Kenwood FP691 User Manual

FP691 & FP698
P
8
1
2
3
4
5
6
7
0
1
2
liquidiser
filler caplidjugsealing ringblade unit
additional attachments
Not all of these attachments listed below will be included with your food processor. Please refer to your content list supplied. To buy an attachment not included in your pack, contact the dealer from whom you purchased your appliance.
knife bladedough tooltwin beater geared whiskmaxi-blend canopythick slicing/coarse shredding discthin slicing/fine shredding discfine (Julienne style) chipper discextra coarse shredding disc (UK - not available)rasping discstandard chipper disc (UK - not available)geared citrus pressspatuladisc storage boxmulti millcentrifugal juicerrecipe book
to use your food processor
1 Fit the detachable shaft onto the power unit . 2 Then fit the bowl. Place the handle towards the back and turn clockwise until it
locks .
3 Fit an attachment over the drive shaft.
Always fit the bowl and attachment onto the machine before adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft locates into the centre of the lid.
Do not use the lid to operate the processor, always use the on/off speed control.
5 Switch on and select a speed.
The processor won’t work if the bowl and lid are fitted incorrectly.
Use the pulse control for short bursts. The pulse will operate for as long as the lever is held down.
6 Reverse the above procedure to remove the lid, attachments and bowl.
Always switch off before removing the lid.
important
Your processor is not suitable for crushing or grinding coffee beans, or converting granulated sugar to caster sugar.
When adding almond essence or flavouring to mixtures avoid contact with the plastic as this may result in permanent marking.
to use your liquidiser
1 Fit the sealing ring into the blade unit . 2 Screw the jug onto the blade unit. 3 Put your ingredients into the jug. 4 Put the filler cap in the lid, then turn. 5 Lock the lid onto the jug so that the thumb tab is over the handle (To unlock the
lid, push the thumb tab .)
6 Place the liquidiser onto the power unit and turn to lock . 7 Select a speed or use the pulse control.
21
22
23
24
25
26
27
28
29
30
31
a
safety
The blades and discs are very sharp, handle with care.
Always hold the knife blade by the finger grip at the top, away from the cutting edge, both when handling and cleaning.
Always remove the knife blade before pouring contents from the bowl.
Keep hands and utensils out of the processor bowl and liquidiser jug whilst connected to the power supply.
Switch off and unplug:
before fitting or removing parts
after use
before cleaning
Never use your fingers to push food down the feed tube. Always use the pusher/s supplied.
Before removing the lid from the bowl or liquidiser/mill from the power unit:-
switch off;
wait until the attachment/blades have completely stopped;
Be careful not to unscrew the liquidiser jug or mill from the blade unit.
Allow hot liquids to cool before blending in the liquidiser - if you haven’t fitted the lid securely and it comes off, you could get splashed.
Do not use the lid to operate the processor, always use the on/off speed control.
This machine will be damaged and may cause injury if the interlock mechanism is subjected to excessive force.
This machine is not intended for use by young children or infirm persons without supervision.
Never use an unauthorised attachment.
Don’t let children play with this machine.
Never leave the machine on unattended.
Never use a damaged machine. Get it checked or repaired: see ‘service’.
Never let the power unit, cord or plug get wet.
Don’t let excess cord hang over the edge of a table or worktop or touch hot surfaces.
Never misuse your food processor and only use it for its intended domestic use.
before plugging in
Make sure your electricity supply is the same as the one shown on the underside of your machine.
important- UK only
The wires in the cord are coloured as follows: Blue = Neutral Brown = Live
This appliance complies with European Economic Community Directive 89/336/EEC.
before using for the first time
1 Remove all packaging including the plastic blade covers from the knife blade.
Take care the blades are very sharp. These covers should be discarded
as they are to protect the blade during manufacture and transit only. 2 Wash the parts see ‘cleaning’ 3 Push excess cord into the back of the machine.
key
processor
power unitdetachable drive shaftbowllidfeed tubepusherssafety interlockcord storagepulse controlspeed control
a
Loading...
+ 5 hidden pages