Page 1
10” TABLE SAW
INSTRUCTION MANUAL
COPYRIGHT © 2002 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: KC-10FX
Page 2
IMPORTANT INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 10” TABLE SAW
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this tool are available at our authorized KING CANADA service centers across Canada. For servicing, contact or
return to the retailer where you purchased your product along with your proof of purchase.
LIMITED TOOL WARRANTY
KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants
to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free
from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs
or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or for
incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product or
part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA
will either repair or replace the product.
PARTS DIAGRAM & P
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
ARTS LISTS
OFFERS A 2-YEAR LIMITED WARRANTY
KING CANADA TOOLS
OR INDUSTRIAL USE.
F
KING CANADA TOOLS INC. DORVAL, QUEBEC, CANADA H9P 2Y4
Page 3
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
. KNOW YOUR TOOL
1
Read and understand the owners manual and labels affixed to
the tool. Learn its application and limitations as well as its
pecific potential hazards.
s
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a
-prong grounding type plug to fit the proper grounding type
3
receptacle. The green conductor in the cord is the grounding
wire. NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wr
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
ed areas and benches invite accidents. Make sure the floor
Clutter
is clean and not slippery due to wax and sawdust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them
to rain. Keep work area well lit and provide adequate
surrounding work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the
proper speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
enches
ootwear is recommended. Wear protective hair covering to
f
contain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
lways wear safety glasses (ANSI Z87.1). Everyday eyeglasses
A
only have impact resistant lenses, thet are
Also use a face or dust mask if cutting operation is dusty.
3. DON’T OVERREACH.
1
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
e servicing, when changing accessories or attachments.
Befor
16. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of improper
accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store
materials such that it is necessary to stand on the tool to reach
them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check for
alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
parts that are da -maged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to
a complete stop.
NOT safety glasses.
SPECIFIC SAFETY INSTRUCTIONS FOR TABLE SAWS
AYS USE A GUARD.
1. ALW
Always use a guard, splitter and anti-kickback fingers on all
“thru-sawing” operations. Thru-sawing operations are those
when the blade cuts completely through the workpiece as in
ripping or cross cutting.
2. ALWAYS HOLD THE WORK.
Always hold the work firmly against the miter gauge or fence.
3. ALWAYS USE A PUSH STICK.
For ripping narrow stock. Refer to ripping applications in
instruction manual where push sticks are covered in detail.
4. NEVER.
Never perform any operations “free-hand” which means using
your hands to support or guide the workpiece. Always use either
the fence or the miter gauge to position and guide the workpiece.
5. NEVER.
Never stand or have any part of your body in line with the path
of the saw blade.
6. NEVER REACH BEHIND.
Never reach behind or over the cutting tool with either hand for
any reason.
7. MOVE THE RIP FENCE.
Move the rip fence out of the way when cross cutting.
8. WHEN CUTTING MOULDINGS.
Never run the stock between the fence and the moulding
cutterhead. Refer to moulding applications in the manual for details.
9. DIRECTION OF FEED.
Feed work into the blade or cutter against the direction or
rotation of the blade or cutter.
10. NEVER.
Never use the fence as a cut-off gauge when you are crosscutting.
11. NEVER.
Never attempt to free a stalled saw blade without first turning the
saw OFF.
12. PROVIDE ADEQUATE SUPPORT.
o the rear and sides of the table saw for wide or long workpieces.
T
13. AVOID KICKBACKS.
Avoid kickbacks (work thrown back towards you) by keeping the
blade sharp, by keeping the rip fence parallel to the saw blade, by
keeping the splitter and anti-kickback fingers and guard in place
and operating, by nor releasing work before it is pushed all the
way past the saw blade, and by not ripping work that is twisted
or warped or does not have a straight edge to guide along the
fence.
14. AVOID AWKWARD OPERATIONS.
Avoid awkward operations and hand positions where a sudden
slip could cause your hand to move into the cutting tool.
Page 4
GETTING TO KNOW YOUR 10” TABLE SAW
MODEL: KC-10FX
1. Magnetic switch
2. Blade raising handwheel
3. Miter gauge
4. Blade guard & splitter
5.Blade tilting handwheel
6. Dust chute
SPECIFICATIONS
0
90
to 45
4000 R.P
3HP
.M.
