Kern PES 220-3M, PES 420-3M, PES 620-3M, PES 2200-2M, PES 4200-2M User guide

KERN & Sohn GmbH

Ziegelei 1
D-72336 Balingen
E-Mail: [e-mail]

Tel: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com

Operating instruction
Precision balance

KERN PES/PEJ

Version 1.6

04/2013
GB

PES/PEJ-BA-e-1316

2

GB

KERN PES/PEJ

Version 1.6 04/2013

Operating instruction
Precision balance

Contents

1. Technical data ................................................................................................ 5

2. Declaration of conformity ........................................................................... 10

3. Basic Information (General) ........................................................................ 11

3.1. Proper use .................................................................................................... 11

3.2. Improper Use ................................................................................................ 11

3.3. Warranty ....................................................................................................... 11

3.4. Monitoring of Test Resources .................................................................... 12

4. Basic Safety Precautions ............................................................................ 12

4.1. Pay attention to the instructions in the Operation Manual ...................... 12

4.2. Personnel training ....................................................................................... 12

5. Transport and storage ................................................................................. 12

5.1. Testing upon acceptance ............................................................................ 12

5.2. Packaging ..................................................................................................... 12

6. Unpacking, Setup and Commissioning ..................................................... 13

6.1. Installation Site, Location of Use ............................................................... 13

6.2. Unpacking .................................................................................................... 13

6.3. Scope of delivery ......................................................................................... 15

6.4. Setup ............................................................................................................. 15

6.5. Mains connection ........................................................................................ 16

6.6. Internal battery operation (cannot be reequipped) ................................... 16

6.7. Terminal for external devices ..................................................................... 16

6.8. Initial Commissioning.................................................................................. 17

6.8.1. Power display ........................................................................................... 17

6.8.2. Bar graph display ..................................................................................... 18

6.8.3. Stability display ........................................................................................ 18

6.8.4. Balance zero display ................................................................................ 18

6.9. Adjustment ................................................................................................... 19

PES/PEJ-BA-e-1316

3

6.9.1. Adjustment with external weight (only PES) ......................................... 19

6.9.2. Adjustment test with external weight (only PES) .................................. 21

6.9.3. Automatic adjustment (only PEJ) ........................................................... 23

6.9.4. Adjustment with internal weight (only PEJ) ........................................... 24

6.9.5. Adjustment test with internal weight (only PEJ) ................................... 25

6.10. Verification ................................................................................................ 27

6.10.1. Seals and unlocking switch .................................................................... 28

7. Application and configuration menu 1 ....................................................... 29

7.1. User principle of the menu control ............................................................ 29

7.2. Menu overview ............................................................................................. 31

7.2.1. Parameter additional functions ............................................................... 33

7.2.2. Parameter for serial interface.................................................................. 34

8. Configuration menu 2 .................................................................................. 36

8.1. User principle of the menu control ............................................................ 36

8.2. Menu overview ............................................................................................. 37

9. Operation ...................................................................................................... 38

9.1. Keyboard overview ...................................................................................... 38

9.2. Overview of display ..................................................................................... 39

10. Weighing mode ............................................................................................ 40

10.1. Weighing ................................................................................................... 40

10.1.1. Taring ........................................................................................................ 41

10.1.2. Net/gross ................................................................................................... 43

10.2. Parts counting .......................................................................................... 44

10.3. Percent determination ............................................................................. 47

10.3.1. Entering the reference weight by weighing ........................................... 47

10.3.2. Numeric entering of the reference weight ............................................. 48

10.4. Density determination of solids (hydrostatic weighing) ....................... 51

11. Adding of displayed values ......................................................................... 55

11.1. Adding with AUTO-TARE ......................................................................... 56

12. Weighing with tolerance range ................................................................... 57

12.1. General Information ................................................................................. 57

12.2. Display of the results ............................................................................... 58

12.2.1. For 2 limits ................................................................ ................................ 58

