Box contents
Unpack your Here2Anywhere carefully and make
sure that everything listed here is present:
1 x Here
2
Anywhere
main unit
1 x Remote control 2 x AAA batteries
If anything is missing or damaged, or if your
Here
2
Anywhere fails to operate, notify your dealer
immediately. If your Here
2
Anywhere was shipped to
you directly, notify your shipper immediately.
Kenwood recommends that you retain the original
carton and packing materials in case you need to
ship your Here
2
Anywhere in the future.
Safety precautions
Warning
Take the following precautions to prevent traffic
accidents and avoid personal injury:
• Installation must be performed according to this
installation manual. Kenwood is not responsible
for issues arising from installations not performed
according to the procedures in this manual.
• Do not install the unit where it may obstruct your
view through the windshield or of your vehicle’s
indicator displays.
• Do not install the unit where it may hinder the
function of safety devices such as an airbag.
Doing so may prevent the airbag from functioning
properly in the event of an accident.
• The installation and use suggestions contained in
this manual are subject to any restrictions or limitations that may be imposed by applicable law—
the purchaser should check applicable law for any
restrictions or limitations before installing and/or
operating this unit.
• Failure to follow these safety instructions and
warnings may result in a serious accident.
CONGRATULATIONS!
Your Here2Anywhere™ Portable SIRIUS®Satellite Tuner lets you enjoy SIRIUS Satellite’s digital entertainment streams anywhere you’ve installed one of our KPA-H2H Home Docking Kits or KPA-H2C/KPA-H2CFM
Car Docking Kits (available separately). Use this manual to familiarize yourself with all of Here
2
Anywhere’s
features and capabilities.
For the latest information about this and other Kenwood products, visit the
Kenwood USA Corporation Web site at: www.kenwoodusa.com
Here2Anywhere Instruction Manual (ver. 2)Here
2
Anywhere Instruction Manual (ver. 2)
2 3
SEL
DISP
MEMO
PRE
PWR
6
5
4
3
2
1
Table of contents
Congratulations.....................................................2
Box contents .........................................................3
Safety precautions ................................................3
Installation in a vehicle.........................................6
Mounting the antenna...........................................8
Installation in a home .........................................10
Finding a location for the antenna .....................11
Front panel controls and features ......................14
Remote control functions....................................15
Activating your SIRIUS subscription....................16
Removing Here
2
Anywhere from the dock ...........16
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . .17
Selecting music . . . . . . . . . . . . . . . . . . . . . . . . .18
Setting and using stream presets . . . . . . . . . . .20
Saving and recalling music information . . . . . . .22
Display options . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setup mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Troubleshooting guide . . . . . . . . . . . . . . . . . . . .34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .35
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
Note
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment may cause harmful interference to radio
communications if it is not installed and used in accordance with these instructions. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/T V
technician for help
Cleaning the unit
If the unit becomes dirty, turn its power off and wipe
it clean with a soft dry cloth.
Do not use hard cloths or paint thinner, alcohol, or
other volatile solvents to clean the unit. These may
cause damage or remove indicator characters.
Warning
Do not operate the unit in a way that might divert your
attention from driving safely. As a driver, you alone
are responsible for safely operating your vehicle in
accordance with traffic safety laws at all times.
Warning
Take the following precautions to prevent fire and
avoid personal injury:
• To avoid short circuits, never put or leave any
metallic objects (coins, tools, etc.) inside the unit.
• If the unit emits smoke or strange smells, turn the power
off immediately and consult your Kenwood dealer.
• Do not drop the unit or subject it to strong shocks.
• If the LCD display becomes damaged or broken,
do not touch the liquid crystal fluid. The fluid may
be dangerous to your health or even fatal. If the
liquid crystal fluid contacts your body or clothing,
immediately wash it off with soap and water.
Caution
Take the following precautions to keep the unit in
proper working order:
• Be sure the unit is connected to a 12V DC power
supply with a negative ground connection.
• Do not open the unit.
• Do not install the unit where it will be exposed to
high levels of humidity, moisture, or dust.
• When replacing a fuse, use only a new one with
the proper rating. Using a fuse with the wrong
rating may cause the unit to malfunction.
• To prevent a short circuit when replacing a fuse,
first disconnect the wiring harness.
• When drilling holes to mount the unit, make sure
not to damage wiring or other systems on the
other side.
Note
If the unit doesn’t seem to be working properly:
• Turn the unit’s power off, wait 5 – 10 seconds,
then turn the power on again.
• If the unit still mis-operates, turn the unit’s power
off, remove it from the cradle, wait 5 – 10 seconds,
replace it in the cradle and turn the power back on.
If the problem persists, consult your Kenwood dealer.
