Page 1
HEAT ALARM FEATURES
• This heat alarm is powered from a 230V AC supply, and has
a 9V DC battery back-up source. AC/DC heat alarms offer added
protection in the event of a power failure or a flat battery.
• Unique power connector prevents interconnecting with incompatible heat alarms, smoke alarms, or security systems.
• This Model H230 heat alarm can be interconnected with as many as
35 other heat alarms of the same model, or Firex 230V AC smoke
alarms. Interconnectable Firex smoke alarms include: GC240, I240C,
IAR230C, PG240, PAD240, PADC240 and PAR230.
©1998 Maple Chase Company
57°C FIXED TEMPERATURE
MODEL H230
PLEASE READ AND SAVE
THIS MANUAL
Installer: Please leave this manual with
the occupier (or, in the case of a house
in multiple operation, with the owner)
CONTENTS
p.1-2 Heat Alarm Features
p.2 Specifications
p.2-3 Important Safety Information
p.4 Heat Alarm Location
p.5 Heat Alarm Siting
p.5-6 How To Install This Heat Alarm
p.7 Interconnecting Heat Alarms
p.7 Red and Green Led Indicators
p.8 Testing the Heat Alarm
p.8-9 Maintenance and Cleaning, Battery Replacement, Repair
p.10 Fire Safety Rules and Preventing Hazardous Situations
p.10-11 Fire Procedure
p.11 What to Do in Case of Fire
p.11-12 Troubleshooting
p.12 Guarantee
!WARNING: HEAT ALARMS ALONE ARE NOT SUFFICIENT FOR LIFE SAFETY AS THEY ARE NOT
DESIGNED TO DETECT SMOKE
. THEY ARE INTENDED TO DETECT TEMPERATURES OF 57° C TO
PROVIDE AN ADDITIONAL SOURCE OF INFORMATION THAT IS SUPPLEMENTARY TO THAT PRO
-
VIDED BY SMOKE ALARMS TO INCREASE THE PROBABILITY THAT AN EARLY WARNING WILL BE
PROVIDED AND SO ENHANCE LIFE SAFETY AND PROPERTY PROTECTION
. SEE “HEAT ALARMS HAVE
LIMITATIONS
” IN THE IMPORTANT SAFETY INFORMATION SECTION OF THIS MANUAL.
230V AC
with 9V Battery
Back-up
110-607
1 2 3 4 5 6
Heat Alarm
®
Page 2
• Optional use tamper-resistant feature serves as a safeguard against
tampering.
• Unique “battery missing” device. The heat alarm will not attach to
the mounting bracket if a battery is not in the battery compartment.
• The heat alarm will sound a short beep about once a minute if the
battery is low or improperly connected.
• Multi-purpose green and red LEDs indicate that the heat alarm is connected to the AC supply, is working normally, or is in alarm.
• Loud alarm sounder – 85 decibels [dB(A)] at 3m – will sound to alert
you of an emergency.
• Test button checks heat alarm operation.
SPECIFICATIONS
UMBER H230
MODEL N
ATING 230V AC, 9 VOLT DC BATTERY BACKUP
ELECTRICAL R
INTERCONNECTING FIREX UP TO ANY COMBINATION OF 35 OTHER FIREX HEAT
SMOKE AND HEAT ALARMS ALARMS (MODEL H230) OR FIREX SMOKE ALARMS
OR PATTRESS WITH RELAY)(MODELS GC240, I240C, IAR230C, PG240,
(
TEMPERATURE RATING 57°C FIXED TEMPERATURE
MBIENT 37.8°C
MAXIMUM A
UNIT
TEMPERATURE AT
OPERATING TEMPERATURE -23°C TO 70°C
RECOMMENDED COVERAGE 50M
RECOMMENDED SPACING 5.3M
MAXIMUM DISTANCE FROM WALL 7.7M
MAXIMUM CEILING HEIGHT
IMPORTANT SAFETY INFORMATION
PLEASE READ AND SAVE THESE INSTRUCTIONS
!WARNING
• This heat alarm requires constant 230V AC power AND a healthy
9V DC battery to operate properly. This heat alarm WILL NOT work if
AC power is not connected, or has failed or been interrupted for any
reason, AND the batteries have been removed or are flat or improperly connected. DO NOT use any other kind of battery except as
specified in this manual. DO NOT interconnect this heat alarm to
any other type of smoke alarm or heat alarm or auxiliary device,
except those listed in this manual.
