Kitchenaid KGCU462VSS, KGCU467VSS, KGCU407VSS, KGCU463VSS, KGCU482VSS Dimension Guide

...

PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS

KGCU407V KGCU462V KGCU463V KGCU467V

KGCU482V KGCU483V KGCU484V

Type of Gas Natural Gas:

This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

This cooktop is factory-set for use with Natural gas. To convert to LP gas, see the Gas Conversion instructions provided in the package containing literature. The model/ serial rating plate located on the left underside of the cooktop burner base has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician. No attempt shall be made to convert the cooktop from the

gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas conversion kit provided with the cooktop and see the “Gas Conversions” section.

Electrical:

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this cooktop be provided.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10271686D

08/26/09

Commercial Style Gas Cooktop

LOCATION REQUIREMENTS

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base.

It is recommended that a 600 CFM or larger vent hood be installed above the cooktop.

It is not recommended that a microwave hood combination be mounted above the cooktop.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Page 1 of 2

A. 30" (76.2 cm) cooktop: 29

36" (90.4 cm) cooktop: 35 48" (121.9 cm) cooktop: 47

B. 36" (91.4 cm) long 3 prong grounding-type

power supply cord

⁵⁄₈

" (75.1 cm)

⁵⁄₈

" (90.4 cm)

⁵⁄₈

" (120.8 cm)

C. Model/serial rating plate (located on the

underside of the cooktop burner base)

D. Island trim or optional backguard

E. 27¾" (70.5 cm)

Side View of Cooktop

A. 27¾" (70.5 cm) B. 1¼" (3.2 cm)

⁷⁄₁₆

" (18.8 cm)

C. 7 D. Gas inlet is located 1

the cooktop burner base and 4 from left-hand side of the cooktop burner base.

⁷⁄₈

" (4.8 cm) from the back of

⁷⁄₈

" (12.4 cm) in

E. 22" (55.9 cm)

⁵⁄₈

" (9.2 cm)

F. 3

G. 1" (2.6 cm)

Commercial Style Gas Cooktop

CABINET REQUIREMENTS

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10271686D

08/26/09

Page 2 of 2

Gas and Electric Connection Locations

A. Grounded 3-prong outlet should be located on

left-hand side of the cutout 16" (40.6 cm) max. from enclosure sidewall

B. 10" (25.4 cm) min. clearance from countertop to

top of the outlet C. 14" (35.6 cm) countertop to the gas supply line D. Gas supply line should be located in this area on

rear or side walls, or the supply line can come up

through the floor.

NOTE: Solid side and bottom of cutout enclosure not shown.

A. See chart.

A**

B min.*

B. See chart.

C. See chart.

D. See chart.

E. See chart.

F. 18" (45.7 cm) min. clearance upper

cabinet to countertop

" (1.9 cm) back of cabinet cutout to gas

opening cutout

6⁷⁄₈

" (16.1 cm) gas opening cutout depth

12½

" (31.7 cm) gas opening cutout width

22¼

J. " (56.5 cm) cabinet cutout depth

K. 2" (5.1 cm) cabinet side to gas cutout

L. 6" (15.2 cm) min. distance on both sides of the

cooktop to the side wall or other combustible material above cooking surface

M. 24" (61.0 cm) cabinet depth

7¼

N. " (18.4 cm) cabinet depth to countertop O. Notch to be equal on both sides

P. 13" (33.0 cm) upper cabinet depth

Size Model A**

Cooktop Cutout to Back Wall

30" (76.2 cm) KGCU407 30" (76.2 cm) ) 30" (76.2 cm) or

36" (91.4 cm) KGCU462

KGCU463 KGCU467

48" (121.9 cm) KGCU482

KGCU483 KGCU484

1¾" (4.4 cm)**

1½" (3.8 cm)** 1¾" (4.4 cm) 1¾" (4.4 cm)

1½" (3.8 cm)** 1¾" (4.4 cm)** 1½" (3.8 cm)**

B* Cooktop to

Cabinet

42" (106.7 cm)

*NOTES: Dimension “B” can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is covered by not less than

0.25" (6.4 mm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel,

0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. If installing a range hood above the cooktop, follow the range hood instructions for dimensional clearances above the cooktop

surface.

**NOTE: If backwall is constructed of a combustible material and a backguard is not installed, a minimum clearance of dimension A +

6" (15.2 cm) is required for

48" (121.9 cm) cooktops and cooktops with a grill.

C Optional

Backguard

D Cabinet and

Countertop

E Countertop Only

Opening

30" (76.2 cm) 29¼" (74.3 cm)

29 (75.9 cm) for

⁷⁄₈"

zero clearance

36" (91.4 cm)

35¼" (89.5 cm)

36" (91.4 cm) or

⁷⁄₈"

35 (91.1 cm) for zero clearance

48" (121.9 cm)

47¼" (120.0 cm) 48" (121.9 cm) or

⁷⁄₈"

47 (121.6 cm) for zero clearance