Kidde AEGIS 84-732001-001, AEGIS 84-732001-201 Installation, Operation And Maintenance Manual

P/N 06-236716-001
August 2007

Kidde AEGIS

Conventional

Fire Alarm-Suppression

™

Control Unit

Installation, Operation, and

Maintenance Manual

E

C

I

F

O

F

F

O

STATE FIRE MARSHAL

A UTC Fire & Security Company

FOREWORD

Note: This Manual, P/N 06-236716-001, is to be used by qualified and factory-trained personnel,

knowledgeable of NFPA standards and any other applicable standards in effect.

This Manual is intended to provide guidance to qualified technical professionals for the installation,
operation and maintenance of the Kidde AEGIS™ Conventional Fire Alarm-Suppression Control Unit.

Only qualified persons experienced and trained in the installation of this type of equipment should install
and configure the Kidde AEGIS. They must be familiar and experienced with the wiring diagrams and
components, electrical installation, and familiar not only with NEC, relevant NFPA and local codes but also
trained and qualified by Kidde-Fenwal, Inc. Kidde-Fenwal, Inc. is a manufacturer of the components that
make up the Kidde AEGIS system, and may not have the opportunity to visit the sites where the product
is installed or intended to be installed. It is the responsibility of the professional installer (described above)
to properly install and configure the systems. Under no circumstances will Kidde-Fenwal be liable for
improper installation or configuration of the systems.

The technical data contained herein is provided for informational purposes only, and should not be used as
a substitute for professional judgment. Although, Kidde-Fenwal believes this information to be true and
correct, it is published and presented without any guarantee or warranty whatsoever. Kidde-Fenwal
disclaims any liability for any use of the data other than as set out in this manual, foreword included.

Any questions concerning the information presented in this manual should be addressed to:
Kidde-Fenwal, Inc.

400 Main Street
Ashland, MA 01721
Phone: [phone]
Toll Free: [phone]
Technical Support: [phone]
Fax: [phone]

P/N 06-236716-001 i August 2007

TERMS AND ABBREVIATIONS

°C: °Centigrade
°F: °Farenheit

A:

AC: Alternating Current
ADA: Americans with Disabilities Act N.C.: Normally Closed

AH: Ampere Hour NEC: National Electrical Code
AHJ: Authority Having Jurisdiction NFPA: National Fire Protection Association
ARC: Automatic Release Circuit N.O.: Normally Open
AWG: American Wire Gauge NYC: New York City
CSFM: California State Fire Marshal PCB: Printed Circuit Board
DACT: Digital Alarm Comm. Transmitter pF: Pico-farads
DC: Direct Current P/N: Part Number
DET: Detector PSU: Power Supply Unit
EOLD: End of Line Device RAM: Random Access Memory
EOLR: End of Line Resistor SLC: Signaling Line Circuit
FM: Factory Mutual TB: Terminal Block
ft.: Feet UL/ULI: Underwriters Laboratories, Inc.
HSD: High Sensitivity Smoke Detector V: Volts

Ampere

LCD: Liquid Crystal Display
LED: Light Emitting Diode
MEA: Materials and Equipment Acceptance

Division of the City of New York

NAC: Notification Appliance Circuit

Hz: Hertz (Frequency) Vac: Volts AC
in.: Inch Vdc: Volts DC
IRI: Industrial Risk Insurers VRMS: Volts Root Mean Square

CAUTIONS AND WARNINGS

A caution identifies a procedure, practice, or statement, which, if not strictly followed,

CAUTION

WARNING

could result in programming errors, impairment of equipment operation, or equipment
damage.

A warning identifies an operating or maintenance procedure, practice,
condition or statement, which, if not strictly followed, could result in personal
injury or death.

August 2007 ii P/N 06-236716-001

SAFETY SUMMARY

This entire manual must be read and understood before installation.

Installation PrecautionsAdherence to the following will aid in problem-free installation with long-

term reliability:

Several different sources of power can be connected to this fire alarm control unit.

Disconnect all sources of power before servicing. Control unit and associated

WARNING

CAUTION

equipment may be damaged by servicing while the unit is energized. Do not
attempt to install, service, or operate this control unit until this manual is read
and understood.

System Re-acceptance Test after Re-Programming: To ensure proper system operation, this
system must be retested in accordance with NFPA 72 Chapter 10 after any
programming change. Re-acceptance testing is also required after any addition or
deletion of system components, and after any modification, repair or adjustment to
system hardware or wiring.

All components, circuits and system operations known to be affected by a change must
be 100% tested. In addition, to ensure that other operations are not inadvertently
affected, at least 10% of initiating devices that are not directly affected by the change,
up to a maximum of 50 devices, must also be tested and proper system operation
verified.

This system meets FM and ANSI/UL 864 requirements for operation at 32° to 120°F (0 to 49°C) and at a
relative humidity of 93% (non-condensing) @ 90°F (32.2°C). However, the useful life of the system’s
standby batteries and the electronic components may be adversely effected by continuous operation at
these environmental limits. Therefore, it is recommended that this system and its peripherals be installed
in an environment with a nominal room temperature of 60-80°F.

Like all solid state electronic devices, this system may operate erratically or can be damaged when
subjected to lightning induced transients. Although no system is completely immune from lightning
transients and interference, proper grounding will reduce susceptibility. The use of overhead or outside

aerial wiring is not recommended due to the increased susceptibility to nearby lightning strikes.

Consult with the Technical Support Department if any problems are anticipated or encountered.
Do not install electronic assemblies prior to mounting and attaching conduit for field wiring to the enclosure.

Before making modifications, verify that they will not interfere with battery and printed circuit board
locations. Do not overtighten screw terminals. Overtightening may damage threads, resulting in reduced
terminal contact pressure and difficulty with screw terminal removal.

This system contains static-sensitive components. Always ground yourself with a proper wrist strap before
handling any circuits so that static charges are removed from the body. Use static suppressive packaging
to protect electronic assemblies removed from the control unit.

Follow the instructions in this manual. These instructions must be followed to avoid damage to the control
unit and associated equipment. System operation and reliability depend upon proper installation.

Fire Alarm System Limitations While installing a fire alarm system may make lower insurance

rates possible, it is not a substitute for fire insurance!

An automatic fire alarm system – typically made up of smoke detectors, heat detectors, manual pull stations,
notification appliances, and a fire alarm control unit with remote-notification capability – can provide early warning
of a developing fire. Such a system, however, does not assure protection against property damage or loss of life
resulting from a fire.

Any fire alarm system may fail for a variety of reasons:
Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in walls,

on roofs, or on the other side of closed doors. Smoke detectors on one level also may not sense a fire on

P/N 06-236716-001 iii August 2007

SAFETY SUMMARY (CONT.)

another level or floor of a building. A second floor detector, for example, may not se nse a first floor or
basement fire.

Furthermore, all types of smoke detectors, both ionization and photoelectric types, have sensing limitations. No
type of smoke detector can sense every kind of fire caused by carelessness and safety hazards such as smoking
in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits,
children playing with matches, or arson.

Notification appliances, such as bells, may not alert people if these appliances are located on the other side
of closed or partly open doors or are located on another floor of a building.

A fire alarm system will not operate without electrical power. If AC power fails, the system will operate from
standby batteries only for a specified time.

Rate-of-Rise heat detectors may be subject to reduced sensitivity over time. For this reason, the rate-of­rise feature of each detector should be tested by a qualified fire protection specialist as recommended in
NFPA 72.

Auxiliary Equipment used in the system may not be technically compatible with the control unit. It is
essential to use only equipment listed for service with your control unit.

Telephone lines needed to transmit alarm signals from a premise to a central monitoring station may be
out of service or temporarily disabled.

The most common cause of fire alarm malfunctions, however, is inadequate maintenance. All devices and
system wiring should be tested and maintained by professional fire alarm installers following written
procedures supplied with each device. System inspection and testing should be scheduled monthly or as
required by national and/or local fire codes. Adequate written records of all inspections should be kept.

GENERAL SAFETY NOTICES The following must be observed to maintain personnel safety .

The following general safety notices supplement specific warnings and cautions appearing in the manual.
The safety precautions in this section must be understood and applied during operation and maintenance.
This manual is to be used by trained distributors/technicians. The entire manual should be read and fully
understood prior to installation.

FIRST AID

Any injury, no matter how slight, should never go unattended. Always obtain first aid or medical attention
immediately.

GENERAL PRECAUTIONS

The following general safety precautions are to be observed at all times:

1. All electrical components associated with equipment shall be installed and grounded in accordance
with NEC and local regulatory requirements.

2. Special precautionary measures are essential to prevent applying power to equipment at any time
maintenance work is in progress.

3. Before working on electrical equipment, use a voltmeter to ensure that system is not energized.

4. When working near electricity, do not use metal rulers, flashlights, metallic pencils, or any other
objects having exposed conductive material.

5. When connecting a meter to terminals for measurement, use a voltage range higher than expected
voltage to be measured.

August 2007 iv P/N 06-236716-001

NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING

JURISDICTION AND ALL OTHER INVOLVED PARTIES

This product incorporates field-programmable software. In order for the product to comply with the
requirements in the Standard Control Units and Accessories for Fire Alarm Systems, ANSI/UL 864, certain
programming features or options must be limited to specific values or not used at all as indicated below.

Abort switches may be set-up to operate in any of the following ways:

*

1. Abort Mode 1

2. Abort Mode 2 (Reset) - Reset to initial delay setting. Resume countdown for entire delay period.

3. Abort Mode 3 (IRI) - Same as Mode 1, except disable abort function if countdown timer has started.

4. Abort Mode 4 (NYC) - Resets to 120 seconds.

5. Abort Mode 5 - Disables the abort.

*

Only Abort Mode 1 is ANSI/UL 864 compliant.

(UL) - Count down to 10 seconds and hold. Resume countdown at 10 seconds.

P/N 06-236716-001 v August 2007

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 vi P/N 06-236716-001

TABLE OF CONTENTS

CHAPTER 1 GENERAL INFORMATION

1-1 Introduction ................................................................................................ 1-1

1-2 Listings and Approvals ..................................................................................1-1

1-3 Codes and Standards....................................................................................1-2

1-4 Control Unit Description ................................................................................1-3

CHAPTER 2 INSTALLATION

2-1 Installation Materials.....................................................................................2-1

2-2 Installation Guidelines...................................................................................2-2

2-3 Installation Procedure ...................................................................................2-4

2-4 Terminations And Wiring Diagrams ................................................................. 2-14

2-5 Installing the Bezel, P/N 06-220114-001 ......................................................... 2-21

2-6 Installing Optional Dead-Front Panel, P/N 06-220175-001..................................2-21

2-7 Installing the Enclosure Door (Standard Door).................................................. 2-21

2-8 Installing the Enclosure Door (Door with Switches) ........................................... 2-21

2-9 Completing the Installation............................................................................2-23

CHAPTER 3 CONFIGURATION

3-1 Entering Site - Specific Configuration ..............................................................3-1

3-2 Configuration Settings...................................................................................3-3

CHAPTER 4 OPERATION

4-1 Introduction ................................................................................................ 4-1

4-2 Control Switch Functionality...........................................................................4-2

CHAPTER 5 TESTING AND MAINTENANCE

5-1 Maintenance Requirements............................................................................5-1

5-2 Testing Frequency ........................................................................................ 5-1

5-3 Testing .......................................................................................................5-2

CHAPTER 6 TROUBLESHOOTING

6-1 Purpose ......................................................................................................6-1

6-2 Trouble Diagnostics ......................................................................................6-1

6-3 Trouble Codes and Corrective Action ...............................................................6-1

CHAPTER 7 PARTS LIST
APPENDIX A BATTERY CAPACITY CALCULATIONS

A-1 Standby Time Duration .................................................................................A-1

A-2 Power Consumption Data ..............................................................................A-1

A-3 Standby and Alarm Power Requirements .........................................................A-2

A-4 Battery Capacity Calculations.................................................................. .......A-3

APPENDIX B LIST OF AGENCY LISTED COMPATIBLE DEVICES
APPENDIX C TECHNICAL SPECIFICATIONS
APPENDIX D FM RULES FOR PREACTION/DELUGE SYSTEMS
APPENDIX E CENTRAL STATION OPERATION
APPENDIX F ROUTINGS FOR POWER-LIMITED AND NON-POWER-LIMITED WIRING

P/N 06-236716-001 vii August 2007

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 viii P/N 06-236716-001

LIST OF FIGURES

Figure Name Page Number

1-1 Control Unit Components and Dimensions...............................................................1-3

1-2 Printed Circuit Board (PCB) ...................................................................................1-5

2-1 Installation Height Above Floor..............................................................................2-4

2-2 Control Unit and Surface Mounting Dimensions........................................................2-5

2-3 Semi-Flush Mounting Dimensions................................... ........................................2-6

2-4 Trim Ring Dimensions...........................................................................................2-6

2-5 Trim Ring Installed...............................................................................................2-7

2-6 Power Supply Unit Wiring......................................................................................2-8

2-7 Power Supply Unit Installation...............................................................................2-9

2-8 PCB Installation...................................................................................................2-10

2-9 PCB-to-Cabinet Grounding Diagram........................................................................2-11

2-10 Primary Power Connections...................................................................................2-12

2-11 Backup Battery Connections..................................... ............................................. 2-13

2-12 Printed Circuit Board............................................................................................ 2-14

2-13 Initiating Device Ci rcuit Wiring...............................................................................2-16

2-14 Notification Appliance Circuit Wiring ....................................................................... 2-17

2-15 Agent Release Circuit Wiring.................................................................................. 2-20

2-16 Dead-Front Panel Installation ................................................................................2-21

2-17 Installation of Manual Release and Abort Switches....................................................2-22

2-18 Installing Switch Harness Assembly........................................................................2-23

3-1 Digital Display.....................................................................................................3-1

5-1 Battery Voltage Display .................................................................................... .... 5-2

5-2 Battery Charge Current Display ............................................................................. 5-2

E-1 Wiring for the DACT ............................................................................................. E-1

F-1 Power-Limited and Non-Power-Limited Wiring.......................................................... F-1

P/N 06-236716-001 xi August 2007

LIST OF TABLES

Table Name Page Number

1-1 Agency Listing/Approval by System Classification..................................................... 1-1

1-2 Listed/Approved Suppression Systems.................................................................... 1-2

1-3 LED Indicator and Display Color.............................................................. ............... 1-6

2-1 Kidde AEGIS Control Unit Contents.........................................................................2-1

2-2 Hardware Kit Contents (P/N 06-220147-001) .......................................................... 2-1

2-3 Wiring Gauge Recommendation, Resistance, and Maximum Lengths........................... 2-3

3-1 Configuration Settings..........................................................................................3-3

4-1 Acknowledge....................................................................................................... 4-2

A-1 Duration Time for Standby and Alarm...................................................... ...............A-1

A-2 Power Consumptions for System Components..........................................................A-1

A-3 Standby and Alarm Calculation Guide .....................................................................A-2

A-4 Battery Capacity Calculations ........................................................ ........................A-3

B-1 Detectors and Bases ............................................................................................B-1

B-2 Releasing Solenoid...............................................................................................B-2

B-3 Initiator-Based Releasing Devices ..........................................................................B-2

B-4 Miscellaneous Devices ..........................................................................................B-2

P/N 06-236716-001 xiii August 2007

General Information

GENERAL INFORMATION

1-1 INTRODUCTION

The Kidde AEGIS™ is a versatile, flexible, microprocessor-based conventional fire control unit
which can be used in a wide range of fire alarm and suppression discharge applications.