• The Push-to-Test button accurately tests all heat alarm functions.
DO NOT use any other test method for routine testing. Test heat
alarm weekly to ensure proper operation.
• Higher ceilings will increase the time needed by the heat alarm to
detect a fire. In most dwellings the ceiling height will keep this reaction time within acceptable limits. However, ceilings with a height of
over 6m may delay the reaction time of the heat alarm significantly.
PAD240, PADC240
N
OTE
INTERCONNECTED WITH
ODEL PATR). HOWEVER, A MAXIMUM COMBINA-
(M
TION OF 12 OF THESE MODELS (FIREX SMOKE AND
EAT ALARMS AND
H
INTERCONNECTED AT ONE TIME
6M
: T
2
HE ABOVE
AND PAR230)
FIREX MODELS MAY BE
ATTRESS WITH RELAY
FIREX P
PATTRESS WITH RELAY) MAY BE
.
Page 3
Advice from your local distributor or Fire Brigade should be
obtained when installing a heat alarm on a ceiling higher than 6m.
• This heat alarm should be installed only by a qualified electrician.
The installation should comply with BS 7671 and all prevailing local,
regional and national codes.
• This heat alarm is designed to be used only as part of the protection
of a single family dwelling or a house in multiple occupation (HMO)
of no more than two stories. It may also be used in conjunction with
smoke alarms within individual flats or apartments in larger houses
in multiple occupation, to provide an early warning to occupants
of a fire in a room within the dwelling, but a communal fire alarm
system should also be provided in such cases. DO NOT install this
heat alarm in any other buildings, such as hotels, motels, dormitories, hospitals, nursing homes or group homes of any kind. In these
occupancies, a complete automatic fire detection and alarm system,
complying with BS 5839: Part 1, should be installed.
• Heat alarms should only be used in conjunction with smoke alarms,
with which the heat alarms should be interconnected, in order to
provide early warning of heat, smoke, or fire. Smoke alarms should
be installed on every level of the dwelling.
• Interconnected heat alarms and smoke alarms offer maximum protection. By interconnecting heat alarms and smoke alarms, when
one unit senses heat, smoke, or fire, and sounds its alarm, all others
will sound as well. DO NOT connect this heat alarm to any other
type of alarm (except those stated in this manual) or approved
auxiliary device.
• Heat alarms interconnected with smoke alarms may not alert every
household member every time. The alarm sounder of the heat alarm
is loud in order to alert individuals of a potential danger. However,
there may be limiting circumstances where an occupant may not
hear the alarm (e.g. outdoor or indoor noise, sounder sleepers, drug
or alcohol usage, impaired hearing, etc.) Household members must
hear the alarm’s warning sound and quickly respond to it to reduce
the risk of damage, injury, or death that may result from fire.
• Check carefully that, when any one device operates, the alarm
signal given by interconnected devices is clearly audible throughout
the building, particularly in bedrooms, where it is essential that
the alarm signal will wake sleeping occupants.
• This heat alarm can only sound an alarm when it detects temperatures of 57°C or above. Heat alarms do not sense smoke or gas.
In some fires, hazardous levels of toxic chemicals and smoke can
build up before a heat alarm will operate. Temperatures may not
reach 57°C to activate the heat alarm QUICKLY ENOUGH to ensure
safe escape.
• Some fires are slow smouldering, low heat-producing, or are in a
different room to that in which the heat alarm is located, or the heat
from the fire may bypass the alarm – the heat alarm may not give a
warning under these circumstances.
• Heat alarms have limitations. This heat alarm is not guaranteed to
protect lives or property. Heat alarms are not a substitute for insurance. Householders should insure their lives and property. In addition, as with any electronic device, it is possible for the heat alarm
to fail at any time.
• Never paint this heat alarm.
Page 4
HEAT ALARM LOCATION
Heat alarms give an audible warning when the temperature at the alarm
reaches 57°C. Heat alarms are ideal for kitchens, garages, cellars, boiler
rooms, attics and other areas where there are normally high levels of
fumes, smoke or dust which preclude the use of smoke alarms due to
the risk of false alarms.
