Keurig Ultra Owner's Manual

WARNING
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT REMOVE
THE BOTTOM COVER. NO USER
SERVICEABLE PARTS ARE INSIDE. REPAIR
SHOULD BE DONE BY AUTHORIZED
SERVICE PERSONNEL ONLY.
DO NOT OPEN
3
KEURIG®GOURMET SINGLE CUP HOME BREWING SYSTEM
Model B50 Use & Care Guide
TABLE OF CONTENTS
SECTION 1
SET-UP & OPERATION
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Set-Up & First Brew . . . . . . . . . . . . . . . . . . 6
SECTION 2
CONTROLS & INDICATORS
LCD Control Center . . . . . . . . . . . . . . . . . . . 9
SECTION 3
CLEANING & MAINTENANCE
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
De-Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SECTION 4
TROUBLESHOOTING . . . . . . . . . . . . . . . . . 13
SECTION 5
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pour des directives en Français, veuillez vous reporter à la page 15.
CAUTION: There are two sharp needles that puncture the K-Cup
®
portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder.
T
o avoid risk of injury, do not put your
fingers in the K-Cup Chamber.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process.
T
o avoid risk of injury, do not lift the Handle or open the K-Cup Chamber during the brew process.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or table­top where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
Record your Brewer Serial Number here. The Serial Number is located on the bottom of the Brewer on a white sticker.
_________________________________
5
Features
Water Reservoir Lid
Water Reservoir
Water Reservoir Lock Tab Slots
Handle
K-Cup
®
Portion Pack Holder (E and F are
the K-Cup Holder Assembly)
Funnel
Lid
K-Cup
®
Portion Pack Assembly Housing
Housing
Drip Tray Plate
Drip Tray
Drip Tray Base
Vent
Power Cord
A
B
C
D
E
F
G
Small Cup/Hour Button
Menu Button
Large Cup/Minute Button
LCD Control Center
Power Button
O
P
Q
R
S
O
P
Q
R
S
H
Model B50 Brewer
Controls and Indicators
I
J
K
L
M
N
4
1. Keep your Brewer turned ‘ON’ at all times.
To brew a fresh cup of coffee or tea anytime you want, we suggest you keep your Brewer turned ‘ON’ all the time.
However, the Brewer is fully programmable so you can set it to turn on and off automatically to match your schedule. Or, if you prefer, set the Brewer to automatically turn off after a period of time.
Follow the simple instructions on page 9 to make using the Brewer convenient for you.
2. For the best tasting gourmet coffee or tea, Keurig recommends using bottled or filtered water.
Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee such as chlorine or other mineral taste, we recommend you consider using bottled water or water from a filtration system.
3. Choose from two serving sizes.
The perfect cup of coffee means something different to each coffee lover. With its wide variety of coffees to choose from and the ability to brew a regular large cup (7.25 oz serving) or stronger small cup (5.25 oz serving), the Brewer lets you enjoy your own personal cup brewed to perfection. Follow the simple instructions on page 7.
4. Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other appliances, your Brewer may not function properly. The Brewer should be operated on its own circuit, separate from other appliances.
5. Brewing into a travel mug.
To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base.
1. Place Brewer box on a large steady surface (such as a table or countertop) or on the floor. Open the box.
2. Remove the Quick Start Guide, Use & Care Guide and other literature.
3. Remove the package of complimentary K-Cup
®
portion packs.
4. Turn the box on its side with front of box face down.
5. Reach into the box and grasp the plastic bag that contains the Brewer.
6. Carefully pull the plastic bag (and packaging materials) toward you and out of the box. The Brewer will still be encased in the polyfoam and be on its side.
7. Remove the top polyfoam packaging material.
8. Carefully lift Brewer off of the bottom polyfoam and place it upright on a flat, steady surface.
9. Lift plastic bag off of Brewer.
10. Carefully turn the Brewer on its side and record on page 3 of this book the Serial Number located on the white sticker on the bottom of the Brewer. The Serial Number is also located on the bottom of the Brewer box.
11. Place the Brewer upright on a flat, steady surface. Remove tape holding Water Reservoir in place.
We recommend you save all packing materials in case future shipping of the product is necessary.
SET-UP & OPERATION
Helpful Hints
SECTION 1
WARNING: Keep all plastic bags away
from children.
