How it Works
KitchenAid
Loading...
KBRP20ERSS01
Owner’s Manual
56 pgs8.91 Mb0
Use & Care Manual
56 pgs8.54 Mb0

KitchenAid KBRP20ERSS01, KBRP20ERSS00, KBRA22ERWH00, KBRA22ERSS00, KBRA22ERBL00 Owner’s Manual

...
®itchen_kid ®
BOTTOM-MOUNT REFRIGERATOR
iJ _:;_:i!!_i!i!iiii_:i_i!;Ci;iiiii_i_'_;!!¸(i__i:iiiiii_;:i!ii!ii_i!!_¸
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www.kitchenaid.com
In Canada, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca
P P P
REFRIGERATEUR SUPERPOSE
Table of Contents/Table des matieres ............................................................................. 2
12828134/2300262
TABLEOF CONTENTS
REFRIGERATOR SAFETY ............................................................. 3
Proper Disposal of Your Old Refrigerator .................................... 3
INSTALLATION INSTRUCTIONS .................................................. 4
Unpack the Refrigerator ............................................................... 4
Location Requirements ................................................................ 4
Electrical Requirements ............................................................... 5
Water Supply Requirements ........................................................ 5
Connect the Water Supply ........................................................... 6
Base Grille .................................................................................... 7
Refrigerator Door .......................................................................... 7
Freezer Drawer ............................................................................. 8
Adjust the Door .......................................................................... 12
Water System Preparation ......................................................... 12
Factory Trim Kit .......................................................................... 13
Normal Sounds .......................................................................... 14
REFRIGERATOR USE .................................................................. 15
Ensuring Proper Air Circulation .................................................. 15
Using the Controls ..................................................................... 15
Water Dispenser ......................................................................... 17
Water Filter Status Light ............................................................. 17
Water Filtration System .............................................................. 17
Ice Maker .................................................................................... 17
REFRIGERATOR FEATURES ...................................................... 18
Refrigerator Shelves ................................................................... 18
Crisper and Crisper Cover ......................................................... 18
Crisper Humidity Control ............................................................ 19
Temperature-Controlled Drawer ................................................ 19
Utility or Egg Bin......................................................................... 20
FREEZER FEATURES .................................................................. 20
Freezer Baskets .......................................................................... 20
DOOR FEATURES ........................................................................ 20
Door Retainer ............................................................................. 20
Door Bins .................................................................................... 20
Utility Compartment ................................................................... 20
REFRIGERATOR CARE ............................................................... 21
Cleaning ...................................................................................... 21
Changing the Light Bulb ............................................................. 21
Power Interruptions .................................................................... 22
Vacation and Moving Care ......................................................... 22
TROUBLESHOOTING .................................................................. 23
ASSISTANCE OR SERVICE ......................................................... 25
In the U.S.A................................................................................ 25
In Canada ................................................................................... 25
Accessories ................................................................................ 25
WATER FILTER CERTIFICATIONS ............................................. 26
PRODUCT DATA SHEETS ........................................................... 27
WARRANTY .................................................................................. 28
TABLE DES MATIERES
SI_CURIT¢: DU RC:FRIGC:RATEUR .............................................. 29
Mise au rebut de votre vieux refrigerateur ................................. 29
INSTRUCTIONS D'INSTALLATION ........................................... 30
Deballage du refrigerateur ......................................................... 30
Emplacement d'installation ........................................................ 30
Specifications electriques .......................................................... 31
Specifications de I'alimentation en eau ..................................... 31
Raccordement de la canalisation d'eau .................................... 32
Grille de la base.......................................................................... 33
Porte du rdrigerateur ................................................................. 33
Tiroir du congelateur .................................................................. 34
Ajustement de la porte ............................................................... 38