Guidance on fire detection in dwellings is contained in BS 5839: Part 6.
For normal-sized bungalows, two-story houses, flats and maisonettes, the
British Standard recommends that the minimum level of protection should
comprise smoke alarms in the hallways and staircases. This minimum
standard necessitates one smoke alarm in the hallway of a typical bungalow or one smoke alarm on each level of a two-story house. Heat alarms
should not be used in these circulation areas. If there are, for example,
long hallways, even the minimum standard may necessitate additional
interconnected smoke alarms.
If, however, the design of the dwelling does not comply with modern fire
safety standards, or if factors such as the presence of several young
children, of elderly occupants or disabled people, or of smokers, the use
of portable heaters or solid fuel fires during the night, or the use of electric blankets, particularly by the elderly, the British Standard advises that
additional detection devices, installed within rooms, may be necessary.
The British Standard recommends that, if the risk justifies the provision of
detectors in a kitchen, boiler room, or other area (except a circulation area)
in which smoke alarms would be likely to give false alarms, heat alarms
should be used. However, the Standard also advises that heat alarms
may be installed in other rooms instead of smoke alarms, provided that
the construction enclosing the room (including the door) can resist fire
for a sufficient time after operation of a heat alarm to enable occupants
to escape safely. However, a heat alarm is unlikely to operate early enough
to save the life of anyone asleep in the room in which it is installed.
Moreover, a heat alarm in the room of fire origin may not give sufficient
warning for occupants to escape safely if the door to that room is open.
HEAT ALARM
UNFINISHED ATTIC
SMOKE ALARM
SMOKE ALARM WITH
FALSE ALARM CONTROL
BEDROOM
BOILER ROOM
BEDROOM
KITCHENLIVING ROOM
UTILITY/
LAUNDRY
GARAGE
Page 5
HEAT ALARM SITING
FOR BEST PROTECTION, IT IS RECOMMENDED THAT YOU INSTALL A
SMOKE OR HEAT ALARM IN EVERY ROOM. In addition, it is recommend-
ed that all smoke and heat alarms should be interconnected.
Install heat alarm on a standard electrical box or surface mount pattress
(Firex Model PAT or PATR) as close to the centre of the ceiling as possible. If the centre is not practical, mount the heat alarm no closer than
300mm away from a wall or corner.
In rooms with open joists or beams, all ceiling-mounted alarms should
be located on the bottom of such joists or beams and not up in joist
channels. On sloped, peaked or gabled ceilings, install heat alarm 90cm
from highest point. If only wall placement is possible, install no further
than 150mm from ceiling.
DO NOT install heat alarms:
• Directly over the cooker, stove or oven.
• In areas with high humidity, like bathrooms or shower rooms, or
areas near dishwashers or washing machines. Install heat alarms
at least 3m away from these areas if possible.
• Adjacent to, or directly above, heaters, air-conditioning vents or
ceiling fans.
• In an area where the temperature may fall below -23°C or rise
above 37°C.
• Near fluorescent lights. Electrical ”noise” and flickering may affect
the operation of the heat alarm.
• Closer than 300mm to light fittings.
• In such a position that it is difficult or dangerous to reach for testing, maintenance or battery replacement.
HOW TO INSTALL THIS HEAT ALARM
!DANGER: ELECTRIC SHOCK HAZARD
AT THE MAIN DISTRIBUTION BOARD BY REMOVING THE FUSE OR SWITCHING THE CIRCUIT
BREAKER TO THE
OFF POSITION AND SECURING IT
!WARNING: T
HIS HEAT ALARM SHOULD BE INSTALLED ONLY BY A QUALIFIED ELECTRI
CIAN IN ACCORDANCE WITH THE REGULATIONS FOR ELECTRICAL INSTALLATIONS PUB-
INSTITUTION OF ELECTRICAL ENGINEERS (BS 7671) AND/OR ALL
LISHED BY THE
PRESIDING LOCAL
, REGIONAL AND NATIONAL CODES.