12.2.2. For 3 or 4 limits ........................................................................................ 59

12.3. Basic settings for weighings with tolerance range ............................... 59

12.4. Evaluation of absolute values ................................................................. 60

PES/PEJ-BA-e-1316

4

12.4.1. Entering 2 limits by weighing .................................................................. 60

12.4.2. Entering 3 or 4 limits by weighing .......................................................... 63

12.4.3. Numeric entering of 2 limits .................................................................... 66

12.5. Evaluation with difference values ........................................................... 69

12.5.1. Entering 2 limits by weighing .................................................................. 69

12.5.2. Entering 3 or 4 limits by weighing .......................................................... 72

12.5.3. Numeric entering of 2 limits .................................................................... 72

13. Setting date and time................................................................................... 75

13.1. Time ........................................................................................................... 75

13.2. Date ........................................................................................................... 77

13.3. Interval output function ........................................................................... 79

13.3.1. Interval setting .......................................................................................... 79

13.3.2. Start/Stop interval output ........................................................................ 80

13.4. Input balance ID-no. ................................................................................. 81

14. Data output ................................................................................................... 83

14.1. RS 232C interface ..................................................................................... 83

14.2. Printer interface (unidirectional data exchange) ................................... 84

14.3. Description of interface ........................................................................... 84

14.4. Data output ............................................................................................... 85

14.4.1. Format for data transmission .................................................................. 85

14.4.2. Signs ......................................................................................................... 85

14.4.3. Data ........................................................................................................... 85

14.4.4. Units .......................................................................................................... 86

14.4.5. Result evaluation for balances with tolerance range ............................ 86

14.4.6. Data status ................................................................................................ 87

14.4.7. Interval data output .................................................................................. 87

14.4.8. Output time ............................................................................................... 87

14.5. Remote control instructions ................................................................... 88

15. Service, maintenance, disposal .................................................................. 89

15.1. Cleaning .................................................................................................... 89

15.2. Service, maintenance............................................................................... 89

15.3. Disposal .................................................................................................... 89

16. Instant help ................................................................................................... 89

PES/PEJ-BA-e-1316

5

1. Technical data

KERN

PES 220-3M

PES 420-3M

PES 620-3M

Readability (d)

0.001 g

0.001 g

0.001 g

Weighing range (max)

220 g

420 g

620 g

Minimum load (Min)

0.02 g

0.02 g

0.1 g

Verification value (e)

0.01 g

0.01 g

0.01 g

Accuracy class

II

II

I

Reproducibility

0.001 g

0.001 g

0.001 g

Linearity

± 0.002 g

± 0.003 g

± 0.003 g

Stabilization time

3 sec.

3 sec.

3 sec.

Recommended adjusting
weight, not included (class)

200 g (F1)

2 x 200 g (E2)

500 g (E2)

Vibration filter

4

Minimum piece weight

0.001 g

Reference quantities

5, 10, 30, 100

Net weight (kg)

4kg

Permissible ambient condi­tion

10° C to 30° C

Humidity of air

max. 80 % relative (not condensing)

Weighing Units

g, kg, ct

Weighing plate, stainless
steel

140 x 120 mm

Dimensions of the housing
(B x D x H)

220 x 330 x 93 mm

Mains connection

Mains adaptor 220V-240V; AC; 50Hz

Rechargeable battery
(optional)

Operating time ca. 6 h. / charging time ca. 12 h

PES/PEJ-BA-e-1316

6

KERN

PES 2200-2M

PES 4200-2M

PES 6200-2M

Readability (d)

0.01 g

0.01 g

0.01 g

Weighing range (max)

2,200 g

4,200 g

6,200 g

Minimum load (Min)

0.5 g

0.5 g

1 g

Verification value (e)

0.1 g

0.1 g

0.1 g

Accuracy class

II

II

I

Reproducibility

0.01 g

0.01 g

0.01 g

Linearity

± 0.02 g

± 0.02 g

± 0.03 g

Stabilization time

3 sec.

3 sec.

3 sec.

