KEPCO CS06 User Manual

INSTRUCTION MANUAL

KEPCO

An ISO 9001 Company.

CS 06

CHASSIS SLIDES MODEL CS 06

1. DESCRIPTION

Chassis Slides Model CS 06 contains the components required to install a pair of chassis slides on Kepco EL Series
Electronic Loads.

CAUTION: Use of components not provided herein may damage the unit and void the warranty.

2. INSTALLATION OF CHASSIS SLIDES

2.1 MATERIAL REQUIRED (SEE TABLE 1.)

TABLE 1. MATERIAL SUPPLIED

MATERIAL QUANTITY

One pair of slides (includes cabinet, intermediate and chassis
sections), Kepco P/N 108-0475

* End bracket 2

1

* Bar Nut 6

* Machine Screw, 10-32 X 1/2 in. long, Phillips head, Flat head 4

* Machine Screw, 10-32 X 3/8 in. long, Phillips head, Pan Head 12

* Machine Screw 10-32 x 1/4 in. long, PHPH, black, zinc oxide
(Kepco P/N 101-0531) *

CS 06 Instruction Sheet 228-1734 1

* Included with P/N 108-0475

7

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

http://www.kepcopower.com  email: [e-mail]

©2011, KEPCO, INC 1
Data subject to change without notice 228-1734 REV 1

2.2 PROCEDURE (SEE FIGURES 2, 3 AND 4.)

1. The slides are shipped pre-assembled. Press lock button and separate chassis section of each slide from
intermediate section (See Figure 1).

CABINET
SECTION

INTERMEDIATE
SECTION

CHASSIS
SECTION

PRESS LOCK BUTTON TO

3043551

SEPARATE CABINET SECTION
FROM INTERMEDIATE SECTION.

FIGURE 1. SEPARATE CHASSIS SECTION

2. Attach two chassis sections of slide to each side of Electronic Load using seven black screws (P/N 101-

0531): four on one side and three on the other side (see Figure 2).

CAUTION: Using screws other than those specified will damage

!

the unit and void the warranty.

MACHINE SCREW (4),
10-32 x 1/4 PH PAN HEAD
(KEPCO P/N 101-0531)

3043550

CHASSIS
SECTION

EL SERIES
ELECTRONIC LOAD

CHASSIS
SECTION

MACHINE SCREW (5),
10-32 x 1/4 PH PAN HEAD
(KEPCO P/N 101-0531)

FIGURE 2. INSTALLING CHASSIS SECTION ON ELECTRONIC LOAD CHASSIS

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

http://www.kepcopower.com  email: [e-mail]

2 228-1734 REV 1 061711

3. Attach two end brackets to the two cabinet sections of slides using four screws and two bar nuts (see Figure

3). Use appropriate holes to accommodate cabinet.

4. Attach two front cabinet rails to two cabinet sections using four pan head screws and two bar nuts. For flush
mounting use four flat head screws instead of the pan head screws.

5. Attach two rear cabinet rails to two cabinet sections using four pan head screws and two bar nuts.

COUNTERSINK HOLES

OF CABINET MOUNTING

RAIL FOR FLUSH MOUNTING

MACHINE SCREW (2),

10-32 x 1/2 PH

FLAT HEAD

FLUSH MOUNTING

MACHINE SCREW (3),

10-32 x 1/2 PH

PAN HEAD

BAR NUT

CABINET MOUNTING RAIL,
REAR, LEFT SIDE
(NOT SUPPLIED)

USE APPROPRIATE HOLES
TO ACCOMMODATE CABINET

END
BRACKET

MACHINE SCREW (3),
10-32 x 3/8 PH
PAN HEAD

MACHINE SCREW (2),

10-32 x 3/8 PH

PAN HEAD

0.31 IN. CLEARANCE REQUIRED
BEHIND CABINET SECTION TO
ALLOW LOCK BUTTON TO RELEASE.

CABINET
SECTION

CABINET MOUNTING RAIL
FRONT, LEFT SIDE
(NOT SUPPLIED)
FOR FLUSH MOUNTING,

3043548

SEE DETAIL

FIGURE 3. ATTACHING END BRACKETS AND CABINET MOUNTING RAILS TO CABINET SECTION

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

061711 228-1734 REV 1 3

http://www.kepcopower.com  email: [e-mail]

6. Attach front and rear cabinet mounting rails (with cabinet and intermediate sections of slide attached) to the
cabinet rail (attaching hardware not supplied) (see Figure 4).

WARNING!

!

The load is very heavy (80 - 90 pounds). Exercise care when lifting, mounting or
otherwise handling this product. It is recommended that two or more persons
handle the electronic load.

7. Insert Electronic Load into rack by sliding chassis-mounted slide section into the cabinet-mounted intermedi­ate section).

WARNING!

!

Do not lean on unit when fully extended. Weight added to the fully extended unit in
excess of 35 lbs can cause the slide to fail and the unit to fall.

REAR

REAR
CABINET
MOUNTING
RAIL

CABINET
RAIL

EL SERIES
ELECTRONIC
LOAD

3043549

FRONT
CABINET
RAIL

FRONT
CABINET
MOUNTING
RAIL

CHASSIS
SECTION

CABINET
SECTION

INTERMEDIATE
SECTION

FIGURE 4. ATTACHING CABINET SECTION TO RAIL

KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A.  TEL [phone]  FAX [phone]

http://www.kepcopower.com  email: [e-mail]

4 228-1734 REV 1 061711