FCC Warning
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in this
Here2Anywhere Instruction Manual (ver. 2)Here
2
Anywhere Instruction Manual (ver. 2)
4 5
Here2Anywhere Instruction Manual (ver. 2)
7
Here2Anywhere Instruction Manual (ver. 2)
6
Installation in a vehicle (continued)
Installation in a vehicle with the KPA-H2C kit (available separately)
Note: Do not put Here2Anywhere in the docking station until you have completed the installation.
2. You can bend the leaves on the base to
conform to curved mounting surfaces.
3. Peel the covering away from the adhesive on
the bottom of the base and adhere it to the
mounting surface. Use the provided screws
to securely attach the base to the surface.
• If using screws, be sure that you do not
damage wiring or other systems on the
other side of the mounting surface.
1. Determine where you want to mount
Here2Anywhere.
• Do not install Here2Anywhere where
it may obstruct your view through
the windshield or your view of your
vehicle’s indicator displays.
• Do not install Here2Anywhere where
it will hinder your access to the
vehicle’s controls.
• Do not install Here2Anywhere where
it may hinder the function of safety
devices such as an airbag. Doing so
may prevent the air-bag from
functioning properly in the event of
an accident.
• Find a location that provides good
visibility of and access to
Here2Anywhere’s front panel.
• Kenwood strongly recommends that
you mount Here2Anywhere in a
location where the base can be
attached with the provided screws.
5A. Plug the cassette adapter into the back of the cradle, as shown on the left.
5B. If your car stereo has an aux input, plug the supplied audio cable (instead of the
cassette adapter) into the back of the cradle, as shown on the right. Plug the audio
cable’s white (L ch,) and red (R ch.) connectors into your car stereo.
4. Plug the cigarette lighter adapter
into the back of the cradle, as shown.
Don’t plug the adapter into the
cigarette lighter until the installation
is completed (see pg. 10, Step 10).
6. Temporarily plug the antenna into
the “1-Sat/Terr (Main)” connector on
the back of the cradle until it is firmly
seated, as shown.
2. Before permanently mounting the antenna and routing the
cable, confirm that the antenna is mounted in a good location:
a. Temporarily plug the cigarette lighter adapter into the
cigarette lighter.
b. Slide Here2Anywhere all the way into the cradle so that the
connector at the rear of the unit makes proper contact in the
cradle. Press the POWER button to turn Here2Anywhere on.
c. If your Here2Anywhere has been properly connected and the
antenna is receiving the SIRIUS signal (preview stream
#184) you will hear audio. If you do not hear audio, the
display will read “Acquiring Signal”. Re-orient the antenna
until you hear audio. (See
Antenna Signal
, on page 33 to use
the ANTENNA SIGNAL screen to aim the antenna.)
• Make sure the vehicle is not in garage, or somewhere the
satellite signal could be blocked
3. Turn Here2Anywhere’s power off and remove it from the
cradle; unplug the cigarette lighter adapter from the cigarette
lighter; unplug the antenna from the cradle.
4. Remove the yellow protective backing from the adhesive strip
and firmly adhere it to the underside of the antenna tail. (Do
not remove the red protective backing at this time.)
5. Once the strip is adhered to the tail, remove the red protective
backing from the adhesive and firmly adhere the tail to the
vehicle.
• At room temperature, maximum adhesion usually occurs
within 72 hours. During this period, car washes and other
contact with the antenna and tail should be avoided.
6. Route the exposed portion of the antenna cable from the end
of the tail to the vehicle’s interior by tucking it underneath the
rubber molding around the vehicle’s rear window, as shown
below.
Here2Anywhere Instruction Manual (ver. 2)
9
Installation in a vehicle (continued)
Here2Anywhere Instruction Manual (ver. 2)
8
Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic housings from the antenna connectors
before connecting it to the cradle—we recommend labeling the wires with their respective colors. (See pg. 9, figure 16 of the CX-SR10
Installation Manual for details). Once you’ve removed the housings, connect the wire that had the yellow connector to the connector
on the cradle labeled “1-Sat/Terr (Main)”, and connect the other one to the connector labeled “2-Terr”.
Mounting the included
antenna
1. Find an antenna location on a metal
surface at least 12” x 12”. The antenna
should be mounted exactly 5.5” (the length
of the antenna’s tail) away from the vehicle’s
rear window, so that only the portion of the
cable protected by the tail is exposed, as
shown to the right. The antenna’s 3 powerful
magnets will secure it to the metal surface.
• Do not shorten the antenna’s tail. Doing
so could damage the cable, since its
insulation is integrated with the tail.
• Best reception is achieved with the antenna mounted on the roof; mounting on the
trunk lid will work for convertibles. If the
vehicle has a roof rack or skid ribs, it may
be necessary to mount the antenna offcenter.
