Keri Systems LAN-520 User Manual
LAN-520 AESP
LAN-520 AESP
10/100 Ethernet/MAC Port
4 Status LEDs
RJ-45
Connector
Power Cycle Switch
Reset to Factory Default Jumper
MAC
Address
Label
mac address
Installation Guide
1.0 Basic LAN Device Setup
The following are basic setup instructions for the LAN-520 AESP. Some settings may not apply to every application.
NOTE: The LAN-520 AESP is an updated version of Keri’s LAN-520X device. If you are using the new NC-485X
Network Converter with the LAN-520, you must use the LAN-520 AESP module (or the existing LAN-520X module).
The original NC-485 Network Converter is NOT compatible with the new LAN-520 AESP (or the existing LAN-520X
module).
NOTE: To set up the LAN-520 AESP, you MUST have technical knowledge of general networking in a PC
environment. Please have a Network Administrator on site to resolve any special networkin g issues that might occur
during device programming. Network topologies and strategies will vary.
Figure 1: The LAN-520 AESP Unit
Page 1 of 13 P/N: 01519-001 Rev. B
LAN-520 AESP
LAN-520 AESP
Network
PXL-500
Master Controller
Lithium
Battery
JP6
JP7
NOTE: These jumpers
MUST
be removed
or the LAN
connection will fail.
Installation Guide
2.0 Installing the LAN-520 AESP to a PXL-500
1. Power down the PXL-500 master controller.
2. On the master PXL-500 controller, remove jumpers from JP6 and JP7.
3. Insert the LAN-520 AESP into TB13 on the PXL-500. Orient the unit as shown in Figure 1.
NOTE: Mounting screws are supplied to secure the LAN-520 AESP to the PXL. The PXL will have to be removed from its
enclosure to do this.
4. Connect the RJ-45 port on the LAN-520 AESP to the network via a patch cable or directly to the host PC via a crossover cable.
5. Power up the PXL-500 (if this is a new PXL panel, a RAM reset is required).
Figure 2: Installing the LAN-520 AESP
Page 2 of 13 P/N: 01519-001 Rev. B
LAN-520 AESP
Alarm
Relay
Lock
Relay
GP
Output
Relay 2
GP
Output
Relay 1
6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 1
3
2
1
6 5 4 3 2 1
1 2 3
2 1
485
U18
U2
Battery
D20 D18
D30
D29
D25
D32
SW1
R75
J3
J1
J6
J8
Internal
Modem
J11
J16 - Postal Lock Connection
JP1
JP2
J19J20
U5
J9
TB15
TB1
TB3TB4 TB10
TB12
Modem Module
LAN
Communication
Jumpers
J7
LAN-520
Connector
RxD
DTR
TxD
D41
LAN-520
AESP
NOTE: These jumpers MUST
be removed or connection will fail.
NETWORK
Mounting Stando
Installation Guide
3.0 Installing the LAN-520 AESP on an Entraguard Unit
Support for the LAN unit on Entraguard begin with PCB 23217-001 Rev. E. Earlier units cannot support a LAN unit.
1. Power down the Entraguard master controller.
2. On the Entraguard PCB, remove jumpers from J11, J19, and J20.
3. Insert the LAN-520X into J7 on the Entraguard. Orient the LAN unit as shown in Figure 2.
NOTE: Mounting screws are supplied to secure the LAN-520X to the Entraguard unit. The Entraguard PCB will have to
be removed from its enclosure to do this.
4. Connect the RJ-45 port on the LAN-520 AESP to the network via a patch cable or directly to the host PC via a crossover cable.
5. Power up the Entraguard unit (if this is a new Entraguard panel, a RAM reset is required).
Figure 3: Installing the LAN-520 AESP on an Entraguard
Page 3 of 13 P/N: 01519-001 Rev. B
LAN-520 AESP
Installation Guide
4.0 DHCP Setting
The new LAN-520 AESP has DHCP enabled by default. When the LAN-520 AESP module is connected to a DHCP
enabled router it automatically receives an IP address. The quickest way to find out what DHCP address has been
assigned to the module is to install and run Lantronix Device Installer.
4.1 Installing the Lantronix Device Installer
The Lantronix Device Installer program is found on the software disc. You will not need an active internet connection as
all the required components are included in the installation program.
1. Explore the contents of the installation disk and locate a folder named 'Lantronix Device Installer'.
2. Double-click the 'Installer_KeriSystems' executable.
3. If you are using the Doors.NET software you will see the same 'Lantronix Device Installer' folder on the disk but
inside there will also be a subfolder named 'Updated_Lantronix'. Go into that folder and double-click the
'Device_Installer_v4' executable.
4. You should see a notification window informing you that .NET Framework and Device installer are both required
along with their version numbers. The .NET call out will not appear if the .NET Framework 4.0 is already installed.
5. Click Install to proceed.
6. Place a tick in the checkbox to confirm you have read the Microsoft Terms and Agreements.
Page 4 of 13 P/N: 01519-001 Rev. B
Loading...