Photo is TM-241A. * Refer to parts list on page 12.
CONTENTS
| CIRCUIT DESCRIPTION | 2 |
|---|---|
| DESCRIPTION OF COMPONENTS | 9 |
| PARTS LIST | 12 |
| EXPLODED VIEW | |
| PACKING | |
| ADJUSTMENT | 25 |
| PC BOARD VIEWS/CIRCUIT DIAGRAM | |
| LCD ASS'Y (B38-0330-05) | |
| PLL (X58-3470-00) | |
| APC (X59-3130-00) | 32 |
| MIC AMP (X59-3610-00) | 32 |
| TX-RX UNIT (X57-369X-XX) | |
e.
| SCHEMATIC DIAGRAM |
|---|
| TERMINAL FUNCTIONS |
| BLOCK DIAGRAM |
| LEVEL DIAGRAM |
| DRU-1 (DIGITAL RECORDING UNIT)43 |
| DTU-2 (DTMF UNIT)51 |
| MC-44 (MULTI FUNCTION MICROPHONE)54 |
| MC-44DM/MC-44DME (MULTI FUNCTION |
| MICROPHONE WITH AUTOPATCH)53 |
| MC-44E (MULTI FUNCTION MICROPHONE)55 |
| TSU-6 (CTCSS UNIT) |
| SPECIFICATIONSBACK COVER |
CIRCUIT DESCRIPTION
| TM-241A | TM-241E | |||
|---|---|---|---|---|
| K,P | М | M2 | E | E2 |
| 0-11 | 0-21 | 0-22 | 2-71 | 2-72 |
|
K,P
0-11 |
TM-241A
K,P M 0-11 0-21 |
TM-241A K,P M M2 0-11 0-21 0-22 | TM-241A TM-241A K,P M M2 E 0-11 0-21 0-22 2-71 | |
Table 1
Circuit Configuration By Frequency
The TM-241A/E incorporates a PLL synthesizer which uses a digital VFO to allow any channel step of 5, 10, 12.5, 15, 20, or 25 kHz to be selected (See Figure 1).
The receiving system utilizes double-conversion techniques. That is, an incoming signal is mixed down to the 1st intermediate frequency (IF) of 10.7 MHz, using a 1st local oscillator frequency of from 133.300 to 135.295 MHz ( E,M ), 125.300 to 163.295 MHz ( K,P,E2,M2 ). The 1st IF signal is then mixed with the 2nd local oscillator frequency of 12.8 MHz to generate the 2nd IF of 455 kHz.
The transmitting system consists of a PLL circuit which allows direct modulation and direct frequency division. Signals from the PLL circuit are amplified by a linear amplifier for transmission.
Fig. 1 Frequency configuration
Receiving System
Overview
Incoming signals from the antenna pass through a low-pass filter in the final block of the transmitter system, and are switched to the front-end of the receiver system via a receive/transmit switching diode.
The signals are then passed through an antenna matching coil, where the high-frequency components are amplified by a GaAs FET. The signals are then fed into a three-stage bandpass filter that uses vari-cap tuning to reject unwanted signal components, and is fed
to the 1st mixer. The 1st mixer uses the N-channel MOS FET that are used in the RF stage to obtain better twosignal characteristics. The 1st mixer mixes the signal with the 1st local oscillator frequency and converts it to the 1st IF (10.7MHz). The signal then passes through two monolithic crystal filters (MCFs) to remove unnecessary near-by frequency components. The signal from the MCFs is used as the 1st IF signal.
The 1st IF signal is amplified and fed into IC1 (KCD04) in the FM IF HIC. The IF signal is then mixed with the 2nd local oscillator frequency of 10.245 MHz to generate the 2nd IF of 455 kHz. The 455 kHz signal is then passed through a six element ceramic filter (CFWM455F), and fed back into IC1 for additional amplification. The output signal from the IC1 is then fed into a power asmplifier via the audio volume control for application to the speaker.
S-meter circuit
S-meter control voltage from IC1 (KCD04) in the FM IF HIC is fed into the control unit. The CPU converters the voltage from an analog to digital signal in order to operate the LCD bar meter.
| ltem | Rating | |||
|---|---|---|---|---|
| Nominal center frequency (fo) | 10.7MHz | |||
| Pass band width | ±7.5kHz or less at 3dB | |||
| Attenuation band width |
±25kHz or less at 40dB
±45kHz or less at 60dB |
|||
| Ripple | 1.0dB or less | |||
| Insertion loss | 1.5dB or less | |||
| Guaranteed attenuation |
70dB or more within ±1MHz
(Spurious : 40dB or more at fo - fo + 500kHz) 80dB or more at fo - (900 - 920kHz) |
|||
| Terminating impedance | 3kΩ/0pF | |||
| ltem | Rating |
|---|---|
| Nominal center frequency | 455kHz ± 1kHz |
| 6dB bandwidth | ±6kHz or more (from 455kHz) |
| 50dB bandwidth | ±12.5kHz or less (from 455kHz) |
|
Ripple
(within ±4kHz of 455kHz) |
3dB or less |
| Insertion loss | 6dB or less |
|
Guaranteed attenuation
(within ±100kHz of 455kHz) |
35dB or more |
| I/O matching impedance | 2.0kΩ |
Table 2 MCF (L71-0228-05) (TX-RX unit XF1)
Table 3 Ceramic filter CFWM455F (L72-0372-05) (TX-RX unit CF1)
Fig. 2 Front-end section (vari-cap tuning)
TM-241A/E
CIRCUIT DESCRIPTION
Transmitting System
Overview
The transmitter produces the target frequency thru the use of direct FM-modulation via a varactor diode.
Modulation circuit
Audio signals from the microphone are fed into the mic amplifier unit for amplification by the first transistor amplifier, and then into two operational amplifiers. The operational amplifiers form a splatter filter for preemphasis, amplification, limiting, and removal of unnecessary high-frequency components.
The FM modulation circuit directly FM-modulates the VCO signals, using a varactor diode.
Pre-amplifier stage circuit
Signals from the VCO are applied to the drive HIC IC8 (KCB05). The amplifier always operates in a linear mode so that signals can be amplified without degradation. Additionally, the amplifier is designed to cover a wide range of frequencies and can produce stable output without adjustment. The APC (Automatic Power Control) controls collector voltage from the last stage of the pre-amplifier.
Power amplifier circuit
The drive signal is amplified to the required level by the power module. The TM-241 A/E uses a large heat sink for efficient heat dissipation.
· APC circuit
The APC circuit for automatic transmit output control detects part of the power module output, and amplifies it to provide a control voltage for output control. The output control voltage is in inverse proportion to the output from the power module, so it is maintained at the same level.
| (Tc = | 25°C | |||
|---|---|---|---|---|
| ltem | Symbol | Condition | Rating | Unit |
| Operating voltage | Vcc | 16 | V | |
| Control voltage | VCON | 16 | V | |
| Current consumption | IT | 14 | A | |
| Input power | Pi | 600 | mW | |
| Output power | Po |
12.5V < Vcc ≤ 16V, VcoN ≤ 12.5V
Pi = 0 ~ 500mW, Zg = ZL = 50Ω |
65 | W |
| Operating case temperature | Tc(opr) | -30 ~ +100 | °C | |
| Storage temperature | Tstg | -40 ~ +110 | °C |
Table 4 Power module S-AV17 maximum ratings (IC301)
CIRCUIT DESCRIPTION
PLL Synthesizer Unit
Figure 4 is the PLL and VCO block diagram. In the TM-241 A/E, the PLL system is implemented as a subunit which is divided into the upper VCO and lower PLL blocks. The sub-unit is shielded to prevent external interference.
There are two reference frequencies, 6.25kHz and 5 kHz, available to allow 5, 10, 12.5, 15, or 25 kHz-step operation. The 6.25kHz is obtained by dividing the reference oscillator frequency of 12.8MHz by 2048, and the 5kHz is obtained by dividing it by 2560. The VCO directly generates the dial frequency. This dial frequency is amplified once and then fed into a pulse swallow-type PLL IC for frequency division and phase comparison, in order to lock the frequency.
The PLL system is locked without switching between transmit mode and receive mode. By using a signal ("H" in transmit mode) from pin 11 of the PLL IC (M54959FP), the LPF is deactivated-activated by Q52 and Q53 only for the moment when the TM-241 A/E enters transmit mode. This helps produce lock more rapidly than previous methods.
In 144MHz mode, fvco (RX) is calculated by the folowing formula:
fvco = (144 + 10.7) = {(n x 128) + A} x fosc / R where,
- fvco : VCO output frequency
- Binary value of the 10-bit programmable counter
- A : Binary value of the 7-bit programmable counter
-
fosc : 12.8MHz reference frequency
- Binary value of the 14-bit programmable counter
2560 (5, 10, 15, 20, or 25kHz step mode) 2048 (12.5kHz step mode)
In 5, 10, 15, 20, or 25kHz step mode,
n = 208 and A = 36.
Therefore, fvco is calculated as follows:
-
fvco = {(208 x 128) + 36} x 12800 / 2560
-
= {26624 + 36} x 5 = 133300= 133,300MHz
- = 133300= 133.300MHz
-
= {26624 + 36} x 5 = 133300= 133,300MHz
Fig. 4 PLL block diagram
CIRCUIT DESCRIPTION
• 8T (8V in transmit mode) and unlock circuits
In receive mode, the base of Q17 has 0.7V. As a result, Q17 is on, and Q16 and Q14 are off, and the collector of Q14 (8T) provides no voltage.
The CPU outputs serial data to the shift register IC5 when the PTT switch is depressed. As a result, pin 8 of IC5 becomes "L", turning Q17 off, and Q16 and Q14 on. The 8T line is therefore supplied with 8V.
The unlock circuit operates only in transmit mode. Q18 is a PLL unlocking switching transistor. Usually, the base of Q18 is supplied with 0V (''L''), and the collector is supplied with 8V (''H'').
When the PLL is unlocked, the base of Q18 is supplied with 0.7V, turning Q18 on. As a result, the collector of Q18 becomes "L" (0V). This turns Q16 off and the collector of Q14 becomes 8V, turning it off. Therefore, when the PLL is unlocked, Q14 is off removing bias voltage from the 8T line. Without the 8T voltage no transmit signal is generated.
Overview
The digital control unit consists of a several keys, a rotary encoder input, a display, a reset circuit, a back-up circuit, and a tone output circuit. These circuits are controlled by a single microcomputer (CPU).
Key and rotary encoder input circuits
The keys on the panel are arranged in matrix. Key input is fed into the CPU, using a key scan technique. Output from the rotary encoder is fed directly into the CPU.
Microphone key input circuit
The UP, DOWN, and other function keys of the microphone are directly connected to their corresponding analog input pins of the CPU. Each of the functions is activated by a voltage generated when the corresponding key is pressed.
Reset and back-up circuits
When the TM-241 A/E power is turned on, the reset circuit sends a "L" level pulse to the RESET pint of the CPU for approx. 3 ms. This initiates the power-on reset sequence.
When the TM-241 A/E power is turned off, the backup circuit detects a voltage drop in the 5 C line and sets CPU INT4 to a "H" level. This causes the CPU to enter a back-up state.
TM-241A/E
Fig. 5 8T and unlock circuits
Fig. 6 Microphone key input circuit
CIRCUIT DESCRIPTION
Display circuit
The display circuit is contained in the LCD assembly. It consists of a LCD driver, its peripheral circuits, and an LCD. The LCD is dynamically operated at a 50% duty cycle. The LCD driver receives LCD data from P33, P140, and P141 of the CPU.
Dimmer circuit
The lamp circuit generates a constant voltage of about 8.8 V with SB, Q205, and D202. The lamp circuit resistance is changed by turning Q203 and Q204 on and off to control the dimmer. If the lamp is shorted, Q206 decreases the Q205 VBE to prevent an overcurrent from flowing through Q205.
Fig.10 Dimmer circuit
Shift register circuit
The shift register circuit consists of IC5 (TC9174F). The IC5 receives serial data from the microcomputer to perform the controls listed below.
| Pin No. Pin name | Function | |
|---|---|---|
| 1 | GND | |
| 2 | B1 | Usually "H". |
| 3 | B2 | Open. |
| 4 CE |
Electronic VOL select :
"H" when electronic VOL selected, "L" when panel VOL selected or interface connected. |
|
| 5 | VOLD | Electronic VOL DOWN ; "L" when DOWN key ON. |
| 6 | VOLU | Electronic VOL UP : "L" when UP key ON. |
| 7 | MUTE | AF MUTE : "H" when TX mode, AL 1ch receive mode, CTCSS, bell, or squelch is ON. |
| 8 | T/R |
Transmit/receive select : "H" in RX mode,
"'L" in TX mode. |
| 9 | TXM |
TX power select : "H" in HI or MID mode,
"L" in LOW mode. |
| 10 | ТХН |
TX power select : "H" in HI mode,
"L" in MID or LOW mode. |
| 11 | - | Open. |
| 12 | - | Open. |
| 13 | DATA | Serial data input. |
| 14 | CLOCK | Clock input. |
| 15 | EN | Enable input. |
| 16 | VDD | |
Table 5
Tone output circuit
R246 (ladder resistor) receives signals from P40 to P43 and P50 to P53 of the CPU and converts them from digital to analog to produce 38 different waveforms from 67.0 Hz to 250.3 Hz. Figure 8 shows the internal configuration of R246.