Finding a location for the
antenna
Installation in a home with the
KPA-H2H kit (available separately)
Note: Do not put Here2Anywhere in the docking
station until you have completed the installation.
Installation in a home with the KPA-H2H kit
(continued)
11
Mounting the antenna (continued)
Here2Anywhere Instruction Manual (ver. 2)
10
2. Plug the AC cord into the power
supply, then plug the power supply
into the back of the cradle, as shown.
Don’t plug the AC cord into a wall outlet until the installation is completed.
1A. Plug the audio cable’s mini connector into the back of the
cradle, as shown.
1B. Plug the audio cable’s white
(L ch,) and red (R ch.) connectors into your audio system.
7. Route the cable from the lowest point of the rear window
into the trunk. Take advantage of any existing cable
channels or wiring conduits.
• For SUVs, minivans & 5-door vehicles, bring the cable into
the vehicle under the rubber molding for the tailgate, and
continue under the interior trim.
8. From the trunk, route the cable around the passenger compartment and to the back of the cradle.
• Do not pull the cable across sharp edges that could damage it.
• Keep the cable away from areas where it could become
tangled in driver’s and passenger’s feet.
9. Plug the antenna into the back of the cradle (see pg. 7,
Step 6).
10. Plug the cigarette lighter adapter into the cigarette lighter.
• KENWOOD RECOMMENDS UNPLUGGING THE CIGARETTE LIGHTER ADAPTER AFTER YOU TURN THE VEHICLE’S IGNITION OFF. (In some vehicles, the cigarette
lighter remains active after the ignition has been turned
off, and leaving Here
2
Anywhere’s cigarette lighter
adapter plugged-into the cigarette lighter could drain
the vehicle’s battery.)
3. Plug the antenna into the back
of the cradle until it is firmly
seated, as shown.
Here2Anywhere Instruction Manual (ver. 2)
4. Due to the paths of the SIRIUS satellites
over the US, the best location for the
antenna will depend on what part of the
country you live in, the orientation of
your home, and the locations of any
obstructions that could prevent the satellite signal from reaching the antenna.
The best antenna location is on the roof,
facing straight up (
see below
).
• The location of the “X” on the map on page
13 must be visible to the antenna
Note:
The antenna is
weatherproof, so it can
be mounted outside
Finding a location for the antenna (continued)
Use this map as a general placement guideline—some experimentation may be needed to obtain the best reception in your particular situation. See pg. 33,
Antenna Signal
, for more information about using the ANTENNA SIGNAL screen to aim the antenna.
13
Here2Anywhere Instruction Manual (ver. 2)
If you live in:
Section 1 —
Use a
NORTHEAST or EAST-
FACING
wall or window
Section 2 —
Use a
NORTHEAST or NORTH-
FACING
wall or window
Section 3 —
Use a
NORTHWEST or NORTH-
FACING
wall or window
Section 4 —
Use a
NORTHWEST or WEST-
FACING
wall or window
Section 5 —
Place the antenna
ONLY ON THE
ROOF or ON AN OUTSIDE WALL
Finding a location for the antenna (continued)
Here2Anywhere Instruction Manual (ver. 2)
12
The second best antenna location is on an outside wall
• Use an appropriate wall, depending on where you live (refer to
the map on page 13). The location of the “X” on the map must
be visible to the antenna
• Mount the antenna facing as close to straight up as
possible (
below, left
)
• To minimize interference caused by roof extensions, mount
the antenna as low on the wall as possible while avoiding
other obstructions (
below, right
).
The third best antenna location is at a window
• Use an appropriate window, depending on where you live
(refer to the map on page 13). The location of the “X” on the
map must be visible to the antenna
• Place the antenna midway between the left and right window
frames
• Tilt the hinged part of the
antenna back to aim it
towards the sky (
right
)
Note: Objects such as the
following can prevent the
antenna from receiving the
satellite signal when placed
at a window or on an outside
wall: • roof extensions •the
window frame •metallic
window screens or tinting
•objects in the window
•nearby objects like trees,
foliage or buildings
If the signal is blocked from
getting to the antenna, the
antenna must be relocated
to a more appropriate
window, an outside wall free of obstructions, or on the roof.