Recommended adjusting
weight, not included (class)

2 kg (F1)

2 x 2 kg (E2)

5 kg (E2)

Vibration filter

4

Minimum piece weight

0.01g

Reference quantities

5, 10, 30, 100

Net weight (kg)

4kg

Permissible ambient condi­tion

10° C to 30° C

Humidity of air

max. 80 % relative (not condensing)

Weighing Units

g, kg, ct

Weighing plate, stainless
steel

200 x 200 mm

Dimensions of the housing
(B x D x H)

220 x 333 x 93 mm

Mains connection

Mains adaptor 220V-240V; AC; 50Hz

Rechargeable battery
(optional)

Operating time ca. 6 h. / charging time ca. 12 h

PES/PEJ-BA-e-1316

7

KERN

PES 8200-1M

PES 15000-1M

PES 31000-1M

Readability (d)

0.1 g

0.1 g

0.1 g

Weighing range (max)

8,200 g

15,000 g

31,000 g

Minimum load (Min)

5 g

5 g

5 g

Verification value (e)

1 g

1 g

1 g

Accuracy class

II

II

II

Reproducibility

0.1 g

0.1 g

0.1 g

Linearity

± 0.2 g

± 0.2 g

± 0.4 g

Stabilization time

3 sec.

3 sec.

3sec.

Recommended adjusting
weight, not included (class)

5 kg + 2 kg (F1)

10 kg + 5 kg (F1)

20 kg+10 kg(F1)

Vibration filter

4 4 8,9

Minimum piece weight

0.1 g

0.1g

0.5 g

Reference quantities

5,10, 30, 100

Net weight (kg)

4 4 8.9

Permissible ambient condi­tion

10° C to 30° C

Humidity of air

max. 80 % relative (not condensing)

Units

g, kg, ct

Weighing plate, stainless
steel

200x200 mm

200x200 mm

250x220mm

Dimensions of the housing
(B x D x H)

220x333x93 mm

220x333x93 mm

260x330x110

Mains connection

Mains adaptor 220V-240V; AC; 50Hz

Rechargeable battery (op­tional)

Operating time ca. 6 h. / charging time ca. 12 h

PES/PEJ-BA-e-1316

8

KERN

PEJ 220-3M

PEJ 420-3M

PEJ 620-3M

Readability (d)

0.001 g

0.00 1g

0.001 g

Weighing range (max)

220 g

420 g

620 g

Minimum load (Min)

0.02 g

0.02 g

0.1 g

Verification value (e)

0.01 g

0.01 g

0.01 g

Accuracy class

II

II

I

Reproducibility

0.001 g

0.001 g

0.001 g

Linearity

± 0.002 g

± 0.003 g

± 0.003 g

Stabilization time

3 sec.

3 sec.

3 sec.

Adjustment weight

internal

Vibration filter

4

Minimum piece weight

0.001g

Reference quantities

5, 10, 30, 100

Net weight (kg)

4kg

Permissible ambient condi­tion

10° C to 30° C

Humidity of air

max. 80 % relative (not condensing)

Weighing Units

g, kg, ct

Weighing plate, stainless
steel

140 x 120 mm

Dimensions of the housing
(B x D x H)

220 x 333 x 93 mm

Mains connection

Mains adaptor 220V-240V; AC; 50Hz

Rechargeable battery
(optional)

Operating time ca. 6 h. / charging time ca. 12 h

PES/PEJ-BA-e-1316

9

KERN

PEJ 2200-2M

PEJ 4200-2M

Readability (d)

0.01 g

0.01 g

Weighing range (max)

2,200 g

4,200 g

Minimum load (Min)

0.5 g

0.5 g

Verification value (e)

0.1 g

0.1 g

Accuracy class

II

II

Reproducibility

0.01 g

0.01 g

Linearity

± 0.02 g

± 0.02 g

Stabilization time

3 sec.

Adjustment weight

internal

Vibration filter

4

Minimum piece weight

0.01 g

Reference quantities

5,10, 30, 100

Net weight (kg)

6

Permissible ambient condi­tion

10° C to 30° C

Humidity of air

max. 80 % relative (not condensing)

Units

g, kg, ct

Weighing plate, stainless
steel

200 x 200 mm

Dimensions of the housing
(B x D x H)

220 x 333 x 93 mm

Mains connection

Mains adaptor 220V-240V; AC; 50Hz

Rechargeable battery (op­tional)

Operating time ca. 6 h. / charging time ca. 12 h

PES/PEJ-BA-e-1316

10

2. Declaration of conformity

KERN & Sohn GmbH

Ziegelei 1
D-72336 Balingen
E-Mail: [e-mail]

Tel: 0049-[0]7433- 9933-0
Fax: 0049-[0]7433-9933-149
Internet: www.kern-sohn.com

D

Konformitäts­erklärung

Wir erklären hiermit, dass das Produkt, auf das sich diese Erklärung bezieht,
mit den nachstehenden Normen übereinstimmt.

