Kenwood KDC-U6049, KDC-U6049L, KDC-U7049BTL, KDC-U7049BT User Manual

KDC-U7049BT KDC-U7049BTL KDC-U6049 KDC-U6049L

CD-RECEIVER

Quick Start Guide

AMCD



© 2010 Kenwood Corporation All Rights Reserved.			B59-2064-00/00 (MW)

Contents

Before use

Before use ..................................................	2
Preparations ..............................................	4
Basic operations.......................................	5
Playing music (CD/USB/iPod)..............	6
Listening to the radio ............................	7
Hands-free phoning ...............................	8
Installation accessories .......................	10
Before installation .................................	10
Connecting wires to terminals.........	12
Installation/Removal of the unit......	14
Installation of the Microphone Unit
..................................................................	15
Appendix .................................................	15

¤CAUTION

•Keep battery out of reach of children and in original package until ready to use. Dispose of used batteries promptly. If swallowed contact physician immediately.

•Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation may result.

•Do not set the remote control in hot places such as on the dashboard.

•Danger of explosion if Lithium battery is incorrectly replaced. Replace only with the same or equivalent type.

2 | Quick Start Guide

2WARNING

To prevent injury or fire, take the following precautions:

•Stop the car before operating the unit.

•To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.

¤CAUTION

•Adjust the volume so that you can hear sounds outside the car. Driving with the volume too high may cause an accident.

•Wipe off the dirt on the panel with a dry silicon or soft cloth.

Failure to observe this precaution may result in damage to the monitor or unit.”

Cleaning the connector

Wipe off dirt on the connector of the unit and panel. Use a cotton swab or cloth.

Condensation

When the car is air-conditioned, moisture may collect on the laser lens. This may cause disc read errors. In this case, remove the disc and wait for the moisture to evaporate.

Notes

•If you experience problems during installation, consult your Kenwood dealer.

•When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area.

•Characters that conform to ISO 8859-1 can be displayed.

•To display characters in the following

language, additional setting is required.

KDC-U7049BT KDC-U7049BTL

- Chinese

Refer to “Chinese” of <Initial setting> (page 22) (Instruction Manual).

•KDC-U6049 KDC-U6049L

-Arabic

-Persian

-Thai

Refer to “Language” of <Initial setting> (page 22) (Instruction Manual).

•The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.

About discs used with this unit

• This

only play the CDs with

•The following discs cannot be used:

-Discs that are not round

-Discs with coloring on the recording surface or discs that are dirty

-Recordable/Rewritable disc that has not been finalized (For the finalization process, refer to your disc writing software, and your disc recorder instruction manual.)

-8 cm (3 inch) disc (Attempt to insert using an adapter can cause malfunction.)

Handling discs

•Do not touch the recording surface of the disc.

•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

•Do not use any accessories for the disc.

•Do not use any solvents to clean discs. Use a dry silicon or soft cloth.

•Clean from the center of the disc and move outward.

•When removing discs from this unit, pull them out horizontally.

•Remove the rims from the center hole and disc edge before inserting a disc.

How to reset your unit

If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed.

Reset button

English | 3

Kenwood KDC-U6049, KDC-U6049L, KDC-U7049BTL, KDC-U7049BT User Manual

Preparations

Release Control knob (Volume knob)

[DISP]

Exit Demonstration Mode

Turn off the demonstration mode when you use it for the first time after installation.

Press the Control knob to quit the demonstration mode when the messages “To Cancel DEMO Press the volume knob” are displayed (approx. 15 seconds).

Turn the Control knob and press it when the “YES” is displayed.

The demonstration mode can also be canceled in the Function setting mode. Refer to <Demonstration mode Setting> (page 22) of Instruction manual

Adjusting the Clock

Press the [DISP] button several times to display the clock.

Press the [DISP] button for at least 1 second.

Turn the Control knob to adjust the hour, and then press the Control knob.

Turn the Control knob to adjust the minute, and then press the Control knob.

4 | Quick Start Guide

Detaching/ Reattaching the

Faceplate

Press the Release button.

