Kenwood DVR-7000, DVR-505 User Manual
DVD RECEIVER
DVR-505
DVR-7000
INSTRUCTION MANUAL
KENWOOD CORPORATION
B60-5149-08 00 (K/P/T/M/X/Y) OC 01/07
COMPACT
DIGITAL VIDEO
2
Introduction
DVR-505/DVR-7000 (EN)
Before applying power
Units are designed for operation as follows.
U.S.A. and Canada ....................................................... AC 120V only
Australia ....................................................................... AC 240 V only
For the United Kingdom
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use
only a 3-Amp ASTA-approved (BS 1362) fuse.
2. The fuse cover must be refitted when replacing the
fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in
Preparations
your home or the cable is too short to reach.
A power point, then obtain an appropriate safety
approved extension lead or adapter, or consult your
dealer. If nonetheless the mains plug is cut off,
remove the fuse and dispose of the plug immediately,
to avoid a possible shock hazard by inadvertent.
Connection to the mains supply.
IMPORTANT :
The wires in the mains lead are coloured in accordance
with the following code:
Blue : Neutral
Brown : Live
Do not connect those leads to the earth terminal of a
three-pin plug.
Caution : Read this page carefully to ensure safe operation.
Europe and U.K. ............................................................ AC 230V only
*Other countries .................... AC 110-120 / 220-240 V switchable
*For other countries
AC voltage selection
This unit operates on 110-120 or 220-240 volts AC . The
AC voltage selector switch on the rear panel is set to the
voltage that prevails in the area to which the unit is
shipped. Before connecting the power cord to your AC
outlet, make sure that the setting position of this switch
matches your line voltage. If not, it must be set to your
voltage in accordance with the following direction.
AC voltage selector switch
Move switch lever to match your line voltage with
a small screwdriver or other pointed tool.
Note:
Our warranty does not cover damage caused by excessive
line voltage due to improper setting of the AC voltage
selector switch.
Safety precautions
Caution : Read this page carefully to ensure safe operation.
WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The marking this product has been classified as Class
1. It means that there is no danger of hazardous radiation outside the product.
Location: Back panel
Contents
3
DVR-505/DVR-7000 (EN)
Caution : Read the pages marked carefully to ensure safe operation.
Preparations
Introduction ...................................................................................... 2
Before applying power ..................................................... 2
Safety precautions............................................................. 2
Accessories ............................................................................... 4
CHANNEL SPACE setting (Except for the U.S.A., Canada, ..
U.K., Europe and Australia) ............................................... 4
IMPORTANT SAFEGUARDS .................................................... 5
Special features and Contents ..................................................... 7
Reference ......................................................................................... 7
Maintenance .................................................................................... 8
Discs information ............................................................................ 9
Types of playable discs ........................................................... 9
Unplayable discs ...................................................................... 9
Icons on the DVD discs ............................................................ 9
Region codes ................................................................................