Kicker KMTC65, KMTDC65, KMTC8 Owner's Manual
KMTC
Loaded Marine Cans
Owner's
Manual
{fKICKER.
KICKER
Owner's
LOADED
Manual
MARINE
CANS
MODEL:
Authorized
Purchase Date:
Serial Number:
The KICKER KMTC Loaded Marine Cans are the perfect way
power sports environment. The KMTC65
speakers. The injection-molded ABS enclosures are
Mount
your
Model: KMTC65 KMTDC65 KMTCB
Rated
Sensitivity
Peak
Continuous
Enclosure
Enclosure
Enclosure
Enclosure
KICKER
the KMTC Loaded Marine Cans
4x4
or
Impedance
Power
Dealer:
Side-by-Side's roll bars,
[OJ
[1W,
1m]
Handling
Power
Oiameter/VVidth
Depth
Height
Height
[Watts]
Handling
[in,
em]
(from
bottom
(bracket
[Watts
[in,
top
RMS]
em]
of
roll
to
enclosure
or
bar)
[in,
KMTC65IKMTDC65IKMTC8
to
bring your music
and
KMTCB
1n
your
boat
in any other bar-mounted application.
em]
bottom)
[in,
come
loaded with the KICKER
UV
treated, splash resistant, and weather resilient.
or
get
creative with a pair
4 4 4
90 93
195
65
7,
17.8
9-11/16, 24.6 9-11/16, 24.6
8-1/4,
21
em]
10·1/4,
26
390 300
130 150
14-1/16,35.7
8-1/4,
101/4,26
out
of
them in the
21
into the marine
KM65
or
and KMB LED
gara@e,
92
8-3/16, 20.8
11-5/16, 28.7
9-7/16,
11
on
24
1/2, 29.2
INSTALLATION
Step
1:
Determine the location and placement
mount1ng. Spreading the KMTC Loaded Marine Cans apart will provide better stereo performance, and is
usually preferable.
obstructions that could complicate mounting the KMTC. Please keep in mind the routing
wires
as
this can affect where you finally
hole
in
the
pipe
of the lower mounting bracket
through; ie the hole should
comng
hole directly in the bottom
from the lower mount1ng bracket. If the speakers will
When
determining the
5/8"
(16mm) in diameter. The placement of the hole must line
so
that the wiring com1ng from the lower mounting bracket can
be
90°
from the direction the speakers will
of
the tube.
/
of
the KMTC
best
locations for mounting,
mount
your cans. You will need
cans
onto the
be
level with the horizon, you should drill a
pipe
or
tube
to
which you are
be
careful
to
be
to
look for obstacles
of
mark
and drill a wire routing
up
w1th
the final position
aimed and in line with the
your speaker
be
or
run
w1ring
2
Thread the speaker and LED wires through the bottom
2:
Step
plastic liner hole
the
the center.
1n
lower mounting bracket
t
of
the
mounting bracket and out
lower
of
layer
must apply a
IMPORTANT:
before
3: The mounting hardware design provides
Step
output
place, install the
engages with the groove in the swivel
You
installation.
the ideal
to
listen1ng
swivel clamp
thin
position using the quick adjust
and tightly
the tncluded anti-seize compound to
of
angular
versatility
secure it using the
base.
lower mounting bracket
in
swivel lever. With the
included swivel bolt, making sure the
posit1on1ng
sw1vel
threaded
ALL
direct the speaker's
to
lower mounting bracket in
clamp
fasteners
clamp
swivel bolt
3
Loading...