Kenwood VR-8060 User Manual

AUDIO VIDEO SURROUND RECEIVER

VR-8060

INSTRUCTION MANUAL

KENWOOD CORPORATION

About the supplied remote control

Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc.). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations.

For the U.S.A.

Plus opt in to receive e-mail updates and other offers when you register at our web site.

B60-5470-00 00 MA (K, P) 0404

Before applying the power

Caution : Read this page carefully to ensure safe

operation.

Units are designed for operation as follows.

U.S.A. and Canada ........................................... AC 120 V only

Australia ........................................................... AC 240 V only

Europe and U.K ................................................ AC 230 V only

China and Russia ............................................. AC 220 V only

Other countries ............ AC 110-120 / 220-240 V switchable

Maintenance of the unit

When the front panel or case becomes dirty, wipe with a soft, dry cloth. Do not use thinner, benzine, alcohol, etc. for these agents may cause discoloration.

In regard to contact cleaner

Do not use contact cleaners because it could cause a malfunction. Be specially careful not to use contact cleaners containing oil, for they may deform the plastic component.

Safety precautions

WARNING :

TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

How to use this manual

This manual is divided into four sections, Preparations, Operations, Remote Control, and Additional Information.

Preparations

Shows you how to connect your audio and video components to the receiver and prepare the surround processor. Since this receiver works with all your audio and video components, we will guide you in setting up your system to be as easy as possible.

Operations

Shows you how to operate the various functions available on the receiver.

Remote Control

Shows you how to operate other components using the remote control, as well as a detailed explanation of all remote control operations. Once you have registered your components with the proper setup codes, you’ll be able to operate both this receiver and your other AV components (TV, VCR, DVD player, CD player, etc.) using the remote control supplied with this receiver.

Additional Information

Shows you additional information such as “In case of difficulty” (troubleshooting) and “Specifications”.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

Before applying the power

Contents

Caution : Read the pages marked carefully to ensure

Preparations

safe operation.

Before applying the power ...................................................... 2

Safety precautions..................................................................... 2

How to use this manual ............................................................ 2

Unpacking ..................................................................................3

Preparing the remote control .................................................... 4

Special features ......................................................................... 5

Names and functions of parts ................................................. 6

Main Unit ................................................................................... 6

Remote control unit ........................................................................

Setting up the system ........................................ 8

Connecting the terminals .................................. 9

Connecting audio components ........................ 10

Connecting video components ........................ 11

Digital connections .......................................... 12

Connecting video components

(COMPONENT VIDEO) .................................... 13

Connecting a DVD player (6-channel input) ..... 14

Connecting the speakers .................................15

Connecting to the AV AUX jacks ..................... 16

Connecting the antennas ................................. 16

Preparing for surround sound ....................... 17

Speaker settings .............................................. 17

Normal playback.............................................. 20

Preparing for playback ..................................... 20

Listening to a source component .................... 20

Adjusting the sound ......................................... 21

Recording .......................................................... 23

Recording audio (analog sources) ................... 23

Recording video ............................................... 23

Operations

Recording audio (digital sources) .................... 23

Listening to radio broadcasts ....................... 24

Tuning radio stations ....................................... 24

Presetting radio stations manually .................. 24

Receiving preset stations ................................ 25

Receiving preset stations in order (P.CALL) ... 25

Ambience effects ............................................. 26

Surround modes .............................................. 26

Surround play ................................................... 28

DVD 6-channel playback .................................. 30

Convenient functions ....................................... 30

Unpacking

Unpack the unit carefully and make sure that all accessories are present.

FM indoor antenna (1) AM loop antenna (1)

Remote control unit (1) Batteries (R6/AA) (2)

RC-R0822

If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer immediately. If the unit was shipped to you directly, notify your shipper immediately. Kenwood recommends that you retain the original carton and packing materials in case you need to move or ship the unit in the future.

Keep this manual handy for future reference.

Remote Control

Additional

Information

Basic remote control operations for other

components ....................................................... 33

Registering setup codes for other

components ..................................................... 33

Searching for your codes ................................. 33

Checking the codes ......................................... 34

Re-assigning device keys ................................ 34

Operating other components .......................... 34

Setup code chart .............................................. 35

CASSETTE deck, CD player & MD recorder

operations ........................................................ 39

Other components’ operations ....................... 40

In case of difficulty .......................................... 42

Specifications .................................................. 44

Before applying the power

Preparing the remote control

Loading the batteries

1 Remove the cover. 2 Insert the batteries.

3 Close the cover.

• Insert two AA-size (R6) batteries as indicated by the polarity markings.

