Kidco G150 User Manual

User Guide

Architectural Series

Patents

6,370,823 6,301,832 6,308,462 6,347,483 5,396,732

G150

Premier Gateway Model G150

For openings 29” to 37”

Optional extension kits available

Premier Gateway Modéle G150

Pour des overtures de 73 a 94 cm

Ensembles de rallonges facultatifs disponibles

Reja Premier Gateway Modelo G150

Hay disponibles juegos de extension opcionales

Para aberturas de 29” – 37”

INDEX

ENG

FRE

SPA

User Guide

Parts Check List ............................... 2

Assembly and Installation ....................... 4-6

Warranty..................................... 6

Parts Price List ................................ 15

Method of Payment ............................ 16

Illustrations ................................... 20-21

Guide d’utilisation

Liste de Contrôle des Pièces ..................... 2

Montage et installation.......................... 7-9

Garantie ..................................... 10

Liste des prix des piéces ........................ 15

Mode de Paiement ............................. 17

Figures ...................................... 20-21

Guía del usuario

Lista de Verificación de Piezas ................... 3

Instalación y montaje ........................... 11-13

Garantía ..................................... 14

Lista de precious de las piezas ................... 15

Metodo de Pago .............................. 18

Ilustraciones .................................. 20-21

Parts Check List Liste de des pièces Lista de verificación de piezas

Pressure Hinge (p) Charnière à pression (p) Bisagra de presión (p)

Buttons (r) Boutons (r) Botones (r)

Lower Indicator (t) Indicateur inférieur (t) Indicador inferior (t)

Stopper (q) Butée (q) Tope (q)

Pressure plate (o) Plaque de pression (o) Placa de presión (o)

Locator (l) Repère (l) Localizador (l)

Upper Indicator (s) Indicateur supérieur (s) Indicador superior (s)

Gate Barrière Reja

Handle (n) Poignée (n) Asa (n)

Hinge (m) Charnière (m) Bisagra (m)

Note: To prevent over extension of spindles, notches have intentionally been cut into the threads approximately 1 the pad ends.

” from

Remarque: Pour empêcher la surextension des axes, des crans ont été intentionnellement découpés dans les filets, à 3,5 cm environ des extrémités rembourrées.

(b) - 2 (c) - 4 (h) - 2 (i) - 2

(j) - 4 (k) - 2

(s) - 2

Nota: Para evitar la extensión

excesiva de los pivotes, intencionalmente se han hecho ranuras en las roscas a aproximadamente 1 extremos de las almohadillas.

” de los

Important Information

ENG

FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE

WARNING

• Intended for use with children from 6 months

through 24 months.

• Check the stability of the gate and tighten all

hardware and mountings regularly.

• To prevent serious injury or death, securely install

gate or enclosure and use according to manufacturer’s instructions.

• Never use with a child able to climb over or

dislodge/open the gate or enclosure.

• Never use if gate is less than 3/4 of child’s height.

• Do not use if any part of the gate is broken or missing.

This gate is designed for children from 6 months to 24 months. Since each child’s skills develop at different ages, these parameters should be monitored against your child’s own development.

When installed as instructed, between two clean structurally sound surfaces, this gate conforms to:

ASTM F-1004-07 United States Standards

• This product will not necessarily prevent all accidents. Never leave child unattended.

• Use only spare parts available from KidCo.

• Never allow child to climb or swing on gate.

• Use only with the locking/latching mechanism

securely engaged.

• Never use gate at top of stairs.

• Discontinue use if any part of gate is damaged.

• Never climb over the gate.

• Never hang or tie toys etc. to any part of the gate.

Product Information

• No part of gate requires lubrication.

• Clean using warm, soapy water or a damp cloth.

• Do not use abrasive cleaners or bleach.

• If using outdoors, and to help prevent rust, treat gate

with a rust inhibitor. Some rusting may still occur.

• Once installed the gate should be checked

periodically to ensure a safe and secure fit and to maintain proper working order.