•Remove the faceplate at once after pressing the Release button; otherwise it can fall down due to vibration.

•The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.

•Keep the faceplate in its faceplate case while detached.

•Do not place the faceplate (and the faceplate case) in areas exposed to direct sunlight, excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

Basic operations

KDC-U7049BT KDC-U6049

KDC-U7049BTL KDC-U6049L

[ ] [SRC] Control knob [ ] [ ] [iPod]

USB terminal

[DISP] [LOG]

Power

Turn the power ON by pressing the [SRC] button.

Press the [SRC] button for at least 1 second to turn the power OFF.

Source selection

Press the [SRC] button each time switches between sources.

Tuner (“TUNER”) USB (“USB”) or iPod (“iPod”) CD (“CD”) Auxiliary Input (“AUX”) Standby (“STANDBY”) Tuner...

When an optional accessory is connected, the source name for each device appears.

KDC-U6049 KDC-U6049L

Press the [iPod] button to switch the source to iPod.

The source “iPod” and “CD” can be selected when each source is ready to play.

Volume

Turn the Control knob to adjust the sound volume.

USB terminal

USB device or iPod can be connected. CA-U1EX or KCA-iP102 (optional accessories) is recommended to connect a USB device or iPod.

Auxiliary input

Portable audio device can be connected with the stereo mini-plug (3.5 mm ø).

Display selection

Every time the [DISP] button is pressed, the display switches among 5 types. You can switch the information to be displayed. Refer to <Display settings> (page 16) of Instruction manual

Display scroll

Keep the [DISP] button pressed down to scroll through the CD or audio file text display.

Log memory recall

Previously used functions are automatically logged in memory and displayed as the list.

Press the [LOG] button.

Turn the Control knob and press it when the desired Log memory is displayed.

To cancel Log memory recall, press

[].

Logs can be saved or deleted. Refer to <Log memory> (page 15) of Instruction manual.

English | 5

Playing music (CD/USB/iPod)

[ ] [SRC] Control knob Disc slot

[0]

[]

Playing disc

Insert the disc in the Disc slot.

When inserted, the source is switched automatically and a song starts playing.

Playing USB device/ iPod

Connect a USB device or iPod to the USB terminal.

When connected, the source is switched automatically and a song starts playing.

Selecting an audio file folder

Push the Control knob towards up or down to select a folder.

Selecting a song

Push the Control knob towards right or left to select a song (track or file).

Fast Forward or Fast Backward of the Song

Press and hold the Control knob towards right or left to fast-forward or fast-backward the audio file containing songs (tracks or files).

Pause and play

Press the [] button to pause or resume playing a song (track or file).

USB Terminal

Music search

Searching for the song you want to play.

Press the [] button.

Search for music.

Operation type	Operation
Movement between items	Turn the Control knob.
Selection of item	Press the Control knob.
Return to previous item	Press the [	] button.

To cancel the music search operation of Audio file or iPod, press the [] button for at least 1 second.

Removing Disc

Press the [0] button to eject a disc.

Removing USB device

Press the [SRC] button to switch the source to the device other than USB, and then remove the USB device.

Data contained in the USB device may be damaged when you remove it while it is used as the active source.

6 | Quick Start Guide

Listening to the radio

[SRC]

Control knob [PRESET]

Selecting a tuner source		and then press the Control knob for at
Press the [SRC] button to select “TUNER”.		least 2 seconds.
Selecting the band	Recalling the stations in the
Push the Control knob towards down to	memory
change the band (FM or AM).		Push the Control knob towards down to
Selecting a station		Push the Control knob towards down to
Selecting a station		change the band (FM or AM).
Push the Control knob leftward and		Press the [PRESET] button.
rightward to select the station you want

	to listen to.	Turn the Control knob to select preset
		number (FM: “01” – “18”, AM: “01” – “06”),
	The tuning mode can be changed. Refer
		and then press the Control knob.
	to <Seek mode setting> (page 13) of

	Instruction manual

Station preset memory

Push the Control knob towards down to change the band (FM or AM).

Push the Control knob leftward and rightward to select the station you want to memory.