5/8”
Horsepower
Amps/Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.7A @ 220V
Table size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-1/2” x 27”
able size with extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1/2” x 27”
T
Miter angle
Bevel angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10”
Maximum cutting depth 90 bevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3”
Maximum cutting depth 45 bevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3/4”
Arbor speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Arbor diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
Left & Right
0
Page 5
ELECTRICAL REQUIREMENTS
MODEL: KC-10FX
ARNING!
W
LL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN
A
SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE TABLE SAW DISCONNECTED FROM THE
OWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!
P
POWER SUPPLY
WARNING:
20-AMP, BRANCH CIRCUIT AND USE A 20-AMP TIME DELAY
FUSE OR CIRCUIT BREAKER. FAILURE TO CONNECT IN THIS
WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.
Your table saw must be properly grounded. Not all outlets are
properly grounded. If you are not sure if your outlet is properly
grounded, have it checked by a qualified electrician.
WARNING: IF NOT PROPERLY GROUNDED, THIS JOINTER
CAN CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS. TO AVOID SHOCK OR FIRE, IF
THE POWER CORD IS WORN OR DAMAGED IN ANY WAY,
HAVE IT REPLACED IMMEDIATELY.
GROUNDING
This table saw must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for electric
current, to reduce the risk of electric shock. This table saw is
equipped with a cord which will require a 220V equipmentgrounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING: TO MAINTAIN PROPER GROUNDING OF YOUR
TABLE SAW, DO NOT REMOVE OR ALTER THE GROUNDING
PRONG IN ANY MANNER.
YOURTABLE SAW MUST BE CONNECTED TO A
PROPERLY GROUNDED OUTLET
CURRENT
CARRYING PRONGS
GROUNDING PRONG
FIGURE 1
There is no plug supplied with the motor, therefore to operate at 220V,
a plug with two flat, current-carrying prongs in tandem, and one
round or “U” shaped longer ground prong, as shown in Fig. 1, must
be installed. This plug is used only with pr
grounded receptacle, as shown in Fig. 1.
oper mating 3-conductor
Page 6
ASSEMBLY
ASSEMBLING EXTENSION WINGS
Assemble the Table Extension Wings to your saw as follows:
Fasten extension wings to the table using six hex. head screws and lockwashers
supplied. Use a straight edge to level the extension wings to the table surface as
hown in fig. 2. Also make sure the extension wings are flush with the front
s
edge of the table.
ASSEMBLING BLADE GUARD AND SPLITTER
WARNING!
PROPER OPERATING POSITION. FALIURE TO DO THIS MAY CAUSE
SERIOUS INJURY!
1. Insert threaded end of rod (D-Fig. 4) through hole in casting and carriage at
rear of machine. Tighten securely with a wrench.
2. Thread nut (N) on shaft inside saw cabinet. DO NOT tighten yet. (Fig 3).
3. Assemble lower rear bracket (Fig. 4) to rod.
4. Using wrench, loosely secure two screws located under bracket.
5. Using screw and lockwasher provided, loosely attach splitter bracket to
lower rear bracket.
6. Align front of splitter with saw flange using straight edge and tighten nut.
(N-Fig. 3).
7. Tilt blade guard up.
8. If the blade is not installed, using washer and nut provided, assemble saw
blade to arbor. NOTE: SAW ARBOR HAS LEFT-HAND THREADS.
9. Using straight edge and square (Fig. 4) align splitter with blade and table.
10. When splitter aligns with blade and is square with table, tighten screws on
bracket.
WARNING!
SOME CUTTING OPERATIONS (DADO BLADE, MOLDING CUTTERHEAD)
WON’T ALLOW USE OF BLADE GUARD AND SPLITTER ASSEMBLY. USE
EXTREME CAUTION DURING THESE OPERATIONS AS THE BLADE OR
CUTTERHEAD WILL BE EXPOSED AND COULD CAUSE SERIOUS INJURY.