Operation

When the STANDBY indicator is lit, the power turns ON when you press the POWER RCVR ON, press the key you want to operate.

Operating range (Approx.)

key on the remote control. When the power comes

Remote sensor

6 m

For the U.S.A.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – – Reorient or relocate the receiving antenna. – – Increase the separation between the equipment and receiver. – – Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– – Consult the dealer or an experienced radio / TV technician for

help.

For the U.S.A.

Note to CATV system installer

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

POWER RCVR

Infrared ray system

• When pressing more than one remote control key successively, press the keys securely by leaving an interval of 1 second or more between keys.

Notes

1. The supplied batteries may have shorter lives than ordinary batteries

due to use during operation checks.

2. When the remote-controllable distance gets shorter than before,

replace both batteries with new ones.

3. Placing the remote sensor in direct sunlight, or in direct light from a

high frequency fluorescent lamp may cause a malfunction. In such a case, change the location of the system installation to prevent malfunction.

As an ENERGY STAR® Partner, Kenwood

Corporation has determined that this

product meets the

guidelines for energy efficiency. This

product can save energy. Saving energy

reduces air pollution and lowers utility bills.

ENERGY STAR

Before applying the power

Special features

True home theater sound

This receiver incorporates a wide variety of surround modes to bring you maximum enjoyment from your video software. Select a surround mode according to your equipment or the software you are going to play and enjoy! §

Neo:6

Neo:6 is a new technology which was developed by DTS. It can produce high grade 6 channels surround with an astonishing fidelity from 2 channels content. Neo:6 has 2 mode, "CINEMA" mode is for movie playback and "MUSIC" mode is for music playback.

Dolby Digital and Dolby Digital EX

The DOLBY DIGITAL mode lets you enjoy full digital surround from software processed in the Dolby Digital format. Dolby Digital provides up to 5.1 channels of independent digital audio for better sound quality and more powerful presence than conventional Dolby Surround. As for Dolby Digital EX, it creates six full-bandwidth output channels from the 5.1 channel sources. This is done using a matrix decoder that derives three surround channels from the two in the original recording. For best results, Dolby Digital EX should be used with movie soundtracks recorded with Dolby Digital Surround EX.

Dolby PRO LOGIC IIx and Dolby PRO LOGIC

DOLBY PRO LOGIC II, whilst totally compatible with its predecessor PRO LOGIC, provides greater advantages in surround sound. It allows user to enjoy the conventional stereo or Dolby Surround with a convincing “5.1 like” presentation. PRO LOGIC II offers special features for controlling the overall spatial, dimensionality and frontal sound field imaging. PRO LOGIC II produces an impressive surround sound from video software marked dimensional space from music CD. When listening to music, you will be able to enjoy the experience of sheer STEREO surround sound. DOLBY PRO LOGIC IIx enhanced DOLBY PRO LOGIC II’s features. It creates 6.1 channel and 7.1 channel surround sound from stereo or

5.1 channel signals. This feature provides you an astonishing ambience effect which makes you feel you are surrounded by natural sound. Especially 7.1 channel surround sound can produce real back sound from Surround Back speakers.

and three-

DTS and DTS-ES

DTS (Digital Theater System) is a 5.1 channel digital audio format that provides five full spectrum channels and one low-frequency (subwoofer) channel for unprecedented clarity, optimum channel separation and a (wide) dynamic range. DTS-ES (Extended Surround) presents 6.1 channels surround system with additional Surround Back channel which evolved from the conventional 5.1 channels surround system. DTS-ES format that was recorded in DVD, CD or LD comprises of two modes. DTS-ES Discrete

6.1 produce the discrete surround back which is completely independent and DTS-ES Matrix 6.1 produces the surround back which synthesised within the left and right surround channels using matrix technology. DTS-ES has perfect compatibility with the conventional 5.1 channels surround system. 6.1 channels surround with an additional surround back presents a more natural presence and surround effects by increasing the impression of the sound image from back. Important: When a DTS disc is played on a CD, LD or DVD player, noise may be output from the analog output. It is recommended that you connect the digital output of the player to the digital input of this unit.