Note:
The antenna is
weatherproof,
so it can be
mounted
outside
Remote control functions
15
Front-panel controls and features
Here2Anywhere Instruction Manual (ver. 2)
14
Here2Anywhere Instruction Manual (ver. 2)
Installing Batteries in
the Remote
1. Remove the battery cover
as shown on the left
2. Install two AAA batteries
as shown on the right
3. Replace the battery cover
POWER Butt on:
Turns Here2Anywhere on and off; exits menu screens
Up/Down/Left/Right AArrow BButto ns:
Navigate through display screens
SELECT Button:
Press to select items highlighted on the display; hold-down to
jump to the previously-received Stream
SETUP Butt on:
Enters and exits the Setup Mode
DISPLAY Button:
Switches the display between different modes
MEMORY Button:
Saves & recalls song & artist information; sets Parental Lock
code number
Numbe r BB uttons :
Selects streams directly and by preset
DIRECT But ton:
Accesses streams directly by number
PRESET Button:
Accesses the 4 banks of presets; enters & exits the Preset Tune Mode
U p/ Do w n/ L ef t/ R ig h t
Arrow BButtons :
Navigates
through display screens
Displ ay:
Shows information about streams, categories, artists, songs and
setup information
Remote CControl RReceiver :
Receives signals from
the included wireless
remote control
POW ER But ton:
Turns
Here
2
Anywhere on and
off; enters & exits the
Setup Mode, and exits
the Stream, Category,
Song & Artist List modes
SELECT Button :
Makes selections of items highlighted
on the display
Prese t NNumbe r BBut tons:
Sets and selects preset
streams
PRES ET Butt on:
Cycles-through the 4 banks of
presets; enters & exits the Preset Tune Mode
MEMORY Bu tton:
Saves & recalls song & artist
information; sets Parental Lock code number
DISP LAY B utton:
Switches the display between
different modes
1716
Basic operation
After you have activated your SIRIUS
subscription, the Normal Operation screen will
appear (top right):
Use the up & down arrow buttons to select
streams
• The selected stream will automatically play
The name and artist of the currently-playing song
will scroll across the display
If you want to listen to a different entertainment
category, press the left & right arrow buttons to
activate the Category Select screen (bottom right):
1. Use the left & right arrow buttons to select
entertainment categories
2. When the category you want is highlighted,
use the up & down arrow buttons to highlight
the stream you want to hear
3. When the stream you want is highlighted,
press the SELECT button to listen to the
stream. The display will revert to the Normal
Operation screen for that stream.
Here2Anywhere Instruction Manual (ver. 2)
Normal Operation Screen
Category Select Screen
Activating your SIRIUS subscription
Before you can listen to Here2Anywhere, you must
subscribe to SIRIUS Satellite’s service.
1. Make sure that Here
2
Anywhere is properly
connected and that its antenna is oriented to
receive the SIRIUS satellite signal (see
Installation sections for details).
2. Place Here2Anywhere in the docking station
by sliding the unit all the way into the cradle so
that the connector at the rear of the unit makes
proper contact in the cradle.
3. Press the power button to turn Here2Anywhere on.
After displaying the Kenwood and SIRIUS logos, the
display will read “Acquiring Signal”. Once the SIRIUS
satellite signal is received, the display will change to
“Call 1-888-539-SIRIUS to Subscribe”.
4. If your Here2Anywhere has been properly
connected and the antenna is receiving the
SIRIUS signal (preview stream #184) you will
hear audio. If you do not hear audio, re-orient the
antenna until you do. (See Antenna Signal, on
page 33 to use the ANTENNA SIGNAL screen.)
• Stream # 184 is the SIRIUS preview stream. You
will not be able to tune to any other streams
until you activate your SIRIUS subscription.
5. Hold the POWER button on the front panel for at
least 1 second or press the SETUP button on the
remote to enter the Setup Mode.
6. Your unit’s unique 12-digit SIRIUS ID Number will
be displayed
(right). Write the
number down
and have your
credit card
handy.
7. Contact SIRIUS on the Internet at:
www.siriusradio.com. Click on the “Activate Your
Subscription” link.
• You can also call SIRIUS toll-free at 1-888-539SIRIUS (7474). The operator will instruct you.
8. Once your subscription has been activated, the
display will read “Subscription Updated: Press
any key to continue”, then will revert to the
Normal Operation screen (see next page).
Removing Here2Anywhere from the dock
To remove Here2Anywhere from the docking station,
press the button on the underside of the unit and
gently slide Here
2
Anywhere out of the cradle.
Here2Anywhere Instruction Manual (ver. 2)
19
4. If you decide not to select another stream, press the POWER button on the front panel to exit the mode.
The display will revert to the Normal Operation screen for the active stream.
• You can switch to the previously-selected stream by holding the SELECT button for at least 1 second.
Holding the SELECT button for 1 second again switches back to the original stream.
• If no streams are available in a category, or if all of the streams are set to be skipped or locked, the display
will read “No Channels Available” when that category is highlighted. (See Channel Skip/Lock on pg 29.)
Selecting music
In addition to the Normal Operation and Category Select screens, Here2Anywhere has three ways to search
for and select music: by stream, by artist, and by song.
Selecting music by stream (Stream List Mode)
1. Press the Select button while in the Normal
Operation mode. The Stream List screen will
appear, showing all available streams regardless of
category (right):
2. Use the up & down arrow buttons to move through
the streams.
