7/8" 5-5/8"
(38.1 cm) (34.9 cm) (48.3 cm) (38.1 cm) (5.4 cm) (7.3 cm) (14.3 cm)
30" 29" 19" 30" 2-1/8" 2-7/8" 5-5/8"
(76.2 cm) (73.7 cm) (48.3 cm) (76.2 cm) (5.4 cm) (7.3 cm) (14.3 cm)
36" 35-1/4" 19" 36" 2-1/8" 2-7/8" 5-5/8"
(91.4 cm) (89.5 cm) (48.3 cm) (91.4 cm) (5.4 cm) (7.3 cm) (14.3 cm)
42" 42-3/4" 19" 42" 2-1/8" 2-7/8" 11-1/2"
(106.7 cm) (108.6 cm) (48.3 cm) (106.7 cm) (5.4 cm) (7.3 cm) (28.4 cm)
Gas Built-in Cooktop
®
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
KGCC505H
KGCC566H
KGCR055G
KGCS105G
KGCS127G
KGCS166G
KGCT055G
KGCT305G
KGCT365G
KGCT366G
KGCV566M
Gas supply: Cooktop is equipped for use with
NATURAL gas (except model KGCR055 - L.P. gas
only). Cooktop can be converted to L.P. gas. Gas
supply line of 3/4" rigid pipe to cooktop location. If
local codes permit, a new AGA or CSA designcertified, 4-5 foot (1.2-1.5 m) long, 1/2" or 3/4"
I.D., flexible metal appliance connector is
recommended for connecting cooktop to gas
supply line. Pressure regulator has 3/8" female
pipe threads. The supply line shall be equipped
with an approved shutoff valve.
Electrical: 120-volt, 60 Hz, AC-only, 15 amp.
electrical supply. Use copper wire only. A timedelay fuse or circuit breaker and separate circuit is
recommended.
Grommet is required for electrical cable or power
supply cord hole cut in a metal cabinet.
Minimum distance
to combustible
surface above
countertop
Cooktop width
Gounded outlet –
Locate within 24"
(61 cm) of right rear
corner of cutout.
Gas line opening –
Wall: anywhere 5" (12.7 cm) below
underside of countertop.
Cabinet floor: anywhere within 6" (15.2 cm)
of rear wall is recommended.
Do not seal cooktop
to countertop.
24" (61 cm) min. –
deep countertop is
required.
13" (33 cm)
recommended
upper cabinet
depth
See NOTE*
for minimum
clearances.
combustible area
above countertop
*
Note: 24" (61 cm) min. clearance if bottom of wood or metal
cabinet is protected by not less than 1/4" (0.6 cm) flame
retardant millboard covered with not less than No. 28 MSG sheet
steel, 0.015" (0.04 cm) stainless steel, or 0.024"(0.06 cm)
aluminum or 0.020" (0.05 cm) copper.
30" (76.2 cm) min. clearance between top of cooking platform
and bottom of unprotected wood or metal cabinet.
18" (45.7 cm) min.
clearance upper
cabinet to countertop
within minimum
clearances to cooktop
Illustration dimensions
Important note on base cabinet construction:
After making the countertop cutout, some
installations may require notching down the base
cabinet side walls to clear the burner box. To
avoid this modification, use a base cabinet having
sidewalls wider the cutout.
30" (76.2 cm)
36" (91.4 cm)
15"
(38.1 cm)
30"
(76.2 cm)
21"
(53.3 cm)
2-7/8"
(7.3 cm)
21"
(53.3 cm)
2-7/8"
(7.3 cm)
2-7/8"
(7.3 cm)
36"
(91.4 cm)
21"
(53.3 cm)
2-7/8"
(7.3 cm)
43"
(109.2 cm)
21"
(53.3 cm)
42" (106.7 cm)
15" (38.1 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 4455834 Rev. A
05-12-04
Loading...