Preparation du syst_me d'eau ................................................... 38
Ensemble decoratif de I'usine .................................................... 39
Sons normaux ............................................................................ 40
UTILISATION DU RC:FRIGI_RATEUR .......................................... 41
Pour s'assurer d'une circulation d'air appropriee ..................... 41
Utilisation des commandes ........................................................ 41
Distributeur d'eau ....................................................................... 43
Temoins lumineux de I'etat du filtre a eau ................................. 44
Systeme de filtration d'eau interieur .......................................... 44
Machine a glagons ..................................................................... 44
CARACTI_RISTIQUES DU REFRIGERATEUR ........................... 45
Tablettes du refrigerateur ........................................................... 45
Bac & legumes et couvercle ....................................................... 45
Reglage de I'humidite darts le bac & legumes ........................... 46
Tiroir a temperature contr61ee.................................................... 46
Casier utilitaire ou oeufrier .......................................................... 47
CARACTI_RISTIQUES DU CONGELATEUR ............................... 47
Paniers de congelateur .............................................................. 47
CARACTC:RISTIQUES DE LA PORTE ......................................... 47
Dispositif de retenue de la porte ................................................ 47
Balconnets dans la porte ........................................................... 47
Compartiment utilitaire ............................................................... 48
ENTRETIEN DU REFRIGI_RATEUR ............................................ 48
Nettoyage ................................................................................... 48
Remplacement de I'ampoule d'eclairage .................................. 49
Pannes de courant ..................................................................... 49
Entretien avant les vacances ou Iors d'un dem6nagement .......49
DI_PANNAGE ................................................................................. 50
ASSISTANCE OU SERVICE ......................................................... 53
Accessoires ................................................................................ 53
FEUlLLES DE DONNEES SUR LE PRODUIT ............................. 54
GARANTIE ..................................................................................... 55
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
m Plug into a grounded 3 prong outlet. _, Use nonflammable cleaner. m Do not remove ground prong.
m Do not use an adapter. m Do not use an extension cord.
• Disconnect power before servicing. m Replace all parts and panels before operating.
mRemove doors from your old refrigerator.
SAVE THESE INSTRUCTIONS
_, Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
_, Use two or more people to move and install refrigerator. m Disconnect power before installing ice maker (on ice maker
kit ready models only).
_, Use a sturdy glass when dispensing ice or water (on some
models).
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." Ifyou are getting rid of your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."
• Properly dispose of packaging.
When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator
for cieaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.
Expmosion Hazard
Keep flammable materials and vapors, such as gasomine, away from refrigerator.
Faimureto do so can resumt in death, explosion, or fire.
• Your refrigerator is designed for indoor, household use only.
• To ensure proper ventilation for your refrigerator, allow for a 1/2"(1.25 cm) space at the top and behind the refrigerator.
• If your refrigerator has an ice maker, allow extra space at the back for the water line connections.
• When installing your refrigerator next to a fixed wall, leave 21/s'' (5.4 cm) minimum on each side (depending on your model) to allow for the door to swing open.
NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install the refrigerator in a location where the temperature will fall below 55°F (13°C).
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."
_mportant information to know about glass shemves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use specia! care when removing them to avoid impact from dropping.
2%" (5.4 cm)
Emectrical Shock Hazard
Pmuginto a grounded 3 prong outlet° Do not remove ground prong, Do not use an adapter,
Do not use an extension cord° Failure to follow these instructions can resumt in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord. NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) OFF and then
disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.
Read all directions before you begin. IMPORTANT:
• If you turn the refrigerator on before the water line is connected, turn the ice maker OFE
All installations must meet local plumbing code requirements. Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain above freezing.
TOOLS NEEDED: Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Flat-blade screwdriver, 7/16"and 1/2" open-end wrenches or two adjustable wrenches, 1/4"nut driver and drill bit, hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a %" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more easily.
Water Pressure
A cold water supply with water pressure of between 35 and 100 psi (241- 689 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 100 psi (241- 689 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 - 414 kPa):
• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill after heavy usage.
If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."