3. When the stream you want is highlighted, press the
SELECT button to play the stream. The display will
automatically return to the Normal Operation screen.
Here2Anywhere Instruction Manual (ver. 2)
18
Here2Anywhere Instruction Manual (ver. 2)
Selecting music by artist (Artist List Mode)
1. While the Normal Operation screen is active, press the
SELECT button once, then the DISPLAY button once.
The Artist List screen will appear, showing all currently-playing artists regardless of category (top, right):
• If composer information is available for a stream, it
will be displayed along with the artist information
2. Use the up & down arrow buttons to move through
the list of artists
3. When the artist you want to hear is highlighted, press the SELECT button to listen to them
• After you make your selection, the display will revert to the Normal Operation screen
Selecting music by song (Song List Mode)
1. While the Normal Operation screen is active, press the
SELECT button once, then the DISPLAY button twice.
The Song List screen will appear, showing all currentlyplaying songs regardless of category (bottom, right):
• Song titles too long to fit on the highlight bar will
scroll
2. Use the up & down arrow buttons to move through
the list of songs
3. When the song you want to hear is highlighted, press the SELECT button to listen to it
Artist List Screen
Song List Screen
Stream List Screen
Here2Anywhere Instruction Manual (ver. 2)
21
• After you make your selection, the display will revert to the Normal Operation screen
Note: In the Stream List, Artist List and Song List modes, if you don’t want to make a selection, press the POWER
button on the front panel to exit the mode and return to the Normal Operation screen for the active stream.
Setting/using stream presets
Setting stream presets
You can store up to 24 of your favorite streams as presets, for
quick access. Presets are stored in 4 banks, each containing
6 stream presets.
1. Press the PRE (Preset) button to activate the preset bank
you want. The selected bank is shown in the lower left
corner of the Normal Operation Screen (right).
2. Select the stream you want to preset (see Basic Operation and Selecting Music, pg. 17–18)
3. Hold the number button you want to store the stream in for at least 2 seconds
• The selected preset number will flash and then remain lit on the display to show that it has been memorized.
• If the preset button already has a stream stored in it, it will be replaced with the new stream
Tuning stream presets
The 6 presets in the active bank can be selected by pressing the “1” – “6” buttons
1. Press the PRE button to cycle through the four banks of preset stations. The display will show the
current preset bank and active preset number in the lower left corner.
Here2Anywhere Instruction Manual (ver. 2)
20
2. When the desired preset bank is displayed, use the “1” – “6” buttons to tune the desired preset stream
Searching for a stream preset (Preset List Screen)
There are two ways you can search for a stream preset.
For both, hold the PRE button for at least 1 second to
enter the Preset Tune mode. The Normal Operation
Screen will change so that the preset bank and
preset number will be highlighted (top, right).
Option 1: Use the up & down arrow buttons to move
through the presets. Each time you change a
preset its number will appear on the display
and the stream will play.
Option 2: Press the SELECT button. The Preset List
Screen will appear on the display, listing all
of the stream presets that have been programmed (bottom, right)
• Use the cursor up & down buttons to scroll
through the list. Press the SELECT button
when the desired stream is highlighted on
the display to select it.
In either mode, when you’re finished searching for a
preset, press the POWER button to exit and return to the Normal Operation Screen.
Preset List Screen
Preset Tune Screen
Normal Operation Screen, showing
Preset Bank and Preset Number
Readout
2322
the list of saved songs until the one you want is highlighted.
3. Press and release the SELECT button. An “S” will appear next to the song’s name (see bottom of previous page).
4. When one (or more) of the selected songs is playing on any stream, the following will happen:
a. A ‘beep’ will sound, aler ting you that a selected
song is playing. (To disable the ‘beep’, see page 32.)
b. An alert screen will be superimposed over the data
on the original screen (right).
• The number on the screen will count down from
‘10’ to ‘0’.
c. To hear the song, press the SELECT button before
the counter reaches zero and Here
2
Anywhere will
switch to the stream that is playing the song.
d. To make the alert screen disappear without
listening to the song, press the POWER button on
the front panel.
• If you do nothing, the alert screen will disappear
when the counter reaches zero.
Display options
Changing display modes
The Normal Operation Screen has two display modes,
Normal and Large Font (right).
Here2Anywhere Instruction Manual (ver. 2)
Song Seek Alert Screen
Saving/recalling music information
Saving music information
You can store the name of the currently-playing song
and artist (and composer, if the data is available) into
memory for recall later.
Press the MEM button to save the data. The screen will display the following message (above):
• If the song has already been stored in memory, the
display will read “Already Stored”.
• You can save data for up to 24 songs. Once all 24
places have been filled, any new artist/song data you
save will replace the oldest data.