Fig.8 Internal configuration of ladder resistor (TX-RX unit B/2 R246)
TM-241A/E
CIRCUIT DESCRIPTION
PLL data output
Shift register
swallow counter
main counter Port setting
frequency select
Division ratio A in 20 21 23 27 24 28 24
PLL data is available from P21 (CK), P22 (DT), and P23 (EP1) of the CPU. Figure 9 is a timing chart for PLL data transfer, and Figure 10 shows the format of PLL
Fig. 9 timing chart for PLL data transfer
Input and output of CTCSS unit (option)
The optional CTCSS unit receives data from P21, P22. an P73 of the CPU. Figure 11 is a timing chart for CTCSS data transfer, and Figure 12 shows the format of CTCSS data. When a tone from the CTCSS unit is detected, a "H" level signal is sent to P63 of the CPU, opening the squelch.
· Input and output of the remote control unit (option)
When the optional remote control unit is connected, a "H" level signal is applied to INTO of the CPU, and the following pins have different functions:
-
P03 → S1 : Serial data input pin
- P02 → S2 : Serial data output pin
- P01 → SCK : Serial clock I/O pin
Fig. 11 Timing chart for CTCSS data transfer
Tone frequency select data for CTCSS unit
Example: 88.5Hz L H L H
Fig. 12 CTCSS data format
2. Reference frequency (ref) select (2 bits)
The 21-bit data is made up of the following:
1. Division ratio data A and N (17 bits)
= ((N x 128) + A) x 12.8MHz / ref
| Data | Phase reference | ||
|---|---|---|---|
| D1 | D2 | frequency | and the second se |
| L | L | 5kHz | 5, 10, 15, 20, 25kHz step mode |
| н | L | 6.25kHz | 12.5kHz step mode |
N : Division ratio set in 10-bit main counter (binary)
A : Division ratio set in 7-bit swallow counter (binary)
3. Switch select (2 bits)
| Data Output port | ||||
|---|---|---|---|---|
| SW2 | SW1 | D4 | D3 | |
| RX mode | н | L | н | L |
| TX mode | L. | Н | L | н |
Fig. 10 PLL data format
CIRCUIT DESCRIPTION
| Pin No. | Pin name | 1/0 | Logic | Function | Pin No. | Pin name | 1/0 | Logic | F | unction |
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | P41 | 0 | 33 | PTH01 | -1 | + | Mic DOWN/M | IR/PF input | ||
| 2 | P40 | 0 | 1 - 1 | 34 | PTH00 | Ť | - | Mic UP/CALL/ | VFO input | |
| 3 | P53 | 0 | - | D/A digital putaut (taga) | 35 | TIO | 1 | н | CTCSS DET | |
| 4 | P52 | 0 | - | D/A digital butput (tone), | 36 | TI1 | 1 | L | Not used: (GN | D) |
| 5 | P51 | 0 | - | Dimmor coloct | 37 | P23 | 0 | L | PLL IC enable | output. |
| 6 | P50 | 0 | ÷ | Diminier select | 38 | P22 | 0 | 42 | Serial data out | put. |
| 7 | RESET | 1 | L | Reset input. | 39 | P21 | 0 | 1.0-0 | Serial clock out | tput, |
| 8 | X2 | ÷ | - | 40 | P20 | 0 | - | Beeper output | ||
| 9 | X1 | + | - | 4.134304IVINZ Crystal Oscillator. | 41 | P03/S1 | 1/1 | L/- | Serial data inpu | ut. (KENWOOD BUS) |
| 10 | P63 | 1 | Н | Function display | 42 | P02/SO | 1/0 | L/- | Serial data out | put. (KENWOOD BUS) |
| 11 | P62 | 0 | н | DRS remote control ST | 43 | P01/SCK | 1/- | L/- | Serial clock I/C | . (KENWOOD BUS) |
| 12 | P61 | 0 | - | DRS unit Reset ACL | 44 | INT4 | 1. | н | Back-up detect | input, (Back-up; HI) |
| 13 | P60 | T | H | DTMF Signal detect | 45 | P123 | 1. | L | CALL, VFO | |
| 14 | P73 | 0 | н | CTCSS unit enable output. | 46 | P122 | 1 | L | F. MR/M | |
| 15 | P72 | 0 | н | Shift register enable output. | 47 | P121 | 1 | L | SHIFT, MHz | Destination |
| 16 | P71 | 0 | н | DRS unit VOB output. | 48 | P120 | 1 | L | TONE | key input. |
| 17 | P70 | 0 | н | DRS unit VOA output. | 49 | P133 | 1 | L | REV | |
| 18 | P83 | 0 | н | DRS OF, DTSS EN | 50 | P132 | 1 | L | LOW, DRS/DT | SS |
| 19 | P82 | 0 | Н | DRS unit STBY output. | 51 | P131 | 1 | L | Not used (GND | 0) |
| 20 | P81 | 0 | L | DTSS DTSEL output . DRS unit WR output | 52 | P130 | 1 | L | Busy input | |
| 21 | P80 | 0 | L | DRS unit RD output. | 53 | P143 | 0 | L | Squelch contro | ol. |
| 22 | P93 | 0 | н | DRS unit data output. D8/D3 | 54 | P142 | 0 | н | Power SW. | |
| 23 | P92 | 0 | Н | DRS unit data output. D4/D2 | 55 | P141 | 0 | - | LCD driver clo | ck output. |
| 24 | P91 | 0 | н | DRS unit data output. D2/D1 | 56 | P140 | 0 | - | LCD driver dat | a output. |
| 25 | P90 | 0 | Н | DRS unit data output. D1/D0 | 57 | NC | - | - | Not used. (Von | ) |
| 26 | Vss | ÷ | - | GND. | 58 | VDD | - | - | Power supply | pin. |
| 27 | P13 | 1 | Н | DRS unit connect check. | 59 | P33 | 0 | - | LCD driver ena | able output. |
| 28 | INT2 | 1 | - | Encodering | 60 | P32 | 0 | L | Distination out | put. |
| 29 | INT1 | 1 | Encoder Input. | 61 | P31 | 0 | L | P.C.P. | ||
| 30 | P10 | 1 | Н | Remote connect detect input. | 62 | P30 | 0 | L | Key output. | |
| 31 | PTH03 | Ĵ. | S-meter analog input. | 63 | P43 | 0 | - | |||
| 32 | PTH02 | 1 | - | Not used. (GND) | 64 | P42 | 0 | 1 | D/A digital out | put (tone). |
Table 6 75116GF-728-3BE terminal functions (TX-RX unit IC201)
DESCRIPTION OF COMPONENTS
| Component | Use/Function | Operation/Condition/Compatibility |
|---|---|---|
| IC1 |
2nd local oscillator,
IF amplification, detection, low-frequency amplification, noise amplification, noise detection, squelch switching |
|
| IC2 | AM detector | |
| IC3 | AF amplification | ① AF input, ⑧ AF output. |
| IC4 |
Electronic volume control,
AF switch |
② AF output. ⑦ Panel volume input. ③ ''L'' during step-up. ⑧ Panel volume output. ④ ''L'' during step-down. ⑩ AF input. ⑤ ''H'' when electronic volume selected. |
| IC5 | Shift register | See circuit description. |
| IC6 | 5V AVR | |
| IC7 | 10V AVR | For PLL. |
| 1C8 | Transmit drive | |
| IC9 | 8V AVR | |
| IC201 | Microprocessor | See circuit description. |
| IC202 | 6V AVR | |
| Q1 | High-frequency amplification | Operates in receive mode. |
| Q2 | 11R switching | On when the aircraft band is selected. |
| Q3 | BPF switching | On when the aircraft band is selected. |
| Q4 | 1st mixer | Converts received 144 MHz-range signals to 1st IF 10.7 MHz. |
| Q5 | High-frequency amplification | Amplifies 1st IF signal. |
| Q6 | Q5 Gain control | |
| Q7 | Detector output switch | When the aircraft band is selected, the FM detection switch is turned off. |
| Q8 | AF amplifier | When the aircraft band is selected, the output signal from the AM detector is amplified. |
| Q9 (1/2) | RD line mute | ON when DRS unit replays. |
| Q9 (2/2) | AF line mute | |
| Q10 | Low-frequency amplification | Operates when DRS unt replays. |
| Q11 | 2nd local oscillator buffer | |
| Q12 | AF line mute | Operates when transmit mode, AL 1ch receive mode, CTCSS, bell or squelch is ON. |
| Q13 | 8R switching | ON in receive mode. |
| Q14 | 8T switching | ON in transmit mode. |
| Q15 | 8R switching control | ON in receive mode. |
| Q16 | 8T switching control | ON in transmit mode. |
| Q17 | 8T switching control | OFF in transmit mode. |
| Q18 | 8T switching control | OFF when PLL locked. |
DESCRIPTION OF COMPONENTS
| Component | Use/Function | Operation/Condition/Compatibility |
|---|---|---|
| Q19 | Mic line mute | ON in receive mode. |
| Q20 | PLL 8V ripple filter | |
| 221 | CV line buffer | |
| 022 | VCO output amplification | |
| Q23 | TX power select | ON in HI or MID mode. |
| Q24 | TX power select | |
| Q25 | TX drive stage +B control | |
| 026 | Power switch | |
| 227 | Power switch control | ON when power switch is ON. |
| 028 | Squelch hysteresis | On when the squelch is on |
| 2201, 202 | Function dimmer switch | Refer to circuit description. |
| 2203, 204 | Lamp dimmer switch | |
| 0207 | Reset switch |
ON for approx. 3ms
when system power turned on, usually OFF. |
| 2208 | Back-up switch | OFF when 13.8 V line becomes DIM |
| 2209, 210 | Dimmer switch ON/OFF | Turn Q201~Q204 on or OFF dimmer 1 2 3 4 Q209 ON OFF ON OFF Q210 ON ON OFF OFF |
| 0211 | Function drive switch | |
| 2212 | Mic mute | On when DTSS and paging codes are sent. |
| 01 | Band select switch. (AM/FM) | On when the aircraft band is selected. |
| 02~6 | Vari-cap tuning | |
| 07~9 | Reverse current prevention | |
| 010 | VCO output switch | |
| 011 | Temperature compensation | For APC. |
| 012,13 | Transmit/receive switching. |
TM-241A/E
DESCRIPTION OF COMPONENTS
| Component | Use/Function | Operation/Condition/Compatibility |
|---|---|---|
| D14,15 | Power detection | For APC |
| D16 | Reverse power protection | |
| D202 | Lamp standard voltage | |
| D203 | Dimmer switch | |
| D204, 205 | D205 switches in the lithium battery when the power is off | |
| D206~211 | Used for destination setting. | |
| D212 | CPU protector. | |
| D213 | Reverse current prevention | |
| D214 | Back-up detection voltage | |
| D215 | Reset detection voltage | |
| D216 | Function LED |
PLL (X58-3470-00)
| Component | Use/Function | Operation/Condition/Compatibility | |||||
|---|---|---|---|---|---|---|---|
| IC51 | PLL |
|
|||||
| Q51 | VCO output buffer | ||||||
| Q52 | Transmit switch | OFF in transmit mode. | |||||
| Q53 | Transmit switch | ON for moment when transmission starts | |||||
| Q101,102 | LPF | ||||||
| Q1 | VCO output buffer | ||||||
| Q2 | VCO |
133.300~135.295MHz (
E,M
), 125.300~163.295MHz (
K,P,E
2
,M
2
) in receive mode.
144.000~145.995MHz ( E ), 144.000~147.995MHz ( K,P,M ) 136.000~173.995 MHz ( E 2 ,M 2 )in transmit mode. |
|||||
| D1 | For modulation in TX mode | ||||||
| D2 | VCO voltage control | ||||||
APC (X59-3130-00)
| Component | Use/Function | Operation/Condition/Compatibility |
|---|---|---|
| Q1 | Differential amplification | epsite on a company of the part of the |
| 02 (2/2) | APC control | |
| Q3 | Drive stage +B AVR |
MIC AMP (X59-3610-00)
| Component | Use/Function | Operation/Condition/Compatibility |
|---|---|---|
| IC1 (1/2) | Limited amplification | spectrum, company company |
| IC1 (2/2) | LPF | |
| Q1 | Low-frequency amplification |
* New Parts
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht geliefert.
|
Ref. No.