GB

Declaration of
conformity

We hereby declare that the product to which this declaration refers conforms
with the following standards.

CZ

Prohlášení o

shode

Tímto prohlašujeme, že výrobek, kterého se toto prohlášení týká, je v souladu
s níže uvedenými normami.

E

Declaración de
conformidad

Manifestamos en la presente que el producto al que se refiere esta
declaración está de acuerdo con las normas siguientes

F

Déclaration de
conformité

Nous déclarons avec cela responsabilité que le produit, auquel se rapporte la
présente déclaration, est conforme aux normes citées ci-après.

I

Dichiarazione di
conformitá

Dichiariamo con ciò che il prodotto al quale la presente dichiarazione si riferi­sce è conforme alle norme di seguito citate.

NL

Conformiteit­verklaring

Wij verklaren hiermede dat het product, waarop deze verklaring betrekking
heeft, met de hierna vermelde normen overeenstemt.

P

Declaração de
conformidade

Declaramos por meio da presente que o produto no qual se refere esta
declaração, corresponde às normas seguintes.

PL

Deklaracja

zgodności

Niniejszym oświadczamy, że produkt, którego niniejsze oświadczenie dotyczy,

jest zgodny z poniższymi normami.

RUS

Заявление о

соответствии

Мы заявляем, что продукт, к которому относится данная декларация,

соответствует перечисленным ниже нормам.

EU Directive

Standards

2004/108/EC

EN 61000-3-2:2006/A1:2009/A2:2009
EN 61000-3-3:2008
EN 55022:2006/A1:2007
EN 55024:1998/A1:2001/A2:2003

2006/95/EC

EN60950-1:2006/A11:2009/A1:2010/A12:2011

Signatur

Signature

Datum

Date

20.03.2013

Ort der Ausstellung

Place of issue

72336 Balingen

Albert Sauter
KERN & Sohn GmbH

Geschäftsführer

Managing director

KERN & Sohn GmbH, Ziegelei 1, D-72336 Balingen, Tel. +49-[0]7433/9933-0
Fax +49-[0]7433/9933-149, E-Mail: [e-mail], Internet: www.kern-sohn.com

Declaration of conformity

EC-Konformitätserklärung EC-Declaration of -Conformity
EC- Déclaration de conformité EC-Declaración de Conformidad
EC-Dichiarazione di conformità EC-Conformiteitverklaring
EC- Declaração de conformidade EC- Prohlášení o shode
EC-Deklaracja zgodności EC-Заявление о соответствии

Electronic Balance: KERN PES/PEJ

PES/PEJ-BA-e-1316

11

3. Basic Information (General)

The appliance may only be opened by trained service technicians according to
KERN standards.

Before opening, disconnect appliance from power supply!
Warranty claims will be voided when appliance is opened.

The PES/PEJ weighing system may not be used in explosive areas or areas
with explosive substances.

3.1. Proper use

The balance you purchased is intended to determine the weighing value of material
to be weighed. It is intended to be used as a “non-automatic“ balance, i.e. the ma­terial to be weighed is manually and carefully placed in the centre of the weighing
plate. As soon as a stable weighing value is reached the weighing value can be read.

3.2. Improper Use

Do not use balance for dynamic weighings. In the event that small quantities are re­moved or added to the material to be weighed, incorrect weighing results can be dis-

played due to the “stability compensation“ in the balance. (Example: Slowly draining

fluids from a container on the balance.)
Do not leave permanent load on the weighing plate. This may damage the measur­ing system. Impacts and overloading exceeding the stated maximum load (max) of
the balance, minus a possibly existing tare load, must be strictly avoided. This could
cause damage to the balance.
Never operate balance in explosive environment. The serial version is not explosion
protected. The structure of the balance may not be modified. This may lead to incor­rect weighing results, safety-related faults and destruction of the balance.
The balance may only be used according to the described conditions. Other areas of
use must be released by KERN in writing.

