Kirkland Pth106a-ss Owner's Manual

GAS-FIRED INFRARED

OUTDOOR PATIO HEATER

INSTALLATION, OPERATION

MAINTENANCE INSTRUCTIONS

FOR MODEL PTH106A-SS

TABLE OF CONTENTS PAGE

IMPORTANT …………………………………………………………………… 1
TOOLS & PARTS ……………………………………………………………….. 2
PRECAUTIONS………………………………………………………………….. 3
ASSEMBLY INSTRUCTIONS …………………………………………………. 4
GAS REQUIREMENTS & LEAK TESTING ………………………………….. 7
SAFETY CHECKS ………………………………………………………………. 8
LOCATING HEATER FOR USE ………………………………………………. 9
LIGHTING / SHUTDOWN ………………………………………………………. 10
STORAGE / BURNER REMOVAL………………………………..……………. 12
BURNER INSTALLATION / PILOT CLEANING ……………………………… 13
BURNER REMOVAL ……………………………………………………………. 14
TROUBLE SHOOTING .………………………………………………………… 15
PARTS LIST ……………………………………………………………………… 16
WARRANTY ……………………………………………………………………… 17

READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR PATIO HEATER IS
PROPERLY INSTALLED, ASSEMBLIED AND CARED FOR. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF
YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR
DEALER, GAS APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY.

NOTE TO INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.

NOTE TO THE CONSUMER:
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

STOP

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE
DO NOT RETURN TO PLACE OF PURCHASE

IMPORTANT NOTICE:
DO NOT return to place of purchase!!!
Please contact Customer Service hotline at 800-913-8999 for help.

IMPORTANT

* * *

For outdoor use only (outside any enclosure)

WARNING

Improper operation, installation, adjustment, alteration,
servicing or maintenance can cause severe property
damage or serious injury or death. Please read the
installation, operation & maintenance instructions
thoroughly before installing or servicing this equipment.

* * *

* * *

FOR YOUR SAFETY

* * *

If you smell gas:

z Shut off gas to appliance.
z Extinguish any open flame.
z If odor continues, immediately call your gas

supplier.

For your safety:

Do not store or use gasoline or other flammable vapor
and liquids in the vicinity of this or any other appliance.

Page 1

TOOLS AND PARTS NEEDED FOR ASSEMBLY

NOTE: 20 pound (7.87kgs), 5 Gallon ( 18.9 litr es ) LPG Tank is not supplied

Tools Needed:
Phillips Head Screwdriver

Adjustable Opening Wrench
Spray Bottle of Soapy Water (To check for leaks)

Parts Supplied:

Reflector (3)
Dome Cap (1)
Reflector Plate (1)
Square T able (1)
Table Leg (4)
Heater Head With PVC Hose Assembly (1)
Post Assembly (1)
Gas Tank Enclosure Assembly (1)
LPG Gas regulator with Hose (1)

Hardware Bag

Post Socket 1/4” Acorn-cap (4)
Post Socket 1/4” Flat Washer (4)

Table Leg 5/32” Truss Head Screw (4)
Table Flat 5/32” Truss Head Screw (8)

Reflector 5/32” Truss Head Screw (3)
Reflector Plate 1/4” Tr uss Head Screw (3)
Heater Head 3/16” Truss Head Screw (4)
1/4” X 2-1/4” Long Thread Ends Stud (1)

Reflector Nut (1)

Tank Hook (1)

For Service Questions Replacement parts or other assistance, Please call Nexgrill Customer Service Hotline at:

Nexgrill Industries, Inc
145 Brea Canyon Road

Walnut, CA 91789

[phone]

Page2

IMPORTANT NOTICE:
DO NOT return to place of purchase!!!
Please contact Customer Service hotline at 800-913-8999 for help.

z Do not use this space heater in an

explosive atmosphere. Keep heater away
from areas where gasoline or other
flammable liquids or vapors are stored.

z Prior to use, check for damaged parts

such as hoses regulators, pilot or burner.

z Do not attempt to alter unit in any manner .