If you have questions about your water pressure, call a licensed, qualified plumber.
Connect to Water Line
Connect to Refrigerator
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
3. Find a 1/2"to 11/4'' (12.7 mm to 3.18 mm) vertical cold water pipe near the refrigerator.
IMPORTANT:
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.
4.
To determine the length of copper tubing you will need, measure from connection on lower right rear of refrigerator to water pipe. Add 7 ft (2.1 m) to allow for moving refrigerator for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5,
Using a grounded drill, drill a 1/4"hole in the cold water pipe you have selected.
..................... a
B C
D E
F
..........................e
A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut
E.Compression sleeve F. Shutoff valve
G. Packing nut
6. Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"drilled hole in the water
pipe and that rubber washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and
evenly so rubber washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if
soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.
7. Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end
with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing into a bucket or sink. Turn ON main water supply and flush out tubing until water is clear.
Turn OFF shutoff valve on the water pipe. Check for leaks. Coil copper tubing.
1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.
2. Create a service loop using extreme care to avoid kinks. Secure copper tubing to refrigerator cabinet with a "P" clamp.
@
o
C D
E
A. Copper tubing D.Compression sleeve B. "P" clamp E. Water valve inlet port C. Compression nut
3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.
Complete the Installation
Electrica_ Shock Hazard
P_ug into a grounded 3 prong outlet.
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can resuR in death, fire, or eiectrica_ shock,
Plug in refrigerator or reconnect power.
Replace Handles (Panel Series)
Remove the Base Grille
1. Grasp the grille with both hands.
2. Pull the grille toward you.
Replace the Base Grille
1. See the markings on the inside of the base grille for proper placement.
2. Align the grille mounting clips with the cabinet slots.
3. Push the grille firmly into the cabinet slots until it snaps into place.
Graphics are included later in this section.
Remove and Replace Handles (Architecf Series)
1. Using a ¾2" Allen wrench, loosen the two set screws located
on the side of each handle. See Graphics 2 and 4.
2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching handles.
3. To replace the handle, reverse the directions.
1. Make sure the bottom door cap is installed. See Graphic 5.
2. Align handle notches with metal mounting tabs on the side of the door. Slide the handle down until it locks.
3. Tap the top of the handle with a rubber mallet to ensure a snug fit.
4. Using a Phillips screwdriver, reinstall the top door cap.
Remove Door and Hinges
IMPORTANT:
• Remove food and any adjustable door bins or utility bins from doors.
• All graphics referenced in the following instructions are included later in this section after "Final Steps."
_6" Hex-Head Top Hinge Screw
TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench, #2 Phillips screwdriver, and a fiat-blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator door closed until you are ready to lift it free from the cabinet.
NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.
3. Remove the parts for the top hinge as shown in Top Hinge Graphic. Lift the refrigerator door free from the cabinet.
4. Remove the parts for the bottom hinge as shown in the Bottom Hinge Graphic.
Reverse Door (Architect _ Series}
Remove Handles (Panel Series}
IMPORTANT:
• Remove the door from refrigerator before removing handles.
• You must remove the handles to remove the decorator panels or to reverse the door swing.
1. Using a Phillips screwdriver, remove the top door cap. See Graphic 3.
2. Tap the bottom edge of the refrigerator door handle upward with a rubber mallet.
3. Handle will slide up approximately 3/4"(19.05 mm) and release from the door.
IMPORTANT: If you want to reverse your doors so they open from the opposite side, follow these steps. If you are not
reversing the doors, see "Replace Door and Hinges."
Door Stop Screw Door Handle Seal ScrewFront
Flat-Head Handle Screw
Cabinet
1. Remove the hinge screws from handle side and move them to opposite side. See Graphic 1-1.
2. Using a flat-blade screwdriver tip wrapped in masking tape, remove the cabinet hinge hole plugs from the cabinet top and move them to the opposite side hinge holes as shown in Graphic 1-2.
