Kicker KMC2 Owner's Manual

Owner’s Manual | English

Manual del Propietario | Español
KMC2 Receptor Multi-Media

Benutzerhandbuch | Deutsch
KMC2 Multi-Media-Receiver

Manuel d’utilisation | Française
KMC2 Multi-Media Receiver

KMC2

Multi-Media Receiver

KMC2

1

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

FCC Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC Notice - CAN ICES-3 (B) - This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Avis d’Industrie Canada - Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est au-
torisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement. mauvais fonctionnement de I’appareil.

Cet appareil numériquie de la classe B est conforme à la norme NMB-003 du Canada. CAN NMB-3 (B)

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf, utilisateurs peut
obtenir l’information canadienne sur l’exposition et la conformité de rf.

FCC ID: RGR-KMC2 IC ID: 11078A-KMC2

2

mounting hole cutout template:
3-5/8 inches, 92.1 mm

gabarit de montage trou découpé:
3-5/8 pouces, 92,1 mm

plantilla de recorte del agujero de montaje:
3-5/8 pulgadas, 92.1 mm

montageloch ausschnittschablone :
3-5/8 Zoll, 92,1 mm

3

mounting hole cutout template:
3-5/8 inches, 92.1 mm

gabarit de montage trou découpé:
3-5/8 pouces, 92,1 mm

plantilla de recorte del agujero de montaje:
3-5/8 pulgadas, 92.1 mm

montageloch ausschnittschablone :
3-5/8 Zoll, 92,1 mm

4

KMC2 OWNER’S MANUAL

Contents

Specs 5
Overview 6
Installation 7
Operation 9
Troubleshooting 10
Warranty 29

Contentido

Especifi caciones 11
Descripción general 12
Instalación 13
Funcionamiento 15
Resolución de problemas 16
Garantía 29

Contentu

Spécifi cations 23
Généralités 24
Installation 25
Utilisation 27
Dépannage 28
Garantie 29

Inhalt

Technische Daten 17
Übersicht 18
Installation 19
Betrieb 21
Fehlersuche 22
Garantie 29

5

Model KMC2
Power Output @ 14.4V, 4Ω stereo, <10% THD+N 25W x 4
Frequency Response [Hz] 20 – 20k
Signal-to-Noise Ratio [dB] 95
Input Sensitivity 500mV
USB Playback MP3
USB Charging DC 5V, 1A
USB Compatible File System FAT32
Line-Out Level [V] 4
Outer Trim Ring Diameter [in, cm] 4-1/2, 11.3
Protrusion From Mounting Surface [in, cm] 1-1/8, 2.75
Total Mounting Depth [in, cm] 4, 10.1
Mounting Panel Thickness Range [in, cm] 1/4-2, .6-5

Be careful not to drill into wiring or vehicle mechanisms.
You are solely responsible for securely mounting the KMC2
Media Center. See page 2–3 for mounting hole cutout
template.

Before installation, you may wish to plan your placement
of the USB and Auxiliary inputs, and the optional PXiRCX
remote (sold separately), for both convenience and looks!

With a KICKER KXM amplifi er, a pair of KICKER KM
speakers, and a few KICKER cables, you’re looking at a full
system upgrade that will dominate! KICKER amplifi ers and
accessories make upgrading a snap. Ask your dealer about
KICKER amplifi ers and speaker upgrades to complete your
system!

All specifi cations and performance fi gures are subject
to change. Please visit www.kicker.com for the most
current information.

WARNING: KICKER products are capable of producing sound levels
that can permanently damage your hearing! Turning up a system to a level
that has audible distortion is more damaging to your ears than listening to
an undistorted system at the same volume level. The threshold of pain is
always an indicator that the sound level is too loud and may permanently
damage your hearing. Please use common sense when controlling
volume.

Authorized KICKER Dealer:
Purchase Date:
Serial Number:

SPECIFICATIONS

6

•change tuner band

•rotate display category

Automatic Preset Scan
in radio mode: •seek next station

•program strongest stations
in usb mode: •change repeat modes

•manually select track number
in Bluetooth

®

mode: •disconnect bluetooth device

•decrease volume

•decrease value

•increase volume

•increase value

•change input source

•enter settings menu

•digital display

•previous track/rewind

•change preset/change tuner

•next track/fast forward

•change preset/change tuner

•mute/unmute

•power on/off

•play/pause

•save station to current preset

NOTE: use short and long presses to operate
some input sources do not support all functions

OVERVIEW

7

12V

USB input
USB charging

front RCA out

+12V (battery)

≤7”

18cm

+12V (ignition)

rear
right

rear
left

front
right

front
left

rear RCA out

AUX input

radio antenna

ground

fuse

battery

ground

remote auto-turn on output

PXiRCX wired remote
(sold separately)

positive
negative

INSTALLATION

8

3. Place washers over bolts and securely attach nuts.

4. Depending on the size of your mounting baffl e, you may need to snap off one or more of the metal tabs from the mounting bracket to

accomodate installation.

1.2.3.

4.

4.

1.

Attach threaded bolts to the back of the KMC2

2. Position the mounting bracket over the bolts.

9

BEEP - select whether the KMC2 responds with beeps

EQ - select between EQ presets:
Flat, Classical, Pop, Rock, and Off

LOUD - select On or Off for a low frequency boost

AREA - select North America or Europe.

P-VOLUME - select the default volume level for the KMC2

OPERATION

Playback

Use the MODE button to choose the input source for the KMC2:
Bluetooth, USB, AUX, and TUNER.

The KMC2 will automatically enter Bluetooth pairing mode when there
is no Bluetooth connection, with the display message “BT MUSIC”.
When you begin scanning for devices on your audio device, the
KMC2 will identify as “Media Center”.

The USB input source is only available when there is a USB device
connected. The KMC2 will automatically switch to USB input when
a USB device is connected and detected. KICKER recommends
SANDISK drives for the best performance. In testing, the KMC2 has
been shown to work with some HDD’s, however, this is not supported
by KICKER! Drives must be formatted in FAT16 or FAT32 fi le systems.

Use the BND button to cycle through the 5 available radio tuner
bands: FM1, FM2, FM3, AM1 and AM2.

Settings

Press & Hold the MODE button to enter the settings menu. The
available settings are: Bass, Treble, Balance, Fader, Beep, EQ, Loud,
Area, and Preset Volume. Use the VOL - & VOL + buttons to change
the available values for each setting.