参照者号 |
Address
位 音 |
Parts | Parts No. | Description |
Desti-
nation |
Re- |
|---|---|---|---|---|---|---|
| 31 | 100 HH 10 73 |
副唱台/观悟
TM-241 |
甘同 | 加度視 | ||
| 1 | 1 | 1101-241 | 1 | 1 | ||
|
1
2 3 4 5 |
18
28 1C 28 2A |
* |
A01-1065-03
A01-1066-03 A10-1292-01 A22-0770-03 A62-0007-23 |
METALLIC CABINET(TOP)
METALLIC CABINET(BOTTOM) CHASSIS CALKED ASSY SUB PANEL PANEL ASSY |
KMM2P | |
| 24 | * | A62-0008-23 | PANEL ASSY | EE2 | ||
|
5
7 3 9 |
28
28 28 18,10 |
¥ |
B11-0484-08
B30-0869-05 B38-0330-05 B42-2455-04 B42-3343-04 |
FILTER(LCD)
LAMP LCD ASSY LABEL(MAX8 MAX) S/NO LABEL(NAME PLATE) |
||
|
1A
1B 1B |
* * |
842-3356-04
842-3394-04 862-0031-00 862-0032-00 862-0032-00 |
LABEL(EXT SP)
FCC LABEL INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL |
K
K MM2P EE2 |
||
|
2
0 |
* |
B62-0033-00
B72-0093-04 B72-0094-04 B72-0095-04 B46-0410-20 |
INSTRUCTION MANUAL
MODEL NAME PLATE MODEL NAME PLATE MODEL NAME PLATE WARRANTY CARD |
EE2
KP MM2 EE2 K |
||
| 0 |
846-0419-00
846-0422-00 |
WARRANTY CARD
WARRANTY CARD |
E p | |||
|
3
4 5 |
1C
1C |
E30-2111-05
E30-2137-15 E30-2145-05 E31-3197-15 |
DC CABLE
DC CABLE ANT CABLE CONNECTING WIRE(SP) |
|||
|
6
7 9 |
1C
1B 1B |
¥ |
F05-1531-05
F05-2036-05 F15-0670-04 F20-0587-04 F20-1059-04 |
FUSE 15A
FUSE 20A SHADE INSULATING BØARD(LITHIUM BATT) INSULATING BØARD(LITHIUM BATT) |
||
|
1
2 3 4 |
18,1C
2A 18,2C |
G02-0565-04
G02-0576-14 G09-0405-05 G10-0651-04 G10-0681-04 |
FLAT SPRING
FLAT SPRING SPRING (KNOB) NON-WOVEN FABRIC(SP) NON-WOVEN FABRIC(CHASSIS) |
КР | ||
| 5 |
18,28
28 |
G10-0686-04
G13-0906-04 |
NON-WOVEN FABRIC(CASE)
CUSHION (3KEY) |
|||
|
7
8 |
2A
2B |
G13-0926-04
G13-0960-04 G13-0961-04 |
CUSHION (CONT)
CUSHION (6KEY) CUSHION (LOW) |
|||
| 9 | H10-2658-02 | POLYSTYRENE FOAMED FIXTURE | ||||
|
0 A
0 B 0 B 1 2 |
H11-0822-04
H11-0823-04 H11-0823-04 H13-0814-04 H13-0825-04 |
POLYSTYRENE PLATE
POLYSTYRENE PLATE POLYSTYRENE PLATE PROTECTION SHEET PROTECTION SHEET |
K
MM2P EE2 MM2P |
|||
| 2 6 6 | * } |
H13-0825-04
H52-0054-04 H52-0055-04 |
PROTECTION SHEET
ITEM CARTON BOX ITEM CARTON BOX |
EE2
KMM2P EE2 |
E: Scandinavia & Europe K: USA P: Canada W:Europe U: PX(Far East, Hawaii) T: England M: Other Areas
UE : AAFES(Europe) X: Australia
TM-241A: K, P, M, M2 TM-241E: E, E2
TM-241A/E
PARTS LIST
* New Parts Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht gellefert.
TX-RX UNIT (X57-369X-XX)
|
Ref. No.
参照香号 |
Address
位 置 |
New
Parts 新 |
Parts No.
部品番号 |
Description
部品名/規格 |
Desti-
nation 仕 向 |
Re-
marks 備考 |
|---|---|---|---|---|---|---|
|
-
33 34 35 |
H10-2658-02
H25-0029-04 H25-0117-04 H25-0720-04 |
POLYSTYRENE FOAMED FIXTURE
PROTECTION BAG(MIC HOOK) PROTECTION BAG(DC CABLE) PROTECTION BAG(RADIO) |
KP | |||
|
37
38 40 41 |
1C
2A |
J19-1434-04
J20-0319-24 J21-4303-08 J29-0436-03 |
HØLDER(SP)
MIC HØØK MØUNTING HARDWARE(LCD ASSY) BRACKET |
Κ₽ | ||
|
42
43 44 45 46 |
28
28 28 28 2A 2A |
K27-3035-14
K27-3066-04 K27-3067-04 K27-3068-04 K27-3068-04 K27-3069-04 |
KNOB(ENCODER)
KNOB(POWER SW) KNOB(LOW) KNOB(CALL) KNOB(FUNC) |
|||
|
47
48 49 50 51 |
2A
2A 2A 2A 2A 2A |
* |
K27-3071-04
K27-3072-04 K27-3074-04 K27-3075-04 K29-3156-04 |
KNØB(TONE)
KNØB(REVERSE) KNØB(SHIFT) KNØB(DR/DT) KNØB(MAIN) |
||
| 52 | 2A | K29-3157-04 | KNOB(VOL) | |||
|
A
B C G |
28
28 1C,2C |
N09-0626-04
N09-0650-05 N33-2606-45 N46-3010-46 N87-2606-46 |
SCREW(POWER MODULE 3X10)
SCREW(SUB PANEL) OVAL HEAD MACHINE SCREW(CASE) PAN HEAD TAPPING SCREW BRAZIER HEAD TAPTITE SCREW |
КP | ||
|
E
F 53 |
28
28 |
N87-2610-46
N88-2606-46 N99-0331-05 |
BRAZIER HEAD TAPTITE SCREW
FLAT HEAD TAPTITE SCREW SCREW SET |
|||
|
SP
54 54 54 |
10 |
T07-0246-05
T91-0379-25 T91-0380-35 T91-0382-25 |
LOUDSPEAKER
MICROPHONE MICROPHONE(DTMF) MICROPHONE(1750Hz TONE) |
MM2
KP EE2 |
||
|
IC1
IC301 |
- |
LC7582
S-AV17 |
1C(LCD DRIVER)
IC(POWER MODULE FOR 144MHZ) |
|||
|
55
56 |
28 |
W01-0414-04
W09-0326-05 |
WRNCH
LITHIUM BATTERY |
|||
|
57
57 57 57 57 |
28,2C
28,2C 28,2C 28,2C 28,2C 28,2C |
* |
X57-3690-11
X57-3690-21 X57-3690-22 X57-3692-71 X57-3692-72 |
TX RX UNIT
TX RX UNIT TX RX UNIT TX RX UNIT TX RX UNIT |
KP
M 8 5 2 |
|
| TX-R | X UNIT | (X5 |
7-369X-XX) 0-1
2-7 |
1: TM-241A (K, P), 0-21: TM-241A (M), 0-22: TM-24
1: TM-241E (E), 2-72: TM-241E (E2) |
1A (M2) | |
|
C1
C2 C3 C3 C3 |
CC73FCH1H040C
CC73FCH1H060D CC73FCH1H040C CC73FCH1H070D CC73FCH1H070D |
CHIP C 4PF C
CHIP C 6PF D CHIP C 4PF C CHIP C 7PF D CHIP C 7PF D CHIP C 7PF D |
KP
KP MM2 BE2 |
|||
|
C4 15
C6 7 C8 C9 C10 |
CK73FB1H102K
CK73FB1H102K CK73FB1H103K CK73FB1H103K CK73FB1H102K CC73FCH1H0R5C |
CH1P C 1000PF K CH1P C 1000PF K CH1P C 0.010UF K CH1P C 1000PF K CH1P C 0.5PF C | KP | |||
| C11 | CC73FCH1H470J | CHIP C 47PF J |
indinavia & Europe K: USA P: Canada W
U: PX(Far East, Hawaii) T: England M: Other Areas
UE : AAFES(Europe) X: Australia
TM-241A: K, P, M, M
M-241E: E, E2
* New Parts
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht geliefert.
TX-RX UNIT (X57-369X-XX) Ref. No. Address New Parts No. Description Desti- Renation marks 主 向 備考 参照番号 位 筐 新 部品番号 部品名/規格 CK73FB1H103K 0.010UF 1000PF CHIP C CC73FCH1H470J 1000PF CK73FB1H102K 1000PF 1000PF 0.010UF 22PF CK73FB1H102K CHIP C 150PF CK73FB1H102K CK73EF1C105Z 1.0UF 0.022UF CHIP TAN CHIP C C38 CHIP TAN CHIP C C92-0002-05 CK73EF1C1052 35WV ELECTRO 10WV CK73EB1H104K CE04EW1A471M ELECTRO 10WV CH1P C ELECTRO 0.010UF 47UF 16WV -53 IOWV CC73FSL1H101J CHIP C ELECTRO ,58 CK73EF1C105Z IOWV C61 092-0504-05 CHIP TAN 0.68UF 20WV CE04EW1A470M CHIP TAN CHIP C 20WV K C65 ,66 CHIP-TAN 1.5UF 0.010UF 1000PF 6.3WV CK73EB1H473K CK73FB1H102K ,76 1000PF E: Scandinavia & Europe K: USA
P: Canada W:Europe U: PX(Far East, Hawaii) T: England M: Other Areas
UE : AAFES(Europe) X: Australia
TM-241A: K, P, M, M2
4
4
ال
ų.
Q
PARTS LIST
Parts without Parts No. are not supplied.
* New Parts
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Telle ohne Parts No, werden nicht gellefert
| Ref. No. | Address New | Parts No. | Description | Desti- | Re- | |
|---|---|---|---|---|---|---|
| 参照番号 | 位置新 | 部品香号 | 部品名/規 | 格 | t 向 |
marks
儒考 |
|
C80
C81 C82 C83 C84 |
CK73FB1H102K
CC73FCH1H220J CK73FB1H103K CE04EW1A470M CK73FB1H103K |
CHIP C 1000PF
CHIP C 22PF CHIP C 0.010UF ELECTRO 47UF CHIP C 0.010UF |
K
J K 10WV K |
|||
|
C85
C86 C87 ,88 C89 -92 C93 |
CE04EW1A221M
CE04EW1C100M CK73FB1H103K CK73FB1H102K CK73FB1H102K CK73FB1H103K |
ELECTRØ 220UF
ELECTRØ 10UF CHIP C 0.010UF CHIP C 1000PF CHIP C 0.010UF |
10WV
16WV K K K |
|||
|
C94
C95 ,96 C97 C99 C100 |
CE04EW1A470M
CK73FB1H103K CE04EW1C102M CK73FB1H102K CK73FB1H102K CK73EF1C105Z |
ELECTRO 47UF
CHIP C 0.010UF ELECTRO 1000UF CHIP C 1000PF CHIP C 1.0UF |
10WV
K 16WV K Z |
|||
|
C101
C102 C104 C105 C106 |
CK73FB1H102K
CE04EW1C100M CC73FCH1H150J CK73FB1H102K CC73FCH1H220J |
CHIP C 1000PF
ELECTRØ 10UF CHIP C 15PF CHIP C 1000PF CHIP C 22PF |
K
16WV J K J |
|||
|
C107
C108 C109 C110 C111-113 |
CK45B2H102K
CM73F2H330J CC73FCH1H0R5C CC73FCH1H020C CK73FB1H102K |
CERAMIC 1000PF
CHIP C 33PF CHIP C 0.5PF CHIP C 2.0PF CHIP C 1000PF |
K
J C C K |
|||
|
C114
C115 C116 C117 C118 |
CC45SL2H560J
CC45SL2H470J CC73FCH1H0R5C CC73FCH1H020C CM73F2H270J |
CERAMIC 56PF
CERAMIC 47PF CHIP C 0.5PF CHIP C 2.0PF CHIP C 27PF |
C
C C C C C C C C C C C C C C C C C C |
|||
|
C119
C120 C121 C122 C122 C123 |
CK73FB1H102K
C92-0511-05 CK73EF1C1052 CK73FB1H102K CK73EF1C1052 |
CHIP C 1000PF
CHIP TAN 0.15UF CHIP C 1.0UF CHIP C 1000PF CHIP C 1.0UF |
K
35WV Z K Z |
|||
|
C125
C126 C127 C201 C202 |
CM73F2H060D
CC73FSL1H101J CK73FB1H332K CK73FB1H102K CK73FB1H102K CK73FB1H103K |
CHIP C 6.0PF
CHIP C 100PF CHIP C 3300PF CHIP C 1000PF CHIP C 1000PF CHIP C 0.010UF |
D
J K K K |
|||
|
C203
C204 C205 C206 C207 |
CK73FB1H102K
CK73FB1H103K CE04NW0J221M CK73FB1E223K CK73FB1H102K |
CHIP C 1000PF CHIP C 0.010UF ELECTRØ 220UF CHIP C 0.022UF CHIP C 1000PF |
K
K 6.3WV K K |
|||
|
C208,209
C210,211 C212-214 C215-217 C219,220 |
CC73FCH1H330J
CK73FB1H103K CC73FSL1H101J CK73FB1H102K CK73FB1H102K CK73FB1H103K |
CHIP C 33PF
CHIP C 0.010UF CHIP C 100PF CHIP C 100PF CHIP C 1000PF CHIP C 0.010UF |
J
K J K K |
|||
| TC1 | 005-0349-05 | TRIMMING 10PF | ||||
|
CN1
CN2 CN3 ,4 |
E40-3237-05
E40-5182-05 E40-5202-05 |
PIN CONNECTOR(INT.SP)
PIN CONNECTOR(DRU) PIN CONNECTOR(TR) |
E: Scandinavia & Europe K: USA P: Canada W:Europe
TM-241A: K, P, M, M2 TM-241E: E, E2
UE : AAFES(Europe) X: Australia
U: PX(Far East, Hawaii) T: England M: Other Areas
* New Parts
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis,
Telle ohne Parts No. werden nicht geliefert.