1-2 LISTINGS AND APPROVALS

The Kidde AEGIS is listed/approved with the agencies listed in Table 1-1 for system
classifications as described in the NFPA Standard 72, “National Fire Alarm Code”, ANSI/UL 864
9th edition, “Control Units for Fire Protective Signaling Systems”, and CAN/ULC-S527-99. The
Kidde AEGIS shall be implemented according to the following:

• NFPA Standard 72, “National Fire Alarm Code”

• NFPA Standard 70, “National Electric Code”

• This Installation, Operation, and Maintenance Manual (IOM)

• Any other standards enforced by a local Authority Having Jurisdiction (AHJ)
Table 1-1. Agency Listing/Approval by System Classification

CHAPTER 1

Agency System Classification

Protected Premises Fire Alarm Systems

- Protected Premises (Local) Unit

4

UL

3,4

cUL

2

FM

CSFM Fire Alarm Control Unit (Non-High Rise)

New York
City MEA

- Releasing Device Control Unit

Central Station Fire Alarm System

- Protected Premises Unit

- Releasing Device Control Unit

Protected Premises Fire Alarm Systems

- Protected Premises (Local) Unit

- Releasing Device Control Unit

(for use in buildings not required to have an annunciator)
Automatic Releases for External Systems Automatic
Central Station Signaling Systems
Local Protective Signaling

- Local

- Central Station

- Releasing Device Service

Fire Control Releasing Unit Automatic

Type

Service Signaling

Automatic
Manual
Waterflow
Sprinkler Supervisory

Automatic
Manual
Waterflow
Sprinkler Supervisory

Manual
Waterflow
Sprinkler Supervisory

Automatic
Manual
Waterflow
Sprinkler Supervisory

Manual
Waterflow
Sprinkler Supervisory

1

DAC
Non-Coded

Non-Coded

1

DAC
Non-Coded

1

DAC
Non-Coded

1

DAC
Non-Coded

1

Must be used with ANSI/UL 864 Listed/FM Approved Silent Knight DACT Model 5104B.

2

FM approved to FM requirements, ANSI/UL 864 9th edition, and CAN/ULC S527-99.

3

Per Canadian Building Code, not for use as a high-rise building fire alarm system.

4

For UL and cUL installation, must not exceed 24 hours standby and 5 minutes of alarm.

P/N 06-236716-001 1-1 August 2007

General Information

1-3 CODES AND STANDARDS

1-3.1 Suppression System Standards

The Kidde AEGIS is listed/approved for the control and activation of suppression systems listed
in Table 1-2 which the designer/installer should be familiar with.

Table 1-2. Listed/Approved Suppression Systems

Application Applicable NFPA Standard

Carbon Dioxide Extinguishing System NFPA 12
Halon 1301 Fire Extinguishing Systems NFPA 12A
Installation of Sprinkler Systems NFPA 13
Water Spray Fixed Systems for Fire Protection NFPA 15
Foam-Water Sprinkler and Foam-Water Spray Systems NFPA 16
Dry Chemical Extinguishing Systems NFPA 17
Wet Chemical Extinguishing Systems NFPA 17A
Water Mist Fire Protection Systems NFPA 750
Clean Agent Fire Extinguishing Systems NFPA 2001

1-3.2 Other Standards

The designer/installer should also be familiar with the following (as applicable):

• NFPA Standard 70, “National Electric Code

• NFPA Standard 72, “National Fire Alarm Code

• NFPA Standard 75, “Standard for the Protection of Electronic Computer/Data Processing
Equipment”

• NFPA Standard 76, “Fire Protection of Telecommunications Facilities”

• NFPA Standard 101, “Life Safety Code

• NFPA Standard 110, “Standard for Emergency and Standby Power Systems 2002 Edition”

• UL Standard 38, “Manual Signaling Boxes for Fire Alarm Systems”

• UL Standard 268, “Smoke Detectors for Fire Protective Signaling Systems”

• UL Standard 268A, “Smoke Detectors for Duct Application”

• UL Standard 1481, “Power Supplies for Fire Protection Signaling Systems”

• Underwriter Laboratories of Canada (cUL) ULC-S527-99, “Standard of Control Units for Fire
Alarm Systems”

• FM Standards 1011 and 1012, “Approval Standard for Deluge Systems and Preaction
Systems”

• FM Standard 3011, “Central Station Service for Fire Alarms and Protective Equipment
Supervision”

• Any others mandated by the building owner and/or the local Authority Having Jurisdiction
(AHJ)

®

2002 Edition”

®

2002 Edition”

®

2003 Edition”

August 2007 1-2 P/N 06-236716-001

1-4 CONTROL UNIT DESCRIPTION

The Kidde AEGIS consists of the following: Enclosure with Door, Power Supply Unit, Printed
Circuit Board (PCB), and Secondary Standby Batteries (ordered separately).

ENCLOSURE

PRINTED CIRCUIT BOARD

5 in.

(127 mm)

General Information

14-1/4 in.
(362 mm)

ENCLOSURE
DOOR

SECONDARY
STANDBY
BATTERIES

Figure 1-1. Control Unit Components and Dimensions

1-4.1 Enclosure with Door

The enclosure meets the requirements for NEMA Type 1 and is intended to be used indoors in
a relatively dust-free environment. The enclosure has a hinged door that swings open 180° for
accessibility. The enclosure can be surface or recessed mounted. A trim ring is available for
recessed mounting. The enclosure is constructed of 18 gauge sheet steel. A steel door is held
closed by a key lock. All operator interface switches and indicators are located behind the
locked cover. The enclosure is large enough to house two 12 Vdc, 12 AH batteries required for
standby operation.

1-4.1.1 ENCLOSURE DOOR OPTIONS

POWER SUPPLY UNIT
(BEHIND PRINTED CIRCUIT BOARD)

19 in.

(483 mm)

The standard enclosure door allows the operator to view the operator interface display
mounted on the PCB behind a plexiglass window. The AEGIS is also available with an alternate
door that allows an abort and manual release switch to be mounted. The manual release switch
incorporates a lift type guard and the abort switch incorporates a safety guard to prevent
inadvertent activation.

1-4.1.2 OPTIONAL DEAD-FRONT PANEL

The control unit is also suitable for mounting a dead-front panel (P/N 06-220175-001) that is
mandatory for use in Canada. The dead-front is intended to protect the user from inadvertent
access to any exposed potentially hazardous/high voltage components.

P/N 06-236716-001 1-3 August 2007

General Information

1-4.2 Power Supply Unit

The power supply unit mounts behind the circuit board and operates from either 120 Vac 50/60
Hz or 240 Vac 50/60 Hz. It powers the system and also charges a standby battery set which
provides backup in case of loss of power from the AC source.

The battery charger is capable of charging sealed lead-acid 24 Vdc batteries of capacity up to
68 AH. The charge voltage is 27.4 Vdc nominal.

The actual battery capacity used for an application is a function of the units components,
devices and configuration. Refer to Appendix A for battery capacity calculations.

The power supply monitoring circuit provides a trouble signal if any of the following occur:

• Loss of AC input or if AC power falls below 85% of nominal. This causes an immediate
change-over to battery operation and a trouble signal after 30 seconds.

• Detection of a ground fault.

• Low charging current.

• High output voltage

The battery monitoring circuit provides a trouble signal if any of the following occur:

• The battery is installed backwards.

• The battery is disconnected.

• Battery voltage falls below 19.5 V (this condition causes the battery to disconnec t and can
only be cleared when primary AC main power is restored).

1-4.3 Printed Circuit Board

The printed circuit board provides an interface or terminals for the following:

• Power Supply Unit

•Battery

• Initiating Device Circuits (System Inputs)

• System Outputs

• Operator Interface

• Auxiliary Power Output

August 2007 1-4 P/N 06-236716-001

General Information

TROUBLE

RELAY 3

RELAY 2

RELAY 1

BATT OUT

SUPERVISORY

TB7

TB8

TB9

TB10

TB11

TB12

2

SUPERVISORY
1

TB6

ABORT

TB5

MANUAL

RELEASE

WATERFLOW/
DETECTOR 3

TB3TB4

DETECTOR 2

TB2

TB1

DETECTOR 1

AC SUPPLY SELECT SWITCH (S6)

AC IN

TB13

1-4.3.1 OPERATOR INTERFACE

All alarms, troubles and supervisory signals are received at the control unit and displayed for
the operator. The Operator Interface consists of four main components and are visible and/or
audible through a transparent window:

•LED Indicators

•Control Switches

• Digital Display

• Buzzer

TB14

RELEASE 1

ARC 1

Figure 1-2. Printed Circuit Board (PCB)

RELEASE 2

ARC 2

TB16TB15

AUX

24 VDC

TB17

NAC 3

TB19

TB18

NAC 1

NAC 2

P/N 06-236716-001 1-5 August 2007

General Information

1-4.3.1.1 LED Indicators

The following is a list of control unit indicators and their LED display color.

AC Power On Green
System Alarm Red
System Supervisory Yellow
System Trouble Yellow
Signal Silenced Yellow
Agent Pre-Release Red
Agent Releasing Red
Agent Post-Release Red
Input Activated Alarm, Manual Release, and Abort — Red

Table 1-3. LED Indicator and Display Color

Indicator Display Color

Other — Yellow
Input Trouble Yellow
Release Output Trouble Yellow
NAC Output Trouble Yellow
Ground Fault Yellow
Power Supply Fault Yellow

1-4.3.1.2 Control Switches

There are four Control Switches on the Operator Interface. They are:

• Acknowledge — Silences the buzzer which sounds when a new supervisory, alarm, or
trouble is detected. Holding this control switch for five seconds, activates the control unit
Lamp Test. This control switch is also used in conjunction with the System Reset control
switch to enter the configuration mode.

Note: Microprocessor and PCB troubles are latching and cannot be silenced or reset. Refer to

Chapter 6, Troubleshooting.

• Signal Silence — Silences the NAC circuits.

• System Reset — Disconnects power from all input and output circuits and the auxiliary
output for a period of five (5) seconds. This control switch is also used in conjunction with
the Acknowledge control switch to enter the configuration mode.

• Output Disable — Disables the release of agent, and as selected in the system
configuration, the activation of NAC outputs and/or Programmable Relays. This is used
when performing maintenance on the system.

August 2007 1-6 P/N 06-236716-001

1-4.3.1.3 Digital Display

The three digit display is used for the following:

• View and enter field configuration settings

• Display troubleshooting/diagnostic codes

• Display battery voltage and charging current

• Count-down timer for agent release

1-4.3.1.4 Buzzer

The buzzer will sound when an alarm, trouble or supervisory condition is present.

1-4.3.2 INITIATING DEVICE CIRCUITS (SYSTEM INPUTS)

The Kidde AEGIS has the following system inputs:

• Three (3) Detection Inputs

• One (1) Manual Release

• One (1) Abort

• Two (2) Supervisory Inputs

General Information

1-4.3.2.1 Detection Inputs

The control unit provides two dedicated initiating/detector input circuits, plus a third that can
be used as a Waterflow alarm or an independent initiating/detector input. Inputs from these
circuits are latching. Refer to Chapter 3, Configuration for configuration settings.

Certain jurisdictions require NAC outputs due to Waterflow input to be non-silenceable. The
configuration settings in Chapter 3, Configuration allows the user to select the specific mode
needed for a given application.

Each detector circuit is suitable for Class A or Class B wiring and is capable of operating with
up to 25 smoke/electronic heat detectors and a quanti ty of contact-closure type devices (up to
the limitation imposed by wiring resistance). For a list of compatible devices, refer to
Appendix B.

1-4.3.2.2 Manual Release

Operation of a manual release pull station activates the NACs and initiates the release
sequence. The configured time delay and agent release output is activated after the site
configured time delay. Manual release overrides any other time delay. The circuit is suitable
for either Class A or Class B wiring and any quantity of contact closure type manual release
stations subject to the limitations imposed by the wiring resistance. The manual release will
also override any activated abort switch.

1-4.3.2.3 Abort

Activation of the abort station temporarily delays the impending agent release. Operation of
the abort switch during non-alarm conditions will cause a trouble signal. However, if the Abort
switch is pressed and held during either a non-alarm condition or during a first alarm condition,
and remains held until an alarm pre-release condition exists occurs, the Abort function will
execute as normal, per the configuration setting. The following abort modes are configurable.

Abort Mode 1 (ANSI/UL 864) - When the abort input is received, the release timeout
continues and stops at ten (10) seconds. If the timeout was less than ten (10) seconds when
the abort signal is received, timeout is reset to ten (10) seconds. When th e abort is released,
the timeout resumes. Successive aborts are permitted.

P/N 06-236716-001 1-7 August 2007

General Information

Abort Mode 2 (Reset) - When abort is activated, the timer is stopped and the full delay is

loaded into it. The timeout begins when the Abort control switch is released. Successive abort s
are permitted. If Mode 2 is selected with a zero (0) abort delay, the abort is disabled. Mode 2
does not comply with ANSI/UL 864s.

Abort Mode 3 (IRI) - This mode is only valid for cross-zoned release when both initiating
inputs are needed to cause the agent release activation (if selected for single zone, the abort
will be disabled). This mode is similar to Mode 1 with the exception that the abort will function
only if held after the receipt of the first alarm, but prior to the receipt of the second alarm.
Abort activation at any other time is ignored.

Abort Mode 4 (New York City) – When the abort is activated, the timer is stopped and reset
to 120 seconds. The timer will not start as long as the Abort switch is held. The timeout restarts
when the Abort switch is released. Successive Abort switch operations resets the timer back to
the full 120 second delay. Selection of this mode does not have an over-ruling effect on any
programmed manual or auto-release delays, regardless of whether an abort has actually
occurred. In this mode, the delay from a manual release is forced to zero (0), and the auto­release delay is restricted to a maximum of 30 seconds. NYC Mode does not comply with
ANSI/UL 864.

The setting of non-compliant delays with New York City Abort is not error-

WARNING

trapped or over-ruled by the control unit.

Abort Mode 5 - Disables the abort.

The circuit is suitable for either Class A or Class B wiring and any quantity of contact closure
type abort stations subject to the limitations imposed by the wiring resistance.