Cabinet Hinge Hole Plug
Refrigeratordoor
1. Removetherefrigeratorhandleassemblyincludingthe mountingpostsandscrews.Keepallpartstogether.See Graphic2.
2. Removethedoorhandlesealscrewfront.Movetoopposite sideofrefrigeratordoorasshowninGraphic5.
3. Removethedoorstopfromthebottomedgeofthe refrigeratordoor.Movetooppositesideofrefrigeratordoor asshowninGraphic3.
4. Attachthedoorhandlemountingpoststotheoppositeside ofthedoor.
5. Positionrefrigeratorhandleovermountingpostsasshownin Graphic2.Drivetwosetscrewsinthesidesofthehandle.
6. Tightenallscrews.Setasidethedooruntilthehingesand freezercompartmentdrawerareinplace.
Reverse Door (Panel Series}
IMPORTANT:
• If you want to reverse your door so it opens from the opposite side, follow these steps. If you are not reversing the door, see "Replace Door and Hinges."
You must first remove the handle from the panel series refrigerator door to reverse the door swing.
1.
Using a flat-blade screwdriver tip wrapped in masking tape, remove the cabinet hinge hole plugs and move them to the opposite side of the cabinet as shown in Graphic 1.
2. Remove the hinge screws. Move to the opposite side of cabinet. See Graphic 2.
3. Using a Phillips screwdriver, remove the door stop and door cap located on the bottom edge of the refrigerator compartment. See Graphic 5.
4. Using a Phillips screwdriver, remove the top door cap.
5. Remove 1/4"hex-head screws from top door extension. Reverse the top door extension so the notched corner turns in toward the interior of the door. See Graphic 3.
6. Remove the side door trim and handle trim by tapping the bottom edges upward with a soft rubber mallet. The trim will slide up and release from the door. See Graphic 4.
7. Replace the bottom door cap and install the door stop on opposite side of the door. See Graphic 5.
8. Using the alternate side door trim, shipped with the refrigerator, align notches on trim with metal mounting tabs on side of door. Slide the trim down until it locks into place. Tap the top of the trim with a rubber mallet to ensure snug fit.
9. Install handle by aligning handle notches with metal mounting tabs on side of door. Slide the handle down until it locks. Tap top of handle with rubber mallet to ensure snug fit.
10. Using a Phillips screwdriver, install the top door cap.
Replace Door and Hinges
NOTE: When reversing panel series door, use alternate top hinge
shipped with refrigerator.
1. Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.
2. Assemble the parts for the top hinge as shown in the Top Hinge Graphic. Do not tighten screws completely.
3. Line up the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.
Graphics are included later in this section.
Remove Drawer
IMPORTANT: Two people may be required to complete this
procedure.
1. Open the freezer drawer to full extension.
2. Remove all articles from baskets.
3. Pull the upper wire basket out to full extension and lift out to remove.
4. Lift lower basket straight up and out to remove.
Remove the basket cradles from the drawer rails. Push the snap attachments inward away from the drawer rails to
unlatch the basket cradles. Lift the basket cradles off of the drawer rails.
B
Final Steps
1. Check all holes to make sure that hole plugs and screws are
in place. Reinstall top hinge cover. See Top Hinge Graphic.
A. Cradle snap attachment B. Basket cradle
6. Lift the top of the freezer drawer front to disengage drawer rail hooks from drawer rails. Lift drawer out.
Replace Drawer
IMPORTANT: Two people may be required to complete this
procedure.
1. Pull both drawer rails out to full extension.
2. Locate the notches on the inside of each drawer rail. See Graphic 6-1.
3. While supporting the drawer front, hook the drawer supports into the notches on the inside of the drawer rails. Lower the
drawer front into its final position. See Graphic 6-2.
4. Place the basket cradles back on the drawer rails. Align the snap attachments with the slots on the drawer rails, and press each snap toward the rail until it clicks.