3.3. Warranty

Warranty claims shall be voided in case

our conditions in the operation manual are ignored
the appliance is used outside the described uses
when the appliance is modified or opened
mechanical damage and damage caused by media, liquids
natural wear and tear
the appliance is improperly set up or incorrectly electrically connected
the measuring system is overloaded

PES/PEJ-BA-e-1316

12

3.4. Monitoring of Test Resources

Carefully read this operation manual before setup and com­missioning, even if you are already familiar with KERN bal­ances.

Versions in other languages are non-binding translations.
The only binding version is the original document in German.

In the framework of quality assurance the measuring-related properties of the bal­ance and, if applicable, the testing weight, must be checked regularly. The responsi­ble user must define a suitable interval as well as type and scope of this test. Infor­mation is available on KERN’s home page (www.kern-sohn.com) with regard to the
monitoring of balance test substances and the test weights required for this. In
KERN’s accredited DKD calibration laboratory test weights and balances may be
calibrated (return to the national standard) fast and at moderate cost.

4. Basic Safety Precautions

4.1. Pay attention to the instructions in the Operation Manual

4.2. Personnel training

The appliance may only be operated and maintained by trained personnel.

5. Transport and storage

5.1. Testing upon acceptance

When receiving the appliance, please check packaging immediately, and the
appliance itself when unpacking for possible visible damage.

5.2. Packaging

Keep all parts of the original packaging in case you need to return the appliance.
Only use original packaging for returning.
Before sending, disconnect all connected cables and loose/movable parts.
Attach possibly existing transport safeguards. Secure all parts, e.g. glass windshield,
weighing plate, power unit etc., to prevent slipping and damage.

PES/PEJ-BA-e-1316

13

6. Unpacking, Setup and Commissioning

6.1. Installation Site, Location of Use

The balances are designed in a way that reliable weighing results are achieved in
common conditions of use.
You will work accurately and fast, if you select the right location for your balance.

Therefore, observe the following for the installation site:

Place the balance on a firm, level surface;
Avoid extreme heat as well as temperature fluctuation caused by instal-

ling next to a radiator or in the direct sunlight;

Protect the balance against direct draughts due to open windows and

doors;
Avoid jarring during weighing;
Protect the balance against high humidity, vapours and dust;
Do not expose the device to extreme dampness for longer periods of

time. Non-permitted condensation (condensation of air humidity on the

appliance) may occur if a cold appliance is taken to a considerably war-

mer environment. In this case, acclimatize the disconnected appliance

for ca. 2 hours at room temperature.
Avoid static charging of the material to be weighed, weighing container

and windshield.

If electro-magnetic fields or static charge occur, or if the power supply is unstable
major deviations on the display (incorrect weighing results) are possible. In that case,
the location must be changed.

6.2. Unpacking

Carefully remove the balance from the packaging, remove plastic cover and setup
balance at the intended workstation.

PES/PEJ-BA-e-1316

14

Air bubble

Covering lid over
underfloor
weighing device

Connection net adapter
Antitheft device

Rear view:

Your balance in overview:

RS 232 interface
Printer interface

PES/PEJ-BA-e-1316

15

6.3. Scope of delivery

Positioning of weighing plate:

Levelling balance:

Use the foot screws to level the
balance until the air bubble in
the bubble level is in the pre­scribed circle.

Serial accessories:

Balance
Weighing plate
Mains power supply
Operating Manual
Protective cover

6.4. Setup

PES/PEJ-BA-e-1316

16

6.5. Mains connection

Battery charge sufficient

Battery very low. To charge the battery, connect it to the mains
as soon as possible (re-calibration not possible).

flashes

Voltage has dropped below prescribed minimum. Plug in the
mains adapter, to charge the balance via the electrical network
(15h).

RS 232 interface
Printer interface

Power is supplied via the external mains power supply. The stated voltage value
must be the same as the local voltage.
Only use original KERN mains power supplies. Using other makes requires consent
by KERN.

In the menu you can activate the AUTO-SLEEP function . In net operation
the balance after 3 min without load change or key pressure passes in a sleep mode.
Automatic activation of the display by load change or by pressing any key.

6.6. Internal battery operation (cannot be reequipped)
The optionally supplied battery is charged with the supplied power supply.

Before the first use, the battery should be charged by connecting it to the mains
power supply for at least 15 hours. The operating time of the battery is about. 6h;
charging time until complete recharging ca. 15h.

