Kidco G35d User Manual [en, es, fr]

Wood Center Gateway® Model G35d

for openings 28” to 36”

Optional extension kit Model G5.5 (2 extensions per kit) necessary for the following widths:

35

3/4”-411/2” - One extension kit / 411/4”-47” - Two extension kits.

Barrière Wood Center Gateway® modèle G35c pour les ouvertures de 71 à 91.5 cm

Kit de rallonges facultatif modèle G5.5 (2 rallonges par kit) nécessaire pour les largeurs suivantes:

91 à 105,5 cm – Un kit de rallonges / 105 à 119 cm ) – Deux kits de rallonges.

Reja Center Gateway® de madera Modelo G35 para aberturas de 28” a 36”

Juego de extensión opcional Modelo G5.5 (2 extensiones por juego) necesario para las siguientes anchuras:

35

3/4”-411/2” – Juego de una extensión / 411/4”-47” – Dos juegos de extensión.

Bl. 3001-765 • G35d-0407

User Guide

Patents

5,396,732
6,301,832
6,308,462
6,347,483
6,370,823

Important Information

Maintenance

Extension Placement Guide

Parts Check List
Liste de contrôle des pièces
Lista de verificación de piezas

(b) - 2 (c) - 4 (d) - 1 (g) - 1 (h) - 2 (i) - 2

(j) - 4 (k) - 2

Note: To prevent over extension

of spindles, notches have
intentionally been cut into the
threads approximately 1

3/8” from

the pad ends.

Remarque: Pour empêcher la
surextension des axes, des crans
ont été intentionnellement
découpés dans les filets, à 3,5 cm
environ des extrémités
rembourrées.

Nota: Para evitar la extensión
excesiva de los pivotes,
intencionalmente se han hecho
ranuras en las roscas a
aproximadamente 1

3/8" de los

extremos de las almohadillas.

2

Pressure Hinge (p)
Charnière à pression (p)
Bisagra de presión (p)

Stopper (q)
Butée (q)
Tope (q)

Locator (l)
Repère (l)
Localizador (l)

Pressure plate (o)
Plaque de pression (o)
Placa de presión (o)

Button (r)
Bouton (r)
Botón (r)

Handle (n)
Poignée (n)
Asa (n)

Hinge (m)
Charnière (m)
Bisagra (m)

Gate
Barrière
Reja

WARNING

(s) - 2

3

FOLLOW THESE
INSTRUCTIONS
CAREFULLY AND
KEEP THEM FOR
FUTURE
REFERENCE

This gate is designed for children from 6 months to
24 months. Since each child’s skills develop at dif­ferent ages, these parameters should be
monitored against your child’s own development.

When installed as instructed, between two clean
structurally sound surfaces, this gate conforms to:
ASTM F-1004-07 United States Standards

EN 1930:2000 European Standards

• No part of gate requires lubrication.

• Clean using warm, soapy water or a damp

cloth.

Important Information

Maintenance

• Intended for use with children from 6
months through 24 months.

• Check the stability of the gate and tighten

all hardware and mountings regularly.

• To prevent serious injury or death,
securely install gate or enclosure and use
according to manufacturer’s instructions.

• Never use with a child able to climb over or

dislodge/open the gate or enclosure.

• Never use if gate is less than 3/4 of
child’s height.

• Do not use if any part of the gate is
broken or missing.

• This product will not necessarily prevent

all accidents. Never leave child
unattended.

• Use only spare parts available from

KidCo.

• Never allow child to climb or swing on gate.

• Use only with the locking/latching

mechanism securely engaged.

• Never use gate at top of stairs.

• Discontinue use if any part of gate is

damaged.

• Never climb over the gate.

• Never hang or tie toys etc. to any part

of the gate.

ENG

• Do not use abrasive cleaners or bleach.

Extension Placement Guide

Some overlap is intended for variations in wall construction.

28”-31

1/8” Gate

30

3/4”-331/2” Gate + 1 extension - may be placed on either end

33

1/8”-36” Gate + 2 extensions - one on each end

35

3/4”-383/4” Gate + 3 extensions - 2 on one end, 1 on other end

385/8”-411/2” Gate + 4 extensions - 3 on one end, 1 on other end

41

1/4”-44” Gate + 5 extensions - 3 on one end, 2 on other end

433/4”-47” Gate + 6 extensions - 3 on each end

No more than 2 extension kits (6 extensions) recommended per gate.
Extensions must be added as shown.