DSP surround modes

The DSP (Digital Signal Processor) used for this receiver incorporates a variety of high quality adjustable sound fields, like “ARENA”, “JAZZ CLUB”, “THEATER”, “STADIUM” and “DISCO”. It is compatible with almost any kind of program source.

DVD 6-channel input

If you own a DVD player equipped with 6-channel output, this receiver allows you to obtain the full surround sound impact of DVD source material featuring multi-channel encoding. Since the source signals are digital and each channel is input independently, the resulting ambience is far superior to what can be achieved with conventional surround sound systems.

ACTIVE EQ

ACTIVE EQ mode will produce a more dynamic sound quality in any condition. You can enjoy a more impressive sound effect when ACTIVE EQ is turned on.

SPEAKER EQ

SPEAKER EQ function is to adjust the receiver’s audio output characteristics with the speakers’ characteristics which differs depending on the size of the speakers. When activating the SPEAKER EQ function, you will be able to enjoy a more natural and dynamic sound experience even with small size speakers.

Universal IR (InfraRed) remote control

In addition to the basic receiver, the remote control supplied with this receiver can also operate almost all of your remote controllable audio and video components. Just follow the simple setup procedure to register the components you have connected.

Video up conversion

This receiver can convert the incoming composit video signals to SVideo signal. If your monitor TV has S-Video jacks, it is not necessary to do the composit video connections, just use an S-Video cord to connect the receiver and your monitor TV.

DTS 96/24

DTS 96/24 made it possible to achieve a wide frequency range of over 40 kHz by increasing the sampling frequency to 96 or 88.2 kHz. Moreover, DTS 96/24’s ability of 24 bit resolution offers the same frequency band and dynamic range as 96 kHz/24 bit PCM. DTS 96/24 is, as with conventional DTS Surround, compatible with multi-channels. Therefore, sources recorded using DTS 96/24 technologies can be played in high sampling frequency, multi-channel audio with ordinary DVDs and CDs.

Names and functions of parts

Main unit

*Input channel indicators

Input channel indicators light up according to the incoming audio signals. "S" indicator will light up when the surround component of the audio signals is only 1 channel.

POWER

STANDBY

ON/STANDBY

A SPEAKERS B

PHONES

Speaker indicators

*Input channel indicators

Output channel indicators

MUTE indicator

LFE

SL S SB SR

ACTIVE EQ SPEAKER EQ LOUDNESS DSP STEREO INPUT MODE DIMMER

AB CLIP

DSP

SPEAKER EQ

ACTIVE EQ

MUTE

DOLBY DIGITAL

DTS

LOUDNESS

CLIP indicator

OPTICAL 6CH INPUT

COAXIAL ANALOG 96kHzfs

TUNERPHONOCD/DVDDVD/6CH

MD/TAPEVIDEO 3VIDEO 2VIDEO 1

Input mode indicators

AUTO DETECT

DSP MODE

Display

SETUPTONESOUND

MEMORYAUTOBAND

DTS

MATRIX

DISCRETE

Listen mode indicators

DOLBY DIGITAL

STEREO

PRO LOGIC

LOUDNESS

Frequency display Input display Preset channel display Surround mode display

NEO:6

LISTEN MODEMULTI CONTROL

AUTO MEMORY STEREO

TUNED

S VIDEO VIDEO L-AUDIO-R

AUTO indicator MEMORY indicator

STEREO indicator

TUNED indicator

VOLUME CONTROL

DOWN UP

MUTE

AV AUX

1 POWER ON/STANDBY key &

Use to turn the power ON/STANDBY.

STANDBY indicator

2 A SPEAKERS B keys )

Use to turn the A/B speakers on or off.

3 ACTIVE EQ key ¡

Use to select ACTIVE EQ’s setting.

4 SPEAKER EQ key ¡

Use to select SPEAKER EQ’s setting.

5 Surround LED (lighting-emitting diode)

indicators DSP mode LED indicator ª

Lights when the receiver is in the DSP mode.

SPEAKER EQ mode LED indicator ™

Lights when the receiver is in the SPEAKER EQ mode.

