before using your Kenwood
appliance
●
Read these instructions carefully
and retain for future reference.
●
Remove all packaging and any
labels.
safety
general
●
Never touch the mixing shaft whilst
the appliance is plugged in.
●
Keep fingers, hair, clothing and
utensils away from moving parts.
●
Always unplug:
●●
before fitting or removing parts
●●
after use.
●●
before cleaning
●
Never mix hot ingredients.
●
Never use a damaged appliance.
Get it checked or repaired: see
‘service’.
●
Never put the appliance in water or
let the cord or plug get wet - you
could get an electric shock.
●
Never let the cord touch hot
surfaces or hang down where a
child could grab it.
●
Never add ingredients to the beaker
whilst the appliance is operating.
●
Only use the appliance with the
beaker supplied.
●
Make sure the beaker is located
correctly before switching on the
appliance.
●
Do not let infirm people use the
appliance without supervision.
●
Do not let children use or play with
the appliance.
●
Only use the appliance for its intended
domestic use. Kenwood will not
accept any liability if the appliance is
subject to improper use, or failure to
comply with these instructions.
before plugging in
●
Make sure your electricity supply is
the same as the one shown on the
power handle.
important (UK) only
●
The wires in the cord are coloured
as follows:
Green and Yellow = Earth
Blue = Neutral
Brown = Live.
●
The appliance must be protected
by a 3A approved (BS1362) fuse.
●
WARNING: THIS APPLIANCE
MUST BE EARTHED.
Note:
●
For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct fuse cover is
identified by colour and a
replacement may be obtained from
your Kenwood Authorised Repairer
(see Service).
●
If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable pug is inadvertently
inserted into a 13A socket outlet.
●
This machine complies with
European Economic Community
Directive 89/336/EEC.
before using for the first time
1 Wash the parts: see ‘cleaning’.
key
control switch
beaker support/interlock
mixing shaft
beaker rest
beaker
maximum level
minimum level
tilting head
to use your drinks
maker
1 Make sure the control switch is off
(O) and then plug into the power
supply.
2 Place the ingredients into the
beaker.
●
The beaker must always be filled to
at least the minimum level mark
or the liquid will not reach the
mixing shaft. Do not fill above the
maximum level mark or liquid may
overflow while mixing.
3 Place the beaker onto the drinks
maker, making certain that the
beaker’s top edge is behind the
beaker support/interlock and its
bottom edge is on the beaker rest.
●
Failure to locate the beaker into the
beaker support/interlock will prevent
the appliance from operating.
●
To assist with the fitting or removal
of the beaker the drinks maker
head can be tilted upwards
.
Never tilt the head during the
mixing operation.
4 Move the control switch to the
desired speed. Start mixing on
speed 1 then increase to speed 2 if
required.
●
Most drinks should be mixed in less
than 2 minutes.
5 When mixing is complete, switch off
the drinks maker, remove the
beaker and pour out the drink.
hints on using your drinks
maker
●
Always place the liquid ingredients
into the beaker first.
●
Always mash fruit to a smooth
puree before adding to the beaker.
●
If using syrups and powdered mixes
add them just before mixing to
prevent them from sinking to the
bottom of the beaker.
●
For best results, all liquid
ingredients should be as cold as
possible. Milk drinks will taste better
if the milk is ice cold. The colder the
milk, the thicker and more frothy the
drink. Skimmed milk will produce a
frothier drink than semi-skimmed or
full fat milk.
●
Never try to mix frozen fruit with
your drinks mixer.
●
The drinks mixer will not crush ice.
For best results, use ready crushed
ice.
●
When blending large lumps of ice
cream, break them up first.
cleaning
●
Always switch off and unplug before
cleaning.
●
Never put the appliance in water or
let the cord or plug get wet.
beaker
Wash up, then dry. Or wash in your
dishwasher.
mixing shaft
1 Place 200ml warm, lightly soapy
water into the beaker. Attach the
beaker to the drinks maker and
operate on speed 1 for 20 - 30
seconds. When finished, switch off
and discard the liquid.
2 Repeat the above step using clean
warm water to rinse the mixer shaft.
3 Switch off and unplug the unit.
Wipe any residual soap and water
from the mixer shaft with a damp
cloth or sponge, then dry.
To clean the exterior of the drinks
maker, wipe with a damp cloth or
sponge. Dry thoroughly.