KitchenAid 9752397 Installation Instructions Manual

HOME APPLIANCES

A WARNING

ALL RANGES CAN TIP

INJURY TO PERSONS COULD RESULT

INSTALL ANTI-TIP DEVICE PACKED

WITH RANGE

SEE INSTALLATION INSTRUCTIONS

IMPORTANT: Read and save

these instructions.

IMPORTANT : Installer: Leave Installation Instructions

with the homeowner.

Homeowner: Keep Installation

Instructions and anti-tip bracket template for future reference.

Save Installation Instructions for local

electrical inspector’s use.

Part No. 9752397 Rev. C

30" (76.2

cm)

Sealed Burner m

Freestanding and

SlideGin Ranges

with self-cleaning thermal/convection oven

Before you start...

Cabinet opening dimensions

25” (63.5 cm) countertop depth (with or without backsplash) and 24” (61 cm) base cabinet depth,

36” (91.4 cm) countertop height

Your safety and the safely of others is

very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This

symbol

alerts you to hazards that can kill or hut-l you and others. All safety messages will be preceded by the safety alert symbol and the word “DANGER” or “WARNING”. These words mean:

Freestanding Range

to countertop

30” (76.2 cm) ial

///zff5$$

P-5

opening width opening width

You will be killed or seriously injured if you don’t follow instructions.

3”

17.6 cml

You can be killed or seriously injured if you don’t folloZ&uctions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

of range to side wall or other combustible material.

24” -rl ~‘1

#-if51 cm)

j (15.2,cm)l

Gas line opening can be located within this shaded area.

Wall receptacle should be located

,4 cm) within the 18” x 10”

(45.7 cm x 25.4 cm)

< shaded area.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

- Do Not store or use gasoline

or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHATTO DO IFYOU SMELL

GAS

Do Not try to light any

appliance.

Do Not touch any electrical

switch; Do Not use any phone in your building.

Immediately call your gas

supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your

gas supplier, call the fire department.

- Installation and service must

be performed by a qualified installer, service agency or the gas supplier.

2” (5.1 cm)-

7/E” (2.2 cm) min. required

.between cabinet

opening and door or hinge opening.

Slide-in Range

-13” (33&M max. upper / \cabinet depth

For minimum

18” i45.7 cm)

upper cabinet

30” (76.2 cm) cabinet

clearance to

to countertop

opening width

coc;,,m -

--op, see

‘..I

, _ , opening width

4” (10 2 cm) min R cleara’nce from doth

111 sides of range to side wall or other ‘I/ I combustible material.

/f /

IMPORTANT:

k- /

Rear vent must be

1R"

installed on all slide-in models for

Gas line opening should be located within this shaded are

proper ventilation. See Step 7.

floor gas line opening if directly below regulator

located within the 18” x 10” (45.7 x 25.4 cm)

Countertop opening dimensions that are shown

must be used. Given dimensions provide required

clearances. When installing a cooktop under existing cabinets

and the installation does not meet the minimum cabinet clearances, install a range hood above the cooktop to avoid burn hazards.

Read electrical and carpentry instructions.

Proper installation is your responsibility. A qualified technician must install this range. Make sure you have everything necessary for correct installation. It is the customer’s responsibility to make sure that the countertop has been properly prepared and that the installation clearances specified on the model/serial rating plate are met. The model/serial rating plate is located on the frame behind the drawer.

Check location where range will be installed. The range should be located for convenient use in the kitchen. Recessed installations must provide complete enclosure of the sides and rear of range.

ALL OPENINGS IN THE WALL OR FLOOR WHERE RANGE IS TO BE INSTALLED MUST

BE SEALED.

IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

shaded area.

718” (2.2 cm) min. required between

e cabinet opening and door or hinge

opening.

It is the customer’s responsibility: To contact a qualified electrical installer. To assure that the electrical installation is

adequate and in conformance with National Electrical Code, ANSUNFPA 70 - latest edition*, or CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition**, and all local codes and ordinances.

Note: This appliance is manufactured for use with Natural Gas. Conversion to L.P. Gas can be made using the kit included in your literature package.

Important: Observe all governing codes and ordinances.

Earthed/grounded electrical outlet is required. See “Electrical requirements,” Panel C.

Cabinet opening dimensions that are shown must be used.

Do Not pinch the power supply cord between the range and the wall.

Do Not seal range to side cabinets.

Copies of the standards listed may be obtained from:

*National Fire Protection Association

Batterymarch Park Quincy, Massachusetts 02269

* Canadian Standard Association

178 Rexdale Boulevard Etobicoke (Toronto), Ontario M9W lR3

Note: The metal chassis of the range MUST be earthed/grounded in order for the control panel to work. If the metal chassis of the range is not earthed/grounded, NO keypads will operate. Check with a qualified electrician if you are not sure the range is earthed/grounded.

‘** Note: 30” (76.2 cm) min. when bottom of wood or

metal cabinet is protected by not less than 114” (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015” (0.4 mm) stainless steel, 0.024” (0.6 mm) aluminum or 0.020” (0.5 mm) copper.

36” (91.4 cm) min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

Panel A

Slide-in ranges:

Tools needed for

countertop preparation

installation:

30-319”

(77.2 cm)

openmg\

___!_1AL

countertop opening.

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30-3/8” (77.2 cm), no countertop preparation is required.

Formed front-edged countertops: Must have molded edge shaved flat l/4” (0.64 cm) from each front corner of opening.

Tile countertops may need trim cut back l/4” (0.64 cm) from each front corner and/or rounded edge flattened.

Cooktop sides df raAge fit over edges of countertop opening.

If countertop opening width is greater than 30-3/8” (77.2 cm), adjust the l/4” (0.64 cm) dimension.

Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Oven must be level for satisfactory baking conditions.

measurina taoe

rhammer

le Ge&

’ 111

-/I/

i’

sarery

glasses

112” (1.3 cm)

Product dimensions

Freestanding Range

8-W

(21 Cl

1 -l/2”

(3.8, cm)

diameter .

router bit hand or electric drill

wood floor:

l/8” (0.3 cm) drill bit

concrete/ceramic floor:

3/16” (0.48 cm) carbide-tipped masonry drill bit

L.P. gas conversion

requires:

pin pick up (claw attachment) 5116” nut driver

Parts supplied for installation:

burner grates and caps

vent cap

L.P. conversion orifice spuds kit: 2 x #64 cook-top 2 x #69 cooktop 1 x #65 broil burner

(Bracket must be securely mdunted to sub-floor. Thickness of flooring may require longer screws to anchor the bracket

to sub-floor.)

Mobile home installation

The installation of this range must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280); or when such

standard is not applicable, the Standard for

Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI

A225.1/NFPA 501A*, or with local codes.

In Canada, the installation of this range must conform with the current standards CANESA-Z240 - latest edition*‘, or with local codes.

When this range is installed in a mobile home, it must

be secured to the floor during transit. Any method of

securing the range is adequate as long as it conforms to the standards listed above.

Copies of the standards listed may be obtained from:

National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269

* Canadian Standard Association

178 Rexdale Boulevard Etobicoke (Toronto), Ontario M9W lR3

IMPORTANT: Rear vent must be installed on all slide-in models for proper ventilation. See Step 7.

Panel

Anti-tip bracket:

The floor anti-tip bracket MUST be installed.To install the anti-tip bracket shipped with the range, see Panel D and the anti-tip bracket template.

with

+ 4 hidden pages

KitchenAid 9752397 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual