Page 1
QS
QSCOMPONENTSYSTEM
QS65.2
QS60.2
English Version
Versión Español
Sistema de altavoces componentes QS
Manual del Propietario
Deutsche Version
QS-Komponentensystem
Benutzerhandbuch
Version Française
Système à composants QS
Manuel d’utilisation
Page 2
QSCOMPONENTSYSTEMOwner’sManual
MODEL: QS65.2 / QS60.2
Authorized KICKER Dealer:
Purchase Date:
Speaker Model Number:
QS COMPONENTS
The KICKER QS-series component systems offer unmatched audio fi delity for vehicle applications.
Whether you’re confi guring the ultimate multi-speaker and subwoofer surround system or simply
upgrading from dull, lifeless factory speakers, the QS component systems deliver the most pleasing fullrange sound on the market today!
PERFORMANCE
Model:
Woofer Size 6” (160mm) 6.5” (165mm)
Tweeter Size 1-3/16” (30mm) 1-3/16” (30mm)
Dome Material Tetoron
Impedance, (DC Resistance) 4:, (3.5:)4:, (3.5:)
Power Handling Peak, (RMS) 180W, (90W) 200W, (100W)
Sensitivity @ 1W, 1m 86dB 87dB
Effective Frequency Range 50Hz–22kHz 40Hz–22kHz
Woofer Mounting Hole Diameter 5-1/16” (129mm) 5-7/16” (138mm)
Woofer Mounting Depth d 2.5” (63.5mm) d 2.5” (63.5mm)
Tweeter Hole Diameter 1-13/16” (46mm) 1-13/16” (46mm)
Flush-mount Tweeter Depth 1-1/8” (29mm) 1-1/8” (29mm)
Crossover High Pass Filter 24dB/octave @ 2.8kHz 24dB/octave @ 2.8kHz
Crossover Low Pass Filter 12dB/octave @ 2.8kHz 12dB/octave @ 2.8kHz
High Frequency Output Level 0dB, +3dB, +6dB 0dB, +3dB, +6dB
QS60.2 QS65.2
®
Tetoron
®
Pro Tip: Looking for the next step in audio performance from your QS components? Upgrade to a
KICKER IX or ZX 4-channel amplifi er for each QS component system you have installed to take full
advantage of the QS’s bi-amping capabilities. With a dedicated amplifi er channel for each tweeter and
each midrange driver, you’ll have a more effi cient system that will deliver a clearer soundstage and
an increasingly dramatic dynamic response. In other words, your music will be more expansive and
captivating.
2
QSCOMPONENTSYSTEM
Page 3
CONFIGURATION
Before mounting and wiring the QS component system, determine which confi guration you will use for the
speakers and crossover.
QS Speaker
Confi gurations
Coaxial great for space-limited applications
Separates optimal sound quality and improved
QS Crossover
Confi gurations
Conventional 2-way easy install | ideal when available
Bi-amplifi ed optimal sound quality; more effi cient
ADVANTAGES CONSIDERATIONS
or when separate tweeter mounting
is not possible
sonic imaging (with proper tweeter
mounting)
ADVANTAGES CONSIDERATIONS
amplifi er channels are limited
usage of amplifer power
high frequencies may not be as
prominent | tweeter output may
need to be increased at crossover
trickier install | vehicle must have a
good tweeter mounting location
audio fi delity not quite as high as
bi-amplifi ed confi guration
requires at least 4 amplifi er
channels | slightly trickier install
tweeter
Coaxial Confi guration
Separates Confi guration
SPEAKER CONFIGURATION
The QS component system comes packaged in a separates confi guration.
To use a coaxial confi guration, see Fig. 1 and follow these steps:
Unscrew and remove the aluminum phase plug from the center of the woofer.1.
Screw the coaxial mounting adapter into the woofer in place of the phase plug.2.
Screw the tweeter into the tweeter post.3.
Thread the tweeter’s lead wires through the center of the woofer.4.
Snap the tweeter post onto the coaxial mounting adapter.5.
Rotate the tweeter clockwise for the most appealing position.6.
Secure the tweeter’s lead wires using the clip on the underside of the woofer.7.
tweeter
phase plug
3
Page 4
Fig. 1
Confi guring the QS for
Coaxial Operation
coaxial mounting adapter
Step 1
Steps 2–6
tweeter lead
wires
QS crossover
INPUT jumper.
Install only for 2-way confi gurations;
do not install if bi-amping.
Fig. 2
tweeter post
Step 7
tweeter
tweeter output-level jumpers.
One of these jumpers MUST be installed. Higher
numbers mean more volume from the tweeter.
+3 dB
0 dB
CROSSOVER CONFIGURATION
The KICKER QS crossover can be confi gured as a conventional 2-way crossover by installing the
included INPUT jumper into the - MID + -TW + input terminals as shown in Fig. 2. In this confi guration,
the amplifi ed signal from your source unit or amplifi er should be wired to the + and - terminals indicated on
the INPUT jumper.
The QS crossover can also be confi gured for bi-amp wiring by removing (or simply not installing) the
INPUT jumper. To use the bi-amp confi guration, you must connect two amplifi ed signals to each
crossover (you will need at least four amplifi er channels). Install one of the included tweeter outputlevel jumpers (0 dB, +3 dB, or +6 dB) to adjust the tweeter output level. Installing jumpers with higher
numbers will result in more volume from the tweeter.
4
QSCOMPONENTSYSTEM
Page 5
WIRING
We recommend using 16 gauge (or larger) wire. The QS components are rated at 4 ohms and work
with any source unit or amplifi er designed to operate at a 4 ohm load. Make sure your source unit or
amplifi er is rated for 4 ohm operation.
Crossover in 2-way confi guration | One component set per channel
At least two amplifi er channels are needed for stereo operation (only one channel is shown)•
crossover
woofer
source unit / amplifi er
+
+
-
OUT
-MID+
- IN +
-OUT+
OUT
-TW+
-
tweeter
Crossover in 2-way confi guration | Two component sets per channel
Requires two complete QS systems (four woofers, four tweeters, four crossovers)•
At least two amplifi er channels are needed for stereo operation (only one channel is shown)•
Crossovers wired in series•
+
-
OUT
- IN +
-MID+
source unit / amplifi er
OUT
-TW+
+
+
-
+
-
OUT
-MID+
- IN +
- OUT +
OUT
-TW+
-
5
Page 6
Crossover in bi-amp confi guration
Two channels per component set
At least four amplifi er channels are needed •
for stereo operation (only two channels are
shown)
+
-
+
-
-
OUT
MID
+
IN
-MID+IN-TW+
-MID+
CH2
LEFT OUTPUT
OUT
TW
-TW+
CH1
+
-
amplifi er / source unit
(must have at least four channels)
Crossover in bi-amp confi guration | One channel per component set
Requires two complete QS systems (four woofers, four tweeters, four crossovers)•
At least four amplifi er channels are needed for stereo operation (only two channels are shown)•
Crossovers wired in series•
+
-
-
OUT
MID
+
IN
-MID+
amplifi er / source unit
(must have at least four channels)
OUT
TW
IN
-TW+
+
-
+
+
-
+
-
-
OUT
MID
+
IN
-MID+IN-TW+
-MID+
CH2
LEFT OUTPUT
OUT
TW
-TW+
CH1
+
-
-
6
QSCOMPONENTSYSTEM
Page 7
WOOFER MOUNTING
The KICKER QS components are designed for free-air applications and do not require a sealed enclosure
for optimum performance. It is important to isolate the sound coming from the front of the speaker from
the sound radiating from the back of the speaker. This is most easily accomplished by mounting the
speakers in a vehicle’s factory locations or in a location with a semi-isolated rear chamber (like the rear
deck of a car behind the rear seats).
If you are replacing factory speakers in their original locations, you may have to enlarge the speaker
cut-outs and pre-drill new screw holes using a 7/64” (2.5mm) bit. Custom mounting locations will require
more preparation and work. Make sure that the speaker will not interfere with trunk and door opening and
closing mechanisms and that the enclosed screws will not puncture the fuel tank, puncture wiring, or
interfere with any other mechanical parts on the underside of the mounting surface. Cycle the windows all
the way down and up.
If the speaker cut-out locations require you to cut metal, avoid structural metal and braces. If the door
body and panel cannot support the weight of the speaker, an optional reinforcing ring (thin piece of wood
or Medium Density Fiberboard) may be fastened or adhered to the door body. Mount the speaker to the
vehicle as outlined in Fig. 3.
door body
reinforcing ring (optional)
door panel
speaker cut-out
QS woofer
Fig. 3
screws
speaker grille
7
Page 8
panel
mounting nut
fl ush ring
Fig. 4
Flush Mounting the Tweeter
panel
mounting nut
back angle ring
Trim the mounting nut legs at the score
lines to accommodate thicker panels.
tweeter
tweeter
front angle ring
inset surface
rounded surface
Fig. 5
Angle Mounting the Tweeter
TWEETER MOUNTING
The tweeter can be mounted one of three ways: fl ush, angled, and coaxial mounting. For fl ush mounting
applications, see Fig. 4. Choose a fl at location on the panel with space behind the panel to allow room
for the mounting nut, motor structure, and tweeter post. After checking the clearances, cut a 1-13/16”
(46mm) diameter mounting hole in the panel. Position the mounting nut behind the panel. Feed the
wire through the optional fl ush ring, the hole in the panel, and the mounting nut. Mount the tweeter by
screwing the mounting nut onto the tweeter.
For angled mounting applications choose a fl at location on the panel with space behind the panel to
allow room for the mounting nut, motor structure, tweeter post, and back angle ring. After checking the
clearances, cut a 1-13/16” (46mm) diameter mounting hole in the panel. Place the front angle ring in front
of the panel. Then place the wire and tweeter through the front angle ring and into the panel. Next, place
the wire through the back angle ring, place the back angle ring over the rear of the tweeter, and line-up
the narrow part of the front angle ring for the preferred angle of operation. Place the wire through the
mounting nut and loosely tighten the mounting nut around the tweeter. Rotate all the parts in unison until
the tweeter is angled in the desired direction. Secure the assembly by tightening the mounting nut. See
Fig. 5.
8
QSCOMPONENTSYSTEM
Page 9
CROSSOVER MOUNTING
Mount the crossover in a location that is easy to access for wiring and tweeter output level adjustment.
Make sure that the crossover will not be exposed to water. The bottom of the car door is not a good
location. If you must mount the crossover in the car door, exercise caution as water can accumulate in the
bottom of the door. Keep the crossover high in the door and shielded from water.
QS crossover.
(mounted inside
door panel)
tweeter mounting hole
to tweeter
lead wires
door jamb
woofer mounting hole
If factory speaker wiring is not available in your desired location, it may be necessary to run speaker wire
through the door jamb. The speaker wire should be kept away from sharp edges and avoid the possibility
of getting pinched by the door. An existing grommet in the door jamb is the ideal place to run the speaker
wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole to run the
speaker wire through the door jamb. Be careful not to drill into other wiring or existing door mechanisms.
Any time a wire is run through a hole, it is necessary to insert a rubber or plastic grommet to protect the
wire from damage.
to woofer
terminals
rubber
grommets
from amplifi er or
source unit
9
Page 10
GRILLE MOUNTING
10
QSCOMPONENTSYSTEM
Page 11
ACOUSTICS LIMITED WARRANTY
KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it
is warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases you must have the original receipt.
Should service be necessary under this warranty for any reason due to manufacturing defect or
malfunction during the warranty period, KICKER will repair or replace (at its discretion) the defective merchandise
with equivalent merchandise at no charge. Warranty replacements may have cosmetic scratches and blemishes.
Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original
purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied
warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the
original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty
gives you specifi c legal rights; however you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly. You can confi rm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package only
the defective items in a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing the Customer’s
name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof-ofpurchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifi er clipping or distortion
o Items previously repaired or modifi ed by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products returned without a Return Merchandise Authorization (RMA) number
o Freight Damage
o The cost of shipping product to KICKER
o Service performed by anyone other than KICKER
stillwaterdesigns
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of 48-hour service for all acoustics (subwoofers, midrange drivers, tweeters,
crossovers, etc) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to
follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department
at (405) 624-8510. Contact your International KICKER dealer or distributor concerning specifi c procedures for your
country’s warranty policies.
Note: All specifi cations and performance fi gures are subject to change. Please visit www.kicker.com for the
most current information. To get the best performance from your new KICKER speakers, we recommend using
genuine KICKER accessories and wiring. Please allow two weeks of break-in time for the speakers to reach optimum
performance.
P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510
20081107+G-09QS
11
Page 12
©2008 Stillwater Designs
Loading...