ASSEMBLING OPTIONAL RIP FENCE SYSTEM
NEVER OPERATE SAW WITHOUT BLADE GAURD IN THE
FIGURE 2
FIGURE 3
King Canada has developed an optional Industrial Rip Fence System (KRF-100)
for your table saw. To assemble this Rip Fence System or another, please follow
the assembly instructions found in the Rip Fence instruction manual. As
reference only, Fig.5 illustrates the King Canada Industrial Rip fence System
assembly along with the installation of an optional 24” Router Extension table
(Model: EXT-24).
FIGURE 4
FIGURE 5
Page 7
ADJUSTMENTS
ADJUSTING 45 AND 90 DEGREE POSITIVE STOPS
Your saw is equipped with a positive stop at 45 and 90 degrees. To check
and adjust the positive stops, proceed as follows:
. Raise the saw blade to it’s maximum.
1
2. Set the blade at 90 degrees to the table by turning the blade tilting
andwheel counter-clockwise as far as it will go.
h
3. Place a square on the table as shown in Fig.7 and check to see if the
blade is at a perfect 90 degree angle to the table.
4. If the blade is not at 45 degrees loosen lock nut (A) Fig. 7 and turn
adjusting stop screw (B) in or out. The adjusting stop screw (B) should
stop against end of the tilting screw (C) when the blade is at 45 degrees
to the table. Recheck and adjust further if necessary.
5. If the 90 degree postive stop is not set properly, follow the same
procedure using screw (D) and nut (E).
ADJUSTING TABLE INSERT
The table insert (A) is placed in the opening in the saw table, as shown
in Fig. 8 and should be level with the surface of the saw table. To adjust
the table insert (A), use a straight edge as shown in Fig. 8 and turn the
four adjusting set screws (B) in the insert, in or out until the insert is flush
with the table top.
ADJUSTING MITER GAUGE
The miter gauge comes with adjustable index stops at 45 and 90 degrees
right and left.
To adjust index stops, tighten or loosen one of three adjusting screws (A)
Fig. 9 against stoplink (D).
o operate miter gauge:
T
1. Loosen lock knob (B) Fig. 9 and move body of miter gauge (C) to
ed angle. It stops at 90 degrees and 45 degrees both right and left.
desir
2. To rotate miter gauge body past these points, flip stoplink (D) out of
the way.
FIGURE 7
FIGURE 8
FIGURE 9
Page 8
OPERATION
CHANGING BLADES
1. Turn off saw and disconnect the electrical plug.
2. Raise the saw blade fully, hold the guard up and lock the saw at 0
egrees. Remove the table insert.
d
3. Jam a large piece of scrap wood into the blade teeth at the front. Fig.
10.
4. Place the blade wrench over the arbor nut and pull the wrench toward
you. Remove the arbor nut, flange and saw blade.
5. Place the new blade on the arbor shaft making certain the teeth point
down at the front of the saw. Replace the flange and the arbor nut.
6. Place the scrap wood in the blade’s teeth in the rear. Hold carefully so
if it silps or the blade turns, your hand will not contact the blade.
7. Using the wrench provided, securely tighten the arbor nut. Remove
the wrench and replace the table insert.
FIGURE 10
BLADE RAISING AND TILTING MECHANISIM
To raise or lower the blade, loosen lock knob (A) Fig. 11. and turn
raising handwheel (B) with the exception of hollow ground blades. The
blade should be raised 1/8” to 1/4” above the top surface of the
material being cut. With hollow ground blades the blade should be
raised to the maximum to provide chip clearance. To tilt the saw blade,
loosen lock knob (C) Fig. 11. and turn tilting handwheel (D). When
desired angle is obtained, tighten lock knob (C).
SAFETY PRECAUTIONS BEFORE OPERATION
The operation of power tools involves a certain amount of hazar
operator. Before attempting regular work we recommend you get the feel
of operations using scrap lumber to check setting. Read entire
uctions before you start to cut workpiece.
instr
safety pr
OPERA
Plain sawing includes ripping and crosscutting, plus a few other
standard operations of a fundamental nature. The following methods
feature safety. As with all power tools there is a certain amount of hazard
involved with the operation and his use of the tool. Using the tool with
the respect and caution demanded as far as safety pr
concerned will considerably lessen the possibility of personal injury
However, if normal safety precautions are overlooked or completely
ignored, personal injury to the operator can develop. It is good practice
to make trial cuts using scrap material when setting up you saw for
operation.
ecautions to avoid personal injury
TION
Always pay attention to
.
d for the
ecautions ar
e
A
B
D
C
FIGURE 11
.