Press the [PRESET] button.

Press the [PRESET] button again to enter the Mix Station preset mode. In this mode, FM and AM can be saved in the same preset layer, which allows

you to recall the desired station without switching the bands or tuner sources. Maximum of 6 stations can be preset in the Mix Station preset mode.

Turn the Control knob to select preset number (FM: “01” – “18”, AM: “01” – “06”),

English | 7

Function of KDC-U7049BT, KDC-U7049BTL, KCA-BT200/BT300 (Optional Accessory)

Hands-free phoning

KDC-U7049BT KDC-U6049

KDC-U7049BTL KDC-U6049L

[SRC]

Control knob [ ] [ ] [iPod]

[LOG]

Registering cell-phone

KDC-U7049BT KDC-U7049BTL

Press the [] button for at least 1 second.

The search for a cell-phone starts. It takes a while (tens of seconds or several minutes) to complete.

Press the Control knob when the model name of a cell-phone to use is displayed.

Enter the PIN code of your cell-phone.

Operation type

Select the numbers.

Move to the next digit.

Delete the last digit.

Transmit the PIN code.

Operation

Turn the Control knob.

Push the Control knob towards right.

Push the Control knob towards left.

Press the Control knob.

The connection to your cell-phone starts, after a while “HF Connect” is displayed, and then returns to the previous source. When registration of your cell-phone is complete, the phone book of the cellphone is automatically downloaded

to this unit. (If the phone book has not been downloaded to this unit, operate the cell-phone to download it.)

KDC-U6049 KDC-U6049L

By operating the cell-phone, register the hands-free unit (pairing). Select “KCA-BT200” or “KCA-BT300” from the list of connected units.

Enter the PIN code of this unit from the cell-phone.

The PIN code of this unit is “0000” by default.

When registration of your cell-phone is complete, the phone book of the cellphone is automatically downloaded to this unit. (If the phone book has not been downloaded to this unit, operate the cell-phone to download it.)

Error code list

•“Device Full”:

5 Bluetooth devices have already been registered. No more Bluetooth devices are registered.

•“PIN Code NG”:

The PIN code is wrong.

•“Connect NG”:

The unit cannot be connected to the device.

•“Pairing Failed”: Pairing error.

•“Confirm phone”:

Your cell-phone prompts you to confirm.

8 | Quick Start Guide

Calling a number in the Phone book

Dial the phone number in the phone book of your cell phone.

If the phone book has not been downloaded to this unit, operate the cellphone to download it.

KDC-U7049BT KDC-U7049BTL

Press the [ ] button.

KDC-U6049 KDC-U6049L

Press the [LOG] button for at least 1 second.

Turn the Control knob and press it when the “Phone Book” is displayed.

Turn the Control knob to select phone number.

Push the Control knob towards right or left to select the name of the called party.

Operation type		Operation
Select the Phone number.		Turn the Control knob.
Select the initial.		Push the Control knob
		towards up or down.

Determine the Phone number. Press the Control knob.

KDC-U7049BT KDC-U7049BTL

Press the [ ] button.

KDC-U6049 KDC-U6049L

Press the Control knob.

Answering a phone call

KDC-U7049BT KDC-U7049BTL

Press the [ ] button.

KDC-U6049 KDC-U6049L

Press the Control knob.

Disconnecting a call

KDC-U7049BT KDC-U7049BTL

Press the [

] button.

KDC-U6049 KDC-U6049L

Press the [SRC] button.

English | 9

Installation accessories Before installation

12WARNING

• The unit can only be installed in a car with

.....1

.....2

.....4

5 (KDC-U7049BT, KDC-U7049BTL only)

.....1 (3m)

10 | Quick Start Guide

a 12V DC power supply, negative ground.

•If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

¤ CAUTION

•Install this unit in the console of your vehicle.

•Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.

•Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.

•If you experience problems during installation, consult your Kenwood dealer. Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

•Insulate unconnected wires with vinyl tape or other similar materials. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

•Be sure to ground this unit to the car’s chassis again after installation.

•If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one with the same rating.

•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the +

+ 22 hidden pages