5. With drawer rails pulled out to full extension, set the lower basket straight down into the basket cradles.
6. Slide the upper basket into the molded drawer rail. Make sure the rear of the basket hooks behind the drawer rail stop.
Electrica_ Shock Hazard
P_ug into a grounded 3 prong outlet.
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or eiectrica_ shock,
2. Plug in refrigerator or reconnect power.
3. Return all removable door parts to doors and food to refrigerator.
Architect ®Series
A. Hinge Cover Screw B. Top Hinge Cover C. %_"Hex°Head Hinge Screws
D. Top Hinge
Bottom Hinge
A. Cabinet Hinge Hole Plugs
F'sp' 4
A. Hinge Screws
, "22"- _ .................. B
I "_ "_ ......... C
ZC
A. Shim B. Center Hinge
C. Hinge Screws
.......... A
A. %/' Set Screw
Front View Side View Q
A B
A. Door Stop Screws B. Door Stop
A
A. %2" Set Screw
!
#
/
Door Handle Seal Screw
Front
/
!
10
Panel Series
Top Hinge
i ........... B
A. s/16"Hex-Head Hinge Screws B. Top Hinge
Bottom Hinge
A. Cabinet Hinge Hole Plugs
A. Handle Trim B. Side Door Trim
A B
A. Bottom Door Cap B. Door Stop
11
Depending on your model, your refrigerator may have two
(Style 1) or four (Style 2) adjustable rollers located at the base of the refrigerator. If your refrigerator seems unsteady or you want the door to close easier, adjust the refrigerator's tilt using the
instructions below.
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
1. Move the refrigerator into its final location.
2. Remove the base grille. Grasp the grille firmly and pull it toward you.
3. Remove the bracket covers. Insert the eraser end of a pencil in the cover notch. Apply slight downward pressure to the notched side of the cover while swinging it off.
Style 2 - Front and rear leveling
A B B A
A. Front adjustment screw
B. Rear adjustment screw C. Stabilizing foot
Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both front adjustment screws to the right. It may take several more turns, and you should turn both adjustment
screws the same amount.
6. Lower the stabilizing foot by turning it clockwise until it is firmly against floor.
7. Turn the front adjustment screws counterclockwise to allow the full weight of the refrigerator to rest on the stabilizing feet.
8. Replace the bracket covers. Place each bracket cover into the outer edge, swing the cover toward the cabinet and snap it into place.
9. Replace the base grille.
4.
Using a screwdriver or %" hex driver, turn the roller adjustment screw(s) on each side to raise or lower that side of the refrigerator.
NOTE: Having someone push against the top of the refrigerator takes some weight off the adjustment screws and
rollers. This makes it easier to turn the screws.
• To raise, turn the roller adjustment screw to the right.
• To lower, turn the roller adjustment screw to the left. NOTE: It may take several turns of the roller adjustment
screw to adjust the tilt of the refrigerator.
Style 1 - Front leveling
Please read before using the water system. Immediately after installation, follow the steps below to make
sure that the water system is properly flushed. f. Turn off the ice maker by opening the freezer door and lifting
up the wire shutoff arm as shown.
Install the interior water filter. The interior water filter mounting bracket is located on the left side wall of the refrigerator
compartment.
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified
for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Remove blue bypass cap and retain for later use. Carefully remove the interior water filter from its
packaging. Remove the sealing label from the end of the filter and insert it into the filter head.
• Gently rotate the filter clockwise until it stops. Then snap
the filter cover closed.
12
A. Roller adjustment screw
B. Stabilizing foot
3=
Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Flushing the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of the dispenser.
4=
Inspect the filter system for water leaks. If you see water leaks, see the "Troubleshooting" section.
5.
Turn on the ice maker by opening the freezer door and lowering the wire shutoff arm as shown. Please refer to the "Ice Maker" section for further instructions on the operation of your ice maker.
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced.
