Kidde i9010 Brochure

Sealed Battery
Smoke Alarm with Hush

TM

Part Number 900-0136 Model i9010 (formerly model 0910)

LED Indicator

A flashing red indicator light with four modes of
operation: Standby, alarm mode, hush mode and
memory set

Test/Reset Button

One button tests the unit’s circuit operation and resets
memory after an alarm condition occurs

TM

Hush

Feature

Temporarily silences nuisance alarms. Will not allow
hush to be activated unless unit is in alarm mode.

Battery Operated

No wiring needed

Sealed-In Lithium Battery

Unit will continue to operate for 10 years

Description

The Kidde i9010 is a 10-year, sealed battery, ionization, smoke alarm
with Alarm Memory and HushTM feature. The innovative design of
this alarm’s automatic activation is unlike any other smoke alarm.
The i9010 alarm will automatically activate when it is attached to the
mounting bracket; there are no pull-tabs, no switches, everything is
automatic. At the end of the alarm life, the unit will chirp, indicating
the alarm is in need of replacement. The customer can use a simple
tool such as a screwdriver to deactivate the unit, stopping the low
battery chirp and making it safe for disposal.

The sealed-in board-mounted battery will power the i9010 unit
for its complete 10-year life. No replacement battery will ever be
needed.

This alarm uses ionization sensing technology. Ionization sensing
alarms may detect invisible fire particles (associated with flaming
fires) sooner than photoelectric alarms. Photoelectric sensing alarms
may detect visible particles (associated with smoldering fires) sooner
than ionization alarms.

Kidde strongly recommends that both ionization and
photoelectric smoke alarms be installed to help insure
maximum detection of the various types of fire that can
occur within the home

The Kidde i9010 sealed battery operated smoke alarm
features a self-activation mechanism making installation simple
and easy. It also features HushTM feature allowing consumers to
temporarily silence nuisance alarms and an End of Life Alert
indicating it is time to replace the alarm.

At the end of the alarm’s 10-year life, deactivation of the alarm is
just as easy. Using a tool such as a small screwdriver, a deactivation
switch removes power from the alarm and renders the battery safe
for disposal. The alarm lockout feature mechanically prevents a deac­tivated unit from being mounted back on the mounting bracket.

Features and Benefits

• Sealed-InLithiumBattery – Sealed-in lithium power
supply; no battery replacement required over the 10
year life of the alarm. Eliminates worry about battery
removal or unauthorized deactivation of alarm.

• SelfActivation – Alarm automatically activates when
attached to the mounting bracket.

• AlarmMemory – Rapidly flashing LED alerts user if the
alarm has sounded since the last time the test/reset
button was used.

• Hush

alarms and will not allow hush mode to be activated
unless the unit is in alarm mode.

• Test/ResetButton – Tests unit’s circuit operation and
resets memory after an alarm condition occurs.

• EndofLifeWarning – Alarm chirps every 40-45
seconds indicating the alarm is in need of replacement.

• TamperResist – (when activated upon installation)
effective in preventing someone from removing the unit
from the mounting bracket.

• LED – A flashing red indicator light
with four modes of operation:
standby, alarm mode,
hush mode, and memory set.

TM

– Will temporarily silence nuisance

10

Sealed Battery Unit
Smoke Alarm with Hush

TM

Model i9010
Part Number 900-0136

Architectural and Engineering
Specifications

The smoke alarm shall be Kidde unit i9010/i9010CA or approved
equal. It shall be powered by a non-replaceable lithium battery with a
10-year life. The lithium battery shall be sealed in the unit to prevent
removal and/or tampering. The unit shall incorporate an ionization
sensor with nominal sensitivity of 0.88%/ft (.95%/ft for unit i9010CA).
The temperature operating range shall be between 40°F and 100°F
(4°C and 38°C) and the humidity operating range shall be 5% - 85%
relative humidity.

The smoke alarm can be installed on the surface of any wall or ceil­ing following the UL/Manufacturer’s approved placement guidelines.
The alarm shall incorporate an automatic activation feature that will
activate the unit as soon as it is attached to the mounting bracket, no
other steps are involved. The alarm shall provide optional tamper resis­tance that locks the unit to the mounting bracket and deters removal
of the unit from the wall or ceiling.

The alarm shall include a test button that will simulate a fire condition
and cause the unit to go into alarm. This sequence tests the unit’s
electronics to ensure proper operation.

The unit shall include a piezoelectric horn that is rated at 85 decibels
at 10 feet. The unit shall include the Hush
unit for 7-9 minutes if a nuisance condition occurs. The red LED will
illuminate for 1 seconds every 8 seconds and will automatically reset
itself. If the alarm is in the Hush mode and the condition that trig­gered the alarm persists, the alarm shall sound again to signal poten­tial danger despite its presence in Hush Mode.The unit shall incorpo­rate one red LED to indicate the alarm’s current status and mode of
operation. The LED will indicate one of four modes:

Standby Mode: LED will flash every 40-45 seconds to indicate
the unit is operating correctly

Alarm Mode: LED will flash every 1.5 seconds to indicate the
unit is alarming and will be accompanied by the
horn sounding (Model i9010CA LED will flash on
for 1 second and off for 1 second)

Hush Mode: LED will illuminate for 1 seconds every 8
seconds to indicate the unit is temporarily silenced

Memory Set Mode: If Alarm Memory has been set, the LED will
flash rapidly when the test button is pressed.

TM

feature that silences the

The unit shall include an End of Life Alert which is indicates the
alarm needs to be replaced. The unit will “chirp” once every 40-45
seconds to notify the user. The unit shall have a deactivation switch
to disable it and make it safe for disposal. The unit shall at a mini­mum meet the requirements of UL217, NFPA72, (chapter 11 2002
edition) The State of California Fire Marshall, NFPA101 (One and
two family dwellings) Federal Housing Authority (FHA), Housing
and Urban Development (HUD).

Technical Specifications

Model: i9010 (i9010CA Canadian model)

UPC Number: 0-47871-90136-4

Power Source: One, 3V Lithium battery

Sensor: Ionization

Audio Alarm: 85dB at 10ft

Temperature Range: 40˚F (4.4˚C) to 100˚F (37.8˚C)

Humidity Range: 5%-85% relative humidity (RH)

Size: 5.6” in diameter x 1.55” depth

Weight: 1 lb.

Interconnects: No

LED: Four modes of operation

Warranty: 10 year limited

5.6" 1.55"

Ordering Information

Clamshell UPC: 0 47871 90136 4

GiftBox: 0 47871 08697 9

Part Dimensions Case/ Skid

Number I2of5 PackQuantity (wxdxhinches) Weight Skid Weight

900-0136 N/A N/A Individual Clamshell 7.25 x 1.75 x 11 1 lbs N/A N/A

900-0136 N/A N/A Individual Box 5.75 x 2 x 6.25 1 lbs N/A N/A

900-0136-003 100 47871 90136-1 PDQ (3 units) 7.75 x 6 x 11.75 3 lbs 108 972 lbs

900-0136-020 200 47871 90136-8 Master Pack (20 units) 16 x 24 x 12 20 lbs 12 240 lbs

21007387 400 47871 90136-2 4pc Tray and Lid 7.75 x 9.25 x 11.75 4 lbs 75 300 lbs

21008697 100 47871 08697-6 Gift Box, 6pc Master Pack 6 x 13 x 6.25 6 lbs 144 872 lbs

Distributed by:

1016 Corporate Park Drive
Mebane NC 27302
1-800-880-6788
www.Kidde.com

P/N: KL-i9010 sheet rev. 11-2011