{
{

{

WARNING

Basic Gate

Included with gate

One optional
extension kit

Two optional
extension kits

4

Operation

Warranty

1. The gate must be installed in a structurally

sound opening. Never install between two
railings or two stair posts. Ensure mounting
surface (wall, doorframe, stair post, etc.) is strong,
rigid and is smooth, clean and grease free.

If mounting onto brick, drywall or other
surfaces, an optional gate installation kit,
wooden board mounted to the surface or
additional hardware may be necessary to
provide a solid, smooth surface.

Measure opening to determine if extensions are
needed. Correct width will be reached by
adjusting all 4 corner spindles. Each spindle
adjusts individually and may be extended to
varying lengths (up to 1

3/4” each) to allow for

molding, uneven walls, etc.
If using gate on a stairway, it must be placed on

the lowest stair on bottom.

2. Spindle attachment is different when using

extensions and when not using extensions.

If no extension/s are used, slide top spindles (b)
and bottom spindles (s) into spindle housing end
without tab (c).
Push assembly into gate corners.

3. If using extension/s, (see Extension Placement

Guide) insert square extension tubes (j) into gate
ends. Connect the bar (k) to one upper exten­sion housing (h) and one lower extension hous­ing (i). Push assembly over extension tubes.
There should be no metal showing from extension
tubes. It may be necessary to apply pressure to
tubes to ensure they are fully inserted into gate
ends. Slide top spindles (b)

and bottom spindles

(s)

into extension tubes.

4. Note: Spindle housings are not used if

square extension tubes are necessary. If the
housings have been inserted, remove with a
screwdriver.

5. Center the gate in opening with bottom rail

resting on floor. Gaps on each side should be
equal. Open the handle to the raised position by
pressing the button (r) and lifting the handle (n) at
the same time.
BUTTON MUST ALWAYS BE PRESSED IN WHEN
LIFTING HANDLE. FAILURE TO DO SO WILL
RESULT IN HANDLE MECHANISM BREAKING.

6. Pull out the two bottom spindles (s) until
they touch mounting surface and rest on top of
floor molding (if applicable). (6a.) Tighten nuts
TOWARD GATE FRAME as tightly as possible
using wrench (g) provided. Each spindle adjusts
individually and may be extended to varying
lengths to allow for molding, uneven walls, etc.

7. Close walk through door so locator (l) is

aligned directly above bottom gate rail. Do not
lower handle. Pull out the top spindle (b) on the
hinge side (m) until it touches the mounting
surface. Tighten nut TOWARD GATE FRAME
until locator drops and rests on bottom gate rail.

8. Pull out spindle (b) in the handle side until
it touches mounting surface and tighten nut
TOWARD GATE FRAME so the distance
between pressure plate (o) and pressure
hinge (area A) is sufficient for walk through
door to open in either direction.

9. Close the handle and check all hardware.
If correctly installed, gate should be firmly in
place. Once opened, the walk through door
should operate easily in either direction.

A pressure indicator (d) has been included as
an additional safeguard. Lift handle (n) and
locate groove on underside. Return handle
to closed position and place indicator hook
under groove. Push in button (r) while pulling
pressure indicator up. Black gauge within
indicator will start moving down.
Recommended pressure is between 3 and 5.
If gauge is more than 5, loosen nut on handle
spindle (b). If less than 3, tighten handle
spindle nut.

If unable to obtain recommended pressure it
is important to know that gate is not
defetive. Gate requires a strong, rigid surface
to maintain pressure. It may be necessary to
consult a hardware store or baby proofer to
find a solution for safe installation.

Installation

Operation

10. To Open Gate:

Release locking mechanism by pressing button
(r) in while lifting handle (n). BUTTON MUST
ALWAYS BE PRESSED IN WHEN LIFTING
HANDLE. Lift walk through door so hinge is
raised and door will swing open in either
direction.

To Close Gate:

Lift walk through door. Position locator (l) until
it is above the bottom rail. Make sure hinge has
dropped down. Push handle down to lock. Gate

should always be in locked position when in
use.

11. Installation Aid

KidCo has available OPTIONAL Y spindles
(Model GY-1 Spindle) to assist in installation
when the mounting surface has a round
baluster. These spindles are used in place of the
spindles included with the basic gate. They may
be ordered through your local KidCo dealer or
direct from KidCo.

No more than 2 Y spindles may be used per
gate and both must be used on the same
side.