{ : I t
There may be an occasion when you will need to remove the factory-installed trim kit, such as moving the refrigerator to a new
home or installing custom-made decorator panels. Please read all instructions carefully before removing the trim kit and decorator panels.
A
qq
...........
Replace the Door Panel
1. Replace the refrigerator door panel:
• Carefully slide the 1/4"(6.35 mm), maximum thickness,
decorator panel in grooves provided by bottom door cap and side trim.
• Slide the filler board into place behind the decorator
panel, if necessary.
2. Attach the handle and trim.
3. Reinstall the refrigerator door.
Remove and Replace Freezer Drawer Panel
NOTE: You do not need to remove the freezer drawer to remove
or replace the decorator panel.
1. Pull the freezer drawer out to access the handle screws.
2. Using a Phillips screwdriver, remove the handle screws and lift off the handle.
3. Slide the decorator panel and filler board up through handle opening.
4. Replace the decorator panels by reversing directions.
Care of Decorator Panels
1. Clean panels with stainless steel cleaner and polish or mild soap and water with a clean, soft, damp cloth.
2. Rinse panels thoroughly and blot dry using a dry, soft cloth or chamois.
NOTE: Do not use paper towels or cleaners which contain solvents such as ammonia. They can damage the surface of
the panels.
Install Custom Wood Panels
A. 2_" (6.35 cm) Clearance B. Raised decorator panel C. Raised drawer panel
Remove the Door Panel
IMPORTANT:
• Door must be removed from refrigerator before removing handle.
• Top trim must be removed from refrigerator before removing door panel.
1. Remove the refrigerator handle:
• Using a Phillips screwdriver, remove the top door cap.
• Tap the bottom edge of refrigerator door handle upward
with a rubber mallet.
• The handle will slide up approximately 3/4"(19.05 mm) and
release from door.
2. Remove the door panel:
• Slide out decorator panel and filler board.
• Store panel and filler board carefully to prevent
scratching.
If you plan to install custom wood decorator panels, you will need to create the panels yourself or consult your cabinetmaker or carpenter. See dimensional drawings for wood panel inserts.
Flat Panels:
You can create a custom flat panel a maximum of _/4"(6.35 mm) thick to replace your decorator panels. Flat wood panels less than _/4"(6.35 mm) thick are not recommended.
Raised Panels:
A raised panel design can be created by screwing or gluing wood panels to 1/4"(6.35 mm) backing or by using 3/4"(19.05 mm) stock with routed edges. Allow 2_A'' (6.35 cm) minimum clearance between raised edge of panel and handle.
Weight requirements for raised panel inserts:
• Refrigerator door panel should not exceed 30 Ibs (14 kg).
• Freezer drawer panels should not exceed 15 Ibs (7 kg) combined weight.
13
DimensionsforCustomWoodPanels
Dimensions for Routing Door Panel (Side View)
20cu.ft.Refrigeratordoor
355/8''
•_ (90.5 cm) -_
42"
(106.7 cm)
!
361/10''
(91.6 cm) _1
Y
23V4" (59.1 cm)
!
Dimensions for Routing Handle Side of Raised Door Panels (End View)
+
%" (6 ram) m_x. L
A rain, B
A. Handle B. Door panel
1/4" (6.35 mm) max.
1/2" Top
(1.3cm)
Center face
detail between I_-__
(9.5 rnm)
Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds and what may be making them.
• If your refrigerator is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.
Your refrigerator is designed to run more efficiently, to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.
• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.
• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.
• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.
• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may cause a popping noise.
• You may hear air being forced over the condenser by the condenser fan.
• You may hear water running into the drain pan during the defrost cycle.
--[-
rnin.
offsets
%" L
min. Bottom
--(6,35 mm) max.