ACTIVE EQ mode LED indicator ™

Lights when the receiver is in the ACTIVE EQ mode.

DOLBY DIGITAL mode LED indicator

Lights when the receiver is in the Dolby Digital mode.

DTS mode LED indicator ª

Lights when the receiver is in the DTS mode.

LOUDNESS LED indicator ¡

Lights when the LOUDNESS is ON.

6 LOUDNESS key ¡

Use to switch the status of LOUDNESS.

7 DSP key •

Use to select any of the DSP mode.

8 STEREO key º

Use to switch the listen mode to STEREO.

9 INPUT MODE key 8

Use to switch between the full auto, digital and analog inputs.

0 DIMMER key

Use to select the REC MODE. £ Use to adjust the brightness of the display.

! VOLUME CONTROL knob ) @ MUTE key ¡

Use to temporarily mute the sound.

# PHONES jack ™

Use for headphone listening.

$ Input Selector keys )

(DVD/6CH, CD/DVD, PHONO, TUNER, VIDEO 1, VIDEO 2, VIDEO 3, MD/TAPE)

Use to select input sources.

% SOUND key º

Use to adjust the sound quality and the ambience effects.

^ BAND key ¢

Use to select the broadcast band.

& AUTO key ¢

Use to select the auto or manual tuning mode.

* TONE key ¡

Use to switch the status of TONE control.

( MEMORY key ¢

Use to store radio stations in the preset memory.

) SETUP key &

Use to select the speakers' settings etc.

keys &

Use for selection adjustments during sound,

set up and preset channel functions.

™ MULTI CONTROL knob &

Use to control a variety of settings.

£ LISTEN MODE knob •

Use to select the listening mode.

¢ AV AUX (S VIDEO, VIDEO, L-AUDIO-R)

jacks ^

∞ AV AUX key ^

Use to switch the input to AV AUX.

Standby mode

While the standby indicator is lit, a small amount of power is supplied to the system to back up the memory. This is called standby mode. Under the condition, the system can be turned ON by remote control unit.

Names and functions of parts

Remote control unit

This remote control unit can be use not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’s setup codes. ﬁ

DVD

TAPE

(

)

™

∞

Mute

§ ¶

• ª

º ⁄ ¤ ‹

ker

›

If the name of a function is different on the receiver and on the remote control, the name of the remote control key in this manual is indicated in parentheses.

ﬁ

£ Page 5/∞ keys

Use to operate other components.

¢ OSD (on screen display) key

Use to operate the DVD component.

Guide key

Use to operate other components.

∞ Menu key

Use to operate other components.

§ Mute key ¡

Use to temporarily mute the sound.

¶ Tone key ¡

Use to switch the status of TONE control.

Sound key º

Use to adjust the sound quality and the ambience effects.

• VOL +/– keys )

Use to adjust the receiver’s volume.

ª Bass Boost key ¡

Use to select the maximum adjustment setting for the low frequency range.

º ÷ key

If VCR is selected, this key functions as record key when it pressed twice sequentially. When in MD or Tape is selected, this key functions as record key.

Top Menu key

Use to operate the DVD component.

Setup key &

Use to select the speakers’ settings etc.

⁄ Loudness key ¡

Use to switch the status of LOUDNESS.

¤ Remote Setup key ‹

Use to register other components.

‹ 7 key

If CD, MD, or TAPE is selected as the input source, this key functions as the stop key.

Auto key ¢

Use to select the auto or manual tuning mode.

› Speaker EQ key ¡

Use to select SPEAKER EQ’s setting.

ﬁ Stereo key º

Use to switch the listen mode to STEREO.

1 Source keys (MD/TAPE, CD/DVD, DVD/6CH,

TUNER,

VID1, VID2, VID3, AV AUX

When press and hold for more than 3 seconds, they are used to select the registered components.

Input Selector keys (MD/TAPE, CD/DVD, DVD/ 6CH, TUNER, VID1, VID2, VID3, AV AUX, PHONO)

When press and release in less than 3 seconds, they are used to select the input sources.

2 SRC (

Use to turn the other source components on or off.

3 Numeric keys ∞

Provide functions identical to those of the original remote control supplied with the component you are controlling.

Multi (multi control) %/ﬁ keys &

Use to control a variety of settings. Use to operate other components.