Recalling music information
1. Hold the MEM button for more than 1 second. The Song Memory List screen will appear (above):
2. Use the up & down arrow buttons to scroll through the list
Activating Song Seek
You can have Here2Anywhere automatically prompt you
when any of the songs saved on the Song Memory List
is playing on any stream.
1. Activate the Song Memory List screen (see above).
2. Use the up & down arrow buttons to scroll through
Here2Anywhere Instruction Manual (ver. 2)
Song Memory List Screen
Song Seek Icon
Normal Operation Screen
Large Font Screen
Clock Setup
Here2Anywhere has an automatic clock that receives its
time signal as part of the SIRIUS satellite stream.
To set the clock, you need to tell Here
2
Anywhere what
time zone you live in and if your local area observes
Daylight Savings Time.
1. While in the Setup Mode, press the left or right arrow
buttons until the Auto Clock Setup screen appears
(top, right).
2. Press the up or down button once and the Time Zone
Setup screen appears (middle, right).
3. Press the up or down arrow buttons until your time
zone is highlighted, then press the SELECT button.
• The screen will change to the Daylight Savings screen (bottom, right).
3. If your local area observes Daylight Savings Time, press the SELECT button so an “X” appears in the box
on the display’s fourth line; if your local area does
not observe Daylight Savings Time, press the SELECT
button so that the box is empty.
Note: If you drive into another time zone (or into an
area with a different Daylight Savings Time status than
your local area) you will have to re-set the clock.
25
24
Here2Anywhere Instruction Manual (ver. 2)
Time Zone Setup Screen
Daylight Savings Screen
Press the DISPLAY button to cycle the display between the two modes.
Adjusting the display brightness
Hold the DISPLAY button down for over 1 second to
enter the Display Brightness mode (right):
1. Use the up & down arrow buttons to select the
desired brightness level (high/medium/low)
2. Press the SELECT button to save your selection
• Press the DISPLAY button to exit this mode
Setup Mode
The Setup Mode lets you access and set up the following features: SID (SIRIUS ID Number), Auto Clock
Setup, Alarm Clock Setup, Channel Skip/Lock, Lock Code Setup, Auto Shutoff Setup, Startup Mode, Output
Level, Text Flow Type, Audible Alert, and Antenna Signal.
To enter the Setup Mode, hold the POWER button on the front panel for at least 1 second. Use the left &
right arrow buttons to move to the setup feature you want, and press the SELECT button to select the
feature. To exit the Setup Mode and return to the previous operation mode, press the POWER button at any
time while the Setup Mode is active.
SID
When you first enter the Setup Mode, the unit’s unique
12-digit SIRIUS ID Number will be displayed (right):
Here2Anywhere Instruction Manual (ver. 2)
Display Brightness Screen
SIRIUS ID Screen
Auto Clock Setup Screen
7. Use the up and down arrow buttons to move through the streams until the one you want is highlighted.
8. Press the SELECT button to save your setting. The Alarm Setup screen will reappear.
Press the POWER button on the front panel to exit the Setup Mode.
Using the alarm
At the specified time (see above) , Here
2
Anywhere will automatically turn itself on to the selected stream.
• The stream number will flash positive and negative.
Note: To hearHere
2
Anywhere, make sure that the audio system it is connected to is turned on.
To enter the “Snooze” mode, press any button once.
• The Snooze cycle is 10 minutes long.
• You can repeat the Snooze cycle as many times as you want.
To shut the alarm off, press any button twice. (This shuts Here
2
Anywhere completely off.)
To listen to Here
2
Anywhere after you’ve shut the alarm off, press the POWER button.
Important: If you remove Here
2
Anywhere from the dock and replace it in the same (or another) dock, you must
power it up at least once for it to re-acquire the clock stream data before the alarm function will work. (You don’t
have to re-set the alarm.) Once you have powered Here
2
Anywhere up once you can turn it off and the alarm will
function properly. As long as Here
2
Anywhere remains in the cradle after being powered-up it will retain the clock
stream and the alarm will function properly.
Auto Shutoff
You can set Here2Anywhere to automatically shut off if it is accidentally left on (if a button isn’t pressed for
Timer Functions
Here2Anywhere has three Timer functions. The Alarm turns Here2Anywhere on at a specified time and to a
specified stream, Auto Shut-Off automatically turns it off at a specified time, and the Sleep Timer lets you
listen to Here
2
Anywhere for a specified period of time
before it automatically shuts off.
Setting the Alarm
1. While in the Setup Mode, press the left or right arrow
button until the Alarm Setup screen appears (top right).
2. Press either the up or down button. The Step 1 — Set
Alarm Time screen appears (middle, right).
3. Use the up and down arrow buttons to set the hour
you want Here
2
Anywhere to turn on. (The alarm will
automatically switch from AM to PM.)