1-4.3.3 SUPERVISORY INPUTS

The Supervisory Circuits accept inputs from monitoring devices such as pressure switches on
agent cylinders or sprinkler systems.

1-4.4 System Outputs

The Kidde AEGIS has the following system outputs:

• Three (3) Notification Appliance Circuits (NACs)

• Two (2) Agent Release Circuits (ARC)

• Three (3) Programmable Relays

• One (1) Dedicated Trouble Relay

• One (1) Auxiliary Power Output

1-4.4.1 NOTIFICATION APPLIANCE CIRCUITS (NACs)

The AEGIS has three dedicated notification appliance circuits (NAC). Any NAC can be
configured in system configuration to operate on or more on First Alarm, Pre-Release, and
Releasing conditions. In the case that the control unit is being used in a non-suppression
application, the three NACs may be configured to operate on Alarm from DET 1, DET 2, and
DET 3. Each circuit is driven independently and is user configurable for either Class A (Style Z)
or Class B (Style Y) operation with the following coded patterns:

• 60 beats per minute (BPM)

• 120 beats per minute (BPM)

•Temporal

August 2007 1-8 P/N 06-236716-001

General Information

• Continuous
The three circuits are supervised, power-limited, and are compatible with conventional UL

listed, 24 Vdc notification appliances. They can also be used with the following synchronizable
horns and strobes:

• MT series multi-tone horns and horn/strobes

• NS series horn/strobes

• NH series horns

• RSS(P) series strobes
The MT and NS series network appliances provide the option to use silencable horns and non-

silenceable strobes on the same NAC.
Multiple NAC circuits (connected to audible devices only) programmed with the same master

code pattern are synchronized, regardless of any differing starting times that preceded their
concurrent operation.

The control unit is designed for user selection of an intelligent synchronization feature. This
feature allows the silenceable horn to be shut off while the strobe continues to flash in
synchronized fashion. Each NAC is rated 1.5A at 24 Vdc and is suitable for polarized 24 Vdc
appliances only.

The maximum number of synchronized devices is 35.

1-4.4.2 AGENT RELEASE CIRCUITS (ARC)

The AEGIS has two (2) dedicated, independently controlled Class B ARCs compatible with
devices listed in Appendix B.

The release circuit may be programmed for an ON time of 90 seconds for Control Heads and
either 10 minutes, 15 minutes or On-until-reset for Deluge/Pre-Action Solenoids. When
programmed for initiators, the ARC remains ON for 200 milliseconds.

The ARCs can be configured to activate on a variety of conditions based on inputs from manual
release, detection circuits and supervisory circuits. Activation of the ARCs can be delayed from
0 to 60 seconds (in 10 second increments) in automatic release mode. Manual Release can be
delayed from 0 to 30 seconds (in 10 second increments).

The ARCs are suitable to operate different release device types on both circui ts. In other words,
ARC1 may activate solenoids and ARC2 may activate an initiator. See Chapter 2, Installation.

ARCs are not inherently power-limited. For the circuits to be power-limited, the ARC should be field
terminated with an in-line supervisory device P/N 06-220023-001. ARCs activati ng initiators cannot
be made power-limited.

1-4.4.3 PROGRAMMABLE/DEDICATED RELAYS

The Kidde AEGIS has three independently programmable relays and one dedicated Trouble
relay. The relays are Form-C type with contacts rated 3A @ 30 VDC / 120 VAC (resistive).

P/N 06-236716-001 1-9 August 2007

General Information

1-4.4.3.1 Programmable Relays

The three programmable relays are normally in the de-energized condition and will energize
upon receipt of one of the following listed conditions. These relays will latch on change of state
and shall remain latched until manually reset by the System Reset control switch.

• 1st Alarm: (DET 1, DET 2, DET 3/WF, or Manual Release)

Note: DET 3/WF will only be active if it’s part of the activation condition.

• 1st Alarm: (DET 1, DET 2, DET 3/WF, SUPV 1, or Manual Release)

Note: SUPV 1 will only be active if it’s part of the activation condition.

• Agent Pre-Release Condition

• Agent Release Condition

• Manual Release Input

•Waterflow Input

•Abort Input

•Supervisory Input

• Any Alarm: (DET 1, DET 2, DET 3/WF, or Manual Release)

1-4.4.3.2 Trouble Relay

The trouble relay is "normally energized” with AC Power ON and will de-energize upon receipt
of a trouble condition. This change is non-latching and the relay will revert to its normal state
upon removal of the trouble state. For Central Station operation, especially with an intermittent
AC power supply, it may be desirable to delay the change of state of the trouble relay in case
of AC power failure. See Chapter 3, Configuration to enable this configuration.

1-4.4.4 Auxiliary Power Output

The AEGIS provides one auxiliary power output rated 1 Amp at 24 Vdc (Nominal) and is
intended to be used with 4-wire devices such as Flame Detectors, Smoke Detectors, etc. All
applicable compatible devices contained in this manual may be used. For FM installations, use
FM Approved Flame Detectors.

Note: Operation of the System Reset control switch will interrupt the Auxiliary Power Output

for a period of time not exceeding five (5) seconds.

August 2007 1-10 P/N 06-236716-001

Installation

INSTALLATION

2-1 INSTALLATION MATERIALS

2-1.1 Materials Provided

Check and ensure that the received shipment of the Kidde AEGIS™ unit consists of:

Table 2-1. Kidde AEGIS Control Unit Contents

Description Part Number Quantity

Enclosure Assembly (with door) 06-220132-001 1
Power Supply Unit 06-118394-001 1
Printed Circuit Board (PCB) 06-220113-001 1
Bezel Assembly 06-220114-001 1
Hardware Kit 06-220147-001 1
Installation/Configuration Kit 06-220148-002 1

CHAPTER 2

Operating Instructions 06-236719-002 1
Keys (in poly bag) 06-250319-013 1

The Hardware Kit contains the following:

Table 2-2. Hardware Kit Contents (P/N 06-220147-001)

Description Quantity

Ground Wire Assembly (Power Supply Unit Enclosure) 1
Power Supply Unit Wiring Harness 1
Battery Harness (2 long jumpers, 1 in-line fuse holder) 1
AC Safety Cover/Warning Label 1
3/4-inch Nylon Spacer 1
Nylon Pan Head Screw (8-32 x 1-1/4) 1
Threaded Aluminum Standoff (8-32 x 2-3/8) 8
INT Sems Screw (8-32 x 5/16) 8
Power Supply Unit Rentention Screw (M3 x 5) 1
End of Line Resistor Assembly (5.1K) 10
1/4-inch x 1-1/4-inch 10A Time Delay Fuse

Cooper Bussman MDA-10-R

2-1.2 Materials Required

The materials listed below are not supplied with the system, but are required for installation.

• No. 10 or 3/16-inch mounting hardware

P/N 06-236716-001 2-1 August 2007

1

Installation

• Electrical wiring and conduit

• 4-inch electrical junction boxes (as required)

• Wire-nuts and crimp-on terminals (as required)

• Ground strap (for use when handling printed circuit boards)

2-2 INSTALLATION GUIDELINES

2-2.1 Electrical Connections

Take special care when installing the system and follow the guidelines given in the following
paragraphs.

Install electrical conduit and wiring in accordance with applicable National Electrical Code,
NFPA Standard and state and local building code requirements.

The incoming AC voltage must be stable and within the permissible voltage range. This is
especially important in new construction where incoming power may be high or unstable, and
temporary connections may cause large inductive voltage spikes.

Most supervised circuits use voltage or current sensing circuits that are sensitive to induced
voltages on the sensor wiring.

Do not under any circumstances run AC power, speaker, PA, intercom or switch

CAUTION

2-2.2 Grounding and Lightning Protection

CAUTION

control wiring with inductive loads in the same conduit or in the immediate vicinity
of sensor wiring. Control unit damage or malfunction may result.

The system should never be connected to a conduit or green wire circuit that is also
used to power resistance heating, motors, fans, air-conditioning equipment or
fluorescent lighting circuits. Leakage currents from these types of circuits into the
ground return could damage sensitive system components.

A separate earth ground or cold water pipe with properly bypassed water meter
should be used. All external devices such as horns or alarm bells should have their
housings grounded. All low-level signal cables should have foil shielding and a
drain wire to be installed in their own grounded metallic conduit.

Ground only one end of the drain wire or shield, since a ground on both ends will
provide a current path and thus subject the circuit to induced RF currents and
noise. A minimum alternative would be to use shielded #16 AWG twisted pair wire.

Adequate lightning protection must be provided for the incoming power at the
building entry. Arrestor circuitry and earth grounding should be in accordance with
article 250 of the National Electric Code.

There is no known protective device available that is capable of protecting
equipment from damage caused by a direct lightning hit due to the extremely high
energy released (10 million to 100 million volts at 10,000 to 30,000 or more
amperes). However, line surges from indirect strikes and voltage spikes induced
through power line load switching can be minimized by the addition of transient
suppressors.

Although the Kidde AEGIS circuits have transient protection devices, additional
protection is required in areas subject to above average lightning activity or
induced voltage spikes and fluctuations due to power line load switching.

August 2007 2-2 P/N 06-236716-001

2-2.3 Terminating Wiring Conductors

For all subassemblies, strip 1/2-inch (13 mm) and leave straight for insertion beneath head of
screw on one side only (do not loop conductor around screw). If using stranded conductor,
twist and tin or use terminal lug.

2-2.4 Maxim um Wiring Length

Table 2-3 lists wiring gauge recommendations, resistance, and maximum length.
Refer to Appendix C for maximum allowable wire resistance for alarm signaling and initiating

circuits.

Table 2-3. Wiring Gauge Recommendation, Resistance, and Maximum Lengths

Wire Gauge Resistance/1000 ft. (305 m)

12 AWG 1.588 ohms
14 AWG 2.525 ohms
16 AWG 4.016 ohms
18 AWG 6.385 ohms

Installation

2-2.5 DC Load Distribution

Operating power for all initiating and indicating circuits is provided by the power supply. 4-wire
24 Vdc smoke detectors and other listed, compatible external 24 Vdc loads may be powered
from the power auxiliary output. DC load calculations must be performed to determine if the
power supply is capable of providing the total system current demand. The calculations will
also determine the minimum standby battery capacity in accordance with applicable NFPA
codes. Refer to Appendix A for Battery Capacity Calculations.

2-2.6 Enclosure Location

Care should be taken in planning the enclosure location. The enclosure is intended only for
indoor use in a location free from rain, condensation, excessive dust, moisture or other
airborne contamination. The enclosure must not be exposed to ambient conditions outside
those specified in Appendix C.

Installation on firewalls is generally not recommended. However, in situations
with no suitable alternative locations, ensure acceptance by the local AHJ before

CAUTION

installation.

Position the enclosure in a readily accessible and easily visible location. Ensure there is
1-1/2 ft. (457 mm) clearance or more in front and to the door hinge side of the enclosure for
the door to swing open completely.

The type of hardware is at the discretion of the installer, but must be in accordance with good
electrical and safety practices.

P/N 06-236716-001 2-3 August 2007

Installation

2-3 INSTALLATION PROCEDURE

2-3.1 Mounting the Enclosure Assembly, P/N 06-220132-001

The control unit is designed to be surface or semi-flush mounted. Use screws or bolts no
smaller than No. 10 (3/16-inch or 5 mm) in diameter to secure the enclosure to wall studs or
masonry walls. Never mount the enclosure to drywall or plaster walls without securing to studs.

Locate the middle of the enclosure approximately 66-inches (1676 mm) above the floor so the
control unit display is positioned at a convenient height for the operator. Refer to Figure 2-1.
Figure 2-2 shows the control unit enclosure dimensions.

19 in.

(483 mm)

66 in.

(1676 mm)

MAX.

FLOOR

Figure 2-1. Installation Height Above Floor

Perform the following steps prior to installing the enclosure:

1. Disconnect the ground wire that connects the enclosure door to the back box.

2. Remove the control unit front door by rotating the door approximately 90° from its closed
position. Lift up the door to allow the door’s hinge pins to clear the mating-hinge sockets
on the back box.

3. Remove the separately packaged power supply, printed-circuit board, and installation kit,
and set them and the front door aside in a safe location to prevent damage.

August 2007 2-4 P/N 06-236716-001

7/16 in.

(11 mm)

TYP 2 PLACES

GROUND

9/32 in.
(7 mm)

1/2 in.

(13 mm)

1 in.

(25 mm)

STUD

17 in.

(432 mm)

1-1/8 in.
(29 mm)

(127 mm)

5 in.

12-1/4 in.
(311 mm)

5-1/8 in.

(130 mm)

9-1/8 in.
(232 mm)

14-1/4 in.
(362 mm)

13-1/8 in.
(333 mm)

TOP VIEW

1 in.

(25 mm)

18-13/16 in.

(978 mm)

1-1/2 in.
(38 mm)

Installation

1-1/2 in. (38 mm) KNOCKOUTS

4ONTOP
3 ON EACH SIDE
1 ON BOTTOM

2-1/2 in.
(64 mm)

2 in.

(57 mm)

5 in.

(127 mm)

8 in.

(203 mm)

GROUND

STUD

Figure 2-2. Control Unit and Surface Mounting Dimensions

2-3.1.1 SURFACE MOUNTING

1. Mark and pre-drill holes for four mounting bolts using the dimensions shown in Fig ure 2-2.
The installer must supply the mounting bolts (No. 10 or 3/16-inch (5mm)). There are two
holes and two keyhole slots in the backbox that serve as a template for surface mounting.
The type of hardware to be used is at the discretion of the installer, but must be installed
in accordance with NFPA 70 (NEC).

2. Insert the upper two fasteners in the wall. Leave approximately 1/4-inch (6 mm)
protruding for both screws.

3. Slip upper keyholes of the back box over the two protruding screws. Tighten the screws.

4. Insert and tighten the two lower screws.

5. Attach wiring conduit to the enclosure via the enclosure knockouts, and pull the required
number of wires through the conduit to the enclosure. Leave approximately 2 to 3 feet (600
to 900 mm) of wire length in the enclosure for future internal connections.

14-3/16 in.
(360 mm)

FRONT VIEW

9/32 in. DIAMETER
HOLES TYP (2)
PLACES

5 in.

(127 mm)

SIDE VIEW

19 in.

(483 mm)

P/N 06-236716-001 2-5 August 2007

Installation

2-3.1.2 SEMI-FLUSH MOUNTING

1. Cut and plumb an opening of dimensions as shown in Figure 2-3 in the wall on which the
control unit will be semi-flush mounted.

5 in.

(127 mm)

14-1/4 in.
(362 mm)

TOP VIEW

WALL CUTOUT

14-3/8 in.
(365 mm)

FRONT VIEW

18-13/16 in.

(978 mm)

19-1/8 in.
(486 mm)

5 in.

