Kidde KN-COP-DP User Manual
AC Powered, Plug-In
Carbon Monoxide Alarm
• Part Number 900-0056 • KN-COP-DP
Description
The Kidde 900-0056 is an AC powered, plug-in carbon
monoxide alarm that can be installed easily in any standard wall outlet. The 900-0056 uses advanced technology to monitor for carbon monoxide levels in your home
and features a Nighthawk
TM
, electrochemical sensor,
the world’s most accurate carbon monoxide sensing
technology*. The digital display feature allows for easy
viewing of carbon monoxide levels.
Consumer Benefits
The Kidde 900-0056 AC powered, plug-in carbon
monoxide alarm provides you and your family a warning
signal against the dangers of carbon monoxide levels in
your home. This alarm is easily installed in any of your
AC wall outlets. The digital display feature allows for
easy viewing of carbon monoxide levels from 30-999PPM
(parts per million). The 900-0056 is UL listed and offers a
5-year limited warranty.
Features and Benefits
• Digital Display – Displays the level of carbon monoxide
the unit is sensing. The unit updates this reading every
15 seconds.
• Peak Level Button – Displays the peak CO level
recorded by the alarm since it was last reset or unplugged.
•Test Button – Tests unit’s electronic circuitry and horn
and resets the unit during alarm.
*Based on accuracy claims of major manufacturers
NIGHTHAWK
TECHNOLOGY
World’s Most Accurate
Carbon Monoxide Alarm
*
TM
Digital Display
Displays the level of carbon monoxide the unit is sensing.
The unit updates this reading every 15 seconds.
Test/Reset Button
Tests units electronic circuitry and horn and resets
the unit during alarm.
Peak Level Button
Displays the peak CO level recorded by the alarm since
it was last reset or unplugged.
NEW
FEATURE:
Alerts user to replace CO alarm
after 7 years of operation
1394 South Third Street, Mebane NC 27302
1-800-880-6788 • www.kiddeus.com
AC Powered, Plug-In
Carbon Monoxide Alarm
Part Number 900-0056
Unit Number KN-COP-DP
Architectural and Engineering
Specifications
The carbon monoxide alarm shall be Kidde Unit Number KN-COPDP (part number 900-0056) or approved equal. It shall be powered
by a 120VAC, 60 Hz source. The temperature operating range shall
be between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operation range shall be 5% - 95% relative humidity.
The CO sensor shall be of a fuel cell design and shall meet the
sensitivity requirements of Underwriters Laboratories UL 2034 Single
Station Carbon Monoxide Detectors. The unit shall provide accuracy of +/-20% + 15 parts per million (ppm) when reading CO concentration levels.
The alarm shall include an attached plug that can be installed
in any outlet following the UL/NFPA/Manufacturer’s recommended
guidelines. The plug shall be capable of being rotated so the alarm
remains vertical independent of whether the electrical socket is
mounted vertically or horizontally.
The unit shall incorporate a digital display that meets the sensitivity requirements of UL 2034. The display will identify the levels of
CO in parts per million (ppm) once that level reaches 30ppm (i.e.:
“abnormal” levels). The display will have a red dot in the lower
right corner that will blink to indicate the normal operation.
The alarm shall include a test button that will electronically
simulate the presence of CO and cause the unit to go into alarm.
This sequence tests the unit’s electronics to ensure proper operation.
The CO sensor will not alarm to levels of CO below 30 ppm
and will alarm in the following time range when exposed to the
corresponding level of CO.
The alarm shall include a piezoelectric horn that is rated at 85
decibels at 10 feet. When the unit detects carbon monoxide, the
alarm pattern will be four (4) short beeps – followed by five (5)
seconds of silence – followed by four (4) short beeps. A number
reading will appear on the digital display identifying the CO
concentration (in ppm).
The unit shall include a peak level memory feature that will
store the peak CO level sensed since the unit was last reset. The
peak CO level stored in the unit’s memory shall be displayed (in
ppm) on the digital display by pressing the appropriate button
on the unit. The memory shall also be capable of being reset.
The unit shall be listed to UL 2034. It shall also include a 5-year
manufacturer’s limited warranty.
Technical Specifications
Part Number: 900-0056
Unit Number: KN-COP-DP
UPC Number: 7-84608-00560-1
Power Source: 120VAC
Sensor: Electrochemical
Audio Alarm: 85dB at 10ft
Temperature Range: 40˚F (4.4˚C) to 100˚F (37.8˚C)
Humidity Range: Up to 95% relative humidity (RH)
Size: 5.65”L x 3.25”W x 1.9”H
Weight: 1lb
Interconnects: No
Wiring: Plug-In
LED: Displays CO concentration in PPM
Warranty: 5 year limited
*Based on accuracy claims of major manufacturers
UNIT MASTER PACK CUT CASE POWER TOWER
1
PDQ
2
4
12
36
Ordering Information
Clam Shell UPC: 7-84908-00560-1
Part Dimensions Case/ Layers/ Skid
Number I 2 of 5 Pack Quantity (w x d x h inches) Weight Skid Skid Weight
900-0056** N/A Individual 7 x 2.5 x 10.75 1lb N/A N/A N/A
900-0056-02 107 84908 00560 8 PDQ (2 units) 7.75 x 6 x 11.75 2lbs 105 3 210lbs
900-0056-07 207 84908 00560 5 Master Pack (4 units) 7.75 x 11.5 x 12 4lbs 80 4 320lbs
900-0056-012 307 84908 00560 2 Cut Case (12 units) 15 x 18 x 12 12lbs 18 3 216lbs
900-0056-036 407 84908 00560 9 Power Tower (36 units) 20 x 24 x 50 (incl. pallet) 36lbs 3 3 108lbs
**Not for sale by individual unit
3.25"
1.9"
5.65"
Distributed by:
Loading...