4. When the display shows the correct hour, press the
right arrow button to highlight the minutes. Use the
up and down arrow buttons to set the minute you
want Here
2
Anywhere to turn on.
5. When the display shows the correct hour and minute,
press the SELECT button to turn the alarm on.
6. Press the MEM button to save your settings. The
Step 2—Set Channel screen will appear (bottom, right).
27
26
Here2Anywhere Instruction Manual (ver. 2)Here2Anywhere Instruction Manual (ver. 2)
Alarm Setup Screen
Step 1—Set Alarm Time Screen
Step 2—Set Stream Screen
amount of time you want Here2Anywhere to play before it shuts off.
4. Press the SELECT button to confirm your selection and activate the Sleep Timer.
When the Sleep Timer is active, the display will return to the Normal Operation screen.
• The display will appear as normal except that every three seconds the timer countdown will replace the
stream number. You can still change streams and display modes as normal without shutting the timer off.
To cancel the Sleep Timer, turn Here
2
Anywhere’s power off, then turn it back on again.
Channel Skip/Lock
This allows you to select streams that you want to skip when scanning up and down the Channel List and
Category List screens, or simply when you’re pressing the cursor up & down buttons.
1. While in the Setup Mode, press the left or right arrow
button until the Channel Skip screen appears (right).
2. Use the up & down arrow buttons to highlight the
stream you want. (The highlighted stream will
automatically play.)
3. Press the SELECT button to change the highlighted
stream’s status from “available” (+) to “skip” (–).
• To exit the Channel Skip function, press the left or right arrow button. The screen will display the next
Setup Menu item.
You can further lock a stream by placing it in the Channel Lock mode. Locked streams will be unavailable
during all tuning modes, and cannot be directly accessed via the remote control.
Here2Anywhere Instruction Manual (ver. 2)
29
15, 30 or 60 minutes). This is especially useful if your vehicle’s cigarette lighter remains powered after the
ignition has been turned off.
1. While in the Setup Mode, press the left or right arrow button until the Auto Shutoff Setup screen appears (below).
2. Press the up or down arrow buttons until the display
shows amount of time you want Here
2
Anywhere to
stay on after the last time a button is pressed before
it automatically shuts off.
• When Auto Shutoff is activated, a ‘beep’ will sound and
the screen will display a countdown warning 10 seconds before Here
2
Anywhere shuts itself off. Pressing
any button during this countdown will cancel the Auto Shutoff process and restore normal operation.
3. Press the POWER button to exit.
Sleep Timer
You can program Here2Anywhere to play for 30 or 60 minutes and then automatically turn itself off.
Note: You must re-set the Sleep Timer each time you want to use it.
1. While listening to SIRIUS, press the SELECT button to
enter the Stream List mode (see page 18).
2. Hold the left arrow button for at least 1 second. The
Timer Setup screen will appear (right).
3. Press the left or right arrow button to highlight the
Here2Anywhere Instruction Manual (ver. 2)
28
Timer Setup Screen
Channel Skip Screen
Auto Shutoff Setup Screen
reappears. Repeat Steps 3 – 4.
5. Using the preset 1 – 6 buttons, enter your new 4-digit
code. The screen’s second line will change from
“_ _ _ _” to “* * * *”.
6. Press the MEMORY button. The Confirm Number
screen appears (right).
7. Re-enter your new 4-digit code. The screen’s second
line will change from “_ _ _ _” to “* * * *”.
8. Press the MEMORY button. The display will change to “New Code Confirmed”
• If you entered the code incorrectly, “Code Error” will be displayed, and the Enter New Lock Code screen
reappears. Repeat Steps 5 – 8.
Startup Mode
You can select which screen is displayed when you turn Here2Anywhere’s power on.
1. While in the Setup Mode, press the left or right arrow
button until the Startup Mode screen appears (right):
2. Use the up & down arrow buttons to highlight
the screen you want for Startup: Normal Operation,
Channel List (Stream List) or Category List
(see pages 17 – 18):
3. Press the SELECT button.
Here2Anywhere Instruction Manual (ver. 2)
31
To lock a stream, in Step 3 above, instead of momentarily pressing the SELECT button, hold the button for
more than 1 second. A “–” and a padlock will be displayed next to the stream number.
Lock Code Setup
If you have locked any streams in the Channel Lock
mode, you will need to enter a 4-digit lock code to
unlock them. The factory default lock code is “1 1 1 1”.
You can change the Lock Code to your own preference:
1. While in the Setup Mode, press the left or right arrow button until the Lock Code Setup screen appears (top right):
2. Press the up or down arrow button. The Lock Code
screen appears (middle, right):
3. Using the preset 1 – 6 buttons, enter the factory
default code “1 1 1 1”. The screen’s second line will
change from “_ _ _ _” to “* * * *”.