(127 mm)

SIDE VIEW

Figure 2-3. Semi-Flush Mounting Dimensions

2. Position and plumb the back box in the opening made in Step 1. Ensure that the front edge
of the back box is at least 3/4-inch (19 mm) from the surface of the wall. Secure the back
box to the wall with appropriate mounting bolts (up to 1/4-20).

3. Attach wiring conduit to the enclosure through the enclosure knockouts, and pull the
required number of wires through the conduit to the enclosure. Leave approximately 2 to
3 feet (600 to 900 mm) of wire length in the enclosure for future internal connections.

2-3.1.3 SEMI-FLUSH MOUNTING WITH TRIM RING, P/N 76-600000-007

A Trim Ring (P/N 76-600000-007) can be used to enhance the final installed appearance of a
semi-flush mounted AEGIS unit.

1-1/2 in.
(38 mm) TYP.
ALL AROUND

14-9/16 in.

(370 mm)

INSIDE

23-13/16 in.

(605 mm)

20-13/16 in.

(529 mm)

INSIDE

17-9/16 in.

(446 mm)

Figure 2-4. Trim Ring Dimensions

August 2007 2-6 P/N 06-236716-001

Installation

1. Ensure that the enclosure is semi-flush mounted as directed in Paragraph 2-3.1.2.

2. Prepare the surface of the wall for trim-ring installation by clearing all dirt and debris within
1-1/2 inches (38 mm) of the back-box perimeter. Ensure that this perimeter area is clean
and dry.

3. Install the trim ring by first removing the protective strips that cover the adhesive tap e on
its back surface. Slip the trim ring over the back box with the adhesive-tape side toward
the wall. The trim ring has tabs on both sides that aid in aligning it with the back box. Pres s
all sides of the trim ring to the wall when it is correctly aligned and plumb with the back
box.

1-3/4 in.
(44 mm)

MIN.

WALL

TRIM RING

BACK BOX

COVER

Figure 2-5. Trim Ring Installed

2-3.2 Installing the Power Supply Unit, P/N 06-118394-001

Use a ground strap to prevent static discharge that could damage the power

CAUTION

supply.

1. Make sure the control unit location is dry and that the enclosure is free of construction dust
and metal shavings prior to installing the power supply.

2. Remove the power supply unit from its shipping carton.

3. The AEGIS unit is supplied with one of two equivalent power supplies. Compare the
terminal block wiring legend on the provided power supply with the diagrams in Figure 2-6
and connect the wiring harness as shown.

4. Connect the Power Supply Wiring Harness (P/N 06-220025-001) to the power supply unit.
Next connect the fork end of the green ground wire (P/N 06-129928-002) to the
earth-ground terminal of the power supply unit. Refer to Figure 2-6 and Figure 2-7 for wire
harness and earth-ground connections.

P/N 06-236716-001 2-7 August 2007

Installation

TO PSU J2

CONNECTOR ON

PCB

TO PSU J2

CONNECTOR ON

PCB

GND

NEUTRAL

WHT/BLK

WHT

BLK

RED

GRN

LINE

-24V

+24V

GROUND WIRE FROM INSTALLATION KIT

CONNECT TO LOWER EARTH-GROUND STUD
ON LEFT-HAND SIDE OF ENCLOSURE

OR

GND

NEUTRAL

LINE

WHT/BLK

WHT

BLK

RED

GRN

-V

-V

+V

+V

GROUND WIRE FROM INSTALLATION KIT

CONNECT TO LOWER EARTH-GROUND STUD
ON LEFT-HAND SIDE OF ENCLOSURE

ATTENTION!

THE CONTROL UNIT IS SUPPLIED WITH ONE OF TWO EQUIVALENT

POWER SUPPLIES. COMPARE THE TERMINAL BLOCK WIRING LEGEND

ON THE PROVIDED POWER SUPPLY WITH THE DIAGRAMS AND

CONNECT THE WIRING HARNESS AS SHOWN IN THE APPLICABLE DIAGRAM.

Figure 2-6. Power Supply Unit Wiring

August 2007 2-8 P/N 06-236716-001

230 V

115 V

THREADED HOLE FOR

3 x 10 mm MOUNTING

SCREW

FASTENING TAB
FOR SCREW

RETENTION

TABS

TYP (2)

GROUND WIRE ATTACHED

TO GROUND STUD

Installation

Figure 2-7. Power Supply Unit Installation

5. Thread the supplied 3 x 10 mounting screw part way into the lower of the two threaded
holes of the power supply unit. See Figure 2-7.

6. Set the power supply unit AC-input-voltage selector switch to either 115 Vac or 230 Vac.
Use the 115 Vac position for 110-120 Vac supplies and 230 V position for 230-240 Vac
supplies. See Figure 2-7.

7. Locate the two power supply unit retention tabs and the fastening tab in the
enclosure’s back panel.

8. Position the power supply unit with the wire harness down, and then slide it onto the retention
tabs. The 3 x 10 mm mounting screw should slide into the slot of the fastening tab at the same
time.

9. Tighten the screw onto the fastening tab.

10.Connect the ring end of the power supply’s green ground wire (P/N 06-129928-002) to the
earth-ground stud on the lower left side of the backbox wall. See Figure 2-6 and
Figure 2-7.

2-3.3 Installing the Printed Circuit Board (PCB), P/N 06-220113-001

Use a ground strap to prevent static discharge that could damage sensitive

CAUTION

components on the Printed Control Board.

1. Make sure the control unit location is dry and that the enclosure is free of construction dust
and metal shavings prior to installing the PCB.

P/N 06-236716-001 2-9 August 2007

Installation

AC PROTECTIVE COVER
(WITH STANDOFF)

Figure 2-8. PCB Installation

2. Securely screw one each of the eight (8) 2-3/8 inch (60 mm) aluminum standoffs
(P/N 06-118533-001) onto each of the eight (8) threaded PEMs on enclosure backbox (top
three rows) as shown in Figure 2-8.

Note: Do not use the bottom row of threaded PEMs.

3. Slip on a wrist ground strap and clip the ground strap to the earth ground in the enclosure.
Do not remove the PCB from its shipping carton unless you have established a common
earth-ground potential among yourself, the enclosure, and the PCB shipping carton.

4. Remove the PCB from its shipping carton and position each of its eight (8) mounting holes
over one of the aluminum standoffs so that the AC-input terminal block is in the lower-left
corner.

5. Secure the PCB to the standoffs using the seven (7) 8-32 x 5/16 (8 mm) (P/N 06-250354 -

082). Do not tighten the screws at this time.
The PCB mounting hole in the lower left corner utilizes a longer nylon screw that also holds

the AC Safety Cover in place. See Paragraph 2-3.4.1.

6. Place the free end of the longer of the two factory-installed Earth-Ground wires under the
screw assembly of the PCB (marked detail A in Figure 2-9). Tighten the remaining eight
screws. Be careful not to over-tighten.

7. Plug the harness from the power-supply unit into Connector J2 in the lower-left-hand
corner of the PCB.

August 2007 2-10 P/N 06-236716-001

Installation

Figure 2-9. PCB-to-Cabinet Grounding Diagram

2-3.4 AC Input and Battery Backup Connections

TB6

TB7

TB8

TB9

TB10

TB11

TB12

TB5

A

AC SUPPLY SELECT SWITCH (S6)

TB13

TB14

EARTH-GROUND TERMINAL FOR
POWER SUPPLY AND GREEN
WIRE OF AC SUPPLY

TB16TB15

TB2

TB3TB4

TB1

TB19

TB17

TB18

The control unit uses AC power (by others) as the primary power source, together with a 24 Vdc
standby battery.

Use caution when connecting AC power to the control unit. High-voltage and
AC-powered circuits are present in the control unit. Be sure to take suitable

WARNING

precautions and to adequately ground the control unit to reduce the risk of
electrical shock.

2-3.4.1 CONNECTING AC POWER

AC power must be provided to the control unit using a 3-conductor 14 AWG cable. The AC
power cable shall be run through a one-inch conduit from a dedicated, 15-ampere circuit
breaker. The conduit must be attached to the left side of the enclosure through one of the
upper left corner knockouts.

Perform the following steps to connect AC power to the control unit.

1. Ensure the circuit breaker at the dedicated AC power source is in the OFF position.

2. To ensure correct AC supply supervision, for 110-120 Vac operation, move the AC Supply
Select Switch (S6) on the PCB to the 120 position. For 220-240 Vac operation, move it to
the 240 position.

3. Attach the 3-conductor AC power cable to TB13 on the PCB.

P/N 06-236716-001 2-11 August 2007

Installation

C

POWER CONNECTIONS
FROM AC SUPPLY

PROTECTIVE COVER
FOR AC POWER INPUT

ENCLOSURE WALL

WHITE (NEUTRAL)

BLACK (LINE/HOT)

GREEN (GREEN)

SUPERVISED

4. To install the Protective Cover for AC Power input, fold along scored lines as shown in
Figure 2-10.

5. Insert spacer and align thru holes and spacer with PCB standoff in lower left corner.

6. Attach to PCB with nylon screw.

TB13

TO PSU
EARTH GND

AC POWER SELECTION SLIDE SWIT
DOWN FOR 120 Vac / UP FOR 220-240

STANDOFF FOR AC PROTECTIVE COVER

Figure 2-10. Primary Power Connections

LOWER LEFT CORNER OF
PRINTED CONTROL BOARD

August 2007 2-12 P/N 06-236716-001

2-3.5 Installing Backup Batteries

Perform the following steps to install the backup batteries

1. Using Appendix A, Battery Capacity Calculations, calculate the size of the battery required
for the application.

2. Ensure that the batteries are being placed into service within three (3) months of the ship
date if stored at about 75°F (24°C) or within one (1) month if stored at 100°F (38°C). For
longer storage time, they require charging per manufacturer’s specification to prevent
permanent loss of capacity.

3. Observing polarity, connect the two (2) or four (4) 12-volt series-wired batteries of the
required ampere hour (AH) capacity to TB12 (Batt Out) using battery cable
(P/N 06-129925-002). Refer to Figure 2-11.

BATTERY HARNESS (P/N 06-129925-002)

Installation

TB12

BATT OUT

12 V

BATTERY

BATTERY HARNESS (P/N 06-129925-002)

BATTERY

12 V

BATTERY

BATTERY HARNESS (P/N 06-129925-002)

12 V

BATTERY

BATTERY

12 V

BATTERY

12 V

TB12

BATT OUT

12 V

ADDITIONAL BATTERY
CABLES TYP (BY INSTALLER)

NOTE:

LOCATE ALL BATTERIES IN A COMMON BATTERY
CABINET, OR IN CLOSE-COUPLED BATTERY CABINETS
WITH ALL BATTERY CABLES IN A CONDUIT.

P/N 06-236716-001 2-13 August 2007

Figure 2-11. Backup Battery Connections

Installation

2-4 TERMINATIONS AND WIRING DIAGRAMS

2-4.1 Terminal Blocks

The PCB provides the following input and output terminations as shown in Figure 2-12.

• Detector 1 (TB1) • Trouble Relay (TB8) • Agent Release ARC 2 (TB15)

• Detector 2 (TB2) • Programmable Relay 3 (TB9) • Aux 24 Vdc Output (TB16)

• Waterflow/Detector 3 (TB3) • Programmable Relay 2 (TB10) • Notification Appliance Circuit 3 (TB17)

• Manual Release (TB4) • Programmable Relay 1 (TB11) • Notification Appliance Circuit 2 (TB18)

• Abort (TB5) • Battery Out (TB12) • Notification Appliance Circuit 1 (TB19)

• Supervisory 1 (TB6) • AC IN (TB13) • PSU (J2)

• Supervisory 2 (TB7) • Agent Release ARC 1 (TB14) • RS-232 Communications Port

TROUBLE RELAY

PROGRAMMABLE RELAY 3

PROGRAMMABLE RELAY 2

PROGRAMMABLE RELAY 1

BATT OUT

SUPERVISORY

TB7

TB8

TB9

TB10

TB11

TB12

AC SUPPLY SELECT SWITCH (S6)

2

SUPERVISORY
1

TB6

ABORT

MANUAL

RELEASE

TB5

WATERFLOW/
DETECTOR 3

TB3TB4

DETECTOR 2

TB2

TB1

TB19

DETECTOR 1

NAC 1

AC IN

TB13

TB14

RELEASE

ARC 1

RELEASE

ARC 2

TB16TB15

AUX

24 VDC

TB17

NAC 3

TB18

Figure 2-12. Printed Circuit Board

August 2007 2-14 P/N 06-236716-001

NAC 2

2-4.2 Input Circuit Wiring (TB1 through TB7)

Refer to Appendix B for a list of compatible listed smoke/electronic heat detectors.

Installation

2+

1+

TB1, TB2, TB3

2-

1-

7

6

3

2

1

EOL RESISTOR

5.1K, 0.5 W

P/N 06-129025-002

7

6

3

2

1

Figure 2-13A. Class B, Style B Wiring for Smoke/Electronic Heat Detectors

7

6

3

2

1

7

6

3

2

1

1+

TB1, TB2, TB3

Figure 2-13 B. Class A, Style D Wiring for Smoke/Electronic Heat Detectors

P/N 06-236716-001 2-15 August 2007

2+

2-

1-

EOL RESISTOR

5.1K, 0.5 W
P/N 06-129025-002

Installation

2+

1+

TB1, TB2, TB3, TB4,
TB5, TB6, OR TB7

2-

1-

EOL RESISTOR

5.1K, 0.5 W

P/N 06-129025-002

Figure 2-13C. Class B, Style B Wiring for Contact Devices

2-

1+

2+

1-

EOL RESISTOR

5.1K, 0.5 W

TB1, TB2, TB3, TB4,
TB5, TB6, OR TB7

P/N 06-129025-002

Figure 2-13D. Class A, Style D Wiring for Contact Devices

LEGEND

SUPERVISED POWER LIMITED

Figure 2-13. Initiating Device Circuit Wiring

August 2007 2-16 P/N 06-236716-001

2-4.3 Notification Appliance Circuit Wiring (TB17, TB18, TB19)

Installation

2+

1+

TB17, TB18, TB19

2-

+

-

EOL RESISTOR

5.1K, 0.5 W

P/N 06-129025-002

+

-

1-

Figure 2-14 A. Class B , Style Y Notification Appliance Circuit

+

+

2+

1+

TB17, TB18, TB19

Note: 1. Regulated 24 Vdc, 28 Vdc maximum.

2. Suitable for synchronized and non-synchronized notification appliances.

3. Use polarized notification appliances only.

4. Maximum single notification appliance current is 1.5A.

5. Voltage drop: 2.0 V (maximum)

1-

2-

Figure 2-14B. Class B, Style Y Notification Appliance Circuit Wiring

EOL RESISTOR

5.1K, 0.5 W
P/N 06-129025-002

LEGEND

SUPERVISED POWER LIMITED

-

-

Figure 2-14. Notification Appliance Circuit Wiring

P/N 06-236716-001 2-17 August 2007

Installation

2-4.4 Agent Releasing Circuit Wiring

Refer to Appendix B for a list of compatible listed releasing devices.