TX-RX UNIT (X57-369X-XX) Ref. No. Address New Parts No. Desti- Re-Description 参照番号 位 T 部品番号 部品名/規格 向備考 新 E40-5183-05 PIN CONNECTOR(DTM) CN201,202 PIN CONNECTOR(CONT) PIN CONNECTOR(DRU) PIN CONNECTOR(DRU) PIN CONNECTOR EXT SP JACK MIC RECEPTACLE E11-0425-05 E06-0860-05 TEST TERMINAL FINISHED WIRE SET(HET) CONNECTING WIRE(CTCSS) E33-1871-15 FINISHED WIRE SET COLLAR CERAMIC DISCRI(CDBM455C16) CERAMIC FILTER(CFWM455F) -4 L34-4080-05 COIL 17 L40-1001-48 SMALL FIXED INDUCTOR(100H) L34-1239-05 L34-0895-05 COIL COIL L34-0499-05 COIL SMALL FIXED INDUCTOR(3.30H) COIL CRYSTAL RESONATOR(10.245MHz) L77-0946-15 L77-1405-05 CRYSTAL RESONATOR(12.8MHz) X201 L77-1397-05 CRYSTAL RESONATOR(4.194304MHz) CRYSTAL FILTER(10.7MHz) L71-0228-05 6.8K 1/10W KP 1/10W 1/10W RK73FB2A101J 100 1/10W 1/10W 10K 1.0K 1/10W 1/10W O OHM 1/10W 1/10₩ 1/10₩ RK73FB2A101J 100 1/10W 10K 1/10W
E: Scandinavia & Europe K: USA P: Canada W:Europe
TM-241A: K, P, M, M2 TM-241E: E, E2
الليد
الخب
الغي
di)
÷
4
-
U: PX(Far East, Hawaii) T: England M: Other Areas UE : AAFES(Europe) X: Australia
PARTS LIST
Parts without Parts No. are not supplied.
* New Parts
Ref. No.
参照番号
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
部
RK73E
Telle ohne Parts No. werden nicht gellefe Address New
位置 新
| rt. | T (X57-369X-XX | |||||
|---|---|---|---|---|---|---|
|
rts No.
品 書 号 |
Description
部 品 名/規 |
格 |
Desti-
nation 仕 向 |
Re-
marks 備考 |
||
| 2A103J | CHIP R | 10K | J | 1/10W | 1000 | |
| 2A681J | CHIP R | 680 | J | 1/10W | KP | |
| 2A153J | CHIP R | 15K | J | 1/10W | 100 | |
| 2A274J | CHIP R | 270K | J | 1/10W | KP | |
| 2A332J | CHIP R | 3.3K | J | 1/10W | KP | |
| 2A102J | CHIP R | 1.0% | J | 1/10W | KP | |
| 2A102J | CHIP R | 1.OK | J | 1/10W | ||
| 2A334J | CHIP R | 330K | J | 1/10W | ||
| 2A331J | CHIP R | 330 | 3 | 1/10W | ||
| 743311 | CHIP P | 330 | T | 1/100 | ||
| Sur II | 2.20 | 11 104 | 04 | |||
|---|---|---|---|---|---|---|
|
R33
R35 ,36 R37 R38 R40 |
RK73FB2A102J
RK73FB2A102J RK73FB2A334J RK73FB2A331J RK73FB2A331J RK73FB2A331J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
1.0K
1.0K 330K 330 330 |
1111 |
1/10W
1/10W 1/10W 1/10W 1/10W |
ΚP |
|
R43
R44 R45 R46 R47 |
R92-1220-05
RK73FB2A101J R92-0670-05 RK73FB2A102J RK73FB2A473J |
CHIP R
CHIP R CHIP R CHIP R CHIP R |
1
100 0 0HM 1.0K 47K |
1
1 1 |
1/10W
1/10W 1/10W |
|
|
R48
R49 R50 R51 R52 |
RK73FB2A333J
RK73FB2A473J RK73FB2A473J RK73FB2A223J RK73FB2A472J RK73FB2A102J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
33K
47K 22K 4.7K 1.0K |
1
1 1 1 |
1/10W
1/10W 1/10W 1/10W 1/10W |
|
|
R53
R54 R55 R56 -58 R59 |
RK73FB2A334J
RK73FB2A223J RK73FB2A182J RK73FB2A182J RK73FB2A103J RK73FB2A182J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
330K
22K 1.8K 10K 1.8K |
1
1 1 1 1 1 |
1/10W
1/10W 1/10W 1/10W 1/10W |
|
|
R6D
R61 R62 R63 R63 |
RK73FB2A223J
RK73FB2A473J R92-0670-05 RK73FB2A102J RK73FB2A332J |
CH1P R
CH1P R CH1P R CH1P R CH1P R CH1P R |
22K
47K 0 0HM 1.0K 3.3K |
1
1 1 |
1/10W
1/10W 1/10W 1/10W |
EE2
KPMM2 |
|
R64
R64 R65 ,66 R67 R68 |
RK73FB2A392J
RK73FB2A563J R92-0670-05 RK73FB2A220J R92-0670-05 |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
3.9K
56K 0 0HM 22 0 0HM |
J
J |
1/10W
1/10W 1/10W |
KPMM2
EE2 |
|
R69
R70 ,71 R72 R73 R74 |
RK73FB2A184J
RK73FB2A103J R92-0670-05 RK73FB2A223J R92-0670-05 |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
180K
10K 0 0HM 22K 0 0HM |
J
J |
1/10W
1/10W 1/10W |
|
|
875 -78
879 880 881 882 |
RK73FB2A472J
RK73FB2A105J RK73FB2A104J RK73FB2A404J RK73FB2A471J RK73FB2A220J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
4.7K
1.0M 100K 470 22 |
1000 |
1/10W
1/10W 1/10W 1/10W 1/10W |
|
|
R84
R85 R86 R87 R88 ,89 |
RK73FB2A122J
RK73FB2A220J RK73FB2A223J RK73FB2A103J RK73FB2A101J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
1.2K
22 22K 10K 100 |
1111 |
1/10W
1/10W 1/10W 1/10W 1/10W |
|
|
R90
R91 R92 R94 R95 |
RK73FB2A102J
RK73FB2A470J RK73FB2A104J RK73FB2A220J RK73FB2A472J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
1.0K
47 100K 22 4.7K |
L
L L L L L |
1/10W
1/10W 1/10W 1/10W 1/10W |
E: Scandinavia & Europe K: USA
P: Canada W:Europe
TM-241A: K, P, M, M2 TM-241E: E, E2
U: PX(Far East, Hawaii) T: England M: Other Areas UE : AAFES(Europe) X: Australia
* New Parts
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht gellefert.
TX-RX UNIT (X57-369X-XX) Description Desti- Re-Ref. No. Address New Parts No. nation marks 向備考 参照番号 1 新 部品套号 部品名/規格 1/10₩ RK73FB2A103J 0 OHM CARBON 1/2W 22K 270K 1/10W RK73FB2A103J 1/10W 1/8W FIXED RESISTOR(18 OHM) FIXED RESISTOR(4.7 QHM) CHIP R 4.7K J 1/100 10K 1/10W 4.7K 1/10W O DHM 1/10W R231,232 R233 WOI'S 1/100 R236,237 RK73FB2A102J O OHM RK73FB2A105J MULT1-COMP 18 100K J 1/8W TRIM POT. TRIM POT. vR201 TRIMMING POT. (10K)
E: Scandinavia & Europe K: USA
U: PX(Far East, Hawaii) T: England M: Other Areas
P: Canada W:Europe
TM-241A: K, P, M, M2
اللي
A.
-11
- 44
U.
UE : AAFES(Europe) X: Australia
TM-241A/E
PARTS LIST
Parts without Parts No. are not supplied.
* New Parts
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Telle ohne Parts No. werden nicht gellefert
ene onne Parts No. werden nicht geliefert.
| Ref. No. Add | Parts | Parts No. | Description |
Desti-
nation mark |
|---|---|---|---|---|
| 血 新 | 節痛膏考 | 郡 岳 名 / 規 格 | 仕向備考 | |
|
5201
5202-211 |
S40-2458-05
S40-1086-05 |
POTENTIOMETER(SOKB)
PUSH SWITCH(POWER) TACT SWITCH |
||
|
D1
D2 -6 D7 D8 ,9 D10 |
DAN235K
15V164 LFB01 1SS184 DAN235K |
D10DE
D10DE D10DE D10DE D10DE D10DE |
ΚP | |
|
D11
D12 D13 D14 ,15 D16 |
1SS181
MI407 MI308 1SS226 DSA3A1 |
D10DE
D10DE D10DE D10DE D10DE D10DE |
||
|
D202
D203 D204 D205 D206 |
02CZ9.1(Y)
1SS184 1SS181 1SS184 1SS184 1SS184 |
CHIP ZENER DI@DE
DI@DE DI@DE DI@DE DI@DE |
KPMEM2 | |
|
0207
0209 0210 0211 0212 |
1SS184
MA141A MA141A MA141A 1SS226 |
DIODE
CHIP DIODE CHIP DIODE CHIP DIODE DIODE |
MM2882
MM2882 882 |
|
|
0213
0214 0215 0216 0217 |
LFB01
02CZ3.9(Z) 02CZ3.0(Z) B30-0852-05 1SS184 |
DIODE
CHIP ZENER DIODE CHIP ZENER DIODE LED(LOW) DIODE |
||
|
IC1
IC2 IC3 IC4 IC5 |
KCD04
TA7787AF UPC1241H KCC02 TC9174F |
HIC(FM IF)
IC(FM/AM IF/3V) IC(AF PA) HIC(EL,VQL) IC(CMQS I/Q) |
KP | |
|
106
107 108 109 10201 |
* |
NJM78LO5UA
LA5010M KCB05 MC7808CT 75116GF-728-3BE |
IC(VOLTAGE REGULATOR/ +5V)
IC(LOW SATURATION REGULATOR) HIC(DRIVE) IC(VOLTAGE REGULATORS/ +8V) IC(CPU) |
|
|
C202
21 22 23 24 |
NJM78L06UA
3SK184(S) DTA114YK DTC123JK 3SK131(V12) |
IC(VOLTAGE REGULATOR/ +6V)
FET DIGITAL TRANSISTOR DIGITAL TRANSISTOR FET |
КР
К |
|
|
25
26 27 28 29 |
2SC2714(Y)
2SK208(Y) DTC143EK 2SC2712(Y) FMG2 |
TRANSISTOR
FET DIGITAL TRANSISTOR TRANSISTOR TRANSISTOR |
KP
KP KP |
|
|
210
212 213 ,14 215 216 -18 |
2SC2712(Y)
2SD1757K 2SB1119S DTC144WK 2SC2712(Y) |
TRANSISTOR
TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR TRANSISTOR |
E: Scandinavia & Europe K: USA
P: Canada W:Europe
U: PX(Far East, Hawaii) T: England M: Other Areas UE : AAFES(Europe) X: Australia
TM-241A: K, P, M, M2 TM-241E: E, E2
× New Parts
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Telle ohne Parts No. werden nicht geliefert.
TX-RX UNIT (X57-369X-XX) PLL UNIT (X58-3470-00)
|
Ref. No.
參照番号 |
Addres
位 I |
s New
Parts 新 |
Parts No.
部品番号 |
部 |
Description
品 名 / 規 |
格 |
Desti-
nation 仕 向 |
Re-
marks 備考 |
|---|---|---|---|---|---|---|---|---|
|
Q19
Q20 Q21 Q22 Q22 Q23,24 |
2SD1757K
2SC2712(Y) 2SK208(Y) 2SC2714(Y) DTC124EK |
TRANSISTOR
TRANSISTOR FET TRANSISTOR DIGITAL TRA |
NSISTOR | |||||
|
Q25
Q26 Q27 Q28 Q201-204 |
2SD1406(Y)
2SB1302S 2SC2712(Y) 2SJ106(GR) 2SA1519 |
TRANSISTOR
TRANSISTOR TRANSISTOR FET TRANSISTOR |
||||||
|
Q205
Q206-208 Q209,210 Q211 Q212 |
2SD1682(R,S)
2SC2712(Y) DTC114EK DTD143EK FMG2 |
TRANSISTOR
TRANSISTOR DIGITAL TRA DIGITAL TRA TRANSISTOR |
NSISTOR
NSISTOR |
|||||
| S212 | W02-0388-05 | ROTARY ENCO | DER | |||||
|
X58-3470-00
X59-3130-00 X59-3610-00 |
SUB UNIT(PL
MODULE UNIT MODULE UNIT |
L)
(APC) (MIC AMP) |
||||||
| PLL UNIT (X | 58-3470-00) | |||||||
|
C1
C2 C3 C4 ,5 C6 |
CC73FCH1H220J
CK73FB1H102K CC73FCH1H020C CK73FB1H472K CC73FCH1H010C |
CHIP C
CHIP C CHIP C CHIP C CHIP C |
22PF
1000PF 2.0PF 4700PF 1PF |
с кс
г |
||||
|
C7 -9
C10 C11 C51 C52 |
CK73FB1H102K
CK73FB1H472K CK73FB1H102K CC73FCH1H100D CK73FB1H102K |
CHIP C
CHIP C CHIP C CHIP C CHIP C CHIP C |
1000PF
4700PF 1000PF 10PF 1000PF |
K
K D K |
||||
|
C53
C54 C55 C56 C101 |
CC73FCH1H100D
CK73FB1H102K CK73EB1H223K CK73FB1E393K CK73FB1E393K CK73EB1H223K |
CHIP C
CHIP C CHIP C CHIP C CHIP C CHIP C |
10PF
1000PF 0.022UF 0.039UF 0.022UF |
D
K K K |
||||
|
C102
C102,103 C104 C105 C106 |
CK73EB1H223K
C92-0009-05 CK73FB1H102K C92-0003-05 CK73EB1H223K |
CHIP C
CHIP TAN CHIP C CHIP TAN CHIP C |
0.022UF
4.7UF 1000PF 0.47UF 0.022UF |
K
10WV K 25WV K |
||||
|
C107
C108 C109,110 |
CC73FCH1H100D
CC73FCH1H220J CK73FB1H102K |
CHIP C
CHIP C CHIP C |
10PF
22PF 1000PF |
N
D D |
||||
|
CN1
CN2 CN3 |
E40-0311-05
E40-0411-05 E40-5201-05 |
PIN CONNECT
PIN CONNECT PIN CONNECT |
0R(3P)
0R(4P) 0R(7P) |
- | ||||
| F11-1122-14 | SHIELDING C | OVER | ||||||
|
L1
L2 -4 L5 L51 |
L40-1581-80
L40-3391-19 L34-2336-05 L40-3392-81 |
SMALL FIXED
SMALL FIXED COIL SMALL FIXED |
INDUCTOR
INDUCTOR INDUCTOR |
(150NH)
(3.3UH) (3.3UH) |
||||
| RK73FB2A392J | CHIP R | 3.9K | J 1/10W |
PARTS LIST
E: Scandinavia & Europe K: USA P: Canada W:Europe
TM-
TM-241A: K, P, M, M2 TM-241E: E, E2
U: PX(Far East, Hawaii) T: England M: Other Areas UE: AAFES(Europe) X: Australia
TM-241A/E
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Telle ohne Parts No. werden nicht gellefert.
