KEPCO KIT 219-0449 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

CABLE KIT NO. 219-0449

BOP 1000W MODELS (2) IN PARALLEL

This kit contains the cables and terminations required to operate two identical 1000 Watt BOP High Power mod­els in parallel, effectively multiplying the output current capacity by two. Only identical models may be configured
to operate in parallel.

This kit can be used with all 1000W BOP models that have revision levels as shown in Table 1. Earlier models

!

that have been upgraded to permit multiple unit configurations must include the letter “A” following the revision
number. CAUTION: Failure to install the ground cables supplied can result in damage to the power supply.

Refer to the associated technical manual supplied with the 1000W BOP power supply for all instructions regard­ing installation and operation of multiple units in parallel.

TABLE 1. REVISION LEVELS APPLICABLE TO THIS KIT

MG Model Revision

BOP 6-125MG All All

BOP 10-75MG 5 or higher 3A or 4A

BOP 20-50MG 8 or higher 5A, 6A or 7A BOP 20-50GL All

BOP 25-40MG All All

BOP 36-28MG 11 or higher 8A, 9A or 10A

BOP 50-20MG 7 or higher 5A or 6A BOP 50-20GL All

BOP 72-14MG 7 or higher 6A

BOP 100-10MG 6 or higher 2A or 4A

Revisions for previously Upgraded

Units (Must include “A”)

GL Model Revision

219-0449

I. SPECIFICATIONS

Table 3 lists the model parameters unique to a parallel combination of two identical 1000W BOP Power Supplies.
Table 4 lists the general specifications for the parallel combinations listed in Table 3. For specifications not listed
in Table 3, refer to the General Specifications provided in the associated technical manual supplied with each
1000W BOP power supply

Item Quantity Purpose

Common power cable **

Master - IN Parallel Control

** For GL units: Unclamp and remove ferrite from cable before installation.

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

(1.5 ft.)

Output Power cable

(1.5 ft.)

Digital Control (Bitbus)

Cable ** (1.5 ft.)

Parallel Control Cable

(1.5 ft.)

Protection Cable

(1 ft.)

Termination

TABLE 2. EQUIPMENT SUPPLIED

Connects the COMMON terminal of the Master to the COMMON terminal of the

1

Slave #1.

Connects the OUTPUT terminal of the Master to the OUTPUT terminal of the

1

Slave #1.

Provides communication between master and slave. 118-1108

1

Provides control signals required for parallel operation. 118-1119

1

Provides interlock protection signals required for multiple unit operation. 118-1126

1

1 Provides proper termination for Parallel Control Cable. 195-0109

http://www.kepcopower.com  email: [e-mail]

228-1485 REV 7 051812

Kepco Part

Number

118-1129

118-1112

TABLE 2. EQUIPMENT SUPPLIED (CONTINUED)

Item Quantity Purpose

Protection - OUT Termination

1 Provides proper termination for the slave connection to the Protection Cable. 195-0108

Kepco Part

Number

(Slave)

Protection - IN Termination

(Master)

1 Provides proper termination for the master connection to the Protection Cable. 195-0107

Chassis Ground Cable 1 Connects chassis ground terminals of all units. 118-1272

Ground Cable mounting

hardware

2 sets Each set consists of eight parts, mounted in the following order: No. 10 star

lockwasher P/N 103-0106 (at chassis), No. 10 flat washer P/N 103-0031, No. 10
split lockwasher P/N 103-0033, 10-32X3/8 nut P/N 102-0008, No. 10 flat washer
P/N 103-0031, [lug(s) from ground cable], No. 10 flat washer P/N 103-0031, No.

(See
Purpose
at left for

part

numbers)

10 split lockwasher P/N 103-0033, and 10-32X3/8 nut P/N 102-0008.

Instruction

Manual

Nut 2 Overcomes tight space for output cable connections. After securing bottom

1 Lists material supplied. 228-1485

102-0046
cable to output terminal stud using one nut, additional cables can be oriented
for best layout and secured with separate nut.

II. SPECIFICATIONS

Table 3 lists the model parameters unique to a parallel combination of two 1000W BOP Power Supplies. Table 4
lists the general specifications applicable all the parallel combinations listed in Table 3.

TABLE 3. MODEL PARAMETERS FOR TWO (2) HIGH POWER BOP 1000 WATT UNITS (PARALLEL)

(2) Identical Models

(Parallel)

BOP 6-125MG ±6V d-c ±250A d-c 0.6 25.0

BOP 10-75MG ±10V d-c ±150A d-c 1.0 15.0

BOP 20-50MG ±20V d-c ±100A d-c 2.0 10.0

BOP 25-40MG ±25V d-c ±80A d-c 2.5 8.0

BOP 36-28MG ±36V d-c ±56A d-c 3.6 5.6

BOP 50-20MG ±50V d-c ±40A d-c 5.0 4.0

BOP 72-14MG ±72V d-c ±28A d-c 7.2 2.8

BOP 100-10MG ±100V d-c ±20A d-c 10.0 2.0

d-c Output Range Closed Loop Gain

E

O Max

I

O Max

Voltage Channel

(V/V)

Current Channel

(A/V)

TABLE 4. GENERAL SPECIFICATIONS FOR TWO (2) IDENTICAL BOP 1000 WATT UNITS (PARALLEL)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 19.0A a-c maximum

264 Va-c 13A a-c maximum

Leakage current 7mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

Programming
resolution / accuracy

Voltage 14 bits / 0.2% 2% accuracy for Ext Ref Level. Unit gain

Current 14 bits / 0.5%

adjustable between 0 and E
or I

ONOM

/10 (current).

ONOM

/10 (voltage)

Voltage Limit 12 bits / 0.5%

Current Limit 12 bits / 0.5%

Readback
resolution / accuracy

Voltage 16 bits / 0.2% main or limit channel

Current 16 bits / 0.5% main or limit channel

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1485 REV 7 051812