TB14 OR TB15

R1+

R2+

R1-

R2-

RED

BLK

SOLENOID

P/N 06-220023-001
IN-LINE RELEASING DEVICE - MUST
BE INSTALLED CLOSE NIPPLED TO
SOLENOID ENCLOSURES

Figure 2-15A. Agent Release Circuit - Single Solenoid, Power-Limited

TB14 OR TB15

R1+

R2+

R1-

R2-

SOLENOID

Figure 2-15B. Agent Release Circuit - Single Solenoid, Non-Power-Limited

August 2007 2-18 P/N 06-236716-001

TB14 OR TB15

R1+

R2+

R1-

Installation

R2-

BLK

RED

SOLENOID

BLK

RED

IN-LINE RELEASING DEVICES

P/N 06-220023-001

MUST BE INSTALLED CLOSE

NIPPLED TO SOLENOID ENCLOSURES

Figure 2-15C. Agent Release Circuit — Dual Solenoid, Power-Limited

TB14 OR TB15

R1+

R2+

R1-

R2-

SOLENOID

Figure 2-15D. Agent Release Circuit — Dual Solenoid, Non-Power-Limited

P/N 06-236716-001 2-19 August 2007

Installation

TB14 OR TB15

R1+

R2+

R1-

R2-

SOLENOID P/N 83-100034-001

BLACK

WHITE

MICROSWITCH P/N 87-120039-001

NOTE
TO MAKE THIS A POWER LIMITED CIRCUIT, ADD IN-LINE RELEASING
DEVICES (P/N 06-220023-001) AS SHOWN IN FIGURE 2-15C.

N.C.

N.O.

Figure 2-15E. Agent Release Circuit for XV and CXV Control Heads

TB14 OR TB15

R1+

R2+

R1-

R2-

10 OHM LIMITING

RESISTOR

INITIATOR

MAXIMUM WIRE RESISTANCE: 3 OHMS

MAXIMUM CURRENT UNDER
FAULT CONDITIONS: 5A

Figure 2-15F. Agent Release Circuit - Initiators, Non-Power-Limited

Note: 1. Polarities must be observed for solenoids P/N 890181 and 48650001.

2. The inline releasing device P/N 06-220023-001 must be close nippled
to Solenoid enclosures.

3. The ARC is Non-Power-Limited when in-line device is not used.

4. Route Non-Powered-Limited wiring at least 1/4-inch away from all Power-Limited
wiring. See Appendix F. Do not attach Power-Limited wiring to the same
terminal block.

5. When firing initiators, the limiting resistor must have a rating of 1 watt minimum.

6. Control Head P/N 90-487100-001 when used with the control unit must
include Solenoid P/N 83-100034-001 and Microswitch P/N 87-120039-001.

Figure 2-15. Agent Release Circuit Wiring

August 2007 2-20 P/N 06-236716-001

2-5 INSTALLING THE BEZEL, P/N 06-220114-001

1. Align bezel cutouts to the timer and control switches on the PCB.

2. Gently press the bezel onto PCB so snap-on clips click into the PCB fitted holes.

2-6 INSTALLING OPTIONAL DEAD-FRONT PANEL, P/N 06-220175-001

Certain applications such as those in Canada require a dead-front panel as described in
Paragraph 1-4.1.2. Install as follows:

1. The tab on the dead-front panel goes over the bottom enclosure lip (Figure 2-16).

2. Attach to control unit with supplied screws.

MOUNTING SCREWS

DEAD-FRONT
PANEL (SIDE VIEW)

THIS SIDE AGAINST
BEZEL ASSEMBLY

Installation

DEAD-FRONT

PANEL

Figure 2-16. Dead-Front Panel Installation

2-7 INSTALLING THE ENCLOSURE DOOR (STANDARD DOOR)

1. Slide the door to allow the door’s hinge pins to align with the mating-hin ge sockets in the
back box.

2. Connect the ground wire that connects the enclosure door to the back box.

2-8 INSTALLING THE ENCLOSURE DOOR (DOOR WITH SWITCHES)

1. Slide the door to allow the door’s hinge pins to align with the mating-hin ge sockets in the
back box.

2. Connect the ground wire that connects the enclosure door to the back box.

TAB GOES OVER
ENCLOSURE BOTTOM
LIP

2-8.1 Installing Manual Release and Abort Switches, P/N 06-220169-001

1. Install locking nut on the toggle switch.

2. Install toggle switch from back of enclosure door. Make sure the ON position of the toggle
switch is facing the front of the the enclosure door and is in the up position.

3. Attach switch guard, lock washer, and locking ring and tighten.

P/N 06-236716-001 2-21 August 2007

Installation

Note: Switch guard is keyed and can only be installed one way.

4. Install locking nut on the abort switch.

5. Install abort switch from back of enclosure door. Attach pushbutton switch guard and
tighten.

SWITCH

GUARD

INTERNAL

TOOTH

LOCKWASHER

PUSHBUTTON

SWITCH

GUARD

LOCKING
NUT

LOCKING
NUT

SIDE VIEW

MANUAL RELEASE

ABORT

FRONT VIEW

MANUAL
RELEASE
SWITCH

ABORT
SWITCH

AND LOCKING RING

Figure 2-17. Installation of Manual Release and Abort Switches

6. Attach black wires from switch wire harness to the right side of the toggle switch as shown
in Figure 2-18.

7. Route switch wire harness as shown in Figure 2-18.

8. Install cable clamps and 8-32 kep nuts to secure switch wire harness to enclosure door.

9. Run the black wires from the Manual Release switch to TB4 on the PCB. Refer to
Figure 2-13 through Figure 2-15 for wiring configurations.

10. Run the white wires from the Abort switch to TB5 on the PCB. Refer to Figure 2-13 through
Figure 2-15 for wiring configurations.

Power-limited wiring from the front cover Manual Release and Abort switches
to their respective terminal blocks on the PCB must be routed to maintain a

CAUTION

1/4-inch distance from non-power-limited wiring. Refer to Appendix F for more
details.

August 2007 2-22 P/N 06-236716-001

BLACK WIRES
FROM SWITCH

WIRE HARNESS

Installation

- WHITE WIRES
TO TB5

- BLACK WIRES
TO TB4

MANUAL

RELEASE

SWITCH

ABORT

SWITCH

REAR VIEW

Figure 2-18. Installing Switch Harness Assembly

2-9 COMPLETING THE INSTALLATION

1. Power-up the system AC first and then DC.

2. Configure as described in Chapter 3.

3. Once configured, test the complete system for operation. Once operation is verified, the
installation is complete.

CABLE CLAMP
AND 8-32 KEP NUT
(SUPPLIED)
(TYP 3 PLACES)

SWITCH WIRE
HARNESS

P/N 06-236716-001 2-23 August 2007

Installation

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 2-24 P/N 06-236716-001

Configuration

CHAPTER 3

CONFIGURATION

3-1 ENTERING SITE - SPECIFIC CONFIGURATION

The Kidde AEGIS™ is suitable for a wide variety of applications by means of configuring its
inputs and outputs. Inputs and outputs are configured via the operator interface. The following
sections details on how to enter or change configuration settings.

POSITION

23

1

COUNTDOWN TIMER (SECS)

Figure 3-1. Digital Display

3-1.1 Entering the Password

To enter the configuration setting mode, you must enter the factory default password (186)
via the operator interface. Ensure that no alarms or supervisories are present and perform the
following.

Step Description Display

1Press and hold the Acknowledge control switch and within five (5) seconds,

press the System Reset control switch.

2Press Output Disable to advance (each press advances one digit).

3 When correct, press the Acknowledge control switch. Position 1 is accepted

and cursor moves to position 2.

4Press Output Disable to advance (each press advances one digit).

5 When correct, press the Acknowledge control switch. Position 2 is accepted

and cursor moves to position 3.

6Press Output Disable to advance (each press advances one digit).

7 When correct, press the Acknowledge control switch. Position 3 is accepted

and if the password is is correct, the display shows ‘00’ and the AEGIS enters
the configuration mode.

The control unit exits the configuration mode upon status change, or if more than five (5)
minutes have expired since the last control switch press. Only saved changes are retained by
the control unit.

P/N 06-236716-001 3-1 August 2007

Configuration

3-1.2 Lost, Forgotten or Incorrect Passwords

In the event that the entered password is incorrect, the display reads "Err" for three (3)
seconds and then prompts for entering the password again b y displaying "0" as the first digit.

When at the "Err" display, press the Signal Silence control switch to display a random 3 digit
code. Make a note of the code and call Technical Support. The control unit does not timeout
(exit out of the configuration mode) when the display reads the random 3-digit code.

Note: Do not press any buttons while this 3 digit code is being displayed.
Technical Support will translate this 3 digit code to a new password that will work only on a

control unit displaying the original random code for one time only. When given the Temporary
Password (the 3 digit code should still be displayed), press the Signal-Silence control switch.
The display is now exactly as it would be to enter a password:

Enter the Temporary Password in the same manner as entering a regular Password.
When the password has been accepted (and the first configuration item is being displayed

"00x", where x is the left most digit of the Temporary Password), you should:

1. either press the Signal Silence control switch in order to accept and save the current
Temporary Password as a Permanent Password; OR

2. enter the desired Password in configuration items 0, 1, and 2, and then press the Signal
Silence control switch in order to accept and save it.

August 2007 3-2 P/N 06-236716-001

3-2 CONFIGURATION SETTINGS

This section describes the configuration settings for the AEGIS unit. Use Table 3-1 to set the
configuration settings.

• To advance to the next selection for an item, press the Output Disable control switch.

• To advance to the next item, press the Acknowledge control switch.

• To accept a configuration setting change and exit the Configuration menu at any step in
the process, press the Signal Silence control switch. Check the configuration by starting
the configuration process again, checking all items, and exiting by pressing System Reset
after inspecting the last item.

• To exit the configuration menu at any time, press the System Reset control switch. This
reverts the control unit to its previous state.

Note: The control unit takes about five (5) seconds to boot up after exiting the configuration

menu.

POSITION

23

1

COUNTDOWN TIMER (SECS)

Configuration

Configuration

Number

(Position 1, 2)

00 1st Password Character 0 — 9 1
01 2nd Password Character 0 — 9 8
02 3rd Password Character 0 — 9 6
03 Application Mode -

Table 3-1. Configuration Settings

Configuration Item Configuration (Position 3) Selection

Release Circuit 1

1 — Release Circuit 1 not in use
2 — Manual Release or Single Zone input from DET 1
3 — Manual Release or Single Zone input from DET 2
4 — Manual Release or Single Zone input from any one of

DET 1 or DET 2
5 — Manual Release or Cross Zone input from DET 1 and

DET 2
6 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2, and DET 3/WF
7 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2, and SUPV 1
8 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2, DET 3/WF, and SUPV 1 (except
DET 3/WF and SUP 1)

1

Default

Mode

6

P/N 06-236716-001 3-3 August 2007

9 — Manual Release or Cross Zone input from SUPV 1 and
either DET 1 or DET2

Configuration

Table 3-1. Configuration Settings

Configuration

Number

(Position 1, 2)

04 Application Mode -

05 Abort Both or Release

06 Abort 1 — Mode 1 (UL)

Configuration Item Configuration (Position 3) Selection

1 — Release Circuit 2 not in use (see note 1)

Release Circuit 2

2 — Manual Release or Single Zone input from DET 1
3 — Manual Release or Single Zone input from DET 2
4 — Manual Release or Single Zone input from any one of

DET 1 or DET 2
5 — Manual Release or Cross Zone input from DET 1 and

DET 2
6 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2 and DET 3/WF
7 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2, and SUPV 1
8 — Manual Release or Cross Zone input from any two of

the following: DET 1, DET 2, DET 3/WF, and SUPV 1 (except
DET 3/WF and SUP 1)

9 — Manual Release or Cross Zone input from SUPV 1 and
either DET 1 or DET2

1 — Activation aborts ARC 1 and ARC 2

Circuit 1

2 — Activation aborts ARC 1 only

Default

Mode

6

1

1
2 — Mode 2, (Reset)
3 — Mode 3 (IRI)
4 — Mode 4 (NYC)
5 — Mode 0 (Disable the Abort)

07 Input Circuit 3 1 — Detector (DET 3)

2 — Waterflow with Non-Silenceable NACs (DET WF)
3 — Waterflow with Silenceable NACs (DET WF)

08 Programmable Relay 1 1 — General alarm (DET 1, DET 2, DET 3/WF, or Manual

Release)
2 — First Alarm (DET 1, DET 2, DET 3/WF, or Manual

Release) (see note 2)
3 — First Alarm (DET 1, DET 2, DET 3/WF, Manual Release,

or SUPV 1) (see notes 2 & 3)
4 — Agent Pre-Release Condition
5 — Agent Release Condition
6 — Manual Release Input
7 — Waterflow Input
8 — Abort Input
9 — Supervisory Input

1

3

August 2007 3-4 P/N 06-236716-001

Table 3-1. Configuration Settings

Configuration

Configuration

Number

(Position 1, 2)

9 Programmable Relay 2 1 — General alarm (DET 1, DET 2, DET 3/WF, or Manual

10 Programmable Relay 3 1 — General alarm (DET 1, DET 2, DET 3/WF, or Manual

Configuration Item Configuration (Position 3) Selection

Release)
2 — First Alarm (DET 1, DET 2, DET 3/WF, or Manual

Release) (see note 2)
3 — First Alarm (DET 1, DET 2, DET 3/WF, Manual Release,

or SUPV 1) (see notes 2 & 3)
4 — Agent Pre-Release Condition
5 — Agent Release Condition
6 — Manual Release Input
7 — Waterflow Input
8 — Abort Input
9 — Supervisory Input

Release)
2 — First Alarm (DET 1, DET 2, DET 3/WF, or Manual

Release) (see note 2)
3 — First Alarm (DET 1, DET 2, DET 3/WF, Manual Release,

or SUPV 1) (see notes 2 & 3)
4 — Agent Pre-Release Condition

Default

Mode

4

5

5 — Agent Release Condition
6 — Manual Release Input
7 — Waterflow Input
8 — Abort Input
9 — Supervisory Input

11 Trouble Relay 1 — AC Failure response - Instantaneous

2 — AC Failure response - Delayed 1 minute
3 — AC Failure response - Delayed 60 minutes
4 — AC Failure response - Delayed 90 minutes
5 — AC Failure response - Delayed 120 minutes
6 — AC Failure response - Delayed 180 minutes