EAT ALARMS SHOULD BE CONNECTED ON A SINGLE INDEPENDENT
!WARNING: H
CATED CIRCUIT AT THE MAIN DISTRIBUTION BOARD. NO OTHER ELECTRICAL EQUIPMENT,
EXCEPT COMPATIBLE SMOKE ALARMS
HOME HAS RESIDUAL CURRENT DEVICE PROTECTION ON THE ELECTRICAL INSTALLATION OR
ON INDIVIDUAL CIRCUITS
FAULTS ON CIRCUITS SERVING SOCKET OUTLETS OR PORTABLE APPLIANCES CANNOT
CAUSE INTERRUPTION TO THE SUPPLY TO THE HEAT ALARMS
HEAT ALARMS MAY ALSO BE CONNECTED TO A SEPARATE ELECTRICALLY
REGULARLY-USED LOCAL LIGHTING CIRCUIT. HOWEVER, THIS WILL MEAN THAT, UNLESS A
SEPARATE MEANS OF ISOLATION IS PROVIDED FOR THE HEAT ALARMS
SARY TO ISOLATE THE LIGHTING CIRCUIT EVERY TIME THAT THERE IS A NEED TO ISOLATE
THE SUPPLY TO THE HEAT ALARMS
1. Route the household AC supply/interconnect cable into the electrical accessory box or surface Pattress (Firex Model PAT or PATR).
2. Using a suitably-rated connector (supplied with Firex Pattress models)
connect the neutral supply to the blue lead of the connector plug.
. T
URN OFF POWER TO THE HEAT ALARM CIRCUIT
.
, SHOULD BE CONNECTED TO THIS CIRCUIT. IF YOUR
CHECK WITH A QUALIFIED ELECTRICIAN TO MAKE SURE THAT
,
; THIS MAY CAUSE INCONVENIENCE OR HAZARDS.
.
-PROTECTED,
, IT WILL BE NECES-
, DEDI-
-
Page 6
STANDARD ELECTRICAL BOX OR
(MODEL PAT OR PATR) PATTRESS
CEILING
NEUTRAL
INTERLINK
LINE
BLUE
BROWN
ORANGE
FIREX MODEL H230
3. Using a suitably-rated connector (supplied with Firex Pattress models)
connect the line supply to the brown lead of the connector plug.
4. If interconnecting is desired, connect the orange of the connector
plug to the designated interconnect conductor of the household
cable. See note “INTERCONNECTING HEAT ALARMS”.
5. Insert the completed connector block onto the mounting pins of the
Firex Pattress or recess into the electrical accessory box.
6. Pass the connector plug through the mounting plate of the heat
alarm, align slots and fasten mounting plate securely to the Firex
Pattress or electrical accessory box.
NOTE: If this is to be a single-station heat alarm, cover the orange wire
with electrical tape and tuck it into the electrical box or pattress.
7. Open the battery compartment door.
8. Connect a new, healthy 9V DC battery to the battery connector
inside the battery compartment. Be sure the battery is securely
connected. The heat alarm may beep briefly when the battery
is installed.
9. Close the battery compartment door, snapping it into place.
10. Attach the connector plug to the pins on the back of the heat alarm.
The plug will only fit one way, and will snap into place.
11. Gently tug the connector to be sure it is attached securely.
12. Position the heat alarm on the mounting plate and turn it clockwise
to lock it into place.
13. Test the heat alarm to verify the 9V DC battery back-up. See
“TESTING THE HEAT ALARM”.
NOTE: The heat alarm will not mount to the plate if the battery is not
in place.
14. Turn on the power to the heat alarm circuit at the main distribution
board.
15. Test the heat alarm for AC operation. See “TESTING THE HEAT
ALARM”.
Page 7
INTERCONNECTING HEAT ALARMS
Use 1.5mm2minimum solid or stranded cable with a rating of 230V. When
interconnecting heat alarms and/or smoke alarms, the maximum cable
length between any two should be 450m for 1.5mm2cable (20 ohm loop
resistance.)
This heat alarm may be interconnected with as many as 35 other
Firex Model H230 heat alarms or model GC240, I240C, IAR230C, PG240,
PAD240, PADC240 or PAR230 smoke alarms. DO NOT connect to any
other type of model of heat alarm or smoke alarm. If interconnecting to
Firex Pattress with Relay (Model PATR) only 12 total Firex models may
be interconnected.