Page 9
OPERATION
ROSSCUTTING
C
Crosscutting requires the use of the miter gauge to position and guide
the work. Place the work against the miter gauge and advance both the
miter gauge and work toward the saw blade, as shown in Fig. 12. The
miter gauge may be used in either table slot, however, most operators
refer the left groove for average work. When bevel cutting (blade
p
ilted), use the table groove that does not cause interference of your hand
t
or miter gauge with the saw blade guard.
Start the cut slowly and hold the work firmly against the miter gauge
and the table. One of the rules in running a saw is that you never hang
onto or touch a free piece of work. Hold the supported piece, not the free
piece that is cut off. The feed in crosscutting continues until the work is
cut in two, then the miter gauge and work ar
point. Before pulling the work back it is good practice to give the work a
little sideways shift to move the work slightly away from the saw blade.
Never pick up any short length of free work from the table while the saw
is running. A smart operator never touches a cut-off piece unless it is at
least a foot long. Never use the fence as a cut-off gauge when cross
cutting.
For added safety and convenience the miter gauge can be fitted with an
auxiliary wood-facing that should be at least 1 inch higher than the
maximum depth of cut, and should extend 12 inches or more on either
side of the blade. This auxiliary wood facing can be fastened to the front
of the miter gauge by using two wood screws through the holes
provided in the miter gauge body and into the wood-facing.
e pulled back to the starting
FIGURE 12
RIPPING
Ripping is the operation of making a lengthwise cut through a board, as
shown in Fig. 13, and the rip fence is used to position and guide the
work. One edge of the work rides against the rip fence while the flat side
of the board rest on the table. Since the work is pushed along the fence,
it must have a straight edge and make solid contact with the table. The
saw guard must be used. The guard has anti-kickback fingers and a
splitter to prevent the saw kerf fr
Start the motor and advance the work holding it down and against the
fence. Never, stand in the line of the saw cut when ripping. Hold the
work with both hands and push it along the fence and into the saw blade
as shown in Fig. 13. The work can then be fed through the saw blade
with one or two hands.
When this is done the work will either stay on the table, tilt up slightly
and be caught by the rear end of the guard or slide off the table to the
Alternately
floor.
which the work is lifted and brought back along the outside edge of the
fence. The waste stock remains on the table and is not touched with the
hands until the saw is stopped unless it is a large piece allowing safe
removal.
, the feed can continue to the end of the table, after
om closing.
FIGURE 13
Page 10
OPERATION
USING ACCESSORY MOULDING CUTTERHEAD*
Moulding is cutting a shape on the edge of face of the work. Cutting
moulding with a moulding cutterhead in the circular saw is a fast, safe
and clean operation. The many different knife shapes available make it
possible for the operator to produce almost any kind of moulding, such
as various styles of corner moulds, picture frames, table edges, etc.
The moulding head consists of a cutterhead in which can be mounted
various shapes of steel knives,as shown in fig. 14. Each of the three
knives in a set is fitted into a groove in the cutterhead and securely
clamped with a screw. The knife grooves should be kept free of sawdust
which would prevent the cutter from seating properly.
The moulding cutterhead (A) fig.15, is assembled to the saw arbor in the
same manner as the saw blade. The guard, splitter and anti-kickback
finger assembly can not be used when moulding and must be removed
from the saw as shown. Also, the supplied accessory moulding
cutterhead table insert (B) Fig. 15, must be used in place of the standard
table insert.
IMPORTANT: NEVER RUN THE STOCK BETWEEN THE FENCE AND
THE MOULDING CUTTERHEAD AS IRREGULAR SHAPED WOOD
WILL CAUSE KICKBACK.
When moulding end grain, the miter gauge is used. The feed should be
stowed up at the end of the cut to prevent splintering.
In all cuts, attention should be given to the grain, making the cut in the
same direction as the grain whenever possible.
ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS
COMPLETE.
