Kettler K-7122-490, K-7122-890, K7162-890, K-7162-490 Instructions Manual
Kettler Stockholm Table Tennis Table Instructions
Models K-7122-490, K-7122-890, K-7162-490, K7162-890
Copyright ©2004 Robbins Specialties
Kettler Stockholm Table Tennis Table Unpacking & Moving Instructions
Models K-7122-500, K-7122-700, K-7162-500, K7162-700
Copyright ©2004 Robbins Specialties
Two people are needed to carry the box,
because of the weight and bulk.
When ready to unpack and to remove the
contents from the carton, turn the carton 90
degrees from its upright position. Open the left
and right ends of the carton. With one person
pushing on the contents from one side, have
another person pull from the opposite side until
contents are removed from the carton.
When carrying the table up or down stairs, it is
advisable to remove the plastic wrap from the
table tops and carry each piece individually to
reduce the weight.
The following pages will provide a breakdown of
the parts contained within the carton.
- 1 -
Kettler Stockholm Table Tennis Table Parts Inventory
Models K-7122-500, K-7122-700, K-7162-500, K7162-700
Copyright ©2004 Robbins Specialties
MASTER CARTON CONTENTS
#PRE-1
TABLE TOP HALVES PREASSEMBLY
4’6” x 5’
2 EACH
USED IN: STEP 13 (2 EA)
Master Carton Size 5’2” x 4’8”
WHEEL PACK
7 ½” x 21”
2 EACH
(SEE PAGE 3 FOR
CONTENTS)
CORRUGATED HARDWARE
ENVELOPE
4’ x 37 ¾”
1 EACH
(SEE PAGE 4 FOR CONTENTS)
CROSS BRACE FOR TABLE END LEGS
USED IN: STEP 12 (2 EA)
NON LOCKING BRACE
USED IN: STEP 10 (2 EA)
- 2 -
#21
49 3/8” x 1 7/8”
2 EACH
#15
38 5/8”
2 EACH
CENTER SUPPORT CROSS BRACES
USED IN: STEP 10 (2 EA)
LOCKING SIDE BRACE PREASSEMBLY
USED IN: STEP 10 (2 EA)
#14
5’
2 EACH
#PRE-4
38 5/8”
2 EACH
WHEEL PACK CONTENTS
(Below is depicted the contents of one wheel pack)
WHEEL FOR NON LOCKING CASTER
USED IN: STEP 3 (4 EA)
#32
LOCKING WHEEL PIVOT
2 EACH
USED IN: STEP 1 (2 EA)
#8
4”
4 EACH
#34
RED WHEEL LOCK
2 EACH
USED IN: STEP 1 (2 EA)
#35
WHEEL FOR LOCKING CASTER
4”
4 EACH
USED IN: STEP 4 (4EA)
#9
NON LOCKING WHEEL PIVOT
2 EACH
USED IN: STEP 2 (2 EA)
CORRUGATED HARDWARE ENVELOPE
Size 4’ x 37 3/4”
CORRUGATED HARDWARE ENVELOPE CONTENTS
CENTER PIVOT PREASSEMBLY
#PRE-3
18 ½” HEIGHT
2 EACH
USED IN: STEP 8 (2 EA)
T-SHAPED CENTER SUPPORT PREASSEMBLY
USED IN: STEP 2 (2 EA)
#PRE-2
24 ¾” x 21 ½”
2 EACH
#17
NET POST
10” HEIGHT
2 EACH
USED IN: STEP 5 (2 EA)
HARDWARE PACK NO. 1
8 ½” x 10”
1 EACH
(SEE PAGE 5 FOR CONTENTS)
- 4 -
HARDWARE PACK NO. 2
(CONTAINS PACKS 2A &2B)
10” x 12 ½”
1 EACH
(SEE PAGE 6 FOR CONTENTS)
#16
CENTER SUPPORT COVER