Connect all interconnected heat and smoke alarms to a single final circuit. Wiring must conform to I.E.E. Regulations for Electrical Installations
(BS 7671).
RED AND GREEN LED INDICATORS
This heat alarm features a red and green LED indicator that can be seen
through the clear light pipe on the top of alarm. The LEDs indicate the
following:
GREEN
ON – AC power is present.
OFF – AC power is not present.
RED
BLINKS ONCE A MINUTE – DC power is present indicating
normal operation.
OFF – DC power is not present.
BLINKS ONCE A SECOND and unit is sounding alarm – senses
57°C temperature or greater.
OFF and unit is sounding alarm – Another interconnected
smoke/heat alarm in the network has sensed smoke or 57°C
and is signaling this alarm.
7 8 9 10 11 12
NOTE: Colors shown correspond to electrical codes in the United Kingdom.
Colors may vary in other countries.
BLUE BLUE
ORANGE ORANGE
BROWN BROWN
FOR INTERCONNECTING: USE A MINIMUM OF 1.5mm2 CABLE
NEUTRAL
LINE
Page 8
TESTING THE HEAT ALARM
!WARNING: TEST EACH HEAT ALARM AND SMOKE ALARM TO BE SURE THAT EACH IS
INSTALLED CORRECTLY AND IS OPERATING PROPERLY
’S LENGTH FROM THE HEAT ALARM WHEN TESTING. THE ALARM SOUNDER
TAND AT A RM
S
IS LOUD TO ALERT YOU TO AN EMERGENCY AND CAN BE HARMFUL TO HEARING
EST THE HEAT ALARM WEEKLY AND UPON RETURNING FROM HOLIDAY, OR WHEN THE
T
HOUSE HAS BEEN UNOCCUPIED FOR SEVERAL DAYS
Test all heat alarms weekly by doing the following:
1. Check the Push-to-Test button. A constant ON green light indicates
the heat alarm is receiving AC power.
2. Firmly depress the Push-to-Test button for at least five (5) seconds.
The heat alarm will sound a loud beep for about four (4) times a
second. The alarm may sound for up to ten (10) seconds after the
Push-to-Test button is released. NOTE: If heat alarms are interconnected, all heat alarms should sound an alarm within three (3)
seconds after any test button is pushed and the tested heat
alarm sounds.
3. If the heat alarm does not sound, turn off the power to the heat
alarm circuit at the main distribution board and check the wiring.
Retest the heat alarm.
!WARNING: IF THE HEAT ALARM SOUNDS, AND THE HEAT ALARM IS NOT BEING TESTED,
THE HEAT ALARM IS SENSING A TEMPERATURE OF 57°C OR ABOVE. THE ALARM
SOUND REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.
.
.
.
MAINTENANCE AND CLEANING
In addition to weekly testing, this heat alarm must be cleaned periodically
to remove dust, dirt and debris. The battery must also be replaced annually.
!DANGER: ELECTRIC SHOCK HAZARD.
URN OFF THE AC SUPPLY TO THE HEAT ALARM AT THE MAIN DISTRIBUTION BOARD
T
BY REMOVING THE FUSE OR SWITCHING THE APPROPRIATE CIRCUIT BREAKER TO THE
POSITION BEFORE REPLACING THE BATTERY OR CLEANING THE HEAT ALARM
OFF
.
BATTERY REPLACEMENT
Always turn off the AC power to the heat alarm before replacing the battery. Replace the battery at least once annually, or immediately when the
low battery signal sounds once a minute, even though the heat alarm is
receiving AC power.
Use only the following batteries as replacements in this heat alarm:
Eveready 216, 522,1222, Duracell MN1604 or Ultralife UL9V-J.
O NOT USE ANY OTHER TYPE OF BATTERY
!WARNING: D
MANUAL
. DO NOT USE RECHARGEABLE BATTERIES
1. Turn off the AC power supply to the heat alarm at the main
distribution board.
2. Insert a small screwdriver into the slot in the mounting plate and
turn the heat alarm counterclockwise to detach the alarm.
3. Gently pull down the heat alarm. Be careful not to separate any
wire connections.