14
REFRIGERATOR USE
i!i!;ii_i_iii_!:ii_:u dilliii_i_i!iii_i;!iiii:%_::_ii::_,¸_;i;!_:_ii_i:,_ii:_ii:¸_Ciliil_i:_::!__!_!iiilii_iii_ii:i:iii:_i:_;ii:_
In order to ensure proper temperatures, you need to permit
airflow between the refrigerator and freezer sections. As shown in the illustration, cool air enters the freezer section through vents in the rear and top. The air flows forward through the freezer section
and recirculates under the freezer floor. Cool air enters the
refrigerator section through the top, flows down and across
shelves to the doors and recirculates to return air vents at the
bottom.
The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream
is firm. If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not blocked before adjusting the controls. See "Ensuring Proper
Air Circulation."
To Turn Your Refrigerator Off/On:
• Press the freezer (+) touch pad repeatedly until "OFF" appears in the freezer display. Allow a few seconds for the refrigerator to shut off. Neither compartment will cool.
• Press either the refrigerator or freezer (-) touch pad to turn on the refrigerator.
Adjusting Controls
The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.
If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a guide.
Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented and temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.
The control center is located at the top front of the refrigerator
compartment.
Temperature Controls
For your convenience, your temperature controls are preset at
the factory. When you first install your refrigerator, make sure the
controls are still set to the recommended set points as shown.
Recommended Settings
0°F Recommended 38°F Recommended
Warmer
Colder @
FREEZER REFRIGERATOR
_ armer
Colder
IMPORTANT:
• When the power is on, the temperature display shows the actual temperature of the compartment.
• Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has
cooled completely, your food may spoil. NOTE: Adjusting the refrigerator and freezer temperature
controls to a colder than recommended setting will not cool the compartments any faster.
To Adjust Set Point Temperatures: The first touch of the (+) or (-) touch pad displays the current
temperature set point. The display will show the set point for approximately 3 seconds, and then return to the actual temperature.
• Press the (+) or (-) touch pads until the desired temperature set point is displayed.
NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a time. Wait 24 hours for the temperature to stabilize between adjustments.
38°F Recommended
Warmer
REFRiG_:RATOR
Colder
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm Adjust REFRIGERATOR
- Door opened often, large amount TEMPERATURE Control of food added or room
1o lower
temperature very warm FREEZER too warm/ice not made
fast enough
- Door opened often, or large
Adjust FREEZER TEMPERATURE Control
1o lower
amount of food added or very cold room temperature (can't cycle often enough)
- Heavy ice usage
15
CONDITION/REASON: ADJUSTMENT: REFRIGERATOR too cold Adjust REFRIGERATOR
- Controls not set correctly for TEMPERATURE Control your conditions 1° higher
FREEZER too cold
- Controls not set correctly for your conditions
Additional Control Center Features
Max Cool
The max cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.
• Press the Max Cool touch pad to set the freezer and refrigerator to the lowest temperature settings. Press the Max Cool touch pad again to return to the normal refrigerator set point.
NOTE: The Max Cool feature will automatically shut off in approximately 12 hours.
Adjust FREEZER TEMPERATURE Control
1ohigher
©
Max
Cool
Optimlce _ Feature
The Optimlce ®feature assists with temporary periods of heavy
ice use by increasing ice production.
• Press the Optimlce ®feature touch pad to set the freezer to the lowest temperature setting. Press the Optimlce ®feature touch pad again to return to the normal freezer set point.
NOTE: The Optimlce ®feature will automatically shut off in approximately 24 hours.
Power Outage
During a power outage, if the temperatures in the refrigerator and freezer compartments exceed normal operating temperatures, the highest temperature reached will be displayed.
• Press the Temp Alarm touch pad until the indicator light is lit, to turn on this feature. Press and hold Temp Alarm for 3 seconds until the indicator light goes off to turn off this
feature.
Warm Alarm
An alarm will sound repeatedly if the freezer or refrigerator compartment temperatures exceed normal operating temperatures for an hour or more.
The temperature displays will alternately show the current temperatures and the highest temperatures the compartments reached when the power was out.