Extension Placement Guide

Extension Placement Guide for Premier Gateway Model G150 Note: Each G5.5 Kit contains two extensions Note: Each G12.5 Kit contains one extension

Width Opening Extensions What You Need Placement

29” – 31 ½” Basic Gate No extensions 31 ½” - 34 ½” Included with Gate Gate + 1 extension -on one end 34 ½” – 37” Gate + 2 extensions -1 on each end

37” – 40” 1 G5.5 Kit Gate + 3 extensions -2 on one end; 1 on other end 40” – 42 ½” Gate + 4 extensions -3 on one end; 1 on other end

42 ½” – 45” 2 G5.5 Kits Gate + 5 extensions -3 on one end; 2 on other end 45” – 47 ½” Gate + 6 extensions -3 on each end

47 ½” – 49 ½” 1 G12.5 Gate + 3 extensions -G12.5 on either end; 1 extension on each end

49 ½” – 52” 1 G12.5 + 1 G5.5 Kit Gate + 4 extensions - 1 G12.5 + 2 extensions on one end;

52” – 55” Gate + 5 extensions - 1 G12.5 + 2 extensions on one end;

55” – 57” 2 G12.5 Gate + 2 extensions -1 G12.5 on each end 57” – 60” Gate + 3 extensions -1 G12.5 on each end; 1 extension on one end 60” – 62” Gate + 4 extensions -1 G12.5 + 1 extension on each end

62” – 65” 2 G12.5 + 1 G5.5 Kit Gate + 5 extensions - 1 G12.5 + 1 extension on each end;

65” – 68” Gate + 6 extensions -1 G12.5 + 2 extensions on each end

68” – 70” 2 G12.5 + 2 G5.5 Kits Gate + 7 extensions -

70” – 73 ½” Gate + 8 extensions -1 G12.5 + 3 extensions on each end

Each end may have no more than 4 extensions. Extensions must be added as shown.

1 extension on other end

2 extensions on other end

1 exten

sion on one end

1 G12.5 + 2 extensions on each end;

1 extension on other end

Installation

For further clarification, please see back of user guide for corresponding drawings.

1. The gate must be installed in a structurally sound

opening. Never install between two railings or two stair

posts. Ensure mounting surface (wall, doorframe, stair post, etc.) is strong, rigid and is smooth, clean and grease free.

If mounting onto brick, drywall or other surfaces, an optional gate installation kit, wooden board mounted to the surface or additional hardware may be necessary to provide a solid, smooth surface.

Measure opening to determine if extensions are needed. Correct width will be reached by adjusting all 4 corner spindles. Each spindle adjusts individually and may be extended to varying lengths (up to 1¾” each) to allow for molding, uneven walls, etc.

If using gate on a stairway, it must be placed on the lowest stair on bottom.

2. Spindle attachment is different when using extensions and when not using extensions.

If no extension/s are used, slide top spindles (b) and bottom spindles (s) into spindle housing end with out tab (c). Push assembly into gate corners.

3. If using extension/s, (see Extension Placement

Guide) insert square extension tubes (j) into gate ends.

Connect the bar (k) to one upper extension housing (h) and one lower extension housing (i). Push assembly over extension tubes. There should be no metal showing from extension tubes. It may be necessary to apply pressure to tubes to ensure they are fully inserted into gate ends. Slide top spindles (b) and bottom spindles (s) into extension tubes.

4. Note: Spindle housings are not used if square extension tubes are necessary. If the housings have been inserted, remove with a screwdriver.

5. Center the gate in opening with bottom rail resting

on floor. Gaps on each side should be equal. Open the handle to the raised position by pressing the

buttons (r) and lifting the handle (n) at the same time.

BUTTONS MUST ALWAYS BE PRESSED IN WHEN LIFTING HANDLE. FAILURE TO DO SO WILL RESULT IN HANDLE MECHANISM BREAKING.

Installation

6. Pull out the two bottom spindles (s) until they touch

mounting surface and rest on top of floor molding (if applicable). Tighten handwheels TOWARD GATE FRAME as tightly as possible. Each spindle adjusts individually and may be extended to varying lengths to allow for molding, uneven walls, etc.

IMPORTANT: If gate is properly tightened the yellow and red pressure indicators will be absent (6a). If the

RED pressure indicator is present further tightening is

required (6b). If yellow is still present, gate installation is acceptable but additional tightening is encouraged (6c).

7. Close walk through door so locator (l) is aligned

directly above bottom gate rail. Do not lower handle.

Pull out the top spindle (b) on the hinge side (m) until it touches the mounting surface. Tighten handwheel TOWARD GATE FRAME until locator drops and rests on bottom gate rail.

Operation

10. To Open Gate.

Release locking mechanism by pressing buttons (r)

in while lifting handle. BUTTONS MUST ALWAYS BE PRESSED IN WHEN LIFTING HANDLE. Lift walk

through door so hinge is raised and door will swing open in either direction.

To Close Gate.

Lift walk through door. Position locator (l) until it is above the bottom rail. Make sure hinge has dropped down. Push handle down to lock.

