Kenwood HM-331 User Manual
MICRO HI-FI COMPONENT SYSTEM
HM-331
INSTRUCTION MANUAL
KENWOOD CORPORATION
COMPACTCOMPACT
DIGITAL AUDIODIGITAL AUDIO
TEXT
B60-4228-00 00 CH (M,T) OC 9809
2
Before applying power
Units are designed for operation as follows.
Europe and U.K. .................................................. AC 230V only
*Other countries...........AC 110-120 / 220-240 V switchable
Caution : Read this page carefully to ensure safe operation.
HM-331 (En/T)
For the United Kingdom
Factory fitted moulded mains plug
1.The mains plug contains a fuse. For replacement, use
only a 3-Amp ASTA-approved (BS 1362) fuse.
2.The fuse cover must be refitted when replacing the
fuse in the moulded plug.
3.Do not cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in
your home or the cable is too short to reach.
A power point, then obtain an appropriate safety
approved extension lead or adapter, or consult your
dealer. If nonetheless the mains plug is cut off, remove
the fuse and dispose of the plug immediately, to
avoid a possible shock hazard by inadvertent.
Connection to the mains supply.
Preparation section
IMPORTANT :
The wires in the mains lead are coloured in
accordance with the following code:
Blue : Neutral
Brown : Live
Do not connect those leads to the earth terminal of a
three-pin plug.
*For other countries
AC voltage selection
The AC voltage selector switch on the rear panel is set to
the voltage that prevails in the area to which the unit is
shipped. Before connecting the power cord to your AC
outlet, make sure that the setting position of this switch
matches your line voltage. If not, it must be set to your
voltage in accordance with the following direction.
AC voltage selector switch
AC 110–120V AC 220–240V
Move switch lever to match your line voltage with a small
screwdriver or other pointed tool.
Note:
Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.
Safety precautions
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The marking is located on the rear panel and says that
the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser
beams that are of a weaker class. There is no danger of
hazardous radiation outside the unit.
Contents
Preparation section Application section
Caution : Read this page carefully to ensure safe operation.
Before applying power
HM-331 (En/T)
3
Before applying power............................... 2
Safety precautions ........................................................... 2
Special features ................................................................ 4
Handling of discs .............................................................. 5
Notes on cassette tape .................................................... 5
System connection........................................... 6
Connection of the System Accessories ....................... 6
Connection of Other Accessories
(Commercially Available Parts) ............................... 8
Controls and indicators ................................... 9
Display ................................................................................ 9
Main unit........................................................................... 10
Remote control Unit.........................................................12
Operation of remote control unit ................. 13
CHANNEL SPACE setting................................................13
Basic section
Let's put out some sound............................... 14
Basic use method............................................................ 14
Playback of CD ................................................................ 16
In regard to CD-TEXT ...................................................... 17
Playback of tape.............................................................. 18
Receiving broadcast station ..........................................20
Let's recording ................................................ 22
Recording on TAPE ..........................................................22
Playback of CD................................................ 24
Listening in the desired sequence
(program playback)................................................... 24
Repeated playback ..........................................................25
Listening to an unexpected title sequence
(random playback) .....................................................26
R.D.S. (Radio Data System)
(Except for some areas) ........................................................
Searching for a desired program type
(PTY search) ............................................................... 29
To be able to listen to the desired information
at any time ................................................................... 31
28
Convenient Recording Methods .................. 33
Selection of the Recording type....................................33
One-touch recording (CD
Program recording (CD
=
TAPE) ................................34
=
TAPE).................................. 35
Tone adjustment ............................................. 36
Tone adjustment .............................................................. 36
Balance adjustment........................................................ 36
Adjusting the AUX Input Level.......................................37
Clock adjustment............................................ 38
Timer operation................................................ 39
Setting the O.T.T................................................................39
Setting the Program Timer ............................................ 40
Activating or deactivating the O.T.T. or
program timer execution ......................................... 42
Sleep timer ....................................................................... 42
Preparation section
Knowledge section
Important Items............................................... 43
Maintenance .....................................................................43
Reference ..........................................................................43
In case of difficulty ........................................ 44
Specifications ............................................ 47
4
Before applying power
HM-331 (En/T)
Special features
CD player and auto-reverse cassette deck as standard equipment
A CD player and auto-reverse cassette deck are provided, making the unit an integrated micro stereo system for
enjoyment of multiple music sources.
Convenient Recording Methods
Various versatile recording functions are provided according to the use purposes.