Warranty

KIDCO LIMITED WARRANTY

Your KidCo product is warranted to be free from manufacturing defects for a period of one
year from date of purchase under normal non commercial use and in compliance with the
operating instructions. This warranty extends only to the original retail purchaser and is only
valid when supplied with proof of purchase.

KidCo will either repair, or at our option replace, free of charge, any parts necessary to
correct defects in material or workmanship during the warranty period. This warranty is
complete and exclusive. The warranty expressly disclaims liability for incidental, special and
consequential damages of any nature. Any implied warranty arising by operation of law shall
be limited in operation to the terms of this warranty. Some states do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which vary from state to state.

SHOULD REPAIR OR PARTS BE NECESSARY

Should a repair be needed during the warranty period, ship the gate in the original carton or
similar protective container (check any retail store or purchase from UPS) and send freight
prepaid (we suggest UPS) to:

KidCo, Inc., 1013 Technology Way, Libertyville, IL 60048-5349.

Include a note with your return address, day-time telephone number, and specify what is
wrong with the product. Repairs can normally be made within 48 hours after receipt at KidCo.
For additional information CALL our customer service department at [phone].

5

6

InstallationRemarques importantes

Entretien

ATTENTION

LIRE ATTEN­TIVEMENT CES
INSTRUCTIONS ET
LES CONSERVER
POUR POUVOIR
S’Y RÉFÉRER
ULTÉRIEUREMENT.

Cette barrière de sécurité a été conçue pour les
enfants âgés de 6 à 24 mois. Comme les
capacités de chaque enfant se développent à des
âges différents, le facteur âge doit être ajusté en
fonction du propre développement de l’enfant.

Quand elle est installée selon les instructions entre
deux surfaces propres et solidement charpentées,
la barrière est conforme aux normes suivantes :

ASTM F-1004-07 United States Standards
EN 1930:2000 Normes européennes

• Utilisation prévue: enfants âgés de 6 à 24 mois.

• Vérifier la stabilité de la barrière et resserrer

régulièrement toute la quincaillerie et les
supports.

• Pour écarter tout risque de blessure grave,

voire mortelle, installer solidement la
barrière ou la fermeture et utiliser confor-
mément aux instructions du fabricant.

• Ne jamais utiliser pour un enfant capable

de grimper par-dessus la barrière ou la
fermeture ou de la retirer.

• Ne jamais utiliser si la barrière ne mesure

pas au moins les trois quarts de la taille de
l’enfant.

• Ne pas utiliser si une pièce de la barrière

est cassée ou manquante.

• Ce produit n’empêchera pas nécessaire-

ment tous les accidents. Ne jamais laisser
un enfant sans surveillance.

• Utiliser uniquement des pièces détachées

KidCo.

• Ne jamais laisser un enfant grimper sur la

barrière ni la secouer.

• Utiliser uniquement avec le mécanisme de

verrouillage/blocage solidement enclenché.

• Ne jamais utiliser la barrière en haut d’un

escalier.

• Cesser l’utilisation si un composant
quelconque de la barrière est endommagé.

• Ne jamais grimper sur la barrière.

• Ne jamais suspendre ni attacher de jouets,

etc. sur une partie quelconque de la
barrière.

• Aucune partie de la barrière n’exige de
lubrification.

• Nettoyer à l’aide d’une éponge avec de

l’eau chaude et un détergent doux.

• Ne pas utiliser de nettoyants abrasifs ou un

agent blanchissant.

FRE

Guide de mise en place des rallonges

Barrière de base

Fourni avec
la barrière

Un kit de rallonges
facultatif

Deux kits de
rallonges facultatifs

Un chevauchement est prévu pour tenir compte des variantes de construction murale.

71.1 - 79 cm Barrière

78.1 - 85.1 cm Barrière + 1 rallonge peut être placée d’un côté ou de l’autre

84.1 - 91.4 cm Barrière + 2 rallonges une de chaque côté

90.8 - 98.4 cm Barrière + 3 rallonges 2 d’un côté, 1 de l’autre côté

98.1 - 105.4 cm Barrière + 4 rallonges 3 d’un côté, 1 de l’autre côté

104.8 - 111.8 cm Barrière + 5 rallonges 3 d’un côté, 2 de l’autre côté

111.1 - 119.4 cm Barrière + 6 rallonges 3 de chaque côté

Pas plus de 2 kits de rallonges (6 rallonges) recommandés par barrière.
Les rallonges doivent être ajoutées comme indiqué sur l’illustration.

{
{
{