• If you enter an incorrect number, use the left arrow
button to delete the incorrect number; then
re-enter the correct one.
4. Press the Memory button. The Enter New Lock Code
screen appears (bottom, right).
• If you entered the code incorrectly, “Code Error” will
be displayed, and the Enter New Lock Code screen
Here2Anywhere Instruction Manual (ver. 2)
30
Lock Code Screen
Enter New Lock Code Screen
Confirm Number Screen
Startup Mode Screen
Lock Code Setup Screen
1. While in the Setup Mode, press the left or right arrow
button until the Audible Alert screen appears (right):
2. Use the up & down arrow buttons to turn the audible
alert ‘beep’ on or off.
Antenna Signal
This screen shows the quality of the SIRIUS satellite
signal that’s being received, to help you find the best location for the antenna.
1. While in the Setup Mode, press the left or right arrow
button until the Antenna Signal screen appears (right):
• After a few seconds the signal quality bars will indi-
cate how well the antenna is receiving the
SIRIUS satellite signal.
2. Find a location for the antenna that illuminates the
maximum number of bars.
• After moving the antenna, wait at least 2 seconds before moving it again, to enable the unit to process
the signal.
3. Due to the moving paths of the SIRIUS satellites, it is possible for the signal to change over time. In most cases,
signal should be available continuously, however, it may be temporarily blocked in some antenna locations in home
installations. Be sure to check the the Antenna Signal screen if there is a loss of signal or audio. Experimentation
with antenna placement in the home or outside may be necessary to ensure continuous reception.
• See pages 11–13 for information about properly locating the SIRIUS antenna in a home installation.
Here2Anywhere Instruction Manual (ver. 2)
33
Text Flow Type
You can set how the scrolling text flows across Here2Anywhere’s screen.
1. While in the Setup Mode, press the left or right arrow
button until the Text Flow Type screen appears (right):
2. Use the up & down arrow buttons to select the type
of text flow.
• In the DISCRETE mode the text moves across the
screen in steps
• In the CONTINUOUS mode the text moves across the screen smoothly.
Output Level
You can adjust Here2Anywhere’s output level so it matches other sources in your audio system.
1. While in the Setup Mode, press the left or right arrow
button until the Output Level screen appears (right):
2. Use the up & down arrow buttons to select the
desired output level.
• “High” is 0dB, “Medium” is –3dB and “Low” is –6dB.
Note: To avoid distortion with some cassette car stereos, you may have to lower the output level when using the cassette adapter.
Audible Alert
You can turn Here2Anywhere’s Song Seek and Auto Shutoff alert beep on or off (see pages 23 & 28).
Here2Anywhere Instruction Manual (ver. 2)
32
Antenna Signal Screen
Audible Alert Screen
Text Flow Type Screen
Output Level Screen
Troubleshooting guide (continued)
Here2Anywhere Instruction Manual (ver. 2)
35
Troubleshooting guide
Here2Anywhere Instruction Manual (ver. 2)
34
Problem Possible Cause Solution
No power on Here2Anywhere (power
indicator /display not illuminated)
Power supply/cigarette lighter
adapter not properly connected
Blown fuse in cigarette lighter
adapter
Make sure power supply/adapter
is properly connected
Check the fuse; if blown, replace
with supplied spare fuse
No sound
Audio cable/cassette adapter not
properly connected
Make sure cable/adapter is
properly connected
Display reads “Acquiring Signal”
Signal is weak or can’t be found
Metallic window screen is
interfering with reception
Check the Antenna Signal screen
(see page 33); Change the
antenna/vehicle location to
maximize signal quality
Move antenna to window with a
non-metallic screen
Display reads “Antenna Error”
The antenna is not connected
The antenna or cable is faulty
Verify antenna connections
Replace antenna
Display reads “Call 1-888-539-SIRIUS to
Subscribe”
SIRIUS subscription has not been
activated
Call SIRIUS to activate your
subscription
Display reads “Invalid Channel” Stream entered is invalid Select a different SIRIUS stream
Problem Possible Cause Solution
Here2Anywhere operates
erroneously
Microprocessor error
Turn the power off (press the
POWER button), wait 5 – 10
seconds, then turn the power on
again.
Turn the unit’s power off, remove
it from the dock, wait 5 – 10
seconds, replace it in the dock
and turn the power back on.
If the problem persists, consult
your Kenwood dealer.
Sound mutes intermittently
Metallic window screen is
interfering with reception
Move antenna to window with a
non-metallic screen
Specifications:
Audio output (100 ~ 250 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .950mV RMS
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3A fast blow
Power supply requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 ~ 16V, negative ground
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5”(W) x 45/16”(D) x 13/4”(H)
Loading...