Unpacking Instructions
A
B
D
E
F
C
J
K
G
L
M
N
I
H
Set-Up & First Brew
IMPORTANT: You cannot use your Keurig
brewer until it has been primed for its first use as set forth below.
Priming your Brewer
1. Unwrap cord and plug the brewer into a grounded outlet.
2. Place a cup or mug on the Drip Tray Plate.
3. Remove the Water Reservoir from Brewer by first removing Lid from Reservoir, then lifting Reservoir straight up and away from Brewer (may be tight). Rinse with fresh water.
4. Fill Water Reservoir with fresh water so that the water level reaches the top edge of the clear viewing area. (Be careful not to over fill.)
5. Place Water Reservoir base into the left side of the Brewer and be sure the Water Reservoir Lock Tabs engage with the Brewer. Replace Lid on Water Reservoir.
6. Press Power Button found on upper right panel of the Brewer. The green light surround­ing the Power Button will become illuminated.
7. The LCD Control Center will come on and indicate ‘PRIME’ and the icon for the Large Cup will flash. If 'NOT READY' appears in
LCD Control Center, be sure the handle is all the way down. Please note, a K-Cup should not be used for the Priming Sequence.
8. Press the Large Cup Button below the flashing Large Cup indicator.
9. The Brewer will automatically fill the Brewer (priming it) and then the water will be heated. This will take about 3 minutes. During the heating period 'NOT READY' is dis­played on the LCD Control Center. When the water is heated, 'READY' will be displayed.
10.Press the Large Cup Button below the flashing Large Cup Icon to start a cleansing brew, during which hot water will flow into your cup or mug. Pour the hot water into the sink.
11.The Brewer may take 15 seconds to reheat water between brews and then 'READY' will again be displayed.
12. The one-time priming process is now complete and you are ready to brew!
6
7
Ready to Brew your First Cup
1. LCD Control Center will indicate ‘READY’.
2. Place a cup or mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup Holder will open toward you.
4. Select a K-Cup
®
portion pack.
5. Place a K-Cup
®
portion pack in the K-Cup
Holder (as shown in exhibit at top of page).
6. Lower the Handle to close the Lid over the K-Cup Holder, (when it is closed completely
, the LCD Control Center will indicate ‘BREW’ and the large and small cup icons will blink up to 60 seconds).
7. Choose the amount of coffee or tea you wish to brew by pressing the button under the Small Cup or Large Cup Icon that indicates your choice. The Large Cup choice will yield a 7.25 oz serving and
the Small Cup choice will yield a
5.25 oz serving.
8. The LCD will now display the word ‘BREWING’ and the serving size you selected.
9. There may be a short pause before the brewing process begins. The process lasts for approximately 40 seconds and ends with a burst of air to remove all liquid coffee or tea from the K-Cup.
10. Lift the Handle and remove and dispose
of the used K-Cup.
CAUTION: K-Cup will be hot.
11. Enjoy your first cup of Keurig Brewed
®
gourmet coffee or tea!
12. Your Brewer may display ‘NOT READY’
as it heats water for the next brew cycle. The ‘READY’ indication will return to the LCD Control Center in approximately 15 seconds.
BREW
NOTE: You may see small amounts of water
coming from the Vent and dripping into the Water Reservoir during this and subsequent heating – this is normal.
NOTE: Do not remove the foil lid or puncture the K-Cup
®
portion pack.
NOTE: If the Water Reservoir is empty or not in place on the Brewer, then the LCD Control Center will also indicate ‘ADD WATER’. None of the buttons will be activated until water is added to the Water Reservoir.
BREWING
Large Cup
Small Cup
Large Cup Button
Large Cup Icon
Power Button
PRIME
CAUTION: There are two sharp needles that puncture the K-Cup
®
portion pack, one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. T
o avoid risk of injury,
do not put your fingers in the K-Cup Chamber.
NOTE: If you do not push the Brew Buttons in 60 seconds, the LCD Control Center will return to ‘READY’ and the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew Buttons by raising and lowering the Handle completely.
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process.
T
o avoid risk of injury, do not lift the Handle or open the K-Cup Chamber during the brew process.
Handle
K-Cup Chamber
NOTE: If Brewer has been exposed to tempera-
tures below freezing, allow Brewer at least two hours to reach room temperature before prim­ing. A frozen or extremely cold brewer will not prime properly and can cause damage.
MENU
NOTE: Following the brew, your Brewer will fill to be ready for the next brew. The pump will make a vibrating sound. This is normal.
K-Cup
®
portion pack
Stopping the Brew Process
If you need to stop the brewing after the process has started, press the Power Button to turn the Brewer ‘OFF’. The flow of coffee or tea will stop, the heating element will shut off and the green light illuminating the Power Button will disappear.
Adding Water
The LCD Control Center of your Brewer will indicate when the water level in the tank is low or if the Water Reservoir has been removed by displaying the words ‘ADD WATER’. The Brewer will not allow you to brew when ‘ADD WATER’ is displayed.
The Water Reservoir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour water directly into the Water Reservoir while it is still attached to the Brewer, then replace the Lid.
2. Remove the Water Reservoir from Brewer
by first removing Lid from Reservoir, then lifting Reservoir straight up and away from Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid.
Brewing Hot Water
Your Brewer is able to produce a cup of hot water for making hot chocolate, for use in cooking, for making soups, etc. Simply raise and lower the handle on the Brewer without adding a K-Cup
®
portion pack. The LCD Control Center will display 'READY' and the Small and Large Cup Icons will blink. Be sure to have a mug or cup on the Drip Tray and then select the size you would like.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge the water from the inner tank.
1. If there is water in the Water Reservoir,
remove the Lid, then lift Reservoir straight up and away from Brewer. Discard water, rinse and refill with water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and
lower the handle on the Brewer without inserting a K-Cup.
3. The LCD Control Center will display ‘READY’
and the Small and Large Cup Icons will blink. Be sure to have a mug on the Drip Tray and then select the larger size brew.
4. Repeat steps 2 and 3 two more times to
completely purge water from inner tank.
If you are experiencing any problems with your Brewer, please contact Customer Service at 1-866-901-BREW (2739).
8
9
ADD WATER
SECTION 2
LCD Control Center
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the LCD Control Center. NOTE: You must set the clock if you will be using the Auto On/Off Time program­ming feature.
a. Press the button below 'MENU'. b. The word 'OFF' will appear at the top of the
LCD Control Center to indicate that the clock is not set. The words 'SET CLOCK', 'SET AUTO OFF' and 'SET ON TIME' will appear in the LCD Control Center with an arrow pointing to 'SET CLOCK'. H (Hour) and M (Minute) will appear and blink.
c. Press or hold the black button under the
blinking H until you have reached the appropriate hour. If the hour has passed 12, the indicator switches from AM to PM on the LCD.
d. Press or hold the black button under the
blinking M to set the minutes.
e. When you have reached the correct time,
press the menu button four times to scroll through the remaining programming options and return to 'READY' mode.
f. The correct time should now be displayed
in the LCD Control Center.
Programing On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee or tea on your own schedule. By programming your Brewer to turn on each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee.
1. Leave it ON all the time (recommended).
The Brewer can be left on all the time so that it is always ready to brew a fresh cup of gourmet coffee or tea. To turn the Brewer off at any time, simply press the Power Button. (Note: Although the clock remains on if set, you can not brew a cup of coffee or tea.) Press the Power Button again to restore power to the Brewer. You will have to wait for the water to heat up before the Brewer is ready to brew.
2. Set the Brewer to turn off at a specified period of time after the last brew.
a. Press the MENU button twice to program
the AUTO OFF feature. The LCD Control Center will now display 'SET AUTO OFF' with a small arrow next to it.
b.Press and release the H Button to
advance 1 hour at a time, up to 9 hours.
c. After setting the desired AUTO-OFF time,
press the MENU button three times to scroll through the remaining program ming options and return to 'READY' mode. 'AUTO OFF' will now be displayed to indicate that it has been set.
CONTROLS & INDICATORS
NOTE: You may get less coffee or tea in
your cup during your next brew. We recommend that you perform a cleansing brew with water only after a terminated brew. Then your NEXT brew will be the volume you have selected.
IMPORTANT: Do not remove the Water Reservoir during the brewing process.
NOT
READY
NOTE: If power is interrupted to the
Brewer by unplugging it, or if power is lost, follow the procedure above to reset the time as the clock will not be visible until the time is set.
OFF
H MENU M
10 :0 0
PM
H MENU
SET CLOCK
ÁSET AUTO OFF
SET ON TIME
Á
SET CLOCK SET AUTO OFF SET ON TIME
Loading...
+ 9 hidden pages