In the menu you can activate the AUTO-OFF function . After 3 min without
load change the balance switches automatically off in order to spare the battery.

When the balance is in battery mode the following symbols appear on the display:

6.7. Terminal for external devices

PES/PEJ-BA-e-1316

17

6.8. Initial Commissioning

The balance will carry out a self-test

Supply balance with power via the
mains power supply.

Balance is in stand-by mode
(green LED is on).

Use the -key to switch the bal­ance on.

g

g

By pressing lightly it is possible to
check whether the balance display
changes.

Stand-by



Use the -key to switch the bal­ance off. The balance is now in
stand-by mode again (green LED
is on).

A warming up time of 10 minutes after switching on stabilizes the measuring values.
The accuracy of the balance depends on the local acceleration of gravity.

Please be sure to observe the information in the chapter on adjusting in chap. 6.9.

6.8.1. Power display

PES/PEJ-BA-e-1316

18

6.8.2. Bar graph display

Hide bar graph

*

Show bar graph

Wägeplatte ist unbelastet halbe Höchstlast Waage ist mit Höchstlast belastet

weihging dish unloaded half of weighing range weighing range is used
to full capacity

In configuration menu 1 (chapter 7) you can activate/deactivate the bar graph dis­play.

The weighing range of the balance is divided into 40 graphic cuboids. Zero (0) will
appear on the graphic display if there is no weighing value on the balance. 20 graph­ic cuboids are displayed if the balance is loaded up to one half of its weighing range.

6.8.3. Stability display

Stable

Unstable

If the display shows the stability display [ο] the balance is in a stable status. The [ο]
indication disappears if the condition is unstable.

6.8.4. Balance zero display

Environmental influences can lead to the exact figure of “000.0“ not being displayed
in spite of an empty weighing dish. It is, however, possible to reset your balance to
zero at any time and thus ensure that weighing really does commence at zero. Set­ting to zero when a weight is applied is only possible within a certain type-dependent
range. In the event that the balance cannot be reset to zero with an applied weight,
this range has been exceeded. [o - Err ] will appear on the display.
If an exact zero reading is not displayed on the balance in spite of the weighing dish
being empty, press the TARE key and the balance will start resetting to zero. Your
balance will be set to zero after a short standby time.
In addition to this, the sign for the balance zero setting will be displayed [ 0 ].

PES/PEJ-BA-e-1316

19

Model

Recommended

adjusting weight

Not ideal for metrological adjustment

PES 220-3M

200 g (F1)

100 g

PES 420-3M

2 x 200 g (E2)

200 g

PES 620-3M

500 g (E2)

300 g

PES 2200-2M

2 kg (F1)

1000 g

PES 4200-2M

2 x 2 kg (E2)

2000 g

PES 6200-2M

5 kg (E2)

3000 g

PES 8200-1M

5 kg + 2 kg (F1)

4000 g

PES 15000-1M

10 kg + 5 kg (F1)

7000 g

6.9. Adjustment

As the acceleration value due to gravity is not the same at every location on earth,
each balance must be coordinated - in compliance with the underlying physical
weighing principle - to the existing acceleration due to gravity at its place of location
(only if the balance has not already been adjusted to the location in the factory). This
adjustment process must be carried out at every commissioning, after each change
of location as well as in case of fluctuating environment temperature. To receive ac­curate measuring values it is also recommended to adjust the balance periodically in
weighing operation.

6.9.1. Adjustment with external weight (only PES)

Adjustment should be carried out with the recommended adjusting weight (see
Chapter 1 „Technical Data“). The adjustment can also be carried out with different
adjusting weights (see table), but not ideal from a metrological point of view.

Information concerning the adjusting weights is available at: http://www.kern-sohn.com

Procedure when adjusting:

Observe stable environment conditions. A warming-up time of ca. 30 minutes for
stabilisation is necessary. Ensure that there are no objects on the weighing plate.
At verified balances, the adjustment is locked by a switch (except accuracy class I).
In order to adjust, open the locking switch see chap.6.10.1 (except accuracy class I).

PES/PEJ-BA-e-1316

20

Operation

Display

Activate function [ ] (see chap. 7).



g

Zero point will be saved.

CAL



CAL

Carefully place adjusting weight in the centre
of the weighing plate

Adjustment process is started.

