Kenwood NX-240, NX-340 Operation Manual

INSTRUCTION MANUAL

VHF DIGITAL TRANSCEIVER

NX-240

UHF DIGITAL TRANSCEIVER

NX-340

THANK YOU

We are grateful you have chosen KENWOOD for your land mobile radio applications.

NOTICES TO THE USER

Government law prohibits the operation of unlicensed radio

◆

transmitters within the territories under government control.

Illegal operation is punishable by ﬁ ne and/or imprisonment.

◆

Refer service to qualiﬁ ed technicians only.

◆

Safety: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.

The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,826,222, #5,754,974, #5,701,390, and #5,715,365.

Firmware Copyrights

The title to and ownership of copyrights for ﬁ rmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation.

PRECAUTIONS

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the transceiver and the battery pack.

• Do not use options not speciﬁ ed by KENWOOD.

• If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce the transceiver volume. Pay attention to the volume level when turning the squelch off.

• Do not place the microphone cable around your neck while near machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the radiator and chassis will become hot. Do not touch these locations when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional accessories.

• The charger is the device that disconnects the unit from the AC mains line. The AC plug should be readily accessible.

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inﬂ ammable gas, dust particles, metallic powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircraft. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the vehicle is running. When the airbag inﬂ ates, the transceiver may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your KENWOOD dealer.

• Use of the transceiver while you are driving may be against trafﬁ c laws. Please check and observe the vehicle regulations in your area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects, as they may short the battery terminals.

• When operating the transceiver in areas where the air is dry, it is easy to build up an electric charge (static electricity). When using an earphone accessory in such conditions, it is possible for the transceiver to send an electric shock through the earphone and to your ear. We recommend you use only a speaker/microphone in these conditions, to avoid electric shocks.

iii

Information concerning the battery pack:

The battery pack includes ﬂ ammable objects such as organic solvent. Mishandling may cause the battery to rupture producing ﬂ ames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in containers holding metal objects (such as wires, chain-necklaces or hairpins). If the battery pack is short-circuited, excessive current will ﬂ ow and the battery may generate heat or smoke, rupture, or burst into ﬂ ame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not leave the battery near ﬁ re, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not charge the battery near ﬁ re or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Use only the speciﬁ ed charger and observe charging

requirements!

If the battery is charged in unspeciﬁ ed conditions (under high

temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into ﬂ ame. If the battery’s protection circuit is damaged, the battery may charge at an abnormal current (or voltage), and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

ﬂ ame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current may ﬂ ow upon discharging. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating equipment, do not force it; check the polarity of the battery. If the battery pack is reverse-connected to the charger, it will be reversecharged and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems.

• Do not charge the battery for longer than the speciﬁ ed time!

If the battery pack has not ﬁ nished charging even after the

regulated time has passed, stop it. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

ﬂ ame.

• Keep ruptured and leaking battery packs away from ﬁ re!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from ﬂ ammable areas. Electrolyte leaking from battery can easily catch on ﬁ re and may cause the battery to generate smoke or burst into ﬂ ame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason, remove it from the charger or operating equipment and do not use it. The battery may generate heat or smoke, rupture, or burst into ﬂ ame.

CONTENTS

UNPACKING AND CHECKING EQUIPMENT .......................... 1

PREPARATION .......................................................... 2

ORIENTATION ........................................................... 7

PROGRAMMABLE AUXILIARY FUNCTIONS ........................ 8

BASIC OPERATIONS ..................................................11

VOICE OPERATED TRANSMISSION (VOX) .........................14

NXDN ................................................................... 15

BACKGROUND OPERATIONS ........................................ 16

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. If any of the items listed below are missing or damaged, ﬁ le a claim with the carrier immediately.

SUPPLIED ACCESSORIES

• Antenna ..................................................................................1

• Battery charger/ AC adapter (KSC-35S

• Li-ion Battery pack (KNB-45L

• Speaker/ microphone jack cover ............................................1

• Speaker/ microphone locking bracket .....................................1

• Belt clip (KBH-10) ................................................................... 1

• Screw (M3 x 8 mm) ................................................................2

• Channel stopper .....................................................................1

• Instruction manual ..................................................................1

Note:

◆ Refer to “PREPARATION” starting on page 2 for accessory installation instructions.

◆

Supplied with C6 type NX340.

) .............................................. 1

) ..............................1

PREPARATION

INSTALLING THE CHANNEL STOPPER

You can set the channel stopper position for channels 2, 4, 6, 8, 10, 12, and 14. Inserting the Channel stopper prevents unnecessarily selecting channels which do not exist.

• Selecting a channel which does not exist causes a continuous error tone to sound.

1 Set the Channel selector to channel 1, then pull the

Channel selector knob off the transceiver.

• If the Channel selector is not positioned at channel 1, the knob may

not install correctly and the channel may be unable to change.

2 Insert the channel stopper. 3 Set the arrow of the Channel stopper to the highest channel

number for the transceiver.

4 Reinsert the Channel selector knob.

Channel stopper

Arrow

INSTALLING THE ANTENNA

Antenna

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.

