KEPCO KIT 219-0447 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

219-0447

CABLE KIT NO. 219-0447

BOP 1000W MODELS (4) IN PARALLEL

I. DESCRIPTION.

This kit contains the cables and terminations required to operate four identical 1000 Watt BOP High Power mod­els in parallel, effectively multiplying the output current capacity by four. Only identical models may be configured
to operate in parallel.

This kit can be used with all 1000W BOP models that have revision levels as shown in Table 1. Earlier models

!

that have been upgraded to permit multiple unit configurations must include the letter “A” following the revision
number. CAUTION: Failure to install the ground cables supplied can result in damage to the power supply.

Refer to the associated technical manual supplied with the 1000W BOP power supply for all instructions regard­ing installation and operation of multiple units in parallel.

TABLE 1. REVISION LEVELS APPLICABLE TO THIS KIT

MG Model Revision

BOP 6-125MG All All

BOP 10-75MG 5 or higher 3A or 4A

BOP 20-50MG 8 or higher 5A, 6A or 7A BOP 20-50GL All

BOP 25-40MG All All

BOP 36-28MG 11 or higher 8A, 9A or 10A

BOP 50-20MG 7 or higher 5A or 6A BOP 50-20GL All

BOP 72-14MG 7 or higher 6A

BOP 100-10MG 6 or higher 2A or 4A

Revisions for previously Upgraded

Units (Must include “A”)

GL Model Revision

II. SPECIFICATIONS

Table 3 lists the model parameters unique to a parallel combination of four identical 1000W BOP Power Supplies.
Table 4 lists the general specifications for the parallel combinations listed in Table 3. For specifications not listed
in Table 3, refer to the General Specifications provided in the associated technical manual supplied with each
1000W BOP power supply.

TABLE 2. EQUIPMENT SUPPLIED

Item Quantity Purpose

Common power cable **

(1.5 ft.)

Common power cable **

(3 ft.)

Common power cable **

(4.5 ft.)

Output Power cable

(1.5 ft.)

Output Power cable

(4.5 ft.)

Output Power cable

(3 ft.)

** For GL units: Unclamp and remove ferrite from cable before installation.

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

Connects the COMMON terminal Master to the COMMON terminal of

1

Slave #1.

Connects the COMMON terminal Master to the COMMON terminal of

1

Slave #2.

Connects the COMMON terminal Master to the COMMON terminal of

1

Slave #3.

Connects the OUTPUT terminal of Master to the OUTPUT terminal of

1

Slave #1.

Connects the OUTPUT terminal of Master to the OUTPUT terminal of

1

Slave #3.

Connects the OUTPUT terminal of Master to the OUTPUT terminal of

1

Slave #2.

http://www.kepcopower.com  email: [e-mail]

228-1527 REV 3 033012

Kepco Part

Number

118-1129

118-1153

118-1155

118-1112

118-1154

118-1152

TABLE 2. EQUIPMENT SUPPLIED (CONTINUED)

Item Quantity Purpose

Digital Control (Bitbus) Cable

(4.5 ft.)

Parallel Control Cable

(1.5 ft.)

Protection Cable

(1 ft.)

Master - IN Parallel
Control Termination

Protection - OUT Termination

(Slave)

Protection - IN Termination

(Master)

Chassis Ground Cable 3 Connects chassis ground terminals of all units. 118-1272

Ground Cable mounting hardware 4 sets Each set consists of eight parts, mounted in the following order: No. 10

Nut 2 Overcomes tight space for output cable connections. After securing bot-

Instruction Manual 1 Lists material supplied and specifications for multiple unit combination. 228-1527

1 Provides communication between master and three slaves. 118-1149

3 Provides control signals required for parallel operation. 118-1119

3 Provides interlock protection signals required for multiple unit operation. 118-1126

1 Provides proper termination for Parallel Control Cable. 195-0109

1 Provides proper termination for the slave connection to the Protection

Cable.

1 Provides proper termination for the master connection to the Protection

Cable.

star lockwasher P/N 103-0106 (at chassis), No. 10 flat washer P/N 103­0031, No. 10 split lockwasher P/N 103-0033, 10-32X3/8 nut P/N 102­0008, No. 10 flat washer P/N 103-0031, [lug(s) from ground cable], No.
10 flat washer P/N 103-0031, No. 10 split lockwasher P/N 103-0033,
and 10-32X3/8 nut P/N 102-0008.

tom cable to output terminal stud using one nut, additional cables can
be oriented for best layout and secured with separate nut.

Kepco Part

Number

195-0108

195-0107

(See
Purpose
at left for

part

numbers)

102-0046

TABLE 3. MODEL PARAMETERS FOR FOUR (4) IDENTICAL BOP 1000 WATT UNITS (PARALLEL)

(4) Identical Models

(Parallel)

BOP 6-125MG ±6V d-c ±500A d-c 0.6 50.0

BOP 10-75MG ±10V d-c ±300A d-c 1.0 30.0

BOP 20-50MG ±20V d-c ±200A d-c 2.0 20.0

BOP 25-40MG ±25V d-c ±160A d-c 2.5 16.0

BOP 36-28MG ±36V d-c ±112A d-c 3.6 11.2

BOP 50-20MG ±50V d-c ±80A d-c 5.0 8.0

BOP 72-14MG ±72V d-c ±56A d-c 7.2 5.6

BOP 100-10MG ±100V d-c ±40A d-c 10.0 4.0

d-c Output Range Closed Loop Gain

E

O Max

I

O Max

Voltage Channel

(V/V)

Current Channel

(A/V)

TABLE 4. GENERAL SPECIFICATIONS FOR FOUR (4) IDENTICAL BOP 1000 WATT UNITS (PARALLEL)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 36.0A a-c maximum

264 Va-c 25.6A a-c maximum

Leakage current 14mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

Programming
resolution / accuracy

Readback
resolution / accuracy

Voltage 14 bits / 0.2% 2% accuracy for Ext Ref Level. Unit gain

Current

Voltage Limit 12 bits / 0.5%

Current Limit 12 bits / 0.5%

Voltage 16 bits / 0.2% main or limit channel

Current 16 bits / 0.5% main or limit channel

14 bits / 0.5%

adjustable between 0 and E
or I

ONOM

/10 (current).

ONOM

/10 (voltage)

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1527 REV 3 033012