The process of adjustment is completed.

Remove adjusting weight, balance will return
into weighing mode automatically. In case of
an adjustment error or incorrect adjusting
weight the display will show [- Err]; repeat
adjustment process.

CAL



CAL





CAL



g

PES/PEJ-BA-e-1316

21

6.9.2. Adjustment test with external weight (only PES)

Operation

Display

Activate function [ ]
(see chap. 7).



g

During adjustment tests the balance automatically compares the saved value of the
adjustment weight with the actual value. This is only a check, i.e. no values are
changed.

Procedure:

Observe stable environmental conditions. A warming up time of ca. 1 hour is re­quired for stabilization. Ensure that there are no objects on the weighing plate.

PES/PEJ-BA-e-1316

22

Start of the adjustment test:

Carefully place adjusting weight in the
centre of the weighing plate

The difference between the saved value
and the measured value is displayed.

Take away adjustment weight.
Press any key; the adjustment process is

cancelled and the balance returns to
weighing mode.

CAL



CAL



CAL



CAL





g



CAL



g

PES/PEJ-BA-e-1316

23

Switch on the balance using ON/OFF.

The balance carries out a selftest, „M“

will be displayed flashing.
After that the automatic adjustment

starts:

„Aut. CAL“ appears flashing,
followed by „CH. 0“ and „CH. F.S.“

If „End“ is displayed, the automatic ad-

justment has been concluded success­fully.

The balance changes into weighing
mode thus being ready for weighing.











g

6.9.3. Automatic adjustment (only PEJ)

After switching on the balance, the automatic adjustment starts with the internal ad­justment weight.

PES/PEJ-BA-e-1316

24

6.9.4. Adjustment with internal weight (only PEJ)

Operation

Display

Activate function [ ]
(see chap. 7).



g

Start of the automatic adjustment:

Adjustment is carried out automatically.

The process of adjustment is completed.

The balance returns automatically into
weighing mode.

CAL





CAL



CAL





With the internal adjustment weight, the weighing accuracy can be checked and re­adjusted at any time.

Procedure when adjusting:

Observe stable environmental conditions. A warming up time of ca. 1 hour is re­quired for stabilization. Ensure that there are no objects on the weighing plate.

PES/PEJ-BA-e-1316

25

CAL



g

Operation

Display

Activate function [ ]
(see chap. 7).



g

Start of the adjustment test:

The test is carried out automatically.

CAL





CAL



6.9.5. Adjustment test with internal weight (only PEJ)

During adjustment tests the balance automatically compares the saved value of the
adjustment weight with the actual value. This is only a check, i.e. no values are
changed.

Procedure:

Observe stable environmental conditions. A warming up time of ca. 1 hour is re­quired for stabilization. Ensure that there are no objects on the weighing plate.

PES/PEJ-BA-e-1316

26

CAL

The difference between the saved value
and the measured value is displayed.

Press any key; the adjustment process is
cancelled and the balance returns to
weighing mode.



g





g

PES/PEJ-BA-e-1316

27

6.10. Verification

General introduction:
According to EU directive 90/384/EEC balances must be officially verified if they are

used as follows (legally controlled area):

a) For commercial transactions if the price of goods is determined by weighing
b) For the production of medicines in pharmacies as well as for analyses in the

medical and pharmaceutical laboratory
c) For official purposes.
d) For manufacturing final packages.

In cases of doubt, please contact your local trade in standard.
Verification instructions

An EU type approval exists for balances described in their technical data as verifya­ble. If a balance is used where obligation to verify exists as described above, it must
officially verified and re-verified in regular intervals.
Re-verification of a balance is carried out according to the respective national regula­tions. The validity for verification of balances in Germany is e.g. 2 years.
The legal regulation of the country where the balance is used must be observed!

Balances with obligation to verify must be taken out of operation if:

The weighing result of the balance is outside the error limit. Therefore, in

regular intervals load balance with known test weight (ca. 1/3 of the max. load)

and compare with displayed value.

The reverification deadline has been exceeded.

Before models PES 2200-2M, PES 4200-2M, PES 8200-1M, PES 15000-1M are
verified, the adjustment function „ “ must be activated.

Therefore, external adjustment in verification mode is impossible

PES/PEJ-BA-e-1316