Note: The antenna is neither a handle, a key ring retainer, nor a speaker/ microphone attachment point. Using the antenna in these ways may damage the antenna and degrade your transceiver’s performance.

INSTALLING/ REMOVING THE BATTERY PACK

◆ Do not short the battery terminals or dispose of the battery by ﬁ re.

◆ Never attempt to remove the casing from the battery pack.

1 Align the battery pack with the back

of the transceiver, then press the battery pack and transceiver ﬁ rmly together until the release latch on the base of the transceiver locks.

2 To remove the battery pack, lift the

safety catch on the base of the transceiver, then press the release latch underneath the safety catch.

3 While pressing the release latch,

pull the battery pack away from the transceiver.

INSTALLING THE BELT CLIP

If necessary, attach the belt clip using the two supplied M3 x 8 mm screws.

Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment.

Belt clip

Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in these glues, may crack the transceiver’s back panel.

CHARGING THE BATTERY PACK (KSC-35S)

The battery pack is not charged at the factory; charge it before use.

ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger.

1 Plug the AC adapter cable into the jack located on the rear

of the charger.

2 Plug the AC adapter into an AC outlet. 3 Slide a battery pack or a transceiver equipped with a

battery pack into the charging slot of the charger.

• Make sure the metal contacts of the battery pack mate securely with the charger terminals.

• The indicator lights red and charging

Indicator

4 When charging is completed, the indicator lights green.

Remove the battery pack or the transceiver from the charging slot of the charger.

• It takes approximately 3 hours to charge the battery pack.

• When the charger will not be used for a long time, unplug the AC adapter from the AC outlet.

Note:

◆ When the indicator blinks red, the battery pack is either defective or the battery pack contacts are not properly mated with those of the charger.

◆ When the indicator ﬂ ashes green and orange, the battery pack has not satisﬁ ed the charging start temperature. Remove the battery pack from the charger and wait until it reaches a normal temperature before charging it again.

◆ The ambient temperature should be between 41°F and 104°F (5°C and 40°C) while charging is in progress. Charging outside this range may not fully charge the battery.

◆ The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack.

begins.

INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS

Install the cap over the speaker/ microphone jacks when not using an optional speaker/ microphone.

Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cap.

1 Place the cap over the jacks so that the locking tabs

insert into the transceiver grooves.

2 While holding the cap in place, push it towards the

bottom of the transceiver until the tabs on the cap click into place.

• To remove the cap, hold the top of the cap in place with your ﬁ nger while inserting a 2 mm or smaller ﬂ at blade screwdriver under the bottom of the cap. Slowly slide the screwdriver in until its tip touches the tab inside the cap, then gently pry the cap up (handle of screwdriver moving away from the transceiver) to remove the cap.

INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET)

Note: The transceiver is not fully water resistant when using a speaker/ microphone or headset.

1 Insert the speaker/ microphone (or

headset) plugs into the speaker/ microphone jacks of the transceiver.

2 Place the locking bracket over the

speaker/ microphone (or headset) plugs so that the locking tabs insert into the transceiver grooves.

• Push down on the locking bracket to slide it into place.

3 While holding the locking bracket in

place, push it towards the bottom of the transceiver until the tabs on the bracket click into place.

• To remove the locking bracket, push the bracket up from the base.

ORIENTATION

Microphone

Antenna

Speaker

Battery pack

a Channel selector Rotate to change the operating channel.

b LED indicator For the LED indicator status, refer to page 13.

c Power switch/ Volume control Turn clockwise to switch ON the transceiver. To switch OFF

the transceiver, turn counterclockwise until a click sounds. Rotate to adjust the volume level.

d PTT (Push to Talk) switch Press and hold, then speak into the microphone to transmit.

e Side 1 key Press to activate its programmable function {page 8}.

f Side 2 key Press to activate its programmable function {page 8}.

g Speaker/ microphone jacks Insert the Speaker/ microphone or Headset plug into this jack

{page 6}.

PROGRAMMABLE AUXILIARY FUNCTIONS

Your dealer can program the Side 1 and Side 2 keys each with one of the functions listed below.

Note: The duration of pressing a key to activate a function is dependent on your dealer setting. Your dealer may have set some keys to be held down for a short duration instead of being momentarily pressed. Ask your dealer for details on which keys need to be held down to activate their functions.

None

■

No function has been programmed.

Autodial

■

Autodial allows you to make a private DTMF call to another party.

Call 1/ Call 2

■

Press to send a FleetSync status, NXDN status, NXDN individual, 2-tone signaling call.

Calling Alert

■

A calling alert tone allows you to alert party members that you are making a call. When making a call, ﬁ rst hold down this key.

• While holding down the key, the calling alert tone will sound.

CW Message

■

Press to transmit the preset Morse code message on your current channel.

Emergency

■

Press and hold to enter (or exit) Emergency mode.

Key Lock

■

Press to lock/unlock the transceiver keys. Without Status Memory, when the transceiver power is turned OFF and then ON again, the Key Lock function will be cancelled.

Release the key to end the tone, then hold down the PTT switch and speak into the microphone to transmit.

+ 36 hidden pages