• Press the Temp Alarm touch pad once to stop the audible alarm and alternating temperature displays. The Temp Alarm light will continue to flash until the refrigerator temperature
stabilizes.
O
Temp Alarm
Door Alarm
The Door Alarm feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes.
The chime will sound until the door is closed or Door Alarm is turned off.
• Press the Door Alarm touch pad to turn this feature on or off. The indicator light will be lit when the Door Alarm feature is
on,
©
Optimmce
Holiday Mode In Holiday Mode, the freezer will not automatically defrost as
often to conserve energy.
• Press the Holiday Mode touch pad until the indicator light is lit to turn on this feature. Press the Holiday Mode touch pad again or open the refrigerator door to turn off this feature.
NOTE: The refrigerator door may be opened within 1 hour of setting Holiday Mode without turning off the feature.
O
©
Holiday
Mode
Temp Alarm
The Temperature Alarm combines power outage and warm alarm features.
O
Door
Alarm
Water Filter Status Lights and Filter Reset (on some models)
See "Water Filter Status Lights."
User Preferences
The control center allows you to set user preferences, if desired.
Temperature Display (F_C)
This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius
Alarm (AL)
This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound.
OFF - You will not hear the alarm sound.
Sabbath Mode (SAB) IMPORTANT: This preference does not disable interior lights.
ON - All control panel lights will be disabled. OFF - All control panel lights will be enabled. NOTE: Press any touch pad on the control panel to restore the
control panel lights.
16
To Access the User Preferences Menu:
1. Press and hold the Door Alarm touch pad for 3 seconds. The preference name will appear in the Freezer display and the preference status (F or C) or (ON or OFF) will appear in the Refrigerator display.
2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator (+) or (-) touch pads to change the preference status,
3. Set your preferences by pressing and holding the Door Alarm touch pad for 3 seconds, or by shutting the refrigerator compartment door.
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
IMPORTANT:
• The water filter should be replaced when the status light is red (Replace) or earlier if the flow of water to your water dispenser or ice maker decreases noticeably.
• Air trapped in the system may cause water and the water filter to eject. Dispense water for 2 minutes before removing
the used water filter.
If you did not flush the water system when the refrigerator was
first installed, dispense water into a container until you draw and
discard 2 to 3 gal. (8 to 12 L) or for approximately 6 to 7 minutes after the water begins dispensing. The water you draw and discard rinses the pipes. Allow several hours for the refrigerator
to cool down and chill water.
Dispensing Water
1. Hold a container under the dispenser while pressing the button.
2. Release the button to stop dispensing.
NOTE: Dispense enough water every week to maintain a fresh supply.
Replacing the Water Filter
The water filter mounting bracket is located on the right side of the refrigerator compartment.
1. Turn the used water filter counterclockwise until it releases from the filter mounting bracket.
2. Drain water from the water filter into the sink, and discard the used water filter. Wipe up the excess water in the filter cover.
3. Remove the sealing label from the end of the new water filter and insert the water filter into the filter mounting bracket. Gently rotate the water filter clockwise until it stops, and snap
the filter cover closed.
4. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
5. Inspect the water filter system for leaks. Ifyou see water leaks, see "Troubleshooting."
{ : t
The water filter status light will help you know when to change the water filter. When the yellow (Order) light is on, it is almost time to change the water filter. When the red (Replace) light is on,
a new water filter should be installed. See "Water Filtration System."
After replacing the water filter, press and hold FILTER RESET for
3 seconds until the Order or Replace light turns off.
Order RepHace
©
FiHter
Reset
Using the Dispenser Without a Water Filter
You can use the water dispenser without a water filter, but your water will not be filtered. If you choose this option, replace the water filter with the blue bypass cap.
Turning the Ice Maker On/Off
NOTE: Do not force the wire shutoff arm up or down.
• To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.
17
Loading...
+ 39 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use