P.Call @/# keys ∞

Use for selection adjustments during sound, set up and preset channel functions.

Enter key

Use to operate other components.

4 Return key

Use to operate the DVD component.

Exit key

Use to operate other components.

5 Disc Skip key

If CD is selected as the input source, this key functions as the multi-CD player disc skip key.

LAST/A/B key

If TAPE is selected as the input source, this is A and B deck of a double cassette deck. Use to operate other components.

6 Disc Sel. key

Use to operate other components.

Input Sel. key

Use to operate other components.

7 CH +/– keys

Use to select the channels. ¢ / 4 keys If CD, MD and DVD is selected as the input source, these keys function as skip keys.

8 TV Input key

Use when in TV operation.

source

) Power key

, PHONO)

‹

)

DVD

TUNER

VID1

VID2

PHONO

4 5 6

7 8 9 0

! @

+ 10

Return

Disc Sel.

Input Sel.

Tune – Tune +

Dimmer

# $

Listen Mode

6CH

VID3

AV AUX

POWER

RCVR

P. Call

LAST / A/B

Exit

Disc Skip

–

VOL

Input

Mode

Multi

P. Call

Enter

Multi

+ 100

TV Mute

Page

OSD

Guide

Tone

VOL

Sound

–

Bass

TV Input

+–

Boost

Band

Top MenuAuto

Setup

Flip

Info

Loudness

Active

Remote

Setup

DSP

Spea

Stereo

Mode

^ &

9 TV VOL +/– keys

Use to adjust the TV’s volume.

0 1/¡ keys

If CD, MD or Tape is selected as the input source, this key functions as search keys.

Tune –/+ keys ¢

Use to operate the tuner mode.

! 8 key

Use to operate other components.

Dimmer key º

Use to adjust the brightness of the display.

@ 3/8 key

If CD is selected as the input source, this key functions as the play/pause key. If MD or TAPE key is selected as input source, this key functions as the play key.

Band key ¢

Use to select the broadcast band.

# 2 key

If Tape is selected, this key functions as reverse play key.

Info/Flip key

Use to operate other components.

$ Input Mode key 8

Use to switch between the full auto, digital and analog inputs.

% Listen Mode 5/∞ keys •

Use to select the listening mode.

^ DSP Mode key •

Use to select any of the DSP mode.

& Active EQ key ¡

Use to select ACTIVE EQ’s setting.

* LED (lighting-emitting diode) indicator

Blinks to show that signals are being transmitted.

( TV key

Use to select the TV equipment.

) POWER RCVR (

Use to turn the receiver on or off.

¡ TV Power key

Use to turn the TV on or off.

™ +100 key

Use to select the disc number with the multiCD player.

TV mute key

Use to temporarily mute the TV sound.

) key &

receiver

Setting up the system

Make connections as shown in the following pages. When connecting the related system components, be sure to refer to the instruction manuals supplied with the components you are connecting. Do not connect the power cord to a wall outlet until all connections are completed.

Notes

Be sure to insert all connection cords securely. If their connections are

1. imperfect, sound may not be produced or there will be noise inference.

2. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging/unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit.

3. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit.

Analog connections

Audio connections are made using RCA pin cords. These cables transfer stereo audio signal in an “analog” form. This means the audio signal corresponds to the actual audio of two channels. These cables usually have 2 plugs on each end, one red for the right channel and one white for the left channel. These cables are usually packed together with the source unit, or are available at your local electronics retailer.

Microcomputer malfunction

If operation is not possible or an erroneous display appears, even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. w

Memory back up function

Please note that the following items will be deleted from the unit's memory if the power cord is disconnected from the AC outlet for approximately 1 day.

• Power mode

• Input selector settings

• Picture output

• Speaker ON/OFF

• Volume level

• BASS, TREBLE, INPUT level

• TONE ON/OFF

• LOUDNESS ON/OFF

• Dimmer level

• MD/TAPE settings

• Listen mode setting

• Speaker settings

• Distance setting

• Input mode setting

• Sound mode settings

• Broadcast band

• Frequency setting

• Preset stations

• Tuning mode

• ACTIVE EQ mode

• SPEAKER EQ mode

Input mode settings

CD/DVD, VIDEO 2, VIDEO 3 and DVD/6CH inputs each include jacks for digital audio input and analog audio input.