, EXCEPT AS SPECIFIED IN THIS
.
Page 9
4. Pull out the connector plug from the back of the heat alarm.
5. From the back of the heat alarm, remove battery door screw and
lift the tab to open the battery compartment door.
6. Remove the battery from the compartment. Disconnect the
drained battery from the battery compartment and discard.
7. Connect a new, healthy 9V battery to the connector. The battery
will only fit one way. Be sure the battery connector is securely
attached to the battery terminals.
8. Place the battery into the battery compartment.
9. Close the battery compartment door. Push down until it snaps
into place. Install battery door screw.
10. Using the Push-to-Test button, test the heat alarm to verify 9V DC
battery back-up. See “TESTING THE HEAT ALARM”.
11. Replace the connector plug. The connector will “snap” into place.
Gently tug the connector to be sure it is attached properly.
12. Reattach the heat alarm to the mounting plate by turning the heat
alarm clockwise until it snaps into place.
13. Turn on the AC power and test the heat alarm using the
Push-to-Test button. See “TESTING THE HEAT ALARM”.
!WARNING: HEAT ALARMS ARE LIFE-SAVING DEVICES AND SHOULD BE CARED FOR
PERIODICALLY
.
CLEANING
Clean the heat alarm at least once annually to remove dust, dirt
and debris. Always turn off the AC power to the heat alarm before
cleaning it.
Using the soft brush or wand attachment to a vacuum cleaner,
vacuum all sides and the cover of the heat alarm. Be sure that all
vents are free from debris.
If necessary, turn off the AC power and use a damp cloth to clean the
heat alarm cover.
IMPORTANT: Do not attempt to remove the cover or clean inside the
heat alarm. THIS WILL INVALIDATE YOUR GUARANTEE. Failure to properly clean and maintain this heat alarm may result in impaired operation
and possible failure and will invalidate the guarantee.
REPAIR
!CAUTION: DO NOT ATTEMPT TO REPAIR THIS HEAT ALARM
DATE YOUR GUARANTEE
If the heat alarm is not operating properly, see “TROUBLESHOOTING”.
If necessary, and if the heat alarm is still under guarantee, return it to
your local distributor. Pack it in a well-padded carton and send it, postage
prepaid, to one of the addresses given at the end of this manual.
If the heat alarm is no longer under guarantee, have a qualified electrician replace the heat alarm immediately with a comparable Firex brand
heat alarm.
.
. DOING SO WILL INVALI
-
Page 10
FIRE SAFETY RULES AND PREVENTING
HAZARDOUS SITUATIONS
Siting, testing, and taking care of heat and smoke alarms is just one step
in helping to protect your family and home from fires. You must also
reduce the chance that fires will start in your home and increase your
chances of escaping if a fire does start. For your safety, as a minimum,
you should do the following to have more effective fire safety.
• Use smoking materials properly – never smoke in bed or when
sleepy or under the influence of alcohol or other drugs.
• Keep matches and other sources of ignition away from children.
• Store flammable materials in proper containers and never store or
use them near open flames or sparks.
• Keep electrical appliances and their leads in good working condition, and do not overload electrical circuits.
• Keep fireplaces, chimneys, and barbecue grills clean, and make
sure they are properly sited away from combustible materials.
• Keep portable heaters and open flames such as candles away from
combustible materials.
• Do not allow rubbish to accumulate.
• Have the electrical wiring in your house checked by a qualified
electrician at least every 10 years (or more often as it ages).
• Never leave cooking unattended.
FIRE PROCEDURE
If you hear the heat or smoke alarm sounding, and you have not pushed
the test button, it is warning you of a dangerous situation. You will need to
respond immediately. To prepare for such occurrences, develop family
escape plans, discuss them with all household members, and practice
them regularly. For your safety, as a minimum, you should do the following
to have more effective fire safety.
• Draw a floor plan of your home and find all ways to escape if there is
a fire. On the ground floor, consider whether windows can be used
for escape. On upper floors, consider whether external rescue will
be possible if escape routes are cut off by fire or smoke.
• Expose everyone to the sounds of the heat alarm and of the smoke
alarm and explain what the sounds mean. Show them how to check
to see if doors are hot before opening them, how to stay close to
the floor and crawl along the floor to stay below dangerous smoke,
fumes and gases, and how to use the alternative exit if a door is hot.
