Kenwood Nexedge NXR-700, Nexedge NXR-800 Instruction Manual

NXR-700/ NXR-800

© B62-1994-00 (K)
Portuguese by Tectel

MANUAL DE INSTRUÇÕES

BASE-REPETIDORA DIGITAL VHF / BASE-REPETIDORA DIGITAL UHF

INSTRUCTION MANUAL

VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER

1

NXR-700 / NXR-800 INSTRUCTION MANUAL

VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER

THANK YOU!

We are grateful you purchased this Kenwood repeater. We
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
at peak effi ciency.

Kenwood incorporates the latest in advanced technology into
all of our products. As a result, we feel strongly that you will be
pleased with the quality and features of this product.

PRECAUTIONS

• Do not expose the unit to rain or moisture; to prevent fi re or
electric shock.

• Do not open the unit under any circumstances; to avoid risk
of electric shock.

• Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.

• Do not place the unit in excessively dusty and/or humid
areas, nor on unstable surfaces.

• If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately. Contact
your Kenwood service center or dealer.

NOTICES TO THE USER

◆

Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆

Illegal operation is punishable by fi ne and/or imprisonment.

◆

Refer service to qualifi ed technicians only.

FCC WARNING

This equipment generates or uses radio frequency energy. Changes
or modifi cations to this equipment may cause harmful interference
unless the modifi cations are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modifi cation is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.

•

Consult the dealer for technical assistance.

The AMBE+2 voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This voice
coding Technology is licensed solely for use within this Communications
Equipment. The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse engineer, or
disassemble the Object Code, or in any other way convert the Object
Code into a human-readable form. U.S. Patent Nos. #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,
#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579,
#5,226,084 and #5,195,166.

◆

This repeater is intended for use as a fi xed base station with

the antenna located outdoors on the rooftop or on an antenna
tower.

◆

This repeater is designed for a 13.8 V DC power source!

Never use a 24 V DC or higher source to power the repeater.

◆

Use only the supplied DC cord.

◆

Do not remove the ferrite core attached to the DC cord. Doing

so may cause interference with radio communications.

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking information is for use by your
Kenwood dealer, an authorized Kenwood service center, or the

factory.

Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, fi le a claim with the carrier immediately.

Item Part Number Quantity

Front glass B10-2781-XX 1
Dressed screw N08-0563-XX 1
Bracket J29-0725-XX 2
Flat head machine screw N32-4008-XX 4
Handle and screw set K01-0421-XX 1
DC cord E30-3344-XX 1
Lead wire with connector (15 pin) E37-1381-XX 1
Fuse (15 A) F05-1537-XX 1
Instruction Manual B62-1994-XX 1
Pamphlet B59-2457-XX 1
Pamphlet B59-2458-XX 1
Serial number sticker B42-7325-XX 1

INSTALLATION

To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.

Please consult your dealer for installing the repeater and
antenna.

MICROPHONE

Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood
microphone to the MICROPHONE jack on the front panel.

OCXO UNIT (KXK-3):Option

The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
(OCXO) unit.