Kidde I12010SCO Brochure

Worry-Free AC Wire-in Combination

10

Smoke & Carbon Monoxide (CO) Alarm

Sealed Lithium Battery Backup

Model i12010SCO

Sealed 3V Lithium Battery Backup

10-year* tamper proof battery eliminates need for battery replacement.
Alerts user to replace alarm after 10 years of operation.

Voice Warning

Warns of hazard by announcing “Fire!” or “Warning, Carbon Monoxide.”

Intelligent Sensor Technology

Reduces nuisance alarms and offers fast response to real fires.

Test/Hush Button Functions

A single button that tests alarm circuitry and temporarily silences nuisance alarms.

Two LED Display

Red LED indicates alarm mode, Green LED indicates AC power is present

Peak Level Memory

Alerts user when the unit has detected CO
concentrations of 100ppm or higher.

Description

The Kidde i12010SCO is a hardwired combination smoke and
carbon monoxide alarm that contains a 10-year, sealed battery
backup. This alarm uses breakthrough technology to offer a fast
response to real fires, including smoldering and fast-flaming,
as well as protect you from carbon monoxide and dramatically
reduce the chance of nuisance alarms. The Intelligent sensor tech­nology combines the detection capabilities of an ionization smoke
sensor – which is more likely to detect smaller, less visible fire
particles, like those produced by flaming fires – with that of an
electrochemical sensor, which is used to detect CO. Since carbon
monoxide is present in all fires, having both detection chambers
work together in one alarm is a breakthrough in the fire safety
industry. When either sensor notices a potential hazard, it will
communicate with the other. Depending on what is detected, the
alarm will adjust its smoke sensitivity in order to better discrimi­nate between a real hazard and a false one. This constant com­munication enhances the alarm’s overall performance in all fires,
and significantly reduces the potential for a nuisance alarm.

Leading authorities recommend that both ionization and photo­electric smoke alarms be installed to help insure maximum detec­tion of the various types of fires that can occur within the home.
Ionization sensing alarms may detect invisible fire particles (associ­ated with fast flaming fires) sooner than photoelectric alarms.
Photoelectric sensing alarms may detect visible fire particles (asso­ciated with slow smoldering fires) sooner than ionization alarms.

The i12010SCO contains a 10-year tamper proof backup battery
that eliminates the need for battery replacement, and ends worry
over unauthorized battery removal. The alarm provides continuous
protection from smoke, fire and carbon monoxide, even during
power outages. At the end of alarm life, the unit will chirp, indi­cating the alarm is in need of replacement. The end of life chirp
can be temporarily silenced, allowing for replacement at a more
convenient time.

Features and Benefits

• Sealed-In Lithium Battery Backup – no battery replacement
required over the 10 year life of the alarm. Eliminates worry
about removal or unauthorized deactivation of alarm.

• Voice Warning System – Verbally announces “FIRE!” or
“WARNING! CARBON MONOXIDE” to help distinguish
between threats.

• Smart Interconnect – Interconnects up to 24 Kidde devices
(of which 18 can be initiating)

• Hush Feature – Temporarily silences nuisance alarms for
approximately 9 minutes and will not allow hush mode unless
the unit is in alarm mode.

• Peak Level Memory – Announces “CARBON MONOXIDE
PREVIOUSLY DETECTED” if alarm has detected CO level of
100ppm or higher since it was last reset.

• Ionization Sensing Technology – Ideal for detecting fast
flaming and other types of fires.

• Green LED – Illuminates to indicate the unit is receiving AC
power. Flashes once every 60 seconds to indicate battery only
mode. Flashes once per second during alarm to indicate initiating
alarm. Flashes once every 16 seconds to indicate smoke or CO
previously detected. Flashes every 2 seconds while the alarm is in
HUSH mode.

• Red LED – When a dangerous level of smoke or carbon monox­ide is detected the red LED will flash. If the unit malfunctions, the
red LED will flash and the unit will chrip every 30 seconds..

*

Worry-Free 120V AC Wire-in
Combination Smoke & Carbon Monoxide Alarm

Sealed Lithium Battery Backup

Model i12010SCO

Architectural and Engineering
Specifications

The combination smoke and carbon monoxide alarm shall be Kidde model
i12010SCO or approved equal. It shall be powered by 120VAC, 60Hz source with
on 3V sealed lithium battery backup. The temperature operating range shall be
between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operating range shall be
10% - 95% relative humidity, non-condensing.

The unit shall incorporate an ionization smoke sensor with nominal sensitivity of

0.50-1.22%/ft. The CO sensor shall be of a fuel cell design and shall meet the sensi­tivity requirements of Underwriters Laboratories UL2034 Single and Multiple Station
Carbon Monoxide Detectors.