12 Manual Release Station

Time Delay - Release

Circuit 1

1 — Instantaneous (select for NYC)
2 — 10 seconds
3 — 20 seconds
4 — 30 seconds

13 Manual Release Station

Time Delay - Release

Circuit 2

1 — Instantaneous (select for NYC)
2 — 10 seconds
3 — 20 seconds
4 — 30 seconds

4

1

1

P/N 06-236716-001 3-5 August 2007

Configuration

Table 3-1. Configuration Settings

Configuration

Number

(Position 1, 2)

14 Automatic Time Delay -

15 Automatic Time Delay -

16 On-Time - R elease Circuit

Configuration Item Configuration (Position 3) Selection

1 — 0 seconds

Release Circu it 1

2 — 10 seconds
3 — 20 seconds
4 — 30 seconds (select for NYC)
5 — 40 seconds
6 — 50 seconds
7 — 60 seconds
1 — 0 seconds

Release Circuit 2

2 — 10 seconds
3 — 20 seconds
4 — 30 seconds (select for NYC)
5 — 40 seconds
6 — 50 seconds
7 — 60 seconds
1 — Agent Control Head 90 seconds

1 (see note 4)

2 — Deluge Solenoid 10 minutes

Default

Mode

7

7

1

3 — Deluge Solenoid 15 minutes
4 — Deluge Solenoid On Until Reset
5 — Initiators

17

Power Limited

- Release

Circuit 1 (see note 4)

1 — Power-Limited (one solenoid)
2 — Power-Limited (two solenoids)
3 — Non-Power-Limited (one solenoid)
4 — Non-Power-Limited (two solenoids)
5 — Initiators

18 On-Time - R elease Circuit

2 (see note 4)

1 — Agent Control Head 90 seconds
2 — Deluge Solenoid 10 minutes
3 — Deluge Solenoid 15 minutes
4 — Deluge Solenoid On Until Reset
5 — Initiators

19

-

Power Limited

Release

Circuit 2 (see note 4)

1 — Power-Limited (one solenoid)
2 — Power-Limited (two solenoids)
3 — Non-Power-Limited (one solenoid)
4 — Non-Power-Limited (two solenoids)
5 — Initiators

20 Trouble Latching 1 — Troubles are non-latching

2 — Troubles are latching (required for cUL)

3

1

3

1

August 2007 3-6 P/N 06-236716-001

Table 3-1. Configuration Settings

Configuration

Configuration

Number

(Position 1, 2)

21 Latching for

22 Latching for

23 Outputs Disabled by

24 NAC 1 relationship to

25 NAC 2 relationship to

Configuration Item Configuration (Position 3) Selection

1 — SUPV 1 is non-latching

Supervisory 1

2 — SUPV 1 is latching (forced if part of Cross-Zone)
1 — SUPV 2 is non-latching

Supervisory 2

2 — SUPV 2 is latching
1 — Disables ARCs

Isolate Button

2 — Disables ARCs and NACs
3 — Disables ARCs and Programmable Relays
4 — Disables ARCs, NACs and Programmable Relays
1 — ARC 1 only

ARCs

2 — ARC 2 only
3 — Both ARC 1 and ARC 2 (see note 5)
4 — Neither ARC 1 nor ARC 2 (see note 6)
5 — NAC 1 Not Used (see note 1)
1 — ARC 1 only

ARCs

2 — ARC 2 only
3 — Both ARC 1 and ARC 2 (see note 5)

Default

Mode

1

1

4

1

2

26 NAC 3 relationship to

ARCs

27 NAC 1 First Alarm

(see note 8)

4 — Neither ARC 1 nor ARC 2 (see note 6)
5 — NAC 2 Not Used (see note 1)
1 — ARC 3 only
2 — ARC 3 only
3 — Both ARC 1 and ARC 2 (see note 5)
4 — Neither ARC 1 nor ARC 2 (see note 6)
5 — NAC 3 Not Used (see note 1)
0 — 60 bpm Non-Silenceable
1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
8 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Only

Off)

3

1

P/N 06-236716-001 3-7 August 2007

C — NAC 1 Off (see note 7)

Configuration

Table 3-1. Configuration Settings

Configuration

Number

(Position 1, 2)

28 NAC 1 Pre-Release

29 NAC 1 Releasing

Configuration Item Configuration (Position 3) Selection

0 — 60 bpm Non-Silenceable

(see note 9)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 1 Off (see note 7)
0 — 60 bpm Non-Silenceable

(see note 10)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable

Default

Mode

3

5

3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 1 Off (see note 7)

August 2007 3-8 P/N 06-236716-001

Table 3-1. Configuration Settings

Configuration

Configuration

Number

(Position 1, 2)

30 NAC 2 First Alarm

31 NAC 2 Pre-Release

Configuration Item Configuration (Position 3) Selection

0 — 60 bpm Non-Silenceable

(see note 8)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
8 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Only

Off)
C — NAC 2 Off (see note 7)
0 — 60 bpm Non-Silenceable

(see note 9)

1 — 60 bpm Silenceable

Default

Mode

1

3

2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 2 Off (see note 7)

P/N 06-236716-001 3-9 August 2007

Configuration

Table 3-1. Configuration Settings

Configuration

Number

(Position 1, 2)

32 NAC 2 Releasing

33 NAC 3 First Alarm

Configuration Item Configuration (Position 3) Selection

0 — 60 bpm Non-Silenceable

(see note 10)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 2 Off (see note 7)
0 — 60 bpm Non-Silenceable

(see note 8)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable

Default

Mode

5

1

3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
8 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Only

Off)
C — NAC 3 Off (see note 7)

August 2007 3-10 P/N 06-236716-001

Table 3-1. Configuration Settings

Configuration

Configuration

Number

(Position 1, 2)

34 NAC 3 Pre-Release

35 NAC 3 Releasing

Configuration Item Configuration (Position 3) Selection

0 — 60 bpm Non-Silenceable

(see note 9)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 3 Off (see note 7)
0 — 60 bpm Non-Silenceable

(see note 10)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable

Default

Mode

3

5

36 NACs Used for

General Alarm

3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 3 Off (see note 7)
1 — NAC #1
2 — NAC #2
3 — NAC #1 & NAC #2
4 — NAC #3
5 — NAC #1 and NAC #3
6 — NAC #2 & NAC #3
7 — NAC #1 & NAC #2 & NAC #3
8 — None (No General Alarm)

8

P/N 06-236716-001 3-11 August 2007

Configuration

Table 3-1. Configuration Settings

Configuration

Number

(Position 1, 2)

37 NAC #1 General Alarm 0 — 60 bpm Non-Silenceable

38 NAC #2 General Alarm 0 — 60 bpm Non-Silenceable

Configuration Item Configuration (Position 3) Selection

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 3 Off (see note 7)

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable

Default

Mode

7

7

3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 3 Off (see note 7)

August 2007 3-12 P/N 06-236716-001

Table 3-1. Configuration Settings

Configuration

Configuration

Number

(Position 1, 2)

39 NAC #3 General Alarm 0 — 60 bpm Non-Silenceable

Configuration Item Configuration (Position 3) Selection

1 — 60 bpm Silenceable
2 — 120 bpm Non-Silenceable
3 — 120 bpm Silenceable
4 — Steady Non-Silenceable
5 — Steady Silenceable
6 — Temporal Non-Silenceable
7 — Temporal Silenceable
8 — Intelligent Synchronization - Non-Silenceable
9 — Intelligent Synchronization - Silenceable (Horn &

Strobe)
A — Intelligent Synchronization - Silenceable (Horn Off)
C — NAC 3 Off (see note 7)

NOTES:

1. If "circuit not used" is selected, do NOT install an EOL as the control unit needs to see open
circuit. Using an EOL will cause trouble.

2. DET 1, DET 2, and DET 3/WF will activate first alarm ONLY IF it is part of the ARC activation
condition.

3. SUPV 1 will activate first alarm ONLY IF it is part of the ARC activation condition.

4. If Initiator is selected for any Release circuit output, the respective Power-Limited switch setting
is ignored.

5. The NAC will be driven by both ARC 1 and ARC 2. However the first ARC to reach each state is
given precedence. Once its cycle is complete, the other ARC, if active, will gain control.

6. The NAC may be related to neither ARC if the control unit is used for non-suppression
applications. Also see notes 8 to 10.

7. An OFF condition is different from NOT USED and will require that an EOL be installed.

8. In addition to being selectable for NACx First Alarm, the various tones are also selectable in the
condition that both ARCs are not used and one of DET 1, DET 2 or DET 3/WF is in alarm.

9. In addition to being selectable for NACx Pre-Release, the various tones are also selectable in the
condition that both ARCs are not used and two of DET 1, DET 2 or DET 3/WF are in alarm.

10. In addition to being selectable for NACx Releasing, the various tones are also selectable in the
condition that both ARCs are not used and all of DET 1, DET 2 and DET 3/WF are in alarm.

Default

Mode

7

P/N 06-236716-001 3-13 August 2007

Configuration

August 2007 3-14 P/N 06-236716-001

Operation

4-1 INTRODUCTION

This chapter explains how to read the control unit display, interpret the LEDs, and how to reset
the unit. The following are the operational modes of the control unit:

•Normal Mode

•Alarm Signal

•Supervisory Signal

• Trouble Signal State

4-1.1 Normal Mode

In the normal mode, the control unit continuously monitors all inputs and outputs for any
change of state. In the normal mode the Green AC ON LED is the only illuminated LED. The
buzzer and NACs are silent, The Programmable Relays are de-energized, and the Trouble relay
is energized.

4-1.2 Alarm Signal State

CHAPTER 4

OPERATION

In the Alarm state, the control unit has detected one or more active inputs on its input circuits.
The states of Alarm are:

1. First Alarm — caused when input is received from:

•DET 1, or

•DET 2, or

• DET 3 (Detector or Waterflow), or

• Manual Release

2. Pre-Release — caused when input is received from:

• DET 1 in Single-Zone release mode, or

• DET 2 in Single-Zone release mode, or

• DET 1 and DET 2 in Cross-Zone Mode, or

• DET 1 and DET 3 (Waterflow) in Cross-Zone mode, or

• DET 2 and DET 3 (Waterflow) in Cross-Zone mode, or

• DET 1 and Supv 1 in Cross-Zone mode, or

• DET 2 and Supv 1 in Cross-Zone mode, or

• Manual Release

3. Releasing — caused when the pre-release countdown timer has counted down to zero. In
this state, the control unit is actively in the process of activating its Agent Release
Circuit(s).

4. Post-Release — condition when the control unit has released Agent.

P/N 06-236716-001 4-1 August 2007

Operation

4-1.3 Supervisory Signal

In the supervisory state, the control unit has detected a change in state of one or both of its
supervisory input circuits, or its PCB mounted Output Disable switch. A flashing LED indicates
one or more unacknowledged supervisory events. A steady LED indicates all supervisory
events have been acknowlwdged. The LED turns off when the AEGIS receives supervisory-off
messages from all initiating devices that reported supervisory conditions.

4-1.4 Trouble Signal State

In the trouble state, the control unit has detected one or more active troubles such as AC
failure, open circuits, short circuits, ground faults, activation of abort during non-alarm
condition, and so on. In the trouble mode, the Trouble LED and circuit-specific LED will flash,
the internal buzzer will sound, and the trouble relay will de-energize.

With the exception of microprocessor or PCB troubles, all other troubles may be acknowledged
either automatically (i.e., the trouble event reverts to normal condition) or manually by the
operator by pressing the Acknowledge or System Reset control switches.

4-2 CONTROL SWITCH FUNCTIONALITY

Illegal button presses, or illegal combinations of button presses, shall result in a momentary
display of "Err".

4-2.1 Acknowledge

Pressing the Acknowledge control switch during an active trouble, supervisory, or alarm allows
the operator to signal the AEGIS that a new event currently being displayed is understood. The
AEGIS control unit’s buzzer will silence and all flashing Alarm, Trouble, or Supervisory LEDs
will light steady.

Table 4-1. Acknowledge

Event Circuit Specific LED System Event LED Buzzer

Alarm Steady Steady Off

Trouble Steady Steady Off

Supervisory Steady Steady Off

Event Clear Off Off Off

Event Recurrence Flash Flash On Steady - Alarm

On Pulsed - Trouble/Supervisory

4-2.2 Signal Silence

Pressing the Signal Silence control switch at any alarm state will turn on the Signal Silenced
LED and silence all NACs unless configured otherwise (non-silenceable).

4-2.3 System Reset

Resets the system including turning off outputs and interrupting power to all input and output
circuits for a period of five (5) seconds.

August 2007 4-2 P/N 06-236716-001

4-2.4 Output Disable

Disables the release of agent, and as selected in the system configuration, the activation of
NAC outputs and/or Programmable Relays. This is used when performing maintenance on the
system. When the control switch is engaged, it creates a System Supervisory condition.
Pressing the control switch momentarily toggles in and out of the disable mode.

Operation

P/N 06-236716-001 4-3 August 2007

Operation

August 2007 4-4 P/N 06-236716-001

Testing and Maintenance

CHAPTER 5

TESTING AND MAINTENANCE

5-1 MAINTENANCE REQUIREMENTS

The Kidde AEGIS™ must be inspected, tested and maintained in accordance with the
requirements of NFPA 72 (latest edition), and/or the local Authority Having Jurisdiction (AHJ).

Two different sources of power can be connected to the control unit. Disconnect
both sources of power and critical components such as special extinguishing

WARNING

systems and relays controlling facility-power shutoff before servicing the
control unit. The control unit and associated equipment may be damaged by
connecting or disconnecting wiring while the control unit is energized.

For inspection, testing and maintenance of the associated extinguishing system, refer to the
manufacturers instructions and the standards and codes that apply to that systems.

Prior to any testing or maintenance on the AEGIS, perform the following:

1. Disable ARCs and NACs via the Output Disable control switch.

2. Physically disconnect the wiring to initiator assemblies (if used) from the release-circuit
terminals, short the leads together, and wrap the leads in insulating tape

3. Physically disconnect all control heads (if used) from their associated agent-storage­container discharge valves

4. Physically disconnect the wiring to solenoid valves (if used) for pre-acti on/deluge sprinkler
systems

5. Ensure that emergency operations controlled by this system such as facility power shutoff
are bypassed

6. Notify personnel in the facility and at off-premises monitoring locations that you are
working on the system and that you will inform them when servicing has ended.

5-2 TESTING FREQUENCY

The frequency shall be per NFPA 72 (latest edition) stated below, or as required by the local
Authority Having Jurisdiction (AHJ), whichever is more stringent.

P/N 06-236716-001 5-1 August 2007

Testing and Maintenance

5-3 TESTING

5-3.1 Battery Status Check

1. Disconnect AC power.

2. Allow control unit to operate on the batteries for about one hour.

3. Measure the individual battery voltages. If any battery reads 1.5 V or more below its rated
voltage, that battery should be replaced.