EXAMPLE: using the heater without the
top canopy reflector or radiant screen. Do
not shorten the burner post assembly.

z Heater must always be placed on a solid

and level surface.

z Always maintain proper clearance to

combustible materials. Top 36" (91cm)
Side 36" (91cm).

z Always assure there is ample fresh air

ventilation for outdoors use ONLY.

z Never replace or substitute the regulator

with any regulator other than the factory
suggested replacement.

z Do not clean heater with cleaners that are

combustible or corrosive.

z Do not paint radiant screen, control panel

or top canopy reflector.

z All leak tests should be done with a soapy

solution.
FLAME TO CHECK FOR LEAKS.

z The LP tank should be turned off when

the heater is not in use.

z At least once a year, the unit should be

inspected for the presence of spiders,
spider webs or other insects. The burner
area is a common spider haven and can
damage the heater and render it unsafe
for use, Check the heater immediately if
any of the following exists:

1. The smell of gas in conjunction with

extreme yellow tipping of the burner
flames.

2. The heater does not reach temperature.

NOTE: PLEASE READ THE FOLLOWING SAFETY

NEVER USE AN OPEN

PRECAUTIONS

3. The burner makes a popping noise during
use (a slight popping noise is normal when
the burner is extinguished).

z The LP regulator/hose assembly should

be located out of pathways where people
may trip over it or in area where the hose
will not be subject to accidental damage.

z Children and adults should be aware of

hazards of high surface temperature and
should stay away to avoid burns of
clothing ignition.

z Young children should be carefully

supervised when they are in the area of
the heater.

z Clothing or other flammable material

should not be hung from the heater, or
placed on or near the heater.

z Any guard or other protective device

removed for servicing the heater must be
replaced prior to operating the heater.

z Installation and repair should be done by

a qualified service person. The heater
must be inspected before use and at least
annually by a qualified service person.
More frequent cleaning may be required
as necessary. It is imperative that the
control compartment, burner and
circulating air passageways of the heater
be kept clean.

z Keep the appliance area clear and away

from combustible material, gasoline and
other flammable vapors and liquids.

z Do not obstruct the flow of combustion

and ventilation air.

z Keep the ventilation opening of the

cylinder enclosure free and clear of
debris.

Page 3

IMPORTANT NOTICE:
DO NOT return to place of purchase!!!
Please contact Customer Service hotline at 800-913-8999 for help.

ASSEMBLY INSTRUCTIONS

STEP 1. Attach Table Legs

z Attach the post socket to the top of the tank

enclosure using four 1/4”(M6) flat washers and
four 1/4” (M6) acorn-caps.

z Secure the four table legs with four of 5/32”

(M4) truss head screws.

STEP 2. Secure The T able

z Put the square table onto the legs and secure

with eight of 5/32” (M4) truss head screws.

Page4

IMPORTANT NOTICE:
DO NOT return to place of purchase!!!
Please contact Customer Service hotline at 800-913-8999 for help.

STEP 2. Attach Reflector

z Combine the three pieces of the reflector together
z Tighten up with three 5/32” (M4) screws.
z Put the reflector plate on reflector then tighten up

with three 1/4”(M6) truss head screws from the
bottom up.

ASSEMBLY INSTRUCTIONS

STEP 2

STEP 3: Attach The Reflector nut & Post

.
z Screw the 1/4”x 2-3/4 ” (M6x60mm) dual threaded

end-stud into the emitter top.

z Attach the reflector, dome cap and nut onto the

emitter top. It screws onto one end of the dual
threaded end stud screwed into the emitter top.

z Insert the gas hose from the heater down through

the pedestal post.

z Attach th e pedestal post onto the heater head with

four 3/16” (M5) truss head screws.

STEP 3

Page5