Instruct them not to open the door if the door is hot.
• Decide on a meeting place a safe distance from your house and
make sure all members of your household understand they should
go and wait for you there if there is a fire. Explain to children that
they must be ready to leave the house by themselves if necessary.
Page 11
• Hold fire drills every six (6) months to make sure everyone, even
small children, know what to do to escape safely.
• Know where to go to call the Fire Brigade from outside your house.
• Provide emergency equipment, such as fire extinguishers, and teach
your family how and when to use this equipment.
WHAT TO DO IN CASE OF A FIRE
After you have prepared family escape plans and practiced them with
your family, you have increased their chances of escaping safely. Review
the following rules with your children when you have fire drills, so everyone will remember them in a real fire.
1. Don’t panic, stay calm. Your safe escape may depend on thinking
clearly and remembering what you have practiced.
2. Get out of the house, following your planned escape route,
as quickly as possible. Do not stop to collect anything or to
get dressed.
3. Open doors carefully only after feeling to see if they are hot. Do
not open a door if it is hot; use an alternative escape route. If
your escape route is cut off, go to a window and shout for help.
If necessary, stuff clothing or other materials in the gaps round
the room door to stop smoke entering until help arrives.
4. Stay close to the floor; smoke and hot gases rise toward the
ceiling.
5. Keep doors and windows closed unless you open them to escape.
6. Meet at your pre-arranged meeting place after leaving the house.
7. Call the Fire Brigade as soon as possible from outside your house.
Give your full address, including the name of the town or village.
8. Always call the Fire Brigade as soon as possible, even if a fire
seems small.
9. Never re-enter a burning or smoke-filled building.
These guidelines will assist you in the event of a fire. However, to reduce
the chance that fires will start, practice fire safety rules and prevent hazardous situations. Contact your local Fire Brigade for more information.
TROUBLESHOOTING
PROBLEM SOLUTION
Heat alarm does not 1. Check that AC power is
sound when tested. turned on.
NOTE: Push test button for plate and:
at least five (5) seconds a. Check that connector
while testing! plug is securely attached.
2. Turn off power. Remove
heat alarm from mounting
b. Check that battery is
properly attached to
connector.
3. Clean heat alarm.
Page 12
PROBLEM SOLUTION
Heat alarm beeps about 1. Turn off AC power and
once a minute. replace battery. See
Heat alarm sounds 1. Hire an electrician to move
unwanted alarms. heat alarm to a new location.
Interconnected heat alarms 1. Press and hold button for at
do not sound when system least three seconds after the
is tested. first unit sounds.
“Battery Replacement” in
the “MAINTENANCE AND
CLEANING” section.
See the “HEAT ALARM
PLACEMENT” and “DO NOT
INSTALL HEAT ALARMS”
sections of this manual.
2. Turn off AC power or
circuit breaker and check
the interconnect wiring.
See “INTERCONNECTING
HEAT ALARMS” section
of this manual.
GUARANTEE
Maple Chase Company (the “Company”) guarantees this product (except
for the battery) to be free from defects in material and workmanship
under normal use and service (“Defects”) for a period of six (6) years from
the date of purchase (the “Guarantee Period”). Should any Defects be
discovered within the Guarantee Period, the Company will, at its option,
repair or replace the defective product provided that: (a) it is returned
during the Guarantee Period with postage prepaid and with proof of purchase date to the address shown below and (b) the Company verifies that
the claim is proper. This Guarantee does not cover damage resulting from
accident, improper installation, maintenance or repair, misuse, abuse or
product modification. This Guarantee does not confer any rights other
than those expressly set out above and does not cover any claims for
consequential loss or damage. This Guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer.
Return units, postage prepaid, to your local distributor. For information on
your local distributor, contact:
In the U.K and the Republic of Ireland, contact:
Maple Chase Company
2820 Thatcher Road
Downers Grove, IL 60515-4040 USA
Tel +1-630-719-5500
Sensotec Europe Ltd.
Unit 7, Bala Industrial Estate
Bala, Gwynedd LL23 7NL
Tel 01678 520022
Loading...