Generally, if one of the batteries is low, the other(s) will soon fail. It is advis able to replace all
the batteries in a set when one requires replacement. Any battery that has been in service for
36 months or more must be replaced.

5-3.2 Battery Test

The following sequence will display the battery open circuit voltage and charge current:

1. Press and hold Acknowledge and Signal Silence control switches simultaneously for fi ve
(5) seconds. As long as both keys are pressed, the battery voltage is displayed for three
(3) seconds, and then the battery current. These alternate every three (3) seconds.

2. The battery test will exit if either control switch is released, or if a control unit status
change occurs.

5-3.2.1 BATTERY VOLTAGE DISPLAY

Battery voltage will be as shown in Figure 5-1. The units are in Volts.

Figure 5-1. Battery Voltage Display

5-3.2.2 BATTERY CHARGE CURRENT DISPLAY

Battery charge current will be as shown in Figure 5-2. The units are in Amps.

Figure 5-2. Battery Charge Current Display

5-3.3 Replacing the Batteries

Before replacing batteries, disconnect AC power. Batteries should be replaced at least once
every 36 months, or as directed by the local Authority Having Jurisdiction. Do not install a
battery set whose open circuit voltage is less than 22 volts.

August 2007 5-2 P/N 06-236716-001

5-3.4 Lamp Test

Use the following procedures to perform the lamp/buzzer test.

1. Verify that the control unit is in normal standby mode with no alarms, troubles or
supervisory conditions.

2. Press and hold the Acknowledge control switch for a period of five (5) seconds. The LEDs
and the digital display characters will illuminate, and the buzzer will sound. This will
continue until the Acknowledge control switch is released, or there is a status change to
the control unit. This will enable malfunctioning LEDs/segments to be visually sighted.

Testing and Maintenance

P/N 06-236716-001 5-3 August 2007

Testing and Maintenance

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 5-4 P/N 06-236716-001

Troubleshooting

CHAPTER 6

TROUBLESHOOTING

6-1 PURPOSE

This chapter provides diagnostic information, probable causes, and the method(s) to return the
Kidde AEGIS to proper operating conditions.

Prior to taking corrective action or performing any maintenance functions, you must refer to
Paragraph 5-1 and follow the instructions specified there.

6-2 TROUBLE DIAGNOSTICS

Diagnostics allow the operator to determine the cause of trouble. To access the diagnostic
function, the control unit needs to have at least one active trouble condition. Perform the
following:

Step Description Display Examples

1 Press and hold the Signal Silence control switch for five (5) seconds. A 3-digit

Trouble code will be displayed until the Signal Silence control switch is
released (sample on right).

2 If multiple troubles exist, the display will blink one second on, one second off,

and the trouble codes will sequence to the next code every time the display
illuminates. When all codes have been displayed, the sequence will repeat until
the Signal Silence control switch is released (sample on right).

6-3 TROUBLE CODES AND CORRECTIVE ACTION

Code Trouble Corrective Action

000 Microprocessor or PCB Replace the PCB.
001 Ground Check for connections to earth ground on field wiring whose removal

restores proper earth-ground offset voltage of 6.60 Vdc nominal.
002 AC Voltage below 85% Check incoming AC power.
003 Primary PSU Output Voltage Check power supply connector, from the power supply to main PCB

(PSU J2).

Replace the power supply assembly.
004 No Secondary Power Connected V erify battery connections to PCB (TB12). In the presence of primary

power, no chargeable batteries can be detected. Either they are too

discharged (<17V), or not connected at all. In either case there will

be no battery charging.
005 Battery Charger Fault Measure Power Supply voltage (27.6 Vdc) (PSU J2). If correct,

replace PCB. If not correct, replace power supply.

P/N 06-236716-001 6-1 August 2007

Troubleshooting

Code Trouble Corrective Action

006 Low Battery Check battery voltage, must be greater than 20.5 Vdc in the absence

of primary power. When voltage drops as low as 19.5 Vdc, the

charger will disconnect and the outputs will be isolated.
007 Reversed Battery Verify Battery polarity.
008 Detector #1 Open Circuit Look for discontinuity in detector #1 wiring.

Check for missing/incorrect value 5.1K resistor.
009 Detector #2 Open Circuit Look for discontinuity in Detector #2 wiring.

Check for missing/incorrect value 5.1K resistor.
010 Detector #3/Waterflow Open

Circuit

Look for discontinuity in Detector #3/Waterflow wiring.

Check for missing/incorrect value 5.1K resistor.
011 Manual Release Open Circuit Look for discontinuity in manual release circuit wiring.

Check for missing/incorrect value 5.1K resistor.
012 Supervisory #1 Open Circuit Look for discontinuity in Supervisory #1 wiring.

Check for missing/incorrect value 5.1K resistor.
013 Supervisory #2 Open Circuit Look for discontinuity in Supervisory #2 wiring.

Check for missing/incorrect value 5.1K resistor.
014 Invalid Abort Abort station activated in non-alarm condition.
015 Abort Open Circuit Look for discontinuity in circuit wiring.
016 ARC #1 Short Circuit Troubleshoot ARC #1 wiring by breaking-up circuit to isolate the

short.
017 ARC #1 Open Circuit Look for discontinuity in ARC #1 wiring.

Check ARC #1 configuration.
018 ARC #2 Short Circuit Troubleshoot ARC #2 wiring by breaking-up circuit to isolate the

short.
019 ARC #2 Open Circuit Look for discontinuity in ARC #2 wiring.

Check ARC #2 configuration.
020 NAC #1 Short Circuit Troubleshoot NAC #1 wiring by breaking-up circuit to isolate the

short.
021 NAC #1 Open Circuit Look for discontinuity in NAC #1 wiring.

Check for missing/incorrect value 5.1K resistor.
022 NAC #2 Short Circuit Troubleshoot NAC #1 wiring by breaking-up circuit to isolate the

short.
023 NAC #2 Open Circuit Look for discontinuity in NAC #1 wiring.

Check for missing/incorrect value 5.1K resistor.
024 NAC #3 Short Circuit Troubleshoot NAC #1 wiring by breaking-up circuit to isolate the

short.
025 NAC #3 Open Circuit Look for discontinuity in NAC #1 wiring.

Check for missing/incorrect value 5.1K resistor.
026 ARC #1 Not Open Circuit Check configuration to make sure ARC #1 is enabled.
027 ARC #2 Not Open Circuit Check configuration to make sure ARC #2 is enabled.
028 Serial Cable Connected Remove serial cable.

August 2007 6-2 P/N 06-236716-001

Parts List

CHAPTER 7

PARTS LIST

Description Part Number

Kidde AEGIS Control Unit 84-732001-001
Kidde AEGIS Control Unit with Switches 84-732001-201
Installation/Configuration Kit 06-220148-002
Operating Instructions 06-236719-002
Replacement Hardware Installation Kit 06-220149-001
Replacement Enclosure Assembly 06-220172-002
Replacement Enclosure Assembly (with Switches) 06-220174-002
Replacement Switch Kit 06-220176-001
Replacement PCB Assembly 06-220150-001
Replacement Power Supply 06-118394-002
Trim Ring 76-600000-007
In-Line Releasing Diode (10K) Kit 06-220023-001
Battery Enclosure 76-100010-001
Dead-Front Panel 06-220175-001
Replacement Bezel Assembly 06-220151-001
Spare Key 06-118013-001
Spare Keylock with Keys 06-129924-001
EOL Backbox (Canadian applications only) 06-129963-002
Battery Harness 06-129925-002

P/N 06-236716-001 7-1 August 2007

Parts List

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 7-2 P/N 06-236716-001

Battery Capacity Calculations

APPENDIX A

BATTERY CAPACITY CALCULATIONS

A-1 STANDBY TIME DURATION

To calculate battery capacity for a specific application, first select the duration for which
standby and alarm power is required using Table A-1.

Table A-1. Duration Time for Standby and Alarm

Type of System Standby Alarm

Local or Central Station (Protected Premises) Fire Alarm Systems per NFPA 72 24 hours 5 minutes
Clean Agent Suppression Systems per NFPA 12, 12A, 12B, and 2001 24 hours 5 minutes
Deluge or Pre-Action Water Spray Systems per Factory Mutual 90 hours 10 minutes

A-2 POWER CONSUMPTION DATA

Table A-2 lists the power consumption of the various system components.

Table A-2. Power Consumptions for System Components

Number Component Standby Power (mA) Alarm Power (mA)

1
2
3 Programmable Relays 0.00 20.00

4 Ionization/Photoelectric/Electronic Heat Detectors 0.07 70.00
5

6
7
8
9

10

1

The standby and alarm values for the AEGIS include the Trouble Relay.

2

The Auxiliary Power Output current value stated is the maximum allowed.

3

The Standby current stated for Ionization, Photoelectric, Electronic Heat, Duct and Contact Heat Detectors is
for each detector. The Alarm current is for the Detection Circuit.

4

The current value stated for the Notification Appliance Circuits is the maximum each.

5

For the Alarm current values of Steady Release Solenoids, refer to Appendix B.

6

Momentary Agent Release Solenoids and Initiators are negligible in their current requirements and do not
need to be included in the calculation.

Kidde AEGIS™ Control Unit
Auxiliary Power Output

DH-60 (2W) Duct Detectors
Contact Type Heat Detectors
NACs 1, 2, and 3
Release Solenoids - Steady
Release Solenoids - Momentary
Release - Initiators

4

6

1

2

3

3

5

6

100.00 240.00

1000.00 Max. 1000.00 Max.

0.07 70.00

0.00 70.00

0.00 1500.00 each

0.00 Refer to Appendix B

0.00 0.00

0.00 0.00

P/N 06-236716-001 A-1 August 2007

Battery Capacity Calculations

A-3 STANDBY AND ALARM POWER REQUIREMENTS

Use Table A-3 to calculate the Standby and Alarm Power requirement of the Kidde AEGIS.

A-3.1 Procedure

1. Insert the actual count of components and devices into the Standby Quantity column.

2. Insert the quantity of these components devices which can be in alarm into the Alarm
Quantity column.

3. Multiply the quantity count by the Each — Standby and Alarm Power and insert these
values into the Total column.

4. Calculate the sum of the values in the Total Standby and Total Alarm columns to arrive
at the Total Standby Power and Total Alarm Power in milliamperes.

5. Divide the mA values for Total Power in Amperes.

Table A-3. Standby and Alarm Calculation Guide

Standby Power (mA) Alarm Power (mA)

Number Component

Qty Each Total Qty Each Total

1 AEGIS Control Unit 1 100.00 100.00 1 240.00 240.00
2

3
4

Auxiliary Power Output
Programmable Relays

Detection Circuits 1, 2, and 3
5 Ionization Detectors 0.07 0.00
6 Photoelectric Detectors 0.07 0.00

1

2

3

1000.00 1000.00

0.00 0.00 20.00

0.00 0.00 70.00

7 Electronic Heat Detectors 0.07 0.00
8 DH-60 (2W) Duct Detectors 0.07 0.00
9 Contact Type Heat Detectors 0.00 0.00 0.00

10
11

NACs 1, 2, and 3

Release Solenoids

4

5

0.00 0.00 1500.00

0.00 0.00 0.00

Total Power in mA

Total Power in Amperes

1

The Auxiliary Power Output current value stated is the maximum allowed. See Note 6 below.

2

The value stated for the Programmable Relays is for each individual relay when energized.

3

Standby currents should be considered for all Ionization, Photoelectric, Duct and Heat Detectors in the three
Detection Circuits. However, since only one detector can be in Alarm, the Alarm current should only be con­sidered for the entire Detection Circuit.

4

The value stated for the NACs is the maximum for each. See Note 6 below.

5

For the Alarm current values of Steady Release Solenoids, refer to Appendix B.

6

Since the Power Supply of the Kidde AEGIS unit is rated at 5.4 Amps, the system designer should ensure
that the system circuits are loaded so as to keep the calculated alarm current equal to or less than 5.4
Amps.

August 2007 A-2 P/N 06-236716-001

A-4 BATTERY CAPACITY CALCULATIONS

Based on the “Duration” for which battery backup is required (refer to Paragraph A-1) and the
Total Standby Power and Total Alarm Power values (refer to Paragraph A-3), the next step
is to calculate the battery capacity in Ampere-Hours (AH) using Table A-4.

Table A-4. Battery Capacity Calculations

Battery Capacity Calculations

Total Power Required (Amps)

Total Standby Current (Amps) = x =
Total Alarm Current (Amps) = x =
Total Calculated AH (column sum) =
Required Battery AH using 110% Deration Factor
(multiply Total Calculated AH by 1.1)
Selected Battery Capacity
(must be greater than or equal to required battery AH and lower than 68 AH)

Multiply ByDuration

(Hours)

Equals Ampere-Hour (AH)

=

=

Note: 1. The above battery capacity calculation and subsequent selection assumes that the

battery is installed in ambient room temperatures. If installed in below ambient, consult
the battery manufacturer for requirement of additional deration factors not considered
above.

2. 5 minutes = 0.083 hours
10 minutes = 0.167 hours

P/N 06-236716-001 A-3 August 2007

Battery Capacity Calculations

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 A-4 P/N 06-236716-001

List of Agency Listed Compatible Devices

APPENDIX B

LIST OF AGENCY LISTED COMPATIBLE DEVICES

B-1 DETECTORS AND BASES

Table B-1. Detectors and Bases

Device Model Part Number

Ionization Smoke Detector CPD-7051 70-510000-001
Ionization Detector Duct Head CPD-7051D 70-510000-060

Advanced Ionization Smoke Detector CPD-7054 70-540000-001
Advanced Ionization Detector Duct Head CPD-7054D 70-540000-002

Photoelectric Smoke Detector PSD-7155 71-550000-001
Photoelectric Detector Duct Head PSD-7155D 71-550000-060
Photoelectric Smoke Detector PSD-7155P 71-550000-002

Photoelectric Detector with 135

Advanced Photoelectric Smoke Detector PSD-7157 71-570000-001
Advanced Photoelectric Detector Duct Head PSD-7157D 71-570000-002

Electronic 135°F Fixed with 15°F ROR Heat Detector

°F Sensor

PSD-7156 71-560000-001

THD-7052 70-520000-001

Electronic 135
2-Wire Detector Base 2WB 70-501000-001

2-Wire Detector Base 2WRLT 70-501000-002
2-Wire Detector Base 2WRB 70-501000-005
2-Wire Relay Module 2WRM 70-500000-004
2-Wire Duct Housing DH-60-2W 70-600000-200
2-Wire Duct Housing with CPD-7051D DH-60-2CPD 70-600000-251
2-Wire Duct Housing with CPD-7054D DH-60-2ACD 70-600000-254
2-Wire Duct Housing with PSD-7155D DH-60-2PSD 70-600000-255
2-Wire Duct Housing with PSD-7157D DH-60-2APD 70-600000-257
4-Wire Detector Base 4WRB 70-501000-101
4-Wire Duct Housing less Detector with Integral Exhaust

Tube & 24/120/240 VAC Transformer
4-Wire Duct Housing with Original Ionization Detector

CPD-7051D
4-Wire Duct Housing with Advanced Ionization Detector

CPD-7054D
4-Wire Duct Housing with Original Photoelectric Detector

PSD-7155D
4-Wire Duct Housing with Advanced Photoelectric Detector

PSD-7157D

°F Fixed Temp Heat Detector

THD-7053 70-530000-001

DH-60 70-600000-000

DH-60-CPD 70-600000-051

DH-60-ACD 70-600000-054

DH-60-PSD 70-600000-155

DH-60-APD 70-600000-157

P/N 06-236716-001 B-1 August 2007

List of Agency Listed Compatible Devices

Ta b l e B -2. Releasin g S o lenoid

Wire Length (ft.)