The combination alarm can be installed on the surface of any wall or ceiling follow­ing the UL/NFPA/Manufacturer’s recommended placement guidelines. The alarm
can be installed on any standard single gang electrical box, up to a 4” octagon
junction box. The electrical connection (to the alarm) shall be made with a plug-in
connector. The unit shall provide optional tamper resistance that deters removal of
the unit from the wall or ceiling. No additional pieces shall be required to activate
this feature.

A maximum of 24 Kidde devices can be interconnected in a multiple station
arrangement. The interconnect system must not exceed the NFPA (National Fire
Protection Association) limit of 18 initiating devices, of which 12 can be smoke
alarms. With 18 initiating devices (smoke, heat, CO, etc), interconnected, it is still
possible to interconnect 6 strobe lights and or relay modules.

The alarm shall include a test button that will electronically simulate the presence of
smoke and CO and cause the unit to go into both modes of alarm. This sequence
tests the unit’s electronics to ensure proper operation.

The CO sensor will not alarm to levels of CO below 30 ppm and will alarm in the
following time range when exposed to the corresponding levels of CO.

70 ppm CO Concentration 60 – 240 minutes
150 ppm CO Concentration 10 – 50 minutes
400 ppm CO Concentration 4 – 15 minutes

The combination alarm shall have two methods of warning for danger: a piezoelec­tric horn that is rated at 85 decibels at 10 feet and a voice warning that identifies
the danger. For a CO incident, the horn will sound in the repetitive manner – four
(4) fast beeps, a short pause, four (4) fast beeps, a short pause. In between, the unit
will announce “Warning Carbon Monoxide!” In a Smoke incident, the horn will
sound in the repetitive manner – three (3) beeps, a pause, three (3) beeps, a pause.
In between, the unit will announce “Fire!”

The unit shall incorporate 2 LED’s. A green LED will be steady on when AC power
is present, flash every 60 seconds when in the battery only mode, every second to
indicate alarm memory, and every 2 seconds to indicate the Hush“ mode is active.
A red LED will flash in unison with the sounder pattern.

The unit shall include the Hush
minutes if a nuisance alarm condition occurs. The Green LED on the alarm will flash
every 2 seconds while in HushTM and will automatically reset itself. It also provides
voice annunciation of “Hush Mode Activated” when HushTM is activated and “Hush
Mode Cancelled” when the Hush cycle ends.

The unit shall also indicate a low battery warning utilizing each of the following
methods: a brief alarm chirp, the voice announcement of “Low Battery!”

The unit shall at a minimum meet the requirements of UL 2034, UL217, NFPA72,
(chapter 11 2002 edition) The State of California Fire Marshall, NFPA101 (One
and two family dwellings) Federal Housing Authority (FHA), Housing and Urban
Development (HUD). It shall also include a 10-year manufacturer’s limited warranty.

TM

feature that silences the unit for approximately 9

Installation of Smoke Alarm

The combination alarm should be installed to comply with all local codes
having jurisdiction in your area, Article 760 of the National Electric Code,
and NFPA 72. Make certain all alarms are wired to a single, continuous
(non-switched) power line, which is not protected by a ground fault
interrupter. A maximum of 1000 ft. of wire can be used in the intercon­nect system. Use standard UL listed household wire (18 gauge or larger
as required by local codes).

FUSE OR CIRCUIT BREAKER

L
N

BLACK

First
Alarm

WHITE

RED

Additional
Alarms

Technical Specifications

Power Source:
Saled lithium battery backup

Smoke Sensor: Ionization

CO Sensor: Electrochemical

Audio Alarm: 85dB at 10ft

Temperature Range: 40˚F (4.4˚C) to 100˚F (37.8˚C)

Humidity Range: 10%-95% relative humidity,
non-condensing

Size: 5.5” in diameter x 1.75” depth

Weight: 1lb

Wiring: Quick connect plug with 6” pigtails

Interconnects: Up to 24 Kidde devices
(of which 18 can be initiating)

Warranty: Ten year limited

120VAC, 60Hz 45mA max per alarm

5.5” 1.75”

Ordering Information

Ordering Pack Pack Dimensions Cartons/
Number UPC I2F5 Config. Quantity (w x d x h inches) Weight Pallet

Not for sale by individual unit

21010408 0-47871-10408-6 100-47871-10408-3 BOX Master Pack (6 Units) 6.0 x 13.0 x 6.0 2.7 126

Distributed by:

1016 Corporate Park Drive
Mebane NC 27302
1-800-880-6788
www.Kidde.com

KL-i-AC/DCCombo sheet rev. 02-2014