KEPCO KIT 219-0444 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

219-0444

CABLE KIT NO. 219-0444

BOP 1000W MODELS (3) IN SERIES

I. DESCRIPTION.

This kit contains the cables and terminations required to operate three identical 1000 Watt BOP High Power mod­els in series, effectively multiplying the output voltage capacity by three. Only identical models may be configured
to operate in series.

This kit can be used with all 1000W BOP models that have revision levels as shown in Table 1. Earlier models

!

that have been upgraded to permit multiple unit configurations must include the letter “A” following the revision
number. CAUTION: Failure to install the ground cables supplied can result in damage to the power supply.

Refer to the associated technical manual supplied with the High Power BOP power supply for all instructions
regarding installation and operation of multiple units in series.

TABLE 1. REVISION LEVELS APPLICABLE TO THIS KIT

Model Revision

BOP 6-125MG All All

BOP 10-75MG 5 or higher 3A or 4A

BOP 20-50MG 8 or higher 5A, 6A or 7A

BOP 25-40MG All All

BOP 36-28MG 11 or higher 8A, 9A or 10A

BOP 50-20MG 7 or higher 5A or 6A

BOP 72-14MG 7 or higher 6A

BOP 100-10MG 6 or higher 2A or 4A

Revisions for Upgraded Units

(Must include “A”)

II. SPECIFICATIONS

Table 3 lists the model parameters unique to a series combination of three identical 1000W BOP Power Supplies.
Table 4 lists the general specifications for the series combinations listed in Table 3. For specifications not listed in
Table 3, refer to the General Specifications provided in the associated technical manual supplied with each
1000W BOP power supply

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

http://www.kepcopower.com  email: [e-mail]

228-1525 REV 3 033012

TABLE 2. EQUIPMENT SUPPLIED

Item Quantity Purpose Kepco P/N

Output Power cable
(1.5 ft.)

Digital Control (Bitbus)
Cable (3 ft)

Protection Cable
(1 ft.)

Series Control cable
(1.5 ft.)

Protection - OUT Termi­nation (Slave)

Protection - IN Termina­tion (Master)

Chassis Ground Cable 2 Connects chassis ground terminals of all units. 118-1272

Ground Cable mounting
hardware

Output Sense Cable 2 Connects Output sense terminal to Common sense terminal of next unit. 118-1271

Instruction Manual 1 Lists material supplied and specifications for multiple unit combination. 228-1525

3 sets Each set consists of eight parts, mounted in the following order: No. 10 star lock-

Connects the OUTPUT terminal of Master to the COMMON terminal of Slave #1 and

2

the OUTPUT terminal of Slave #1 to the COMMON terminal of Slave #2.

Provides communication between master and two slaves.

1

Provides interlock protection signals required for multiple unit operation.

2

Provides control signals required for series operation.

2

Provides proper termination for the slave connection to the Protection Cable.

1

Provides proper termination for the master connection to the Protection Cable.

1

washer P/N 103-0106 (at chassis), No. 10 flat washer P/N 103-0031, No. 10 split
lockwasher P/N 103-0033, 10-32X3/8 nut P/N 102-0008, No. 10 flat washer P/N 103­0031, [lug(s) from ground cable], No. 10 flat washer P/N 103-0031, No. 10 split lock­washer P/N 103-0033, and 10-32X3/8 nut P/N 102-0008.

118-1112

118-1148

118-1126

118-1120

195-0108

195-0107

(See

Purpose

at left for

part

numbers)

TABLE 3. MODEL PARAMETERS FOR THREE (3) IDENTICAL BOP 1000 WATT UNITS (SERIES)

(3) Identical Models

(Series)

BOP 6-125MG ±18V d-c ±125A d-c 1.8 12.5

BOP 10-75MG ±30V d-c ±75A d-c 3.0 7.5

BOP 20-50MG ±60V d-c ±50A d-c 6.0 5.0

BOP 25-40MG ±75V d-c ±40A d-c 7.5 4.0

BOP 36-28MG ±108V d-c ±28A d-c 10.8 2.8

BOP 50-20MG ±150V d-c ±20A d-c 15.0 2.0

BOP 72-14MG ±216V d-c ±14A d-c 21.6 1.4

BOP 100-10MG ±300V d-c ±10A d-c 30.0 1.0

d-c Output Range Closed Loop Gain

E

O Max

I

O Max

Voltage Channel

(V/V)

Current Channel

(A/V)

TABLE 4. GENERAL SPECIFICATIONS FOR THREE (3) IDENTICAL BOP 1000 WATT UNITS (SERIES)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 28.5A a-c maximum

264 Va-c

Leakage current 10.5mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

Programming
resolution / accuracy

Readback
resolution / accuracy

Voltage 14 bits / 0.2% 2% accuracy for Ext Ref Level. Unit gain adjustable between 0 and

Current 14 bits / 0.5%

Voltage Limit 12 bits / 0.5%

Current Limit 12 bits / 0.5%

Voltage 16 bits / 0.2% main or limit channel

Current 16 bits / 0.5% main or limit channel

19.2A a-c

maximum

/10 (voltage) or I

E

ONOM

ONOM

/10 (current).

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1525 REV 3 033012