KitchenAid 9752179 Installation Instructions Manual

Installation Instructions

IMPORTANT:
Read and save
these instructions.

IMPORTANT:
Installer: Leave Installation Instructions with the

homeowner.

Homeowner: Keep Installation Instructions for future

reference.

Save Installation Instructions for local electrical

inspector's use.

30" (76.2 cm)
Electric Slide-in Range

with self-cleaning
thermal/convection oven

Part No.9752179

Accessories

• Horizontal Backguard
Part No. 9752090PW – White

9752090PT – Almond
9752090PB – Black

service...

Maintain the quality built into your
KitchenAid Appliance — call a KitchenAid-
authorized service company.

In the event that your KitchenAid appliance
should need service, call the KitchenAid
Consumer Assistance Center.A special
operator will tell you the name of your
nearest
KitchenAid-authorized service company.

KitchenAid Consumer Assistance Center:
English 1-800-461-5681
French 1-800-461-5703

Failure to follow this instruction could
result in serious injury.

Part No.9752179
© 1995 KitchenAid
® Registered Trademark of KitchenAid.

Prepared by KitchenAid, St. Joseph, Michigan 49085

Printed in Canada

®

®

HOME APPLIANCES

HOME APPLIANCES

WARNING

!

Injury Hazard
Injury from ranges tipping
could result.

See Installation Instructions.

Before you start...

Read electrical and carpentry
instructions.

Proper installation is your responsibility.A

qualified technician must install this range.
Make sure you have everything necessary
for correct installation. It is the customer’s
responsibility to make sure that the
countertop has been properly prepared and
that the installation clearances specified on
the model/serial rating plate are met.The
model/serial rating plate is located on the
frame behind the drawer.

Check location where range will be
installed.The range should be located for
convenient use in the kitchen.Recessed
installations must provide complete
enclosure of the sides and rear of range.

ALL OPENINGS IN THE WALL OR FLOOR
WHERE RANGE IS TO BE INSTALLED
MUST BE SEALED.

Cutout shown is for a 25-inch (63.5 cm)
countertop with a 24-inch (61 cm) base
cabinet and no backsplash. If countertop has
a backsplash, see “Countertop preparation.”

Cabinet construction: This appliance is
designed for use in a base cabinet with a
depth of 24 inches (61 cm).The maximum
depth for overhead cabinets is 13 inches
(33 cm). For the minimum vertical clearance
between the cooking surface and the
overhead cabinets, see Note.*** Overhead
cabinets installed at either side of the
appliance must be a minimum of 18 inches
(45.7 cm) above the cooking surface. The
minimum horizontal distance between the
overhead cabinets is 30 inches (76.2 cm).

7/8" (2.2 cm)
min. required
between
cutout and
cabinet door
or hinge.

Earthed outlet –
8" (20.3 cm) to
22" (55.9 cm) from
either cabinet,
7" (17.8 cm) max.
from floor.

Do Not pinch the
power supply cord
between the range
and the wall.

Do Not seal range
to side cabinets.

36" (91.4 cm)
countertop
height

30-3/8" (77.2 cm)
opening width

22-3/4" (57.8 cm)
opening depth

Cabinet opening dimensions

25" (63.5 cm) countertop
24" (61 cm) base cabinet

Countertop preparation

4" (10.2 cm) min.
clearance to side wall
or other combustible
material — both sides
of range.

***

Note: 24" (61 cm) min. when bottom
of wood or metal cabinet is protected
by not less than 1/4" (0.64 cm) flame
retardant millboard covered with not
less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024"
(0.6 mm) aluminum or 0.020" (0.5
mm) copper.

30" (76.2 cm) min. clearance between
the top of the cooking platform and
the bottom of an unprotected wood
or metal cabinet.

30" (76.2 cm) min.
cabinet opening width

1/2" (1.3 cm)
radius both
corners

Cabinet opening
dimensions that are

shown must be used.

The cooktop sides of the slide-in range fit
over the cutout edge of your countertop.

If you have a square finish (flat)
countertop and the opening width is 30­3/8" (77.2 cm), no countertop preparation

is required.
Formed front-edged countertops must

have molded edge shaved flat 1/4" (0.64
cm) from each front corner of opening.

Tile countertops may need trim cut back
1/4" (0.64 cm) from each front corner
and/or rounded edge flattened.

If countertop opening width is greater
than 30-3/8" (77.2 cm), adjust the 1/4"

(0.64 cm) dimension.
Countertop must be level. Place level on

countertop, first side to side; then front to
back. If countertop is not level, range will
not be level.Oven must be level for
satisfactory baking conditions.

Earthed-grounded
electrical outlet is

required.

Important: Observe
all governing codes
and ordinances.

For minimum
clearance to the top
of the cooktop, see
Note.