÷One-touch recording : Recording of one CD or one track by pressing a single key
÷Program recording : Any desired tracks can be recorded in the desired sequence
Convenient timer functions
Two-program timer : Timer playback, timer recording and AI timer playback can be programmed.
AI timer : When the unit is turned ON by the timer, the sound level increases gradually.
O.T.T. : Timer with easy setting, which operates only once.
Sleep timer : Useful when you want to go asleep while listening to music.
Preparation section
In regard to demonstration
set/demo
This unit is equipped with a demonstration function
(only display). The demonstration consists of sequential change of display and indicators showing the
operations, but the audio itself does not change. The
demonstration function can be cancelled as follows.
÷ Even when DEMO is ON, stations with weak radio waves are muted and their sound cannot be heard.
÷ This operates automatically when a power failure has occurred or the plug of the power cable has been pulled while
the power was ON. Cancellation is possible by pressing the key during the demonstration.
DEMO OFF (To cancel demonstration):
Press the “set/demo” key when DEMO is ON.
DEMO ON (To execute demonstration):
After turning power ON, press and hold the
“set/demo” key (for more than 2 seconds).
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately.
If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company
receiving the unit) can file a claim against the carrier for shipping damage.
We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.
Accessories
FM indoor antenna (1) Loop antenna (1) Remote control unit (1)
Europe, and U.K. Other countries
Please confirm that the following accessories are present.
Batteries (R6/AA) (2)
*AC plug adaptor (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where
use is necessary.)
Handling of discs
Before applying power
HM-331 (En/T)
5
Disc handling precautions
Handling
Hold the discs so that you do not
touch the playing surface.
Label side
Playing side
Sticker
Sticky paste
Do not attach paper or tape to either the playing side or the label side
of the discs.
Cleaning
If fingerprints or foreign matter become attached to the disc, lightly
wipe the disc with a soft cotton cloth
(or similar) from the center of the disc
outwards in a radial manner.
Storage
When a disc is not to be played for
a long period of time, remove it from
the player and store it in its case.
Discs which can be played with this unit
CD (12 cm, 8 cm), and the audio part of CDV, CD-G, CD-EG
and CD-EXTRA.
Use discs that comply with the IEC standard, for example
a disc carrying the
COMPACTCOMPACT
marking on the label surface.
DIGITAL AUDIO
Never play a cracked or warped disc
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed
disc or a disc repaired with tape or adhesive agent.
Please do not use discs which are not round because they
may cause a malfunction.
Disc accessories
The disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound
quality or protecting discs as well as the disc cleaner should
not be used with this system because they may cause
malfunction.
Preparation section
Notes on cassette tape
Safety tab (accidental erasure prevention tab)
After an important recording has been finished, break the
safety tab, to prevent the recorded contents from being
erased or recorded on accidentally.
For A side
For B side
To re-record
1.Longer tape than 110 minutes cassette tape
Notes
Notes
2.Endless tapes
Since longer tape than 110 minutes cassette tape is very thin, the tape could adhere to the pinch roller or be
easily broken. It is recommended that these tapes not be used with this unit to prevent possible damage.
Do not use an endless tape, as this could damage the mechanism of the unit.
Apply tape only to the position where
the tab has been removed.
To store cassette tapes
Do not store the tapes in a place which is subject to
direct sunlight, or near equipment that generates heat.
Keep the cassette tapes away from any magnetic field.
N
S
When there is slack in the tape
In such a case, insert a pencil into the reel hole and wind
the reel hub to remove the slack.
6
System connection
HM-331 (En/T)
Connection of the System Accessories
This figure shows the method of connection between the main unit and provided accessories.
AM loop antenna
The supplied antenna is for indoor use. Place it as far as
possible from the main system, TV set, speaker cords and
power cord, and set it to a direction which provides the best
reception.
12 3 4
Preparation section
CAUTION
Connect the components as shown in the
diagram.
Only plug the power cord into a power outlet
once connections are completed.
Note on Connection
Malfunction of microcomputer
If operation is not possible or erroneous display
appears even though all connections have
been made properly, reset the microcomputer
referring to “In case of difficulty”.
¤ r
Notes
Notes
1.Never short-circuit the “+” and “-” speaker cords.
2.If the left and right speaker connections or the “+” and “-” polarity
are inverted, the sound will be unnatural with unclear positioning of
musical instruments, etc. Be sure to connect them without mistake.