FIGURE 14
USING ACCESSORY DADO HEAD*
Dadoing is cutting a rabbet or a wide groove into the work. Most dado
head sets are made up of two outside saws and four or five inside cutters,
as shown in Fig. 16. V
cut grooves from 1/8” to 13/16” for use in shelving, making joints,
tenoning, grooving, ect. The cutters are heavily swaged and must be
arranged so that this heavy portion falls in the gullet of the outside saws,
as shown in Fig. 17. The saw and cutter overlap is shown in Fig. 17 (A)
being the outside saw, (B) and inside cutter, and (C) a paper washer
which can be used as needed to contr
groove is cut by using the two outside saws. The teeth of the saws should
be positioned so that the raker on one saw is beside the cutting teeth on
the other saw.
The dado head set is assembled to the saw arbor in the same manner as
the saw blade. The guar
not be used when dadoing and must be r
supplied accessory dado head table insert must be used in place of the
standard table insert.
NEVER USE THE DADO HEAD IN A BEVEL POSITION!
ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS
COMPLETE!
arious combination of saws and cutters are used to
1/4”
ol the exact width of groove.
d splitter and anti-kickback finger assembly can
emoved from the saw. Also the
A
FIGURE 15
FIGURE 16
A
B
C
* Moulding cutterhead and Dado head accessories are not available from King Canada,
please contact your local dealer for information on acquiring these standard accessories.
FIGURE 17
Page 11
TROUBLESHOOTING
ROBLEM
P
AW WILL NOT START
S
1. Saw not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord damaged.
. Overload relay not set.
4
OVERLOAD KICKS OUT FREQUENTLY
1. Extension cord too light or too long.
2. Feeding stock too fast.
3. Blade in poor condition (dull, warped,
gummed).
4. Blade binding due to misaligned rip fence.
5. Blade binding due to warped wood.
6. Low house current.
DOES NOT MAKE ACCURATE 450AND 90
RIP CUTS
1. Positive stop not adjusted properly.
2. Tilt angle pointer not set properly.
MATERIAL PINCHES BLADE WHEN
RIPPING
1. Rip fence not aligned with blade.
2. Warped wood.
OLUTION
S
1. Plug in saw.
2. Replace fuse or reset circuit breaker.
3. Have cord replaced by a certified electrician.
. Push overload reset button.
4
1. Replace with adequate size cord.
2. Feed stock more slowly.
3. Clean or replace blade.
4. Check and adjust the rip fence.
5. Select another piece of wood.
6. Contact your electrical company.
0
1. Check blade with square and adjust positive stop.
2. Check blade with square and adjust pointer to zero.
1. Check and adjust rip fence.
2. Select another piece of wood.
MATERIAL BINDS ON SPLITTER
1. Splitter not aligned correctly with blade.
SAW MAKES UNSATISFACTORY CUTS
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
4. Incorrect blade for work being done.
5. Gum or pitch on table causing erratic feed.
BLADE DOES NOT COME UP TO SPEED
1. Extension cord too light or too long.
2. Low house curr
3. Motor not wired for correct voltage.
MACHINE VIBRA
1. Saw not mounted securely to stand.
2. Stand is on uneven floor.
3. Damaged saw blade.
4. Bad V
5. V
6. Bent pulley.
7. Improper motor mounting.
8. Excessive play in raising mechanism.
9. Loose hardware.
BLADE DOES NOT RAISE OR TILT FREELY
1. Too much tension in the raising mechanism.
2. Sawdust or dirt in raising or tilting
-belt.
-belt not tensioned pr
mechanisms.
ent.
TES EXCESSIVELY
.
operly
1. Check and align splitter with blade.
1. Replace blade.
2.Turn blade around.
3. Remove blade and clean with turpentine and steel wool.
4. Change the blade.
5. Clean the table with turpentine and steel wool.
1. Replace with adequate size cord.
2. Contact your electric company
3. Refer to motor nameplate for correct wiring.
1. Tighten all mounting hardware.
2. Reposition on flat level surface. Fasten to floor if necessary.
3. Replace blade.
4. Replace belt.
Adjust belt tension by moving motor and/or motor bracket.
5.
6. Replace pulley.
7. Check and adjust motor mounting.
8. Adjust worm and arbor bracket.
9. Tighten all nuts, bolts and set screws.
1. Adjust raising worm and arbor bracket.
ush or blow out loose dust or dirt.
2. Br
.
Loading...