***

18" (45.7 cm)
upper cabinet
to countertop

13" (33 cm) max.

upper cabinet depth

Panel A

1-1/2"
(3.8 cm)

1"
(2.5
cm)

25-3/4"
(65.4 cm)
depth with
handle

When installed in a 24" (61 cm)
base cabinet with 25" (63.5 cm)
countertop — front of oven door
protrudes 1-7/8" (4.8 cm) beyond
base cabinet.

30-7/8"

(78.4 cm)

cooktop

width

36"

(91.4 cm)

countertop

height

Product dimensions

22-5/8"
(57.5 cm)

30" (76.2 cm)
range width

Mobile home installation

The installation of this range must conform to
the Manufactured Home Construction and
Safety Standards, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD,
Part 280); or when such standard is not
applicable, the Standard for Manufactured
Homes Installations (Manufactured Home
Sites, Communities and Setups), ANSI
A225.1/NFPA 501A, or with local codes*.

In Canada, the installation of this range must
conform with the current standards
CAN/CSA-Z240 — latest edition**, or with
local codes.

When this range is installed in a mobile home,
it must be secured to the floor during transit.
Any method of securing the range is
adequate as long as it conforms to the
standards listed above.

Four-wire power supply cord must be used in
a mobile home installation.The appliance
wiring will need to be revised.

Copies of the standards listed may be obtained from:

*

National Fire Protection Association
Batterymarch Park
Quincy,Massachusetts 02269

**

Canadian Standard Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario M

9W 1R3

Formed or tiled countertop
trimmed 1/4" (0.64 cm)
back at front corners of
countertop opening.

30-7/8"

(78.4 cm)

1/4"
(0.64 cm)

30-3/8"

(77.2 cm)

opening

width

Cooktop sides
of range fit
over edges of
countertop
opening.

WARNING

!

Injury Hazard

To eliminate the risk of burns or fire,
avoid installing cabinet storage above
the cooking surface. If cabinets are
already installed, reduce the hazard of
reaching over a heated cooking surface
by installing a range hood.The range
hood should extend a minimum of 5
inches out from the bottom front of the
cabinets.

Reaching over a heated cooking
surface could result in a serious burn
or other personal injury.

Note: The metal chassis of the range MUST

be earth-grounded in order for the control
panel to work. If the metal chassis of the
range is not earth-grounded, NO keypads will
operate.Check with a qualified electrician if
you are in doubt as to whether the metal
chassis of range is earth-grounded.

22-5/8"

(57.5 cm)

cooktop depth

Tools needed for
installation:

level

flat-blade
screwdriver or
5/16"nut driver

pliers

hammer

wrench

measuring tape
or ruler

Phillips
screwdriver

3/8"
ratchet

Panel B

Now start...

With range in kitchen.

Put on safety glasses.Remove

shipping materials, tape and
protective film from range.Keep cardboard
bottom and shipping base under range.
Remove oven racks and parts package
from inside oven.

4.

3.

Injury Hazard

Because of the weight and size of the
range, two or more people are needed
to move and safely install it.

Failure to do so could result in
serious injury.

WARNING

!

1.

Take 4 cardboard
corners from the
carton. Stack one
cardboard corner
on top of another.
Repeat with the
other two corners.
Place corners
lengthwise on the
floor in back of range so corners will support
outer side edges of range as shown.

Firmly grasp the range and gently

lay it on its back on the cardboard

corners.

Pull cardboard bottom and shipping

base firmly to remove.

cardboard
corners

spacers

2.

5.

6.

Use an adjustable
wrench to loosen the
leveling legs 1-1/2
turns.

Place cardboard or hardboard in
front of range. Stand range back up

onto cardboard or hardboard.

safety
glasses

Place
rack in
oven.Place level
on rack, first side to side; then front
to back. If range is not level, slide range out
of position and use a
3/8" (95 mm) ratchet to adjust the leveling
legs up or down.Then slide range back into
position.

NOTE: Oven must be level for satisfactory
baking conditions.

Press on front
of storage
drawer and
release to open. Pull drawer open
to first stop position. Lift front of drawer to
clear white wheels in drawer guides.
Remove drawer and set it aside on a
protected surface.

Move range close to cabinet

opening. Make sure all controls are
in the “OFF” position. Make electrical
connection. If the factory installed power
supply cord cannot be plugged into your
outlet, have a qualified electrician install a
matching earthed outlet. Do Not modify the
power supply cord.

Remove cardboard or hardboard

from under range. Carefully move
range into final position.

10.

Before moving range, slide it onto
cardboard or hardboard.

7.

8.

9.

11.

Insert storage drawer into slide

rails on sides of drawer opening.
Lift front of drawer slightly and push firmly
to close drawer.

Numbers
correspond
to steps.

7.

1.

12.

14.

13.

1.

9. 11.

4.

10. 5.

6.

8.

10. 5.

2.

10.

13. 14.