Kettler 07975-160 User Manual

RUS

SLO

Abb. ähnlich

Auf 100% Altpapier gedruckt!

Montageanleitung für Rudermaschine „COACH E”

A 206cm B 52cm C 67cm

47 kg

30 Min.

max.

130 kg

Art.-Nr. 07975-160

Please read these instructions carefully prior to carrying out assembly and using for the ﬁrst time. They contain information which is important for your safety as well as for the use and maintenance of the appliance. Keep these instructions in a safe place for reference purposes, maintenance work and to assist you when ordering spare parts.

For Your Safety

RISK! While assembly of the product keep off children’s reach

(Choking hazard - contains small parts).

RISK! The device requires a supply voltage of 230V, 50 Hz.

– Connect the power cord with a protective contact socket.

RISK! Any other use of the equipment is prohibited and may

be dangerous. The manufacturer cannot be held liable for damage or injury caused by improper use of the equipment.

RISK! Instruct people using the equipment (in particular chil-

dren) on possible sources of danger during exercising.

RISK! Do not under any circumstances carry out electrical re-

pairs or alterations yourself. Always ensure that such work is done by a properly qualiﬁed electrician.

RISK! disconnect the apparatus from the mains before doing

repair, maintenance or cleaning work.

RISK! Incorrect repairs and structural modiﬁcations (e.g. re-

moval or replacement of original parts) may endanger the safety of the user.

RISK! Heart rate monitoring systems may be inaccurate. Over

exercise may result in serious injury or death. If you feel faint stop exercising immediately.

RISK! All electric appliances emit electromagnetic radiation

when in operation. Please do not leave especially radiation-intensive appliances (e.g. mobile telephones) directly next to the cockpit or the electronic controlsystem as otherwise values displayed might be distorted (e.g. pulse measurement.

RISK! Ensure that the power cable is not pinched and that no-

one can trip over it.

WARNING! The training device should be used only for its in-

tended purpose, i.e. for physical exercise by adult people.

WARNING! Before beginning your program of training, study

the instructions for training carefully.

WARNING! Any interference with parts of the product that

are not described within the manual may cause damage, or endanger the person using this machine. Extensive repairs must only be carried out by KETTLER service staff or qualiﬁed personnel trained by KETTLER.

WARNING! This training device is for home use only. WARNING! If you lose the pulse signal, the performance of

the device will remain constant for approx. 60 seconds and is then slowly adjusted downwards. Please check your pulse measuring system (ear clip, hand pulse or chest belt) so that the pulse signal of the electronics can be entered again.

■ The training device has been designed in accordance with the

latest standards of safety. Any features which may have been a possible cause of injury have been avoided or made as safe as possible.

■ The training device corresponds with DIN EN 957 -1/-7, class

HA. It is therefore unsuitable for therapeutic use.

■ In case of enquiry, please contact your KETTLER dealer.

■ If the equipment is in regular use, check all its components tho-

roughly every 1–2 months. Pay particular attention to the tightness of bolts and nuts. This is particularly true for the attachment of grip strap, running plate and fastening of the handlebar and front tube.

■ Before beginning your program of exercise, consult your doc-

tor to ensure that you are ﬁt enough to use the equipment. Base your program of exercise on the advice given by your doctor. Incorrect or excessive exercise may damage your health!

■ Before use, always check all screws and plug-in connections as

well as respective safety devices ﬁt correctly.

■ Always wear suitable shoes when using.

■ Our products are subject to a constant innovative quality as-

surance. We reserve the right to perform technical modiﬁcations.

■ In choosing the location of the apparatus, ensure a sufﬁcient

safety distance from any obstacles. The apparatus must not be mounted in the immediate vicinity of main passageways (paths, doorways, corridors). The safety distance surrounding must extend at least 1 meter further than the practice area.

■ Always observe the general safety rules and precautions for

working with electrical equipment.

■ Do not use a multiple power socket for the running belt. If an

extension cable is being used, ensure that it complies with the VDE regulations.

■ Unplug the power cord of the device from the socket if not used

for a longer period.

■ Nobody may be in the moving range of a training person du-

ring training

■ This exercise machine may only be used for exercises indica-

ted in the training instructions.

■ This training device has to be set up on a horizontal surface

under all circumstances. Place rubber or straw mats under it to deaden any noise or impacts. Only for appliances with weights. Avoid powerful oscillations of the dumbbells!

■ When mounting the product please take the recommended tor-

que information into account (M = xx Nm).

Instructions for Assembly

RISK! Ensure that your working area is free of possible sources

of danger, for example don’t leave any tools lying around. Always dispose packaging material in such a way that it may not cause any danger. There is always a risk of suffocation if children play with plastic bags!

WARNING! Please note that there is always a danger of injury

when working with tools or doing manual work. Therefore please be careful when assembling this machine.

■ Ensure that you have received all the parts required (see check

list) and that they are undamaged. Should you have any cause for complaint, please contact your KETTLER dealer.

■ Before assembling the equipment, study the drawings carefully

and carry out the operations in the order shown by the diagrams. The correct sequence is given in capital letters.

■ The equipment must be assembled with due care by an adult

person. If in doubt call upon the help of a second person, if pos-

Important Instructions

sible technically talented.

■ The fastening material required for each assembly step is

shown in the diagram inset. Use the fastening material exactly as instructed.

