King Canada K-1501 Instruction Manual

TENONING JIG

INSTRUCTION MANUAL

COPYRIGHT © 2006 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

MODEL: K-1501

IMPORTANT INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS TENONING JIG

OFFERS A 2-YEAR LIMITED WARRANTY

KING CANADA TOOLS

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this tool are available at our authorized KING CANADA service centers across Canada. For servicing, contact
or return to the retailer where you purchased your product along with your proof of purchase.

LIMITED TOOL

KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to
the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free
from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents,
repairs or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or
for incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product
or part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA
will either repair or replace the product.

WARRANTY

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

KING CANADA TOOLS INC. DORVAL, QUEBEC, CANADA H9P 2Y4

GENERAL SAFETY INSTRUCTIONS

. KNOW YOUR TOOL

1

Read and understand the owners manual and labels affixed to

the tool. Learn its application and limitations as well as its

pecific potential hazards.

s

2. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before using or turning it on.

3. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

4. MAKE WORKSHOP CHILD-PROOF.

Use padlocks, master switches or remove starter keys.

5. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings,

watch) because they could get caught in moving parts. Non-

slip footwear is recommended. Wear protective hair covering

to contain long hair. Roll up long sleeves above the elbows.

6. ALWAYS WEAR SAFETY GLASSES.

Always wear safety glasses (ANSI Z87.1). Everyday

UNPACKING

eyeglasses only have impact resistant lenses, they are

safety glasses. Also use a face or dust mask if cutting

operation is dusty.

7. DON’T OVERREACH.

Keep proper footing and balance at all times.

8. MAINTAIN TOOL WITH CARE.

Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

9. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

10. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are

damaged should be carefully checked to ensure that they will

operate properly and perform their intended function. Check for

alignment of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation. A guard or

other parts that are damaged should be properly repaired or

replaced.

NOT

Unpack the contents of the Tenoning Jig box and all the
loose parts. The illustration to the right shows all the items
supplied with the Tenoning Jig. Compare them to the list

.

below

1- Jig assembly, 3/8” x 3/4” T-slot bar and

vertical work support assembly
2- Clamp assembly
3- Special Bolt
4- Clamp arm
5- Lockwashers (2)
6- Cap screws (2)
7- 1/4” x 3/4” T-slot bar
8- Washers (2)
9- Round hd allen screws (2)
10- Rubber handles (2)
11- 8mm Hex. key
12- 4mm Hex. key
13- 3mm Hex. key
14- 2.5mm Hex. key

Not shown- Instruction manual

FIGURE 1