PLL UNIT (X58-3470-00) APC UNIT (X59-3130-00) MIC AMP UNIT (X59-3610-00)
| Ref. No. | Address | New | Parts No. | Description | Desti- | Re- | |||
|---|---|---|---|---|---|---|---|---|---|
| 参照番号 | 位置 | 新 | 部品香号 | 部 | 品名/規 | 格 |
nation
仕 向 |
marks
備考 |
|
|
R1
R2 R3 R4 R5 |
RK73FB2A472J
RK73FB2A561J RK73FB2A101J RK73FB2A121J RK73FB2A470J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
4.7K
560 100 120 47 |
ננננ |
1/10W
1/10W 1/10W 1/10W 1/10W |
||||
|
R6 ,7
R8 R9 R10 R51 |
R92-0670-05
RK73FB2A101J RK73FB2A470J RK73FB2A103J RK73FB2A103J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
0 0HM
100 47 10K 10K |
L |
1/10W
1/10W 1/10W 1/10W |
||||
|
R52
R53 R54 R55 R101 |
RK73FB2A223J
RK73FB2A221J RK73FB2A472J RK73FB2A473J RK73FB2A473J RK73FB2A152J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
22K
220 4.7K 47K 1.5K |
1111 |
1/10W
1/10W 1/10W 1/10W 1/10W |
||||
|
R102
R103 R104 R105 R106 |
R92-0670-05
RK73FB2A222J R92-0670-05 RK73FB2A222J RK73FB2A392J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
0 0HM
2,2K 0 0HM 2,2K 3,9K |
L L |
1/10W
1/10W 1/10W |
||||
|
R107-111
R112 R113 R114 |
RK73FB2A473J
RK73FB2A223J RK73FB2A472J R92-0670-05 |
CHIP R
CHIP R CHIP R CHIP R |
47K
22K 4.7K 0 0HM |
J
J J |
1/10W
1/10W 1/10W |
||||
|
D1 ,2
IC51 Q1 Q2 Q51 |
1T33C
M54959FP 2SC2714(Y) 2SK582 2SC2714(Y) |
IC(FREQ SY
TRANSISTOR FET TRANSISTOR |
NTHESIZER F | LL) | |||||
|
952
953 9101,102 |
DTC144EK
2SC2712(Y) 2SC3324(B) |
DIGITAL TRA
TRANSISTOR TRANSISTOR |
ANSISTOR | ||||||
| ÷ | APC UN | IIT (X59-3130- | 00) | ||||||
|
C1
C2 C3 C4 C5 |
CK73FB1H102K
C92-0501-05 CK73FB1H472K CK73FB1H102K CK73FB1H472K |
CHIP C
CHIP-TAN CHIP C CHIP C CHIP C |
1000PF
1.5UF 4700PF 1000PF 4700PF |
KOXXX | 3MA. | ||||
| C6 | CK73FB1H102K | CH1P C | 1000PF | к | |||||
| E23-0471-05 | TERMINAL | ||||||||
|
R1
R2 R3 R4 ,5 R6 |
RD41FB2B222J
RD41FB2B102J RD41FB2B152J RD41FB2B153J RD41FB2B103J RD41FB2B122J |
CARBON
CARBON CARBON CARBON CARBON CARBON |
2.2K
1K 1.5K 10K 1.2K |
JJJJJ |
1/8W
1/8W 1/8W 1/8W 1/8W |
||||
|
Q1 ,2
Q3 |
FMW1
25A1162(Y) |
TRANSISTOR | |||||||
| MIC AMP | UNIT (X59-36 | 10-00) | - | ||||||
|
C1
C2 C3 C4 C5 |
CK73FF1E104Z
CK73GB1H102K CK73FB1E333K CC73GCH1H270J C92-0004-05 |
CHIP C
CHIP C CHIP C CHIP C CHIP C CHIP TAN |
0.1UF
1000PF 0.033UF 27PF 1.0UF |
Z,
K K J 16 |
WV |
U: PX(Far East, Hawaii) T: England M: Other Areas
UE : AAFES(Europe) X: Australia
* New Parts
PARTS LIST
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht geliefert.
MIC AMP UNIT (X59-3610-00) Ref. No. Address New Parts No. Description Desti- Renation mark 参照番号 位置 部品番号 向 備考 新 部品名/規格 仕 CK73FB1E333K 0.033UF 680PF 3300PF 82PF CK73GB1H102K E23-0471-05 TERMINAL RK73GB1J223J CHIP R 1/16W RK73GB1J561J 560 RK73GB1J470J RK73GB1J561J 560 0 OHM 390K 220K 180K RK73GB1J333J RK73FB2A473J 1/10W R12 R13 -15 1/16W 1/16W IC1 Q1 NJM4558M IC(OP AMP X2) TRANSISTOR E: Scandinavia & Europe K: USA P: Canada W:Europe TM-241A: K, P, M, M2 TM-241E: E, E2 U: PX(Far East, Hawaii) T: England M: Other Areas
4
4
-
UE : AAFES(Europe) X: Australia
Parts with the exploded numbers larger than 700 are not supplied.
PACKING
افي
ä,
TM-241A/E
ADJUSTMENT
REQUIRED TEST EQUIPMENT
- 1. DC V.M and Tester
-
1) High input impedance 2. RF VTVM (RF V.M)
- Input impedance : 1MΩ min., 2pF max. Voltage range : F.S = 10mV to 300V Frequency range : Up to 450MHz
- Frequency Counter (f. counter) Input sensitivity : Approx. 50mV Frequency range : Up to 450MHz
- DC Power Supply Voltage : 10V to 17V, variable Current: 11A min.
- 5. Power Meter 1) Measurement range: Approx. 60W, 3W, 1W 2) Input impedance : 50Ω 3) Frequency range : 450MHz
-
6. AF VTVM (AF V.M)
-
1) Input impedance : 1MΩ min.
- 2) Voltage range : F.S = 1mV to 30V3) Frequency range : 50Hz to 10kHz
-
1) Input impedance : 1MΩ min.
-
AF Generator (AG)
- 1) Output frequency : 100Hz to 10kHz 2) Output voltage : 0.5mV to 1V
-
8. Linear Detector
- 1) Frequency range : 450MHz
- 9. Spectrum Analyzer 1) Frequency range : 450MHz
- 10. Directional Coupler
-
11. Oscilloscope
- High sensitivity oscilloscope with horizontal input terminal
-
12. SSG
- 1) Frequency range : 144MHz band
- 2) Modulation: AM and FM MOD.
- 3) Output level : 0.1µV to 100mV.
-
13. Dummy Load
- 1) 8Ω, 5W (approx.)
-
14. Noise Generator
- Must generate ignition-like noise containing harmonics beyond 450MHz.
- 15. Sweep Generator
- 1) Sweep range : 144MHz bands
- 16. Tracking Generator
PREPARATION
1) Unless otherwise specified, knobs and switches should be set as follows Table 7 .
| POWER SW | ON | CALL | OFF |
|---|---|---|---|
| AF VOL VR | MIN | SHIFT/AL | OFF |
| SQL VOL VR | MIN | TONE/T. ALT | OFF |
| VFO | VFO | REV/STEP | OFF |
| MR | OFF | DR/DT | OFF |
Fig. 13 MIC terminals (view from front panel side)
- Use an insulated adjusting rod to adjust trimmers and coils.
- To prevent damaging SSG, never set the stand by switch to SEND while adjusting the receiver section.
- Be sure to turn the power switch OFF, before connecting the power cable to a power source.
- Meter and display section should be set as follows Fig. 14.
Fig. 14
ADJUSTMENT
COMMON SECTION ADJUSTMENT
| 1. The second second | 1. T. N. 202 | Mea | sureme | ent | Adj | ustment | A STREET STREET, STREE | |
|---|---|---|---|---|---|---|---|---|
| Item | Condition |
Test-
equipment |
Unit | Terminal | Unit | Parts | Method | Specifications/Remarks |
| 1, Setting |
1) Source voltage : DC 13.8V
POWER SW : OFF VOL VR : Full counter-clock- wise (CCW) SQL VR : CCW TX-RX unit VR3, 4 : CCW VR1 : Center |
|||||||
| 2. Reset |
1) Turn POWER SW ON while
holding down MR/M. |
Display 144.000 | ||||||
| 3. PLL |
1) RX VCO
FREQ. : 144.975 E,E 2 FREQ. : 146.000 K,P,M,M2 Receive. |
DVM
Dummy |
TX-RX
Rear panel |
TP2
ANT |
Check | 1.7 ~ 2.4V | ||
|
2) FREQ. : 136.000
K,P,M,M2 Receive. |
1.0V or more. | |||||||
|
3) TX VCO
FREQ. : 144.975 E,E 2 FREQ. : 146.000 K,P,M,M2 Transmit. |
3.2 ~ 3.8V | |||||||
|
4) FREQ. : 173.995 M2,E2
Transmit. |
10V or less. | |||||||
|
1) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 Transmit. |
f.counter
Power meter |
Rear
panel |
ANT | TX-RX | TC1 |
144.975MHz
E,E
2
146.000MHz K,P,M,M2 |
±100Hz |
RECEIVER SECTION ADJUSTMENT
| Mea | sureme | ent | Adj | ustment | ||||
|---|---|---|---|---|---|---|---|---|
| Item | Condition |
Test-
equipment |
Unit | Terminal | Unit | Parts | Method | Specifications/Remarks |
| 1. BPF |
1) FREQ. : 145.050 E,E
2
FREQ. : 146.040 K,P,M,M2 TX-RX unit VR1 : Center Connect the SSG to ANT. Connect the DC V.M to TP1, SSG output : -113dBm (0.5µV) SSG MOD : 1kHz SSG DEV : 3kHz |
DC V.M
SSG |
TX-RX | TP1 | TX-RX | L1~5 | Repeat for MAX. | |
| 2. Distortion |
1) FREQ. : 145.050 E,E
2
FREQ. : 146.040 K,P,M,M 2 SSG output:113dBm (0.5μV) SSG MOD : 1kHz SSG DEV : 3kHz |
Distortion
meter Oscilloscope |
Rear
panel |
SP | TX-RX | L6 | Repeat for MIN. |
Turn L6 core CCW until best
SINAD point obtained. |
ADJUSTMENT
| Mea | asurem | ent | Ad | justment | ||||
|---|---|---|---|---|---|---|---|---|
| Item | Condition |
Test-
equipment |
Unit | Terminal | Unit | Parts | Method | Specifications/Remark |
|
3. Receiving
sensitivity |
1) FREQ. : 145.050 E,E
2
FREQ. : 146.040 K,P,M,M2 SSG output : -123dBm (0.16μV) SSG MOD : 1kHz SSG DEV : 3kHz |
AF V.M
Oscilloscope |
Rear
panel |
SP | TX-RX | Check | SINAD 12dB or more. | |
|
2) FREQ. : 144.040
K,P,M,M2 FREQ. : 144.050 E,E 2 |
||||||||
|
3) FREQ. : 145.950 E,E
2
FREQ. : 147.940 K,P,M,M2 |
||||||||
| 4. S-meter |
1) FREQ. : 145.050 E,E
2
FREQ. : 146.040 K,P,M,M2 SSG output: -96dBm (3.6μV) SSG MOD : 1kHz SSG DEV : 3kHz |
LCD
(S-meter) |
TX-RX | VR1 | Adjust so that all the signal-strength segments go on, then the last segment goes off | |||
|
2) SSG output:
—95 dBm (4µV) |
Check | All S-meter segments on. | ||||||
| 3) SSG: OFF | 1 | - | Check | S-meter off. |
TRANSMITTER SECTION ADJUSTMENT
| Mea | ent | Adj | ustment | |||||
|---|---|---|---|---|---|---|---|---|
| ltem | Condition |
Test-
equipment |
Unit | Terminal | Unit | Parts | Method | Specifications/Remarks |
| 1-1. APC |
1) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 |
Power
meter Ammeter |
Rear
panel |
ANT | Check | 57W or more. | ||
| Transmit. | - | ON AIR LED on. | ||||||
|
2) FREQ. : 145.975 E,E
2
FREQ. : 147.995 K,P,M,M2 Transmit. |
TX-RX | VR4 | 54W | ±1W, 11A or less. | ||||
|
3) FREQ. : 144.000
Transmit. |
Check |
49 ~ 59W
11A or less. |
||||||
|
4) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 Transmit. |
Read RF meter | All RF meter LEDs on. | ||||||
|
1-2. MID
power |
1) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 LOW SW: PUSH Transmit. |
TX-RX | VR5 |
12W
Read RF meter |
±1W.
