12” INDUSTRIAL JOINTER/PLANER WITH
SPIRAL CUTTERHEAD
INSTRUCTION MANUAL
COPYRIGHT © 2017 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: KC-12HJPC
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 12” INDUSTRIAL JOINTER/PLANER
OFFERS A 2-YEAR LIMITED WARRANTY
INTENDED FOR NON COMMERCIAL USE
KING CANADA TOOLS
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence
or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be
liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an
authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our
authorized service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if
any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the
warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
GENERAL & SPECIFIC
SAFETY RULES
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific
potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a
3-prong grounding type plug to fit the proper grounding type
receptacle. The green conductor in the cord is the grounding wire.
NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the swich is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of improper
accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store materials
such that it is necessary to stand on the tool to reach them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check for
alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
parts that are damaged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to
a complete stop.
SPECIFIC SAFETY RULES FOR MACHINESWITHA SPIRAL
CUTTERHEAD
Safety is a combination of common sense, staying alert and knowing
how your machine works. Read and understand the following safety
rules before operating.
1. For your own safety, read the entire instruction manual before
operating the planer.
2. Be sure that the cutterhead inserts are securely installed in the
cutterhead.
3. Always use clean, properly sharpened inserts. Dirty or dull inserts
are unsafe and can lead to accidents.
4. Do not force stock into the cutterhead. The machine will perform
better and more safely when working at the rate for which it was
designed.
5. Be sure that the cutterhead has gained full operating speed
before starting to joint/plane a workpiece.
6. Inspect stock and remove all foreign objects before jointing/
planing. Make sure that all stock is clean and free of any dirt,
nails, staples, tiny rocks or any other foreign objects that may
damage the inserts. Only process natural solid wood boards.
Never joint/plane MDF, particle board, plywood, laminates or other
synthetic materials.
7. Do not operate this machine when tired, distracted, or under the
effects of drugs, alcohol or any medication that impairs reflexes or
alertness.
8. Keep guards in place and in working order. If a guard must be
removed for maintenance or cleaning be sure it is properly
re-attached before using the machine again.
9. Kickback is when the workpiece is ejected at high speeds by the
force of the cutterhead. To minimize the risk of injury from
kickback, use proper feeding technique and stand to one side, out
of the path of a potential kickback.
10. Place stock firmly against the table and use suitable in-feed and
out-feed support if stock is too long.
11. Always use push blocks for jointing material less than 3” in height.
12. Do not perform planing operations on material shorter than 6”,
narrower than 3/4” or less than 1/2” thick.
13. Never make jointing or planing cuts, deeper than 1/8”. On cuts
more than 1-1/2” wide, adjust depth of cut to 1/16” or less to avoid
overloading machine and to minimize chance of kick-back (work
thrown back toward you).
GETTING TO KNOW
YOUR 12” JOINTER/PLANER
Getting to know your 12” Jointer/Planer
1) Cutterhead guard height adjustment knob
2) Adjustable fence
3) Cutterhead guard
4) Cutterhead guard lock knob
5) Table raising handle
6) Jointer infeed table
7) Infeed table adjustment lever
8) Infeed table adjustment lock knob
9) Planer outfeed roller support
10) Jointer table lock levers (1 of 2)
12) Outfeed table adjustment lock knob
13) 4” dust chute (Jointer mode)
14) Outfeed table adjustment lever
15) 4” dust chute (Planer mode)
16) 4” dust chute release pin
17) Planing thickness scale & indicator
18) Planer table raising/lowering handwheel
19) Planer table lock handle
20) Planer power feed lever
21) Planer table (infeed side)
11) Magnetic switch (On/Off)
Specifications
MODEL KC-12HJPC
Maximum jointing/planing width
Maximum depth of cut
Spiral cutterhead speed
Spiral cutterhead diameter
Number of cutter inserts
Maximum planing thickness
Planing feed rate
Table sizes (jointer/planer) 51” x 12-1/4” / 21-3/4” x 12-1/4”
Motor 10 Amp.
Voltage
Assembled dimensions (LxWxH)/weight 51” x 32” x 39-1/2” / 465 lbs
Package dimensions (LxWxH)/weight 52” x 22-1/2” x 38-1/2” / 540 lbs
12”
1/8”
6,500 RPM
2-3/4”
60 (15mm x 15mm x 2.5mm)
8-3/4”
22 FPM
220V, 1 phase, 60 Hz
Loading...