3.Be sure to insert all connection cords securely. If their connections
are imperfect, the sound may not be produced or noise may
interfere.
4.Before plugging or unplugging a connection cord, be sure to unplug
the power cord from the wall AC outlet. If connection cords are
plugged or unplugged with the power cord left plugged in, malfunction
or damage may result.
Speaker (right)
Main Unit
1234
Twist
System connection
HM-331 (En/T)
FM indoor antenna
The accessory antenna is for temporary indoor use only. For stable signal reception we recommend using an outdoor antenna.
Remove the indoor antenna if you connect one outdoors.
1Remove the insulation from the end of the cord end.
(Except for Europe, and U.K.)
Europe, and U.K.
FM
75Ω
2Connect it to the antenna terminal.
3Locate the position providing good reception condition.
4Fix the antenna.
Other countries
7
Preparation section
GND
FM
75Ω
DIGITAL
OUT
OPTICAL
ANTENNA
AUX INPUT
R L
300Ω
FM
AM
AM
GND
FM
75Ω
GND
SPEAKERS
(
6–16
+
L
–
–
R
+
SUPER
WOOFER
PRE OUT
MANUAL
)
Ω
PANEL
OPEN/CLOSE
AUTO
FM
300Ω
AM
SPEAKERS
(6–16Ω)
+
L
–
–
R
+
Speaker (left)
AC 110–120V AC 2 20–240V
Speaker cord
Connect correctly + to + and - to -.
PANEL OPEN/CLOSE switch
Change the operation mode of the "REVOLVING
CONTROL PANEL". !
POWER cord
TO WALL AC
OUTLET
2
2
8
System connection
HM-331 (En/T)
Connection of Other Accessories
CAUTION
Connect the components as shown in the diagram.
Only plug the power cord into a power outlet once
connections are completed.
DIGITAL OUT jack
(OPTICAL)
Preparation section
Note on Connection
DIGITAL
OUT
OPTICAL
Other countries
300Ω
FM
75Ω
GND
FM
AM
(Commercially Available Parts)
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna
into the room and connect it to the
FM 75Ω terminal. Please remove the
indoor antenna after an outdoor antenna has been installed.
10mm 10mm
Antenna adaptor (optional)
FM
75Ω
Optical-fiber
cable
Cap
If necessary, remove the
cap and plug the opticalfiber cable (optional)
Optical-fiber cable
MD recorder or
DAT etc.
AUX INPUT
R L
GND
FM
75Ω
DIGITAL
OUT
OPTICAL
ANTENNA
AUX INPUT
R L
300Ω
SPEAKERS
AM
(
)
Ω
6–16
FM
AM
+
L
–
–
R
+
SUPER
WOOFER
PRE OUT
MANUAL
GND
PANEL
OPEN/CLOSE
AUTO
Europe, and U.K.
SUPER WOOFER
AC 110–120V AC 2 20–240V
POWER cord
TO WALL AC OUTLET
Audio output
VCR, Analog turntable with built-in
RIAA equalizer (optional P-110), etc.
Audio cord
Notes
Notes
1.In case an associated system component is connected, also read
the instruction manual of the component.
2.Insert the optical-fiber cable straight into the connector until it clicks.
3.Be sure to attach the protection cap when the connector is not used.
4.Never band or bundle the optical-fiber cable.
Controls and indicators
(The displays given in this manual are approximations only.
Display
They may differ from what actually appears on the display.)
9
HM-331 (En/T)
8#@
1
2
RANDOM
FM
A
M
PM
• • • • • • • • • • •
PGM
REPEAT ALL SLEEP
AUTOTOTALTRACK NO.
A.P.S.
TUNED
88888888
34567
1 Tuner-related indicators
2 Character information display section (dot display)
Shows character information including the input selection,
volume level and disc/track title.
3 Character information display section
Frequency indication, time indication, track No., program No.,
etc.
4 O.T.E. (ONE TOUCH EDIT) indication
Appears during one-touch recording.
5 LOUD (Loudness) indication
6 TAPE REC indicators
7 EX.BASS (extra bass) indication
!09
O.T.T. PROG.
STEREO
kHz
MHz
1 2
R·D·S EON NEWS
TA PTY
TP
O.T.E.
TITLE SEARCH
MD EDIT
8 Indication related to CD
9 Auto Power Save indicator
0 Timer-related indicators
! RDS-related indication (expect for some areas)
@ Cassette deck, reverse mode and TAPE equalizer
(T.E.) indicators
# CD play/pause indicators
Indicates the play and pause modes of CD.