10 RF meter LEDs on. |
|||
|
1-3. LOW
power |
1) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 LOW SW: PUSH Transmit. |
Check
Read RF meter |
3.0 ~ 8.0W
6 RF meter LEDs on. |
ADJUSTMENT
ألحي
÷.
| Mea | ent | 1. | Adj | justment | had a lot of the second | |||
|---|---|---|---|---|---|---|---|---|
| Item | Condition |
Test-
equipment |
Unit | Terminal | Unit | Parts | Method | Specifications/Remarks |
| 2. DEV. |
EV. 1) FREQ. : 144.975 E,E
2
FREQ. : 146.000 K,P,M,M2 AG: 1kHz, 28mV E,E 2 AG : 1kHz, 50mV K,P,M,M2 Transmit. |
Rear
panel |
ANT | TX-RX | VR3 |
±4.4kHz
(Read higher abso- lute value of + or – value) |
±200Hz
Check for detected waveform. |
|
|
2) AG: 1kHz, 2.8mV E,E
2
AG: 1kHz, 5.0mV K,P,M,M2 |
Check | ±2.2 ~ 3.6kHz | ||||||
|
3) DTSS
AG: 1.6 kHz 175 mV (CN5 INPUT) |
Check | ±2.5 kHz or more | ||||||
| 3. Protection |
1) FREQ. : 145.975 E,E
2
FREQ. : 147.995 K,P,M,M2 ANT : OPEN Transmit. |
Ammeter | Check | 11A or less. | ||||
| 4-1. TONE |
1) FREQ. : 145.250
TONE : ON Transmit. |
Linear
detector Oscilloscope |
Rear
panel |
ANT | Check | DEV. : ±0.5 ~ 1.0kHz | ||
| 4-2. TONE |
1) FREQ. : 144.975 E,E
2
Transmit. |
Power
meter |
TONE SW of MIC
: ON. |
DEV. : ±2.5 ~ 5.0kHz | ||||
Adjustment Points (Top View)
LCD ASS'Y (B38-0330-05) Component side view
TM-241A/E circuit diagram
Q1:2SC2714(Y) Q2:2SK582
PLL (X58-3470-00) (B/2) Component side view
PLL (X58-3470-00) (A/2) Foil side view
PLL (X58-3470-00) (A/2) Component side view
M54949FP
2SK582
PC BOARD VIEW/CIRCUIT DIAGRAM
TM-241A/E
32
MIC AMP (X59-3610-00) MIC AMP (X59-3610-00)
Q1 : 25C4116(Y) IC1 : NJM4558M
APC (X59-3130-00) Component side view MIC AMP (X59-3610-00) Foil side view
Refer to the schematic diagram for the values of resistors and capacitors.
TM-241A/E PC BOARD VIEWS
TX-RX UNIT (X57-369X-XX) Component side view 0-11: TM-241A (K,P) 0-21: TM-241A (M) 0-22: TM-241A (M2) 2-71: TM-241E (T,E) 2-72: TM-241E (E2)
IC1: KCD04 IC3: #PC1241H IC4: KCC02 IC5: TC9174F IC6: NJM78L05UA IC7: LA5010M IC8: KCB05 IC9: MC7808CT IC201: IC201 Q,21: 2SK208(Y) Q,10,16, ~18,20,27,206 ~ 208: 2SC2712(Y) Q9: FMG2 Q12,19: 2SD1757 (K) Q13,14: 2SB1119S Q15: DTC144WK Q23; D8,9,203: ISS184 D11,202: ISS181 D12: MI407 D13: MI308 D14,15: ISS226 D16: DSA3A1 D204,206,207,211: ISS187 D205: ISS193
TX-RX UNIT (X57-3310-XX) Foil side view
0-11: TM-241A (K,P) 0-21: TM-241A (M) 0-22: TM-241A (M2) 2-71: TM-241E (T,E) 2-72: TM-241E (E2)
75116GF-728-3BE IC202 : NJM78L06UA IC301 : S-AV17 Q1 : 3SK184(S) Q4 : 3SK131(V12) Q5,22 : 2SC2714(Y) 4 : DTC124EK Q25 : 2SD1406 (Y) Q26 : 2SB1302S Q201~204 : 2SA1519 D209,210 : MA141A D212 : 02CZ7.5(X,Y)
TM-241A/E :
TERMINAL FUNCTIONS
| No. | No. | Name | Terminal Function |
Connector
No. |
Terminal
No. |
Terminal
Name |
Terminal Function | ||
|---|---|---|---|---|---|---|---|---|---|
| TX-F | X UNIT | (X57-369X-XX) (A/2) | CN202 | 1 | Е | GND. | |||
| CN1 | 1 | E | GND | - | 2 | В | +13.8V. | ||
| 0110 | 2 | SP | Speaker input. | 3 | PSW |
Power switch control output
(From CPU). |
|||
| CN2 | 1 | BZZ | 4 | SB | Switched B | ||||
| 2 | Е | GND. | 5 | 8C | Common +8V | ||||
| 3 | VI | Voice memory input. | 6 | BZ | Been output (From CPLI) | ||||
| 4 | VO | Voice memory output. | 7 | Δ2 | Audio output | ||||
| 5 | VOA | Power supply for voice memory | , | 1.54 | |||||
| CN3 | 1 | F | GND | 8 | Δ1 | Audia isput (to AF VOL). | |||
| 2 | NC | a | E | CND | |||||
| 3 | ES1 | Shift register (ICE) on ship | 10 | TO | GND. | ||||
| Δ | NC | Sinic register (ICS) enable. | 11 | NAE | Tone output (From IC203). | ||||
| 5 | ED1 | PLL coshie | 10 | IVIE | MIC GND. | ||||
| E | CV | PLL enable. | 12 | IVIIC | Mic output (From mic jack). | ||||
| 7 | DT | FLL CIOCK. | 13 | E | GND. | ||||
| 0 | DET | PLL data. | CN203 | 1 | CK | Serial clock output (From CPU P21). | |||
| 0 | DEI | CICSS detector output | 2 | DT | Serial data output (From CPU P22). | ||||
| 10 | RU | Audio output. | 3 | VCK | DRS unit connect check. | ||||
| 10 | SC | Squeich busy control output. | 4 | GND | GND. | ||||
| 11 | SQ | Squeich output | 5 | D8 | DRS unit data. | ||||
| 12 | SM | S-meter output. | 6 | D1 | DRS unit data. | ||||
| 13 | E | GND. | 7 | D2 | DRS unit data. | ||||
| CN4 | 1 | E | GND. | 8 | D4 | DRS unit data | |||
| 2 | В | +13.8 V. | CN204 | 1 | DST | ||||
| 3 | PSW | Power switch control input. | CIN204 | 2 | EC | Commission 1511 | |||
| 4 | SB | Switched B. | 2 | DV | Common +5V. | ||||
| 5 | 8C | Common +8V | 3 | DV | DTMF signal detector. | ||||
| 6 | BZ | Beep input (To AF IC from CPLI) | 4 | VOB | DRS unit VOB output. | ||||
| 7 | A2 | Audio input | 5 | VOA | DRS unit VOA output. | ||||
| (To electronic volume from AE VOL) | 6 | RD | DRS unit RD output. | ||||||
| 8 | A1 | / | WR | DRS unit WR output | |||||
| 9 | F | GND | 8 | ACL | DRS unit RESET output. (ACL) | ||||
| 10 | TO | Tone input | 9 | STBY | DRS unit STBY output. | ||||
| 11 | ME | MIC CND | 10 | OE | DRS OE, DTSS EN | ||||
| 12 | MIC | Mic GND. | CN205 | 1 | DT | LCD driver data output | |||
| 12 | E | CND (TO MIC AMP unit). | 2 | CK | LCD driver clock output | ||||
| 15 | C | GND. | 3 | CE | LCD driver enable output | ||||
| TX-R | X UNIT | (X57-369X-XX) (B/2) | 4 | C5 | +5V. | ||||
| N201 | 1 | E | GND. | 5 | E | GND. | |||
| 2 | NC | 6 | FC | Function control | |||||
| З | ES1 | Shift register enable | 7 | NC | Euloction Jame P | ||||
| NC | (From CPU IC201). | 9 | LAMP | Lamn R | |||||
| 4 | FDI | 10/202 | - | CAID | |||||
| C | EPI | FLL enable (From CPU IC201). | VV201 | 1 | GND | GND. | |||
| 0 | CK | PLL clock (From CPU IC201). | 2 | RD | CTCSS unit voice de-modulation input, | ||||
| / | DT | PLL data (From CPU IC201). | 3 | C5 | Common +5 V. | ||||
| 8 | DET | CTCSS detector output. | 4 | DET | CTCSS unit tone matching input. | ||||
| 9 | RD | Audio input (CPU IC201). | 5 | CTC | CTCSS unit clock output. | ||||
| 10 | SC | Squelch busy control input. | 6 | CTD | CTCSS unit data output. | ||||
| To CPU IC201) | 7 | CTS | CTCSS unit enable output. | ||||||
| 11 | SQ | Squelch input (To CPU IC201) | 100 | ||||||
| 12 | SM S | S-meter input (To CPU IC201) | |||||||
TM-241A/E
BLOCK D
TM-241A/241E
AGRAM
TM-241A/E
* K, P only
LEVEL DIAGRAM
AG is set so that MIC input becomes 3kHz DEV at 1kHz M 2. Transmitting frequency : 145.06 MHz
TM-241A/E DRU-1 (DIGITAL RECORDING UNIT)
DRU-1 CIRCUIT DESCRIPTION
1. Overview
The DRU-1 is a digital recording and playback unit designed to be installed inside the TM-241 A/E series. This unit has the following features:
- Recording received audio (for output to the internal speaker) or transmit audio (microphone input)
- Outputting recorded audio to the internal speaker or outputting recorded audio as modulating signals during transmission
- Built-in lithium battery back-up for maintaining DRU-1 contents
- DTSS and paging code reception.
2. Operations
Recording received audio (for output to the internal speaker)
A received signal from the VO pin is fed into pin 1 (0Y) of the multiplexer IC1 (TC4052BF). It is then fed into pin 59 (MIC IN) of IC3 (TC8830F) via pin 3 (Y). The signal is amplified approx. 26dB by a mic amplifier in IC3, and output via pin 60 (C1). The signal from pin 60 is fed into pin 63 (C2) and amplified approx. 20dB. The amplified signal is applied to pin 64 (MIC OUT) and pin 65 (ADI).
Recording transmit audio (microphone input)
Microphone input from the VI pin is amplified by Q5, and fed into pin 2 (2Y) of the multiplexer IC1 (TC4052BF). It is then supplied to IC3 (TC8830F) via pin 3 (Y) and recorded in the same way as in recording received sound.
DRU-1 DESCRIPTION OF COMPONENTS ACCESSORY UNIT (X42-3010-00)
| Component | Use/Function | Description |
|---|---|---|
| IC1 | Multiplexer | See DRU-1 circuit description |
| IC2 | DTMF decode | |
| IC3 | Audio recording and playback | See DRU-1 semiconductor data |
| IC4~7 | S-RAM | |
| Q5 | AF amplification | Mic input amplification |
| Q6 | AF amplification | Playback sound amplification |
| D1 | Reverse current prevention | |
| D2 | Reverse current prevention | Back-up. |
Outputting recorded audio to the internal speaker
D/A convertor output from pin 66 (DAO) of IC3 (TC8830F) is passed through a CR filter, and amplified by Q6. The amplified signal is then fed into pin 13 (X) of the multiplexer IC1 (TC4052BF), and output to the VO pin via pin 14 (1X).
Outputting recorded audio as modulating signals during transmission
When sound recorded in the DRU-1 is played during transmission, the same operations as written above in outputting recorded audio to the internal speaker occur. That is, D/A convertor output from pin 66 (DAO) of IC3 (TC8830F) is passed through a CR filter, amplified by Q6, and fed into pin 13 (X) of the multiplexer IC1 (TC4052BF). The sound, however, is output via pin 11 (3X).
|
VOA
(pin 10) |
VOB
(pin 9) |
On channel | |
|---|---|---|---|
| Output to speaker | н | L | 1X (pin 14) |
| Output during transmission | н | н | 3X (pin 11) |
| Received audio recording | L | L | OY (pin 1) |
| Transmit aidop recording | L | Н | 2Y (pin 2) |
Table 1 IC1 : TC4052BF operations
DTSS and paging code reception
The DTMF signal input from the VO pin is amplified by Q1 and input to pin 12 of DTMF decoder IC2 (LR4102N). When the DTMF signal is input to IC2, pin 20 (DV pin) is made high. A DTMF code is then output to pins 1 (D1), 24 (D2), 23 (D4), and 22 (D8) of IC2. The CPU can receive the DTMF signal by detecting the DTMF signal input from the DV pin and reading D1, D2, D3, and D4 data.