Gate should always be in locked position when in use.

8. Pull out spindle (b) in the handle side until it touches

mounting surface and tighten handwheel TOWARD GATE FRAME so the distance between pressure plate

(o) and pressure hinge (area A) is sufficient for walk through door to open in either direction.

9. IMPORTANT: There is a pressure indicator on the

handle. If gate is properly tightened yellow and red

indicators will be absent (9a). If RED is present further

tightening is required (9b). If yellow is still present, gate installation is acceptable but additional tightening is encouraged (9c).

11. Installation aid

KidCo has available OPTIONAL Y spindles (Model GY-1)

to assist in installation when the mounting surface has a round baluster. These spindles are used in place of the spindles included with the basic gate. They may be ordered through your local KidCo dealer or direct from KidCo.

No more than 2 Y spindles may be used per gate and both must be used on the same side.

Warranty

Your KidCo product is warranted to be free from manufacturing defects for a period of one year from date of

purchase under normal non commercial use and in compliance with the operating instructions. This warranty extends only to the original retail purchaser and is only valid when supplied with proof of purchase.

KidCo will either repair, or at our option replace, free of charge, any parts necessary to correct defects in material or workmanship during the warranty period. This warranty is complete and exclusive. The warranty expressly disclaims liability for incidental, special and consequential damages of any nature. Any implied warranty arising by operation of law shall be limited in operation to the terms of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Should a repair be needed during the warranty period, ship the gate in the original carton or similar protective container (check any retail store or purchase from UPS) and send freight prepaid (we suggest UPS) to:

KidCo, Inc., 1013 Technology Way, Libertyville, IL 60048-5349.

Include a note with your return address, day-time telephone number, and specify what is wrong with the product. Repairs can normally be made within 48 hours after receipt at KidCo. For additional information CALL our customer service department at (800) 553-5529.

KIDCO LIMITED WARRANTY

SHOULD REPAIR OR PARTS BE NECESSARY

Remarques importantes

FRE

LIRE ATTENTIVEMENT CES INSTRUCTIONS ET LES CONSERVER POUR POUVOIR S’Y RÉFÉRER ULTÉRIEUREMENT.

ATTENTION

• Utilisation prévue: enfants âgés de 6 à 24 mois.

• Vérifier la stabilité de la barrière et resserrer

régulièrement toute la quincaillerie et les supports.

• Pour écarter tout risque de blessure grave, voire

mortelle, installer solidement la barrière ou la fermeture et utiliser conformément aux instructions du fabricant.

• Ne jamais utiliser pour un enfant capable de

grimper par-dessus la barrière ou la fermeture ou de la retirer.

• Ne jamais utiliser si la barrière ne mesure pas au

moins les trois quarts de la taille de l’enfant.

• Ne pas utiliser si une pièce de la barrière est cassée

ou manquante.

Cette barrière a été conçue pour les enfants âgés de 6 à 24 mois. Cependant, chaque enfant ayant un rythme de croissance qui lui est propre, ces paramètres doivent être adaptés en fonction du développement de l’enfant.

Quand elle est installée selon les instructions entre deux surfaces propres et solidement charpentées, la barrière est conforme aux normes suivantes :

ASTM F-1004-07 United States Standards

• Ce produit n’empêchera pas nécessairement tous les accidents. Ne jamais laisser un enfant sans

surveillance.

• Utiliser uniquement des pièces détachées KidCo.

• Ne jamais laisser un enfant grimper sur la barrière ni

la secouer.

• Utiliser uniquement avec le mécanisme de

verrouillage/blocage solidement enclenché.

• Ne jamais utiliser la barrière en haut d’un escalier.

• Cesser l’utilisation si un composant quelconque de

la barrière est endommagé.

• Ne jamais grimper sur la barrière.

• Ne jamais suspendre ni attacher de jouets, etc. sur

une partie quelconque de la barrière.

Informations sur le produit

• Aucune partie de la barrière n’exige de lubrification.

• Nettoyer à l’aide d’une éponge avec de l’eau

chaude et un détergent doux.

• Ne pas utiliser de nettoyants abrasifs ou un agent

blanchissant.

• Dans le cas d’une utilisation extérieure et pour

empêcher la formation de rouille, traiter la barrière avec un antirouille. L’apparition de rouille est toujours possible.

• Une fois installée, la barrière doit être

périodiquement vérifiée pour s'assurer de son ajustement sûr et de son bon fonctionnement.

+ 15 hidden pages