T.E.NR
Preparation section
10
Controls and indicators
HM-331 (En/T)
Main unit
2
Preparation section
3
4
5
TAPE rec
menu
set / demo
4
1
TAPE / preset
TUNER / band
AUX
4
1
0
push open
CD TAPE
O.T.E.
repeat sound
1
#
$
%
^
6
7
8
9
0
!
@
open / close
panel
tape
EQ.
direction
2
TAPE
Auto Reverse
phones
&
VOLUME / multi control
CD
6
2
STOP
7
on/standby
d
o
w
n
0
push open
p
u
*
(
)
¡
About the one-touch operation function
This unit incorporates the one-touch operation function for the user's convenience.
With this function, pressing any key enclosed in while the unit is in standby mode
immediately start playback (or reception).
Controls and indicators
HM-331 (En/T)
11
1 CD cover open key (0)
Press to open the CD player cover.
2 Display
3 Tape record key (TAPE rec)
Press to start recording. Pressing the key during recording
stops it after leaving a non-recorded space (blank) of about 4
seconds.
4 “set/demo” key
Press to set or enter an item selected with the “VOLUME/
multi control“.
Used for demonstration ON/OFF.
5 “menu” key
Press to switch the function of the “VOLUME/multi control
(up/down)” knob.
This key is also used when setting the time of the day.
6 “panel open / close” key
7 ”tape EQ” key
8 CD play/pause key (CD 6)/indicator
Press to select the CD input and start CD playback.
Press during CD playback to let it pause temporarily.
9 Tape play key (TAPE)/
TAPE direction indicator
0 Stop key (7)
! Cassette holder
Press the area marked “0 push OPEN” to load or eject a tape.
@ “phones” jack
Headphones with a stereo mini plug (optional) can be
connected.
£
^
# CD Skip (4, ¢)/TAPE (1, ¡) keys &)
During CD operation :
Press to skip tracks in the forward or backward direction.
During TUNER operation :
Press to receive a preset station.
During TAPE operation :
Press to search in the forward or backward direction.
$ “repeat” key ∞
Used for repeated playback of CD.
% O.T.E. key
^ “sound” key
Used for switching the EX.BASS play and LOUDNESS play.
& “TUNER/band” key )
The received broadcasting band is switched.
Press to select the TUNER input.
AUX input key
Press to listen to the input source connected to AUX (analog
external).
* Standby / timer indicator $
Light in standby mode of power.
Red :Normal standby mode
Orange :O.T.T. standby
:Program timer standby
Green :Power ON mode
( “VOLUME/multi control (up/down)” knob $
*
Normally this is used for volume adjustment.
) Remote sensor
¡ “on/standby” key
The system is switched ON and STANDBY.
%
Preparation section
* About the VOLUME/multi control (up/down) knob
Turning the knob switches the function as shown
After selecting the function of this knob with the
“menu” key, select the desired control item by turn-
ing the “VOLUME/multi control (up/down)” knob.
To set or enter the setting of the selected item, press
the “set/demo” key.
menu
VOLUME / multi control
in the character information display.
TAPE RVS. ?
O.T.E. ? ›
A. MEMORY (or A. PRESET) ? ¡
(Only when the TUNER input is selected)
AUX LEVEL ?
(Only when the AUX input is selected)
BALANCE ?
TIMER SET ? ·
set/demo
A.P.S. SET ? %
÷ The function of the control knob returns to the normal
mode when it has not been operated for 5 seconds.
About the REVOLVING CONTROL PANEL
AUTO MANUAL
÷The REVOLVING CONTROL PANEL is closed when
the power supply is in STANDBY mode.
÷When the power is switched ON, the REVOLVING
CONTROL PANEL opens.
÷When the power is ON, the panel opens and closes
alternately each time the "panel open / close" key is
pressed.
÷When the power is ON, the panel opens and closes
alternately each time the "panel open / close" key
is pressed.
MANUAL AUTO
ANTENNA
FM
300Ω
FM
75Ω
AM
GND
DIGITAL
OUT
OPTICAL
(
‡
fl
open / close
panel
SPEAKERS
(
)
6–16
Ω
+
L
–
–
R
+
+
SUPER
WOOFER
PRE OUT
AUTO
MANUAL
PANEL
OPEN/CLOSE
2
2
REVOLVING CONTROL PANEL
(close state)
2
2
12
Remote control unit
6
AUX
CD
P.CALL
POWER
RANDOM
DOT DISP.TIME DISP.