DRU-1 (DIGITAL RECORDING UNIT)
2. DTMF DECODER: LR4102N (IC2)
Pin connection
• Pin description
| Pin No. | Name | 1/0 | Function | Pin No. | Name | 1/0 | Function |
|---|---|---|---|---|---|---|---|
| 1 | D1 | Ø | DTMF data output | 13 | GNDA | - | Analog GND |
| 2 | H/B | 16 digit cord setting | 14 | OSCOUT | 0 | X-tal output | |
| 3 | EN | - T | Output enable | 15 | OSC | 1 | X-tal input |
| 4 | GND | - | Digital GND (GND) | 16 | NC | - | NC |
| 5 | NC | - | NC | 17 | NC | - | NC |
| 6 | IN1633 | Ĩ. | Valid 1633 Hz (GND) | 18 | XEN | 1 | X-tal enable |
| 7 | Vap | Power supply | 19 | ATB | 0 | NC | |
| 8 | NC | NC | 20 | DV | 0 | Data varied | |
| 9 | S1 | - |
Bypass (Connected to ground by a
0.01 µF capacitor.) |
21 | CLDV | 1 | Data varied clear |
| 10 | S2 | - |
Bypass (Connected to ground by a
0.01 µF capacitor.) |
22 | D8 | Q | DTMF data output |
| 71 | NC | - | NC | 23 | D4 | 0 | DTMF data output |
| 12 | ANALOG IN | - I - | DTMF signal input | 24 | D2 | 0 | DTMF data output |
TM-241A/E
DRU-1 (DIGITAL RECORDING UNIT)
Block diagram
DRU-1 SEMICONDUCTOR DATA
1. Audio recording and playback : TC8830F (IC3)
Terminal function
| Pin No. | Pin name | 1/0 | Function | Pin No. | Pin name | 1/0 | Function |
|---|---|---|---|---|---|---|---|
| 1 | FIL OUT | 0 | Not used. | 41 | X OUT | 0 | 512kHz oscillation circuit. |
| 2 | NC | - | Not connected. | 42 | 256K | 1 | 64K/256K RAM select, |
| 3 | TEST | - | Not used. | "H" when 256K used. | |||
| 4 | D7 | 1/0 | RAM data I/O. | 43 | R/W | 0 | RAM read/write output. |
| 5 | NC | - | Not connected. | 44 | ALE | - | Not used. |
| 6 | D6 | 1/0 | RAM data I/O. | 45 | WR | 1 | Write pulse input. |
| 7 | NC | - | Not connected. | 46 | RD | 1 | Read pulse input. |
| 8 | D5 | 1/0 | RAM data I/O. | 47~50 | PH3~PH0 | - | Not used. |
| 9 | NC | - 1 | Not connected. | 51~54 | P3~P0 | 1/0 | Data bus. |
| 10 | D4 | 1/0 | RAM data I/O. | 55 | EOS | - | Not used. |
| 11,12 | NC | - | Not connected. | 56 | ACL | 1 | Reset signal input. |
| 13-16 | D3~D0 | 1/0 | RAM data I/O. | 57 | CPUM | 1 | "H" when CPU control enabled. |
| 17~19 | A14~A12 | 0 | RAM address output. | 58 | Vref | 0 | Analog circuit reference voltage output. |
| 20 | VSS1 | - | GND. | 59 | MIC IN | 1 | Mic amp. 1 input. |
| 21~26 | A11~A6 | 0 | RAM address output. | 60 | C1 | 0 | Mic amp. 1 output. |
| 27 | VDD | - | Power supply. | 61 | VDD | - | Power supply. |
| 28~33 | A5~A0 | 0 | RAM address output. | 62 | VSS2 | - | GND. |
| 34 | CE | - | Not used. | 63 | C2 | T | Mic amp. 2 input. |
| 35~38 | CE1~CE4 | 0 | RAM chip enable. | 64 | MIC OUT | 0 | Mic amp. 2 output. |
| 39 | STBY | 1 | Minimum current standby when standby | 65 | ADI | 1 | Audio analysis circuit input. |
| 1.1 | - | input is "H". | 66 | DAO | 0 | D/A convertor output. | |
| 40 | X IN | 1 | 512kHz oscillation circuit. | 67 | FIL IN | 1 | Not used. |
TM-241A/E DRU-1 (DIGITAL RECORDING UNIT) DRU-1 PARTS LIST
* New Parts Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Telle ohne Parts No. werden nicht geliefert.
| Ref. No. | Address |
New
Parts |
Parts No. | Desc | ription |
Desti-
nation |
Re-
marks |
|---|---|---|---|---|---|---|---|
| 参照誉号 | 位置 | 新 | 部品養考 | 31 11 11 | 名/規 格 | 任 问 | 118-15 |
| DRU-1 | |||||||
| - |
842-3317-04
850-8290-00 |
LABEL
INSTRUCTION MA |
NUAL | ||||
|
G10-0666-04
G10-0679-04 G13-0913-04 |
NON-WOVEN FABR
NON-WOVEN FABR FORMED PLATE |
HC
HC |
|||||
| *** |
H01-8249-03
H03-2772-04 H21-0704-04 H25-0029-04 H25-0710-04 |
ITEM CARTON BO
NUTER PACKING PROTECTION SHE PROTECTION BAG PROTECTION BAG |
X
CASE ET |
||||
| NB7-2606-46 | BRAZIER HEAD T | APTITE SCREW | |||||
| X42-3010-00 | ACCESSORY UNIT | ||||||
| ACCESSORY | UNIT (X42-3010- | 00) | |||||
|
C1
C2 C3 C4 -6 C7 |
CK73FB1H103K
CK73FB1H102K CK73FF1E154Z CK73FF1E154Z CK73FB1H103K CK73EF1C105Z |
CHIP C C
CHIP C D CHIP C C CHIP C C CHIP C D |
). 010UF K
1000PF K ). 15UF Z ). 010UF K . 0UF Z |
||||
|
C8 -10
C11 C12 C13 +14 C15 |
CK73FB1H103K
CK73FF1E104Z CK73FB1H103K CK73FB1H102K CK73FB1H102K CK73FF1E104Z |
CHIP C C
CHIP C C CHIP C C CHIP C I CHIP C I CHIP C C |
0.010UF K
0.10UF Z 0.010UF K 0000PF K 0.10UF Z |
||||
|
C16
C17 C19 C20 C21 ,22 |
CK73FB1H103K
CK73FF1E104Z CK73FB1H103K CK73FB1H102K CC73FB1H102K CC73FSL1H101J |
CHIP C C
CHIP C C CHIP C C CHIP C C CHIP C C |
D. DIOUF K
D. 10UF Z D. 010UF K 1000PF K 1000PF J |
||||
|
C23
C24 C25 C26 C27 |
CK73FB1H103K
C92-0010-05 CK73EB1H104K CK73FB1H103K CC73FSL1H101J |
CHIP C C
CHIP TAN C CHIP C C CHIP C C CHIP C C |
D.010UF K
5.8UF 6.3WV 0.10UF K 0.010UF K 100PF J |
||||
| C28 | CK73FF1E1D4Z | CHIP C | 1.10UF Z | ||||
|
EN1
CN2 CN3 W1 W2 |
**** |
E40-5207-05
E40-5206-05 E40-5181-05 E31-6005-05 E31-6006-05 |
PIN CONNECTOR
PIN CONNECTOR PIN CONNECTOR CONNECTING WI CONNECTING WI |
RE
RE |
|||
| WЗ | * | E31-6007-05 | CONNECTING WI | RE | |||
|
F20-0520-04
F20-0521-04 |
INSULATING BU |
ARD
ARD |
|||||
|
X1
X2 |
* |
L77-1398-05
L78-0050-05 |
CRYSTAL RESON
RESONATOR |
ATOR 3.579545MH
512KHZ |
Z | ||
|
R1
R2 R3 R4 R5 |
ľ |
RK 73F82A103J
RK 73F82A392J RK 73F82A103J RK 73F82A105J RK 73F82A105J RK 73F82A102J |
CHIP R
CHIP R CHIP R CHIP R CHIP R |
10k .) 1/1
3.9k J 1/1 10k J 1/1 1.0M J 1/1 1.0k J 1/1 |
E Scandinavia & Europe K. USA P. Canada W:Europe
U: PX(Far East Hawaii) T England M. Other Areas
UE AAFES(Europe) X Australia
A indicates safety critical components
DRU-1 (DIGITAL RECORDING UNIT) Parts without Parts No. are not supplied.
* New Parts
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Telle ohne Parts No. werden nicht gellefert.
| Address | New | Parts No. | D | escription | Desti- | Re- | ||
|---|---|---|---|---|---|---|---|---|
| 位置 | 新 | 部 品 폴 号 | 部品 | 名/規 | 格 |
nation
仕 向 |
mar x
備考 |
|
|
R92-0670-05
RK73FB2A223J RK73FB2A102J RK73FB2A105J R92-0670-05 |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
0 0HM
22K 1.0K 1.0M 0 0HM |
J
J |
1/10W
1/10W 1/10W |
1 | |||
|
RK73FB2A223J
R92-D670-D5 RK73FB2A222J RK73FB2A472J RK73FB2A472J RK73FB2A104J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
22K
0 0HM 2.2K 4.7K 100K |
L
L L L |
1/10W
1/10W 1/10W 1/10W |
||||
|
RK73FB2A105J
RK73FB2A103J RK73FB2A105J RK73FB2A562J RK73FB2A562J RK73FB2A104J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
1. OM
10K 1. OM 5. 6K 100K |
J |
1/10W
1/10W 1/10W 1/10W 1/10W |
||||
|
RK73FB2A103J
RK73FB2A102J RK73FB2A564J RK73FB2A564J RK73FB2A273J RK73FB2A683J |
CHIP R
CHIP R CHIP R CHIP R CHIP R CHIP R |
10K
1.0K 560K 27K 68K |
L |
1/10W
1/10W 1/10W 1/10W 1/10W |
||||
|
RK73FB2A105J
RK73FB2A222J RK73FB2A224J R92-0670-05 RK73FB2A220J |
CHIP R
CHIP R CHIP R CHIP R CHIP R |
1.0M
2.2K 220K 0 0HM 22 |
J
J J |
1/10W
1/10W 1/10W |
||||
| RK73FB2A394J | CHIP R | 390K | J | 1/10W | ||||
| * * |
1SS184
TC4052BF LR41D2N TC8830F HM62256LFP-15T |
DINDE
IC(4CH MPX/I IC IC IC IC |
)E-MPX) | |||||
|
2SC2712(BL)
DTC144EK 2SC2712(BL) |
TRANSISTOR
DIGITAL TRAN TRANSISTOR |
SISTOR | ||||||
| W07-D326-05 | LITHIUM BAT | TERY | ||||||
|
Address
位 重 |
Address New
Parts 新 |
Address
New
Parts Parts No. 位 正 第 第 8 3 9 位 正 第 第 9 8 3 9 位 正 第 第 9 位 正 第 第 9 |
Address
PartsNew PartsParts No.D位11111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111
Address
|
bris New parts Parts No. Description 11 11 15 16 17 18 16 17 18 15 16
Address
Ner
|
Parts Parts No. Description 11 11 12 13 14 15 14 15 15 16 17 10 11 <
Address
New
|
Parts No. Description #
Address
New
|
Print Parts No. Description Desti- mit R 11 |
U: PX(Far East, Hawaii) T-England M. Other Areas
UE: AAFESIEurope) X. Australia
TM-241A/E dru-1 (digital recording unit)
DRU-1 PC BOARD VIEWS ACCESSORY UNIT (X42-3010-00) Component side view
IC1 : TC4052BF IC2 : LR4102N IC3 : TC8830F IC4~7 : HM62256LFP-15T Q5,6 : 2SC2712(BL) D1,2 : 1SS184
ACCESSORY UNIT (X42-3010-00) Foil side view
DRU-1 SCHEMATIC DIAGRAM
(X42-3010-00) (A/2)
(X42-3010-00) (A/2)
| ICI | : TC4052BF | Q1~3,5,6 | : 2SC2712(BL) |
|---|---|---|---|
| IC 2 | LR4102N | 04 | DTCI44EK |
| IC 3 | : TC8830F | D1.2 | : 155184 |
| IC 4~7 | : HM62256LFP-15T |
TM-241A/E :
DTU-2 (DTMF UNIT)
DTU-2 EXTERNAL VIEW
DTU-2 PARTS LIST
| Re 5 No. |
New
Parts |
Parts No. | Description |
|---|---|---|---|
| C1 | CK73FB1E104K | Chip C 0.1 µF K | |
| C2 | CC73GCH1H100D | Chip C 10 pF D | |
| C3,4 | CC73GCH1H330J | Chip C 33 pF J | |
| C5~8, 10 | CK73GB1E103K | Chip C 0.01 µF K | |
| C13~16 | CK73GL1E103K | Chip C 0.01 uF K | |
| C9 | CK73GB1E822K | Chip C 0.0082 uF K | |
| C10 | CK73GB1E322K | Chip C 0.0033 uF K | |
| C11 | CC73GSL1H101J | Chip C 100 pF J | |
| E37-0033-05 | Connecting cable (6P) | ||
| E40-5188-05 | Pin ass'v socket (11P) | ||
| X1 | L78-0061-05 | CERAMIC RESONATOR | |
| (3.58 MHz) | |||
| R1~14 | RK73GB1JxxxJ | Chip R | |
| Q1 | DTC114EU | Digial transistor | |
| Q2.3 | 2SC4116 (Y) | Digital transistor | |
| IC1 | TP5088WM | IC | |
| IC2 | LC7385M | IC | |
| IC3 | BU4066BF | IC |
TM-241A/E
DTU-2 (DTMF UNIT)
DTU-2 PC BOARD
Component side view
Foil side view
SCHEMATIC DIAGRAM
MC-44DM/MC-44DME (MULTI FUNCTION MICROPHONE WITH AUTOPATCH)
MC-44DM/MC-44DME SCHEMATIC DIAGRAM
MC-44DM/MC-44DME PARTS LIST
| Ref. No. | New parts | Parts No. | Description | ||
|---|---|---|---|---|---|
| * | A02-0898-18 | Case (Front) | DTMF | м | |
| • | A20-0899-18 | Case (Front) | DTMF (With TONE) | W | |
| A02-0901-08 | Case (Rear) | DTMF | |||
| * | B50-8293-18 | Instruction ma | nual | ||
| E30-2149-08 | Curl cord | ||||
| G13-0933-08 | Cushion | ||||
| K29-3165-08 | Knob | PTT | |||
| K29-3167-08 | Key top | DTMF | |||
| K29-3168-18 | Knob | UP | |||
| 1 | K29-3169-18 | Knob | DOWN | ||
| SW2 | S31-1422-08 | Slide switch | LOCK | ||
| SW1 | S50-1431-08 | Micro switch | PTT | ||
| S7, 8 | S59-1409-28 | Switch Ass'y | UP, DOWN | ||
| T91-0383-08 | Microphone el | ement (Condenser microphone) |
TM-241A/E MC-44 (MULTI FUNCTION MICROPHONE)
MC-44 SCHEMATIC DIAGRAM
MC-44 PARTS LIST
| Ref. No. | New parts | Parts No. | Description | |
|---|---|---|---|---|
| A02-0896-18 | Case (Front) | |||
| A02-0900-08 | Case (Rear) | |||
| • | B50-8293-18 | Instruction ma | nual | |
| • | E30-2149-08 | Curl cord | ||
| G13-0933-08 | Cushion | |||
| K29-3165-08 | Knob | PTT | ||
| K29-3168-18 | Knob | UP | ||
| K29-3169-18 | Knob | DOWN | ||
| K29-3170-08 | Knob | CALL, VFO, MR, PF | ||
| SW2 | S31-1422-08 | Slide switch | LOCK | |
| SW1 | S50-1431-08 | Micro switch | PTT | |
| S7, 8 | ٠ | S59-1409-28 | Switch Ass'y | UP, DOWN |
| T91-0383-08 | Microphone el | ement (Condenser microphone) |
MC-44E (MULTI FUNCTION MICROPHONE)
TM-241A/E
MC-44E SCHEMATIC DIAGRAM
MC-44E PARTS LIST
| Ref. No. |
New
parts |
Parts No. | Description | |
|---|---|---|---|---|
| • |
A02-0897-18
A02-0900-08 |
Case (Front)
Case (Rear) |
With TONE | |
| B50-8293-18 | Instruction ma | nual | ||
| E30-2149-08 | Curl cord | |||
| G13-0933-08 | Cushion | |||
| K29-3165-08 | Knob | PTT | ||
| K29-3168-18 | Knob | UP | ||
| K29-3169-18 | Knob | DOWN | ||
| K29-3170-08 | Knob | 1750, VFO, MR, PF | ||
| SW2 | S31-1422-08 | Slide switch | LOCK | |
| SW1 | S50-1431-08 | Micro switch | PTT | |
| S7, 8 | S59-1409-08 | Switch Ass'y | UP, DOWN | |
| ÷. | T91-0383-08 | Microphone el | ement (Condenser microphone) |
TM-241A/E
TSU-6 (CTCSS UNIT)
TSU-6 EXTERNAL VIEW
TSU-6 REFERENCE DATA
TH-25's condition and MN4094BS (IC2) relationship
| CTCSS | TONE | TX/RX | MN4094BS terminal | |||||
|---|---|---|---|---|---|---|---|---|
| switch | switch | Q5 | 06 | 01~4,7,8 | ||||
| OFF | TX | L | н | L | ||||
| 055 | OFF | RX | L | н | L | |||
| OFF | - | TX | L | L | See table 2 | |||
| ON | RX | L | H | L | ||||
| 055 | TX | L | L | |||||
| ON | OFF | RX | н | L | 1 | |||
| TX | L | L | See table 2 | |||||
| UN | RX | н | L | |||||
Q1 ~ 4, 7, 8 Tone frequency setting
Q5 : TX/RX switch for MN6520 (IC1). "H" RX. "L" TX.