The initial factory settings for audio signal playback for CD/DVD, DVD/6CH, VIDEO 2 and VIDEO 3 are full auto.

After completing connections and turning on the receiver, follow the steps below.

INPUT MODE

Input Selector

1 Use the Input Selector keys to select CD/DVD, VIDEO 2, VIDEO 3

or DVD/6CH.

2 Press the INPUT MODE key.

Each press switches the setting as follows:

In DTS play mode

1 FULL AUTO (digital input, analog input) 2 DIGITAL MANUAL (digital input)

In CD/DVD, VIDEO 2, VIDEO 3 or DVD/6CH play mode

1 FULL AUTO (digital input, analog input) 2 DIGITAL MANUAL (digital input) 3 6CH INPUT (DVD/6CH input) 4 ANALOG (analog input)

Digital input:

Select this setting to play digital signals from a DVD, CD, or LD player.

Analog input:

Select this setting to play analog signals from a cassette deck, VCR, or record player.

Auto detect:

In “FULL AUTO” mode (AUTO DETECT indicator light up), the receiver detects the digital or analog input signals automatically. Priority is given to digital signal during input mode selection. The receiver will select the input mode and listening mode automatically during playback to match the type of input signal (Dolby Digital, PCM, DTS) and the speaker setting. The OPTICAL and COAXIAL indicator on the display will light up when digital signal is detected. If the input signal is analog, the ANALOG indicator will light up. To keep the receiver set to the currently selected listening mode, use the INPUT MODE key to select “DIGITAL MANUAL” (manual sound). However, even when this setting is selected, there may be cases in which the listening mode is selected automatically to match a Dolby Digital source signal depending on the combination of listening mode and source signal. At DIGITAL MANUAL, if the audio reproduction stops in the middle due to change in the input signals, etc. press the LISTEN MODE Knob. If the INPUT MODE key is pressed quickly, sound may not be produced. Press the INPUT MODE key again.

LISTEN MODE

Setting up the system

Connecting the terminals

1 Strip coating. 2 Loosen.

3 Insert. 4 Secure.

1 Strip coating. 2 Push the lever.

3 Insert the cord. 4 Return the lever.

Connection of banana plugs

1 Secure. 2 Insert.

Speaker placement

Center Speaker

Front Speakers (L, R)

Surround Speakers (L, R)

*Surround Back

Left Speaker

*For Surround Back speaker, you may place either two Surround Back

speakers (Surround Back Left Speaker and Surround Back Right Speaker) for 7.1 channel surround sound system or one Surround Back Speaker for 6.1 channel surround sound system.

Front (Left and Right) Speakers

Place at the front left and right of the listening position. Front Speakers are required for all surround modes.

Center Speaker

Place front and center. This speaker stabilizes the sound image and helps recreate sound motion. Required for surround playback.

Surround (Left and Right) Speakers

Place at the direct left and right, or slightly behind, the listening position at even heights, approximately 1 meter above the ears of the listeners. These speakers recreate sound motion and atmosphere. Required for surround playback.

Subwoofer

Reproduces powerful deep bass sounds.

Surround Back Speaker/s

Place the speaker/s directly at the rear of the listening position. The optimum position depends mainly on the room condition.

Subwoofer

Listening position

*Surround Back

Right Speaker

*Surround Back Speaker

• Sound will not be heard if the speaker terminal is not fully secured.

• Never short circuit the + and – speaker cords.

• If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly.

Speaker impedance

After confirming the speaker impedance indications printed on the rear panel of the receiver, connect speakers with matching impedance ratings. Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or damage to the speakers or receiver.

• Although the ideal surround system consists of all the speakers listed above, if you don't have a Center speaker or a Subwoofer, you can divide those signals between the available speakers in the speaker settings steps to obtain the best possible surround reproduction from the speakers you have available. &

Setting up the system

Connecting audio components

PHONO

IN IN

CD/DVD MD/TAPE

To AC wall outlet

REC OUT PLAY IN

OUT

Cassette Deck or MD Recorder

OUT

CD Player or DVD Player

Moving coil (MC) cartridge record player cannot be used directly

OUT

from the receiver unit. It can only be used when another equalizer amplifier is connected.