¢
%
VOLUME
fi
9
0
!
@
#
1
2
SLEEP TONE SOUND
1 2 3 TIMER
4 5 6 REPEAT
3
4
5
Preparation section
6
7
8
Europe, and U.K.
RC-F0503E (Infrared ray system)
Other countries
RC-F0503 (Infrared ray system)
1 TONE key fl
This is used to adjust the tone.
SOUND key %
Used for switching the EX.BASS play and LOUDNESS play.
2 SLEEP key w
This is used to set the sleep timer.
3 Numeric keys
These are used to select CD tracks and as preset call keys for
the tuner.
4 TAPE O.T.E. key ›
These keys are used for recording of a CD onto tape with a
one-touch operation.
Press either key during CD playback to record the currently
played track onto tape. Press in stop mode to record the entire
CD onto tape.
7 8 9
+10 0 PGM CLEAR
TAPE
O.T.E.
¡ 4
1
TAPE
TUNER
2 3 7
BAND
PTY
TA/NEWS
SET ENTER MUTE
REMOTE CONTROL UNIT
RC-F0503E
Controls and indicators
HM-331 (En/T)
The keys on the remote control unit with the same names as on the
main unit have the same function as the keys on the main unit.
5 Basic operation keys
Fast forward, fast reverse keys (1, ¡)
During CD or TAPE operation: &(
Press to search in the forward or backward direction.
During TUNER operation:
Press to select a radio station.
P.CALL/skip keys (4, ¢)
During CD operation : &
Press to skip tracks in the forward or backward direction.
During TUNER operation:
Press to select a radio station.
TAPE 2 3 key
TUNER BAND key
CD 6 key
Stop key (7)
AUX key
6 RDS-related keys (For Europe and U.K.)
TA/NEWS key
Used at the time of EON reservation.
PTY key ª
Used at the time of program type detection.
7 SET key
Press to set or enter an item selected with the “VOLUME/
multi control“.
ENTER key ¡
It is used to enter the preset station memory in the tuner.
8 MUTE key %
This is used to suppress the sound temporarily.
9 POWER ( ) key $w
The system is switched ON and STANDBY.
This key is also used to activate or cancel the timer program
execution.
0 TIMER key w
Used to select the timer.
! Keys related to CD
REPEAT key
This is used for repeated playback.
RANDOM key §
Playback of the CD tracks in random order.
CLEAR key ¢
The programmed track sequence is cleared.
PGM key \¢
This is used to program the track sequence.
During TUNER operation: ¡
Used to switch the tuning mode between “AUTO” (auto
tuning, stereo reception) and Manual (manual tuning,
monaural reception).
@ TIME DISP. key
Press to switch the time information displayed during CD
playback.
DOT DISP. key ¶
Used for scroll display of the text infomations of CD-TEXT
compatible disc.
# VOLUME (%,fi) keys
)
)
⁄
∞
Operation of remote control unit
CHN SPACE• •
STEREO
FM
PM
A
M
MHz
kHz
BEST HITS
TUNED
RANDOM
PGM
REPEAT ALL SLEEP
A.P.S.
O.T.T. PROG.
AUTOTOTALTRACK NO.
02119050
Loading batteries
÷ Insert two R6 (“AA”-size) batteries following the
polarity indications.
Operation
After plugging the power cord of this unit, press
the POWER (
turn the system ON. When the system is turned
ON, press the key of the function to be operated.
) key of the remote control unit to
Operating range
(approx.)
13
HM-331 (En/T)
3 Close the cover.1 Remove the cover. 2 Insert batteries.
Preparation section
2
2
Remote sensor
÷ When pressing more than one remote control keys
successively, press the keys securely by leaving an
interval of 1 second or more between keys.
1.The provided batteries are intended for use in operation checking, and their service life may be short.
Notes
Notes
2.When the remote controllable distance becomes short, replace both of the batteries with new ones.
3.If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote
sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.
Channel space switching
(Except for
The space between radio channels has been set to the one that
prevails in the area to which the system is shipped. However, if the
current channel space setting does not match the setting in the area
where the system is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice versa, proper
reception of AM/FM broadcasts cannot be expected. In this case,
change the channel space setting in accordance with your area by
referring to the following table.
the United Kingdom and Australia)
6m
30˚
30˚
1 Turn power on.
2 Press the TUNER/band key
3 Select the mode by using the "repeat" key.
Each press switches the space frequency alternately.