I

Device

(Min.)

Amps

Resistance

(Max.)

Ohms

On Time

12

AWG

14

AWG

16

AWG

18

AWG

890181 2.4 10 Momentary 300 200 120 — 1 or 2 UL, FM
895630 2.0 12 Momentary 300 200 120 — 1 or 2 UL, FM
899175 2.20 10.8 Momentary 300 200 120 — 1 or 2 UL, FM
48650001 0.24 103 Steady 3000 2000 1200 800 1 or 2 UL, FM
06-118329-001 0.225 108 Steady 3000 2000 1200 800 1 or 2 FM
06-118384-001 0.52 46 Steady 1440 760 480 340 1 or 2 UL
38-509834-001 0.632 38 Steady 1050 550 330 240 1 or 2 UL, FM
38-509837-001 0.4 60 Steady 2300 1460 915 570 1 or 2 UL, FM
81-100000-001 0.44 59 Steady 2300 1460 915 570 1 or 2 UL, FM
87-120099-001* 2 12 Momentary 360 240 140 — 1 or 2 UL, FM
60-120099-001* 2 12 Momentary 360 240 140 — 1 or 2 UL, FM

Max.

Number per

Circuits

Agency

87-120099-600* 2 12 Momentary 360 240 140 — 1 or 2 UL, FM
897494-000 1.5 14.2 Steady 380 240 150 — 1 UL, FM
897494-530 1.5 14.2 Steady 380 240 150 — 1 UL, FM
90-487100-001* 2 12 Momentary 360 240 140 —— 1 or 2 UL, FM
FM Group A 0.458 52 Steady 1440 760 480 340 1 FM
FM Group B, D 0.7 34 Steady 940 500 300 220 1 FM
FM Group E, G 0.42 57 Steady 1570 760 525 370 1 FM
FM Group F Skinner 24 Vdc, 22 Watt Solenoid 7312BN4TNLVNOC322C2 1 FM
FM Group I Victaulic 24 Vdc, 8.7 Watts, 364 mA series 753-E Solenoid 1 FM
FM Group J Viking Model No. 11591, 11592, 11595, and 11596, 24 Vdc, 10 Watts 1 FM
FM Group K Viking Model No. 11601, 11602, and 13215, 24 Vdc, 9 Watts 1 FM

* Must be used in conjunction with Microswitch P/N 87-120039-001 for momentary operation.

Table B-3. Initiator-Based Releasing Devices

Device

I (Min.)

Amps

83-131025-001 * 3 Momentary 1

Resistance

(Max.) Ohms

On Time

Max. Number

per Circuits

Agency

* The maximum circuit resistance for this device must be 10 ohms, regardless of the number used. The firing current will be

2.5 Amps.

Table B-4. Miscellaneous Devices

Device Model Number Supplier/Mfg.

Receiving Units for Central Station 5104B Silent Knight

August 2007 B-2 P/N 06-236716-001

Technical Specifications

APPENDIX C

TECHNICAL SPECIFICATIONS

Item Description

ANUMBER OF HAZARDS One (1)
BPOWER

AC Main Input 120 Vac/240 Vac 50/60 Hz (90 to 264 Vrms, 47 to 63 Hz)
Current Consumption
120 Vac:
240 Vac:
Required Breaker 15 Amps
Power Supply Output 5.4 Amps @ 27 Vdc
Battery Charger Output 6 Amps @ 27 Vdc
Battery Capacity Up to 68 AH @ 24 Vdc
Battery Cutout Voltage 18.6 Vdc

3.2 Amps

1.6 Amps

Auxiliary Power Output 1 Amp maximum @ 24 Vdc Nominal
Battery Transfer 85% of 120 Vac

85% of 240 Vac

C Input Circuits

C.1 Detection Circuits Three (3)

- Two (2) for Suppression Input

- Third configurable as either independent Detection Circuit or
for Waterflow

Compatible Devices - 25 conventional electronic Smoke/Heat detectors listed in

Appendix B.

- A quantity of Normally-Open contact-closure devices subject
to maximum allowable wiring resistance.

Circuit Type - Class A (Style D) or Class B (Style B) supervised

- Detects Opens and Ground Faults

- Power Limited
Circuit Voltage Nominal 24 Vdc, 28 Vdc maximum
Maximum Line Resistance 100 ohms per loop
Maximum Alarm Current 70 mA
End-of-Line Resistor 5.1K, 5%, 1/2 W

P/N 06-236716-001 C-1 August 2007

Technical Specifications

Item Description

C.2 Manual Release One (1)

Compatible Devices A quantity of Normally-Open contact-closure devices subject to maximum

allowable wiring resistance.

Circuit Type - Class A (Style D) or Class B (Style B) supervised

- Detects Opens and Ground Faults

- Power Limited
Circuit Voltage Nominal 24 Vdc, 28 Vdc maximum
Maximum Line Resistance 100 ohms per loop
Maximum Current 10 mA
End-of-Line Resistor 5.1K, 5%, 1/2 W

C.3 Abort Input One (1)

Compatible Devices A quantity of Normally-Open contact-closure devices subject to maximum

allowable wiring resistance.

Circuit Type - Class A (Style D) or Class B (Style B) supervised

- Detects Opens and Ground Faults

- Power Limited
Circuit Voltage Nominal 24 Vdc, 28 Vdc maximum
Maximum Line Resistance 100 ohms per loop
Maximum Current 10 mA
End-of-Line Resistor 5.1K, 5%, 1/2 W

C.4 Supervisory Input Two (2)

Compatible Devices A quantity of Normally-Open contact-closure devices subject to maximum

allowable wiring resistance.

Circuit Type - Class A (Style D) or Class B (Style B) supervised

- Detects Opens and Ground Faults

- Power Limited
Circuit Voltage Nominal 24 Vdc, 28 Vdc maximum
Maximum Line Resistance 100 ohms per loop
Maximum Current 10 mA
End-of-Line Resistor 5.1K, 5%, 1/2 W

August 2007 C-2 P/N 06-236716-001

Item Description

D OUTPUT CIRCUITS

D.1 Notification Appliance Three (3)

- NAC 1: First Alarm Condition

- NAC 2: Pre-Release Condition

- NAC 3: Release Condition

Compatible Devices A quantity of Polarized 24 Vdc Notification Appliances subject to the

maximum current and maximum allowable voltage drop per circuit.

Circuit type - Class A (Style Y) or Class B (Style Z) supervised

- Detects Opens and Ground Faults

- Power Limited

Circuit Voltage Nominal 24 Vdc, 28 Vdc maximum

Technical Specifications

Total Voltage Drop at End-of-

2 V

Line
End-of-Line Resistor 5.1K, 5%, 1/2 W

D.2 Output Relays Four (4)

- Programmable: Three (3), normally de-energized with power on

- Trouble: One (1), normally energized with power on
Relay Type Voltage free, Form-C (1 N.O. and 1 N.C.)
Contact Rating 3 Amps @ 30 Vdc (resistive)

D.3 Releasing Circuits Two (2)

- ARC 1

- ARC 2
Compatible Devices On each circuit the following devices listed in Appendix B

- 1 or 2 Control Head Solenoids

- 1 Initiator

- 1 or 2 FM Pre-Action/Deluge/Sprinkler Solenoids
Releasing Configurations - Solenoids on both ARC 1 and ARC 2

- Solenoids on ARC 1 and one Initiator on ARC 2 or vice-versa

- One Initiator on both ARC 1 and ARC 2
Circuit Type - Class B (Style Z) supervised

- Detects Opens and Ground Faults

Operating Voltage Nominal 24 Vdc, 28 Vdc maximum
End-of-Line Resistor Not required

P/N 06-236716-001 C-3 August 2007

- Normally no Short detection and non-Power Limited

- Except with Initiators, power limiting and short circuit detection options

enabled with In-line Diode-Resistor device

Technical Specifications

Item Description

EENCLOSURE

Degree of Protection NEMA 1
Material of Construction 18 Gauge (0.053 inches or 1.35 mm) sheet steel
Color Red
Assembled Dimensions

- With Standard Door

14-1/4 in. Width x 5 in. Depth x 19 in. Height
(362 mm x 127 mm x 483 mm)

- With Switch-Door

Approximate Weight (without
batteries)

- Standard Assembled

- Standard Shipping

- Canadian Assembled with
Dead-Front Panel

- Dead Front Panel Shipping

- Switch Panel Assembled

- Switch Panel Shipping

F OPERATING ENVIRONMENT

Temperature 32°F to 120°F (0°C to 49°C)
Relative Humidity

14-1/4 in. Width x 6 in. Depth x 19 in. Height
(362 mm x 152 mm x 483 mm)

18 lbs. (8 kg)
21 lbs. (9 kg)
22 lbs. (10 kg)
4 lbs. (2 kg)
19 lbs. (8 kg)
21 lbs. (10 kg)

93% RH @ 90

°F

August 2007 C-4 P/N 06-236716-001

FM Rules for PreAction/Deluge Systems

APPENDIX D

FM RULES FOR PREACTION/DELUGE SYSTEMS

Kidde AEGIS™ applications which require Factory Mutual (FM) approved Pre-Action and/or
Deluge Systems must conform to the following guidelines:

• Detection Zone 1 (Det1), Detection Zone 2 (Det2) and Waterflow (W'Flow) Initiating
Circuits must be configured for Class A, Style D wiring.

• The Battery backup system must provide for 90 hours of Standby operation followed by 10
minutes of Alarm operation. Refer Appendix A for calculations.

• The Agent Release Output must be configured for Deluge Solenoid activation. The Solenoid
Activation Time must be set either for:

– 10 minutes, or
– 15 minutes, or
– On-until-reset.

The wiring connection of the Control Unit to the Deluge Solenoids must be as detailed in the
Installation section of this Manual.

P/N 06-236716-001 D-1 August 2007

FM Rules for PreAction/Deluge Systems

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 D-2 P/N 06-236716-001

Central Station Operation

APPENDIX E

CENTRAL STATION OPERATION

The Kidde AEGIS™ should be configured for Central Station operation as follows:

• One of the three (3) Programmable Relays should be configured for any alarm. For
example:

2,

1

3, OR
4

• The Trouble Relay should be set to delay AC Failure Response by a period acceptable to
the local AHJ. For example:

1

Refer to Chapter 3 for details on how to enter or change configuration settings.

15

1

X

A Silent Knight DACT Model 5104B must be wired to the control unit, as shown in Figure E-1.
Refer to the Model 5104B Installation Manual for information regarding connection of the DACT
to telephone lines for Alarm and Trouble transmission(s).

Note 1: Wiring must be installed in conduit within 20 feet.
Note 2: Central Station is not suitable for use with Canadian applications.

TB 8

TROUBLE

RELAY

PROGRAMMABLE

PROGRAMMABLE

PROGRAMMABLE

PROGRAMMABLE

RELAYS

RELAYS

RELAYS

RELAYS

4.7K

TB 9, TB10, or TB11

TB 9, TB10, or TB11

4.7K

4.7K

SUPERVISORY

TB 9, TB10, or TB11

TB 9, TB10, or TB11

4.7K

4.7K

PROGRAMMED FOR

GENERAL ALARM

CONTROL PANEL

CNCNO

CNCNO

CNCNO

2

1

4567891011

23

1

SILENT KNIGHT 5104B DACT
INITIATING DEVICE CIRCUITS

P/N 06-236716-001 E-1 August 2007

Figure E-1. Wiring for the DACT

Central Station Operation

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 E-2 P/N 06-236716-001

Routings for Power-Limited and Non-Power-Limited Wiring

APPENDIX F

ROUTINGS FOR POWER-LIMITED AND

NON-POWER-LIMITED WIRING

This appendix provides guidelines for power-li mited and non-power-limited wiring requirements.
The following wiring requirements shall be observed:

• Power-limited and non-power-limited wiring must be physically separated within the
control-unit enclosure

• All power-limited wiring must be separated by at least 1/4-inch (6 mm) from any
non-power-limited wiring

• Power-limited and non-power-limited wiring cannot enter and exit the control-unit
enclosure through the same knockout or conduit.

Figure F-1 shows typical wiring for power-limited and non-power-limited circuits.

TB8

TB9

TB10

TB11

TB6

TB7

TB5

TB2

TB3TB4

TB1

USE LEFT-SIDE GUTTER FOR

NON-POWER-LIMITED WIRING

RELEASE CIRCUITS

(TB14 AND TB15) CAN BE

WIRED AS POWER-LIMITED

OR NON-POWER-LIMITED

BATTERY WIRING

TB12

TB19

TB13

TB14

TB16TB15

TB17

TB18

MAINTAIN 1/4-INCH SEPARATION BETWEEN

POWER-LIMITED AND NON-POWER-LIMITED WIRING

Figure F-1. Power-Limited and Non-Power-Limited Wiring

USE RIGHT-SIDE GUTTER FOR
POWER-LIMITED WIRING

P/N 06-236716-001 F-1 August 2007

Routings for Power-Limited and Non-Power-Limited Wiring

THIS PAGE INTENTIONALLY LEFT BLANK.

August 2007 F-2 P/N 06-236716-001

Kidde, Fenwal and HSSD are registered trademarks of Kidde-Fenwal, Inc.
All other trademarks are property of their respective owners.

A UTC Fire & Security Company

400 Main Street
Ashland, MA 01721
Ph: 508.881.2000
Fax: [phone]

www.kiddefiresystems.com

These instructions do not purport t o cover all the detai ls or variations in the e quipment
described, nor do they provide for every possible contingency to be met in connection with
installation, operation and maintenance. All specificat ions subject to change without no­tice. Should further information be desired or should particular problems arise which are
not covered sufficiently for the purchaser’s purposes, the matter should be referred to
KIDDE-FENWAL INC., Ashland, Massachusetts

P/N 06-236716-001 Rev. AB ©2007 Kidde-Fenwal, Inc. All Rights Reserved.
Printed in USA