Record Player

CAUTION

Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard.

• Do not place any object impairing heat radiation onto the top of the unit.

• Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.

Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm

Setting up the system

Connecting video components

OUT

VIDEOINVIDEO

S VIDEO Jacks

VIDEO

S VIDEO

OUT

VIDEO

VIDEOINVIDEO

DVD

S VIDEO

VIDEO

MONITOR

S VIDEO

VIDEO

OUT

S VIDEO

VIDEO

S VIDEO

OUT

S VIDEO

VIDEO

(DVD) (MONITOR)

VIDEO 1 VIDEO 2 VIDEO 3

PLAY INPLAY INPLAY INREC OUT

About the S VIDEO Jacks

S VIDEO

OUT

Use the S VIDEO Jacks to make connections to video components with S VIDEO IN/OUT Jacks.

If you use the S VIDEO jacks

•

to connect your video playback components, be sure to use the S VIDEO jacks when connecting your monitor and video recording components.

Monitor TV

VIDEO IN

OUT

Video

OUT

Video

Video deck

IN Video

DVD Player or LD Player

OUT Audio

OUT

Audio

OUT

Audio

A video component with digital audio outputs should be connected to the VIDEO 2 or VIDEO 3 jacks.

Setting up the system

Digital connections

The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. 8

VIDEO

DVD/ 6CH

COAXIAL

DIGITAL

OUT

(AUDIO)

RF digital demodulator (Commercially available)

COAXIAL OPTICAL OPTICAL

DIGITAL IN

Optical fiber

VIDEO 3

cable

OPTICAL

MONITORCD/DVD

DIGITAL OUT

Optical fiber cable

OPTICAL DIGITAL

IN (AUDIO)

Optical fiber cable

OPTICAL DIGITAL

OUT (AUDIO)

OPTICAL DIGITAL

OUT (AUDIO)

COAXIAL DIGITAL

OUT (AUDIO)

MD Recorder

Component with DTS, Dolby Digital, or PCM OPTICAL DIGITAL OUT

Connect the video signal and digital audio signals to the VIDEO 3 jacks. (See “Connecting video components”.) !

CD Player or DVD Player

Component with DTS, Dolby Digital, or PCM COAXIAL DIGITAL OUT

Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) !

DOLBY DIGITAL RF

OUT (AUDIO)

PCM OUT

LD Player

To connect an LD player with a DIGITAL RF OUT, connect the LD player to the RF digital demodulator (Commercially available). Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver. Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See “Connecting video components”.)

Setting up the system

Connecting video components (COMPONENT VIDEO)

If you have connected the receiver to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEO jacks.

VIDEO

3 IN

DVD

COMPONENT VIDEO

VIDEO 2 IN

CRCB

MONITOR OUT

CRCB

Monitor TV (with component jacks)

CR IN CB IN

Y IN

Video Recorder, DVD Recorder, Satellite Cable Tuner & Game Player (with component jacks)

CR OUT CB OUT

Y OUT

DVD Player (with component jacks)

CR OUT CB OUT

Y OUT

Video Recorder, DVD Recorder, Satellite Cable Tuner & Game

CR OUT

Player (with component jacks)

CB OUT

Y OUT

When connecting the TV to the COMPONENT jacks, be sure to connect all the other components to the COMPONENT jacks.

Setting up the system

Connecting a DVD player (6-channel input)

If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 8

OUT

VIDEOINVIDEO

VIDEO

VIDEOINVIDEO

DVD

MONITOR

VIDEO

OUT

COAXIAL OPTICAL OPTICAL

VIDEO

DVD/ 6CH

DIGITAL IN

S VIDEO

VIDEO

PLAY IN

VIDEO 2 VIDEO 3

FRONT

S VIDEO

VIDEO

DVD

VIDEO 3

MONITOR

SURROUND

DVD/6CH INPUT

OPTICAL

MONITORCD/DVD

DIGITAL OUT

S VIDEO

OUT

VIDEO

OUT

CENTER

SUB

WOOFER

VIDEO OUT

COAXIAL

DIGITAL OUT

(AUDIO)

DVD Player

FRONT OUT L/R

S VIDEO OUT

SURROUND OUT L/R

CENTER OUT

SUBWOOFER OUT

S VIDEO cord

+ 30 hidden pages