Q6 : Power switch for MN6520 (IC1). "H" : OFF, "L" ON.
Table 1
Tone frequency and MN6520 (IC1) relationship
TSU-6 PARTS LIST
| Ref. No. |
New
Parts |
Parts No. | D | escription | |
|---|---|---|---|---|---|
| CTCSS UNIT (X5 | 2-3100-00 | ) | |||
| C1 | CK73FB1H102K | Chip C | 1000pF | к | |
| C2 | C92-0010-05 | Tantal | 6.8µF | 6.3WV | |
| C3 | C92-0006-05 | Tantal | 3.3µF | 4.0WV | |
| C4, 5 | 1.1 | CK73EB1E104K | Chip C | 0.1µF | κ |
| C6 | CK73EB1H223K | Chip C | 0.022µF | к | |
| C7 | CK73EB1E104K | Chip C | 0.1µF | к | |
| C8,9 | CC73FCH1H150J | Chip C | 15pF | 1 | |
| C10 | CK73FB1H102K | Chip C | 1000pF | ĸ | |
| C11 | CK73EB1E104K | Chip C | 0.1µF | к | |
| C12 | C92-0507-05 | Chip tan. | 4.7µF | 6.3WV | |
| C13 | • | C92-0510-05 | Chip tan. | 3.3µF | 4.0WV |
| • | E40-5121-05 | Pin conne | ctor (10P) | ||
| ×1 | L77-1313-05 | X'tal resor | hator 4.194 | 304MHz | |
| R1-10 | BK73FB2A000J | Chip resist | or | ||
| R12-14 | RK73FB2A000J | Chip resist | or | ||
| VRI | R12-3460-05 | Trimming | pot. 33kΩ | 2 | |
| Q1 | DTC144TK | Digital tra | nsistor | ||
| 02 | DTA114EK | Digital tra | nsistor | ||
| 03 | 2SC2712(GR) | Chip trans | istor | ||
| IC1 | MN6520 | 1C | |||
| 1C2 | MN4094BS | IC |
TSU-6 FINE ADJUSTMENT OF TONE FREQUENCY
The tone frequency can be fine adjusted with an interval of 0.5% step over the range of 0 to +1.5%. Ground the T1 (pin 10) and T2 (pin 9) of IC1 to obtain the desired frequency.
| / | T1 | T2 |
|---|---|---|
| 0% | х | × |
| +0.5% | 0 | × |
| +1.0% | × | 0 |
| +1.5% | 0 | 0 |
able 3
| Tone | 22 | CE | 64 | 20 | 0 | |
|---|---|---|---|---|---|---|
| frequency | 56 | 55 | 54 | 53 | 52 | 51 |
| (Hz) | 01 | 1 02 | 02 | 00 | ||
| 67.0 | - ui | 42 | 43 | 04 | 47 | 00 |
| 71.0 | L | - | L | |||
| 71.9 | L | H | н | н | L | - |
| 74,4 | L. | H | H | L | H | H |
| 77.0 | L | н | H | L | н | L |
|
79.7
02.5 |
L | E C | H | L | L | H |
| 82.5 | L | н | H | - | L | |
| 85.4 | L | H | L | н | H | H |
| 88.5 | L | н | L | н | H | L |
| 91,5 | L | H | L | н | L | H |
| 94.8 | H | н | H | L | L | H |
| 100.0 | H | н | н | L | L | L |
| 103.5 | н | н | L | н | н | н |
| 107.2 | н | н | L | н | н | L |
| 110.9 | н | н | L | н | L | н |
| 114.8 | н | н | L | н | L | L |
| 118.8 | н | н | L | L | н | н |
| 123.0 | н | н | L | L | н | L |
| 127.3 | н | н | L | L | L | н |
| 131.8 | н | н | L | L | L | L |
| 136.5 | н | L | н | н | н | н |
| 141.3 | н | L | н | н | н | L |
| 146.2 | н | L | н | н | L | н |
| 151.4 | н | L | н | н | L - | L |
| 156.7 | н | L | н | L | н | н |
| 162.2 | н | L | н | L | н | L |
| 167.9 | н | L | н | L | L | н |
| 173.8 | н | L | н | L | L | L |
| 179.9 | н | L | L | н | н | H |
| 186.2 | н | L | L | н | н | L |
| 192.8 | н | . L . | L | H | L | н |
| 203.5 | н | L | L | H | L | L |
| 210.7 | н | L | L | . L | н | н |
| 218.1 | н | L | L | L | н | L |
| 225.7 | н | L | L | L | L | Н |
| 233.6 | н | L | L | L | L | L |
| 241.8 | E | н | н | н | н | Н |
| 250.3 | L | н | н | H | н | L |
TM-241A/E
TSU-6 (CTCSS UNIT)
SPECIFICATIONS
General
| General | |
|---|---|
| Frequency range |
136 to 174 MHz; TM-241A (M2), TM-241E (E
2
)
144 to 148 MHz; TM-241A (K, P, M) |
| 144 to 146 MHz: TM-241E (E) | |
| Mode | F3E (FM) |
| Antenna impedance | 50Q |
| Power requirements | 13.8 V DC ±15% (11.7 to 15.8) |
| Ground | Negative |
| Frequency stability | Less than ±10ppm |
| Current drain | |
| Transmit mode | Less than 11A |
| Receiver mode with no signal | Less than 0.6A |
| Operating temperature | -20°C to +60°C (-4°F to +140°F) |
|
Dimensions (W x H x D)
(Projection included) |
140 x 40 x 160 mm (5-1/2" x 1-37/64" x 6-19/64")
140 × 40 × 172 mm (5-1/2" × 1-37/64" × 6-25/32 |
| Weight | 1.2kg (2.65lbs) |
Transmitter
| Output power* |
|---|
| HI |
| MID |
| LOW |
| Modulation |
| Spurious radiation |
| Maximum frequency deviation |
| Audio distortion (at 60% modulation) |
| Microphone impedance |
50W Approx. 10 W Approx. 5W Reactance modulation Less than -60dB ±5kHz Less than 3% (300 to 3000Hz) 500 to 600Ω
Circuitry Double conversion superheterodyne Intermediate frequency (1st/2nd) 10.7MHz/455kHz Sensitivity (12dB SINAD) Less than 0.16µV Selectivity -6dB -60dB More than 12kHz Squelch sensitivity Less than 0.1µV Output (5% distortion) More than 2W across 8Ω loads External speaker impedance 8Ω
Notes ;
Receiver
1. Circuit and ratings are subject to change without notice due to advancements in technology.
2. * Recommended duty cycle : 1 minute Transmit, 3 minutes Reception.
KENWOOD CORPORATION
Shionogi Shibuya Building, 17-5, 2-chome Shibuya, Shibuya-ku, Tokyo 150, Japan
KENWOOD U.S.A. CORPORATION COMMUNICATIONS & TEST EQUIPMENT GROUP P.O. BOX 22745, 2201 East Dominguez St., Long Beach, CA 90801-5745, U.S.A. KENWOOD ELECTRONICS DEUTSCHLAND GMBH Rembrücker Str. 15, 6056 Heusenstamm, West Germany KENWOOD ELECTRONICS BENELUX N.V. Mechelsesteenweg 418 B-1930 Zaventern, Belgium TRIO-KENWOOD FRANCE S.A. 13, Boulevard Ney, 75018 Paris, France KENWOOD ELECTRONICS AUSTRALIA PTY. LTD. P.O. Box 504, 8 Figtree Drive, Australia Centre, Homebush, N.S.W. 2140, Australia KENWOOD & LEE ELECTRONICS, LTD. Wang Kee Building, 5th Floor, 34-37, Connaught Road, Central, Hong Kong KENWOOD ELECTRONICS CANADA INC. P.O. BOX 1075, 959 Gana Court, Mississauga, Ontario, Canada L4T 4C2
Extending TM-241 frequency ranges
There are two methods of reconfiguring the TM-241. One is to cut a jumper wire ; the other is to replace chip diodes. (If both methods are used, cutting the jumper wire has priority.)
-
1. Cutting a jumper wire
- Turn the power off, remove the top of the radio, and cut the green wire on the left of the front panel. Tape the wire so that it cannot cantact other parts.
2 ) Frequency ranges after extension
Destination
| к, | Ρ | TX | : | 142,000 | ~ | 151,995 | MHz | |||
|---|---|---|---|---|---|---|---|---|---|---|
| Е | RX/TX | 136,000 | ~ | 173,995 | MHz | |||||
| М | RX | : | 118,000 | ~ | 173,995 | MHz | ( | FM | ) | |
| TX | : | 136,000 | ~ | 135,995 | MHz |
1/6
2. Replacing chip dioses
Frequencing can be changed by replacing the diodes for the destination set bits ( a0 - a4 ) as shown below.
|
Destination set bit
a4a3a2a1a0 |
Transmit frequency | Receive frequency Initial | Initial | Initial | autr | STEP ( @: Initial value ) | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Destination - | MIN | MAX | MIN | MAX | value | AS | SHIFT | 5 | 10 | 15 | 20 | 12.5 | 25 | |
| 00010 | E1 | 144 | 146 | 144 | 146 | 144 | ± 0.5 | 0 | 0 | 0 | 0 | ٢ | 0 | |
| 00011 | C1 | 136 | 174 | 136 | 174 | 144 | ± 5.7 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 01000 | E3 | 144 | 146 | 136 | 174 | 144 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 01010 | E2 | 136 | 174 | 136 | 174 | 144 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 10010 | M2 | 136 | 174 | 136 | 174 | 144 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 10110 | M1 | 144 | 148 | 144 | 148 | 144 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 10111 | К1 | 144 | 148 | 118 | 174 | 144 | 0 | ± 0.6 | ۲ | 0 | 0 | 0 | 0 | C |
| 11110 | КЗ | 136 | 174 | 118 | 174 | 144 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | 0 | |
| 11111 | K2 | 142 | 152 | 118 | 174 | 144 | 0 | ± 0.6 | 0 | 0 | 0 | 0 | 0 | ţ. |
0: With diode 1: Without diode
2 ) Changing parts
Printed circuit of X57-3690-00 ( CONT B/2 ) unit
Pattern cut when reconfiguring DRS transmission
| Bit | a4 | a3 | a2 | al | a0 |
|---|---|---|---|---|---|
| Ref. | D210 | D206 | D207 | D208 | D209 |
| Part name | MA141A | 1SS184 | 1SS184 | 1SS184 | MA141A |
2/6
Loading...