1 "FM 50 kHz" (FM 50 kHz, AM 9 kHz)
2 "FM 100 kHz" (FM 100 kHz, AM 10 kHz)
Area
USA, Canada and South
1
American countries
2
Other countries
CHANNEL
Space Frequency
FM: 100 kHz
AM: 10 kHz
FM: 50 kHz
AM: 9 kHz
Blinks.
4 Establish the selection by pressing the "set/
demo" key.
14
Let's put out some sound
Basic use method
Bass and treble compensation "sound" key
22
HM-331 (En/T)
2
2
33
11
Basic section
Example:
To select the CD input
VOLUME / multi control
on/standby
CD
6
11
Lights
22
Listening through headphonesMuting the sound temporarily
1. Set the “on/standby” key to ON (STANDBY).
When the “on/standby” key ( ) is pressed while the unit is ON,
the unit is switched off.
÷ Pressing the CD 6, AUX, TAPE or “TUNER/band” key also turns power
on and starts playback (reception) of the corresponding input. (One-touch
operation)
÷ When the CD or TAPE input is selected while the corresponding disc or tape
has been loaded, it immediately starts to play.
2. Selecting the desired output.
TUNER (Broadcasts) )
CD ^
TAPE *
AUX (External input) 8
÷ Pressing the CD 6, AUX, TAPE or
“TUNER/band” key selects the cor-
responding input.
3. Volume adjustment.
d
o
The volume
decreases
÷ Quick turning produces a larger
33
w
n
p
u
The volume
increases
change amount. (Dynamic rotary volume control function)
÷ The display shows a reference value.
Let's put out some sound
S
HM-331 (En/T)
15
Listening through headphones
Insert the headphone plug into the “phones”
jack.
phones
÷ Headphones with a stereo mini plug can be con-
nected.
÷ The sounds from all speakers are cut off.
Muting the sound temporarily
MUTE
RANDOM
÷ Press again to resume the original volume.
÷ This is also cancelled when the volume is changed.
(Remote control unit only)
Blinks
PGM
REPEAT ALL
Standby mode
Bass and treble compensation
sound
EX.BASS
Each press switches the modes as follows.
1 “EX.BASS” (Extra Bass) lights.
The lowest and highest frequencies are enhanced regardless of the current volume
level.
2 “LOUD” (Loudness) lights.
The lowest and highest frequencies are enhanced according to the current volume level.
(Effective during low-volume listening.)
3
Both indicators off.
Sound enhancement mode is disengaged.
÷ Adjusting the tone while the “LOUD” or “EX.BASS”
indicator is lit turns it off and cancels the sound
enhancement mode. fl
LOUD
or
AUTO POWER SAVE function
When the unit is ON and the unit is left for 30 minutes with CD and TAPE not operating, the unit is
switched off automatically by this function. This is
convenient when you forgot to switch off the unit.
This function can be activated or deactivated by the
following operation.
Basic section
When the standby/timer indicator on the main unit
lights in red or orange, a minute current flows for
memory protection. This condition is called standby
mode.
RANDOM
PGM
REPEAT ALL SLEEP
FM
A
M
8 0180000
PM
A.P.S.
TUNED
AUTOTOTALTRACK NO.
kHz
MHz
CD• • • • • • • • •
1 2
O.T.T. PROG.TPR·D·S EON EON
STEREO
BEST HITS O.T.E.
TA PTY
TITLE SEARCH
MD EDIT
T.E.NR
When CD has been selected.
RANDOM
PGM
REPEAT ALL SLEEP
FM
A
M
8 0180012
PM
A.P.S.
TUNED
AUTOTOTALTRACK NO.
kHz
MHz
VOLUME• 20• •
1 2
O.T.T. PROG.TPR·D·S EON EON
STEREO
BEST HITS O.T.E.
TA PTY
TITLE SEARCH
MD EDIT
T.E.NR
Volume display
1 Select “A.P.S. SET?”.
VOLUME / multi control
menu
( Press the “set/demo” key while the “?” mark
is blinking.)
2 Select.
A.P.S. off A.P.S. on
A.P.S.
VOLUME / multi control
d
o
w
n
u
A.P.S.
p
LightsGoes off
3 Set it.
set/demo
÷ When the TUNER or AUX input is selected, APS
operates only when the volume is set to zero or when
MUTE is on.
Loading...