21 ¾” x 11 ¾”
2 EACH
USED IN: STEP 15 (2 EA)
HARDWARE PACK NO. 3
6” x 11”
1 EACH
(SEE PAGE 9 FOR CONTENTS)
HARDWARE PACK NO. 1 CONTENTS
#22
PLASTIC END INSERT FOR LEG
CROSS BRACE
4 EACH
USED IN: STEP 12 (4 EA)
Size 8 1/2” x 10”
#HDW-12
16 MM WASHERS
24 EACH
USED IN: STEP 2 (8 EA);
STEP 3 (8 EA);
STEP 4 (8 EA)
#HDW-13
25 MM
WASHERS
4 EACH
USED IN:
STEP 2 (4 EA)
#HDW-15
8M BOLT CAP
8 EACH
USED IN:
STEP 2 (4 EA);
STEP 3 (2 EA);
STEP 4 (2 EA)
#HDW-23
M5 NUT
4 EACH
USED IN:
STEP 12 (4 EA)
#HDW-1
M8x125 BOLTS
5 7/8” HEIGHT
4 EACH
USED IN: STEP 2 (4 EA)
- 5 -
#HDW-5
M8x110 BOLTS
5 1/4” HEIGHT
USED IN:
STEP 3 (2 EA);
STEP 4 (2 EA)
4 EACH
#HDW-2
M6x100 BOLTS
4 7/8” HEIGHT
4 EACH
USED IN:
STEP 13 (4 EA)
#HDW-24
STEEL CASTER RODS
4 EACH
USED IN:
STEP 2 (4 EA)
#HDW-19
PINS
2 EACH
USED IN:
STEP 1 (2 EA)
HARDWARE PACK NO. 2 CONTENTS
#HDW-27
ADAPTER FOR NET POST
2 EACH
USED IN: STEP 5 (2 EA)
Size 10” x 12 1/2”
#HDW-29
LOCK END CAPS
2 EACH
USED IN: STEP 11 (2 EA)
HARDWARE PACK NO. 2A
PARTS BAG WITHIN PACK NO. 2
1 EACH
(SEE PAGE 7 FOR CONTENTS)
- 6 -
HARDWARE PACK NO. 2B
PARTS BAG WITHIN PACK NO. 2
(SEE PAGE 8 FOR CONTENTS)
1 EACH
HARDWARE PACK NO. 2A CONTENTS
#HDW-8
M6x49 BOLTS
1 15/16” LENGTH
4 EACH
USED IN: STEP 14 (4 EA)
Size 8 1/2” x 6”
#HDW-7
M6x58 BOLTS
2 1/4” LENGTH
2 EACH
USED IN: STEP 13 (2 EA)
EXTRA PARTS – DO NOT USE
4 5/16” BOLTS
USED IN: NOT USED
#HDW-9
3,9 x 13 SCREWS
1/2” LENGTH
6 EACH
USED IN: STEP 15 (6 EA)
#HDW-11
12,5 MM WASHERS
10 EACH
USED IN: STEP 13 (2 EA);
USED IN: STEP 14 (8 EA)
- 7 -
#HDW-17
M5 NUTS
4 EACH
USED IN: STEP 8 (4 EA)
#HDW-20
BLACK NYLON SPACER
4 EACH
USED IN: STEP 13 (4 EA)
#HDW-16
M6 BOLT CAPS
6 EACH
USED IN: STEP 13 (2 EA);
USED IN: STEP 14 (4 EA)
#HDW-21
BLACK NYLON WASHERS
4 EACH
USED IN: STEP 13 (4 EA)
HARDWARE PACK NO. 2B CONTENTS
#HDW-3
M8x60 BOLTS
2 3/8” LENGTH
6 EACH
USED IN: STEP 9 (2 EA); STEP 11 (4 EA)
Size 7” x 9”
#HDW-6
M5x65 BOLTS
1 15/16” LENGTH
4 EACH
USED IN: STEP 8 (4 EA)
#HDW-4
M6x45 BOLTS
1 3/8” LENGTH
4 EACH
USED IN: STEP 6 (4 EA)
#HDW-13
25MM WASHERS
6 EACH
USED IN: STEP 9 (2 EA); STEP 11 (4 EA)
#HDW-22
3MM SQUARE WASHERS
4 EACH
USED IN: STEP 6 (4 EA)
- 8 -
CROSS BRACE INSERT
USED IN: STEP 9 (2 EA); STEP 11 (4 EA)
# 28
6 EACH
#HDW-10
12MM WASHERS
4 EACH
USED IN: STEP 8 (4 EA)
#HDW-18
M6 NUTS
4 EACH
USED IN: STEP 8 (8 EA)
Size 6” x 11”
HARDWARE PACK NO. 3 CONTENTS
NET ASSEMBLY PARTS
USED IN: STEP 16 (1 EA)
#18
1 EACH
1 EACH PHILLIPS HEAD SCREW DRIVER
1 EACH WRENCH (13, 10, 8MM)
1 EACH WRENCH WITH ROD (10, 13MM)
INCLUDED TOOLS
- 9 -
Loading...