■ Bolt all the parts together loosely at ﬁrst, and check that they

have been assembled correctly. Tighten the locknuts by hand until resistance is felt, then use spanner to ﬁnally tighten nuts

completely against resistance (locking device). Then check that all screw connections have been tightened ﬁrmly. Attention: once locknuts have been unscrewed they no longer function correctly (the locking device is destroyed), and must be replaced.

■ For technical reasons, we reserve the right to carry out preli-

minary assembly work (e.g. addition of tubing plugs).

Handling the equipment

■ Before using the equipment for exercise, check carefully to en-

sure that it has been correctly assembled.

■ It is not recommended to use or store the apparatus in a damp

room as this may cause it to rust. Please ensure that no part of the machine comes in contact with liquids (drinks, perspiration etc.). This may cause corrosion.

■ The machine is designed for use by adults and children should

not be allowed to play with it. Children at play behave unpredictably and dangerous situations may occur for which the manufacturer cannot be held liable. If, in spite of this, children are allowed to use the equipment, ensure that they are instructed in its proper use and supervised accordingly.

■ This Rowing machine is an exercise machine that works de-

pendent from stroke sequence (speed).

■ The training device has a magnetic brake system.

■ To operate correctly, the pulse function requires a minimum vol-

tage of 2,7 volts (only for computers working with batteries).

■ Before beginning your ﬁrst training session, familiarize yourself

thoroughly with all the functions and settings of the unit.

Care and Maintenance

■ Damaged components may endanger your safety or reduce

the lifetime of the equipment. For this reason, worn or damaged parts should be replaced immediately and the equipment taken out of use until this has been done. Use only original KETTLER spare parts.

■ To ensure that the safety level is kept to the highest possible

standard, determined by its construction, this product should be serviced regulary (once a year) by specialist retailers.

■ Use for your regular cleaning, maintenance and care our ap-

pliance maintenance set (Article no. 07921-000) speciﬁcally licensed for KETTLER Sports apparatus and available from the Sport specialized trade.

■ Please ensure that liquids or perspiration never enter the ma-

chine or the electronics.

List of spare parts page 34-36

When ordering spare parts, always state the full article number, spare-partnumber, the quantity required and the S/N of the product (see handling).

Example order: Art. no. 07975-160 / spare-part no. 94317661/

2 pieces / S/N .................... Please keep original packaging of

this article, so that it may be used for transport at a later date, if necessary.

Goods may only be returned after prior arrangement and in (internal) packaging, which is safe for transportation, in the original box if possible. It is important to provide a detailed defect description / damage report!

Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.) is required, this should be clearly stated on the order by adding the words „with fastening

material“.

Waste Disposal

KETTLER products are recyclable. At the end of its useful life please dispose of this article correctly and safely (local refuse sites).

KETTLER GB Ltd. Kettler House, Merse Road North Moons Moat Redditch, Worcestershire B98 9HL

www.kettler.co.uk

+44 1527 591901 +44 1527 62423

sales@kettler.co.uke-mail:

KETTLER International Inc. 1355 London Bridge Road Virginia Beach, VA 23453

www.kettlerusa.com

USA

+1 888 253 8853 +1 888 222 9333

sales@kettler.co.uke-mail:

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M5x40

M8x40

ø22

ø16

ø12

ø3,9x13

M5x40

– GB – Measuring help for screw connections

– F – Gabarit pour système de serrae

– NL – Meethulp voor schroefmateraal

– E – Ayuda para la medición del material de atornilladura

– I – Misura per materiale di avvitamento

– PL – Wzornik do połączeń śrubowych

– CZ – Měřící pomůcka pro materiál k přišroubování

– P – Auxiliar de medição para materiais de aparafusamento

– DK – Hjælp til måling af skruer

– RUS – Справка по определению размеров крепежных

материалов

– SLO – Merilni pripomoček za vijačni material

Messhilfe für Verschraubungsmaterial

Beispiel Examples Examples Voorbeeld Ejemplos Esempio Przykłod Příklad Exemplo Eksempel Примеры Primer

– GB – Checklist (contents of packaging)

– F – Liste de vériﬁcation (contenu de l’emballage)

– NL – Checklijst (verpakkingsinhoud)

– E – Lista de control (contenido del paquete)

– I – Lista di controllo (contenuto del pacco)

– PL – Lista kontrolna (zawartość opakowania)

– CZ – Kontrolní seznam (obsah balení)

– P – Lista de veriﬁcação (conteúdo da embalagem)

– DK – Checkliste (pakkens indhold)

– RUS – Контрольный список

– SLO – Kontrolni seznam (vsebina embalaže)

Checkliste (Packungsinhalt)

– D – Benötigtes Werkzeug – Gehört nicht zum Lieferumfang.

– GB – Tools required – Not included.

– F – Outils nécessaires – Ne fait pas partie du domaine de livraison.

– NL – Benodigd gereedschap – Is niet bij de levering inbegrepen.

– E – Herramientas necesarias – No forma parte del volumen de entrega.

– I – Strumenti necessari – Non in dotazione alla fornitura.

– PL – Narzędzi – Nie należy do zakresu dostawy.

– CZ – Nářadí potřebné – Nepatří do rozsahu dodávky

– P – Ferramentas necessárias – Não está incluído nas peças fornecidas

– DK – Værktøjer kræves – Er ikke inkluderet i leveringsomfanget.

– RUS – Необходимый инструмент - не включены.

– SLO – Potrebna orodja – niso vključeni.

ø13x308 mm

ø13x410 mm

ø46 mm

Checkliste (Packungsinhalt)

1x 1x

+ 9 hidden pages