KEPCO KIT 219-0443 User Manual

INSTRUCTION SHEET

KEPCO

An ISO 9001 Company.

CABLE

KIT

219-0443

CABLE KIT NO. 219-0443

BOP 1000W MODELS (2) IN SERIES

I. DESCRIPTION.

This kit contains the cables and terminations required to operate two identical 1000 Watt BOP High Power mod­els in series, effectively doubling the output voltage capacity. Only identical models may be configured to operate
in series.

This kit can be used with all 1000W BOP models that have revison levels as shown in Table 1. Earlier models that

!

have been upgraded to permit multiple unit configurations must include the letter “A” following the revison num­ber.CAUTION: Failure to install the ground cables supplied can result in damage to the power supply.

Refer to the associated technical manual supplied with the High Power BOP power supply for all instructions
regarding installation and operation of multiple units in series.

TABLE 1. REVISION LEVELS APPLICABLE TO THIS KIT

Model Revision

BOP 6-125MG All All

BOP 10-75MG 5 or higher 3A or 4A

BOP 20-50MG 8 or higher 5A, 6A or 7A

BOP 25-40MG All All

BOP 36-28MG 11 or higher 8A, 9A or 10A

BOP 50-20MG 7 or higher 5A or 6A

BOP 72-14MG 7 or higher 6A

BOP 100-10MG 6 or higher 2A or 4A

Revisions for Upgraded Units

(Must include “A”)

II. SPECIFICATIONS

Table 3 lists the model parameters unique to a series combination of two identical 1000W BOP Power Supplies.
Table 4 lists the general specifications for the series combinations listed in Table 3. For specifications not listed in
Table 3, refer to the General Specifications provided in the associated technical manual supplied with each
1000W BOP power supply

Item Quantity Purpose

Output Power cable

(1.5 ft.)

Digital Control (Bitbus)

Cable (1 ft)

Protection Cable

(1 ft.)

Series Control cable

(1.5 ft.)

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

©2012, KEPCO, INC
Data subject to change without notice

TABLE 2. EQUIPMENT SUPPLIED

Kepco Part

Number

1

1 Provides communication between master and slave. 118-1108

1

1 Provides control signals required for series operation. 118-1120

http://www.kepcopower.com  email: [e-mail]

Connects the OUTPUT terminal of Master to the COMMON
terminal of Slave #1.

Provides interlock protection signals required for multiple unit
operation.

228-1486 REV 2 033012

118- 1112

118-1126

TABLE 2. EQUIPMENT SUPPLIED (CONTINUED)

Item Quantity Purpose

Protection - OUT

Termination (Slave)

Protection - IN

Termination (Master)

1

1

Provides proper termination for the slave connection to the
Protection Cable.

Provides proper termination for the master connection to the
Protection Cable.

Chassis Ground Cable 1 Connects chassis ground terminals of all units.

Ground Cable mounting

hardware

2 sets Each set consists of eight parts, mounted in the following order:

No. 10 star lockwasher P/N 103-0106 (at chassis), No. 10 flat
washer P/N 103-0031, No. 10 split lockwasher P/N 103-0033, 10­32X3/8 nut P/N 102-0008, No. 10 flat washer P/N 103-0031,
[lug(s) from ground cable], No. 10 flat washer P/N 103-0031, No.
10 split lockwasher P/N 103-0033, and 10-32X3/8 nut P/N 102-

0008.

Output Sense Cable 1

Instruction Manual 1

Connects Output sense terminal to Common sense terminal of
next unit.

Lists material supplied and specifications for multiple unit
combination.

TABLE 3. MODEL PARAMETERS FOR TWO (2) IDENTICAL BOP 1000 WATT UNITS (SERIES)

(2) Identical Models

(Series)

BOP 6-125MG ±12V d-c ±125A d-c 1.2 12.5

d-c Output Range Closed Loop Gain

E

O Max

I

O Max

Voltage Channel

(V/V)

Current Channel

(A/V)

Kepco Part

Number

195-0108

195-0107

118-1272

(See

Purpose

at left for part

numbers)

118-1271

228-1486

BOP 10-75MG ±20V d-c ±75A d-c 2.0 7.5

BOP 20-50MG ±40V d-c ±50A d-c 4.0 5.0

BOP 25-40MG ±50V d-c ±40A d-c 5.0 4.0

BOP 36-28MG ±72V d-c ±28A d-c 7.2 2.8

BOP 50-20MG ±100V d-c ±20A d-c 10.0 2.0

BOP 72-14MG ±144V d-c ±14A d-c 14.4 1.4

BOP 100-10MG ±200V d-c ±10A d-c 20.0 1.0

TABLE 4. GENERAL SPECIFICATIONS FOR TWO (2) IDENTICAL BOP 1000 WATT UNITS (SERIES)

SPECIFICATION RATING/DESCRIPTION CONDITION

INPUT CHARACTERISTICS

Current 176 Va-c 19A a-c maximum

264 Va-c 12.8A a-c maximum

Leakage current 7mA a-c 230V a-c, 47-63 Hz

OUTPUT CHARACTERISTICS

Programming
resolution / accuracy

Readback
resolution / accuracy

Voltage 14 bits / 0.2% 2% accuracy for Ext Ref Level. Unit gain

Current 14 bits / 0.5%

adjustable between 0 and E
(voltage) or I

ONOM

/10 (current).

ONOM

Voltage Limit 12 bits / 0.5%

Current Limit 12 bits / 0.5%

Voltage 16 bits / 0.2% main or limit channel

Current 16 bits / 0.5% main or limit channel

/10

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]

FAX [phone]  email: [e-mail]

2 228-1486 REV 2 033012