Kettler ADIRONDACK 2511 User Manual
2511 ADIRONDACK BENCH
Contents:
(1) Seat, (1) Back
(2) Arm Rests
(2) Front Chair legs
(2) Back Chair legs
(2) Cross Braces
Tools Required:
#3 Phillips Head Screwdriver
7/16” Wrench
a. Align predrilled holes then insert bolts
1.
to attach front legs.
1a.
(18) 1/4 - 20 x 2” Bolts
(2) 1/4 - 20 x 2 1/2” Bolts
(1) #10 x 3” Screw
(10) Washers
(10) Locknuts
Locknut Washer Bolt
b. Align predrilled
holes then insert bolts
to attach back legs.
1b.
Assembly Instructions
1.
a. With the wing on the post facing front,
align the predrilled holes on front leg to the seat
and insert the 1/4 - 20 x 2” Bolts through the leg
in thru the seat. Clean any plastic residue from
the bolt then slide a washer on. Screw on the
locknut and then tighten it with the wrench and
phillips screwdriver.
2.
Place arm rest
on top of chair
legs, align front
predrilled holes,
insert bolt.
4.
Attach the
braces to
the legs by
aligning holes
and inserting
a 2” bolt.
Attach the back
3.
of the chair by
aligning holes on
the arm and the
seat to insert bolt.
3b.
3a.
Slide washer then
locknut onto end of
bolt then tighten.
b. Align the predrilled holes on the back leg to
the seat and insert the 1/4 - 20 x 2” Bolts through
the leg in thru the seat. Clean any plastic residue
from the bolt then slide a washer on. Screw on the
locknut and then tighten it with the wrench and
phillips screwdriver.
2.
Place arm rest on top of chair legs align the
front predrilled holes and insert the 1/4 - 20 x 2”
Bolts through the leg and in thru the arm. Clean
off any plastic residue then slide a washer on the
end of bolt. Screw on the locknut and then tighten
it with the wrench and phillips screwdriver.
3.
a. Attach the back of the chair to the seat
by aligning holes and inserting a 1/4 - 20 x 2”
Bolt then tighten with a phillips screwdriver.
b. Attach the back of the chair to the arm by
aligning holes and inserting a 1/4 - 20 x 2” Bolt
thru the arm, leg and into the chair back, then
tighten with a phillips screwdriver.
Repeat on both sides.
4.
Attach the cross braces of the chair to the
legs by aligning holes and inserting a 1/4 - 20 x
2” Bolt through the leg into the cross brace and
tighten with a phillips screwdriver.
Repeat on other leg.
Do Front and Back cross braces.
Repeat on the other front leg.
Copyright © Kettler USA 309.01
5.
Insert the bolt thru the center
seat brace into the center of the
back of bench.
Properly Seated
Washer and Nut.
5.
Attach the center seat brace underneath to
the back, insert a #10 x 3” screw thru the brace
into the center of the bottom back support then
tighten with the screwdriver.
Made in the U.S.A.
www.kettlerusa.com
info@kettlerusa.com
Care & Maintenance
Ocean Comfort products are constructed from HDPE (High Density Polyethelene),
primarily a recycled material. UV inhibitors are also added to resist fading. Simply
maintain your furniture by cleaning with soap and warm water to ensure its long lasting
beauty. A soft bristle brush can be used on any tough to clean stains. Stainless steel
hardware is used in the assembly of these products and should be rinsed regularly with
fresh water if being used in a coastal environment.
KETTLER Limited Warranty
Ocean Comfort products are guaranteed for a period of 20 years (for residential use) and 5
years (for commercial use), starting from original purchase date. This warranty covers defects in
materials and/or workmanship and does not apply to the hardware.
Warranty not applicable to any products deemed as misused, abused or damaged due to an
uncontrollable act of nature.
*For Parts and Service, please contact us directly at 866-804-0440 or email parts@kettlerusa.com
Made in the U.S.A.
KETTLER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453
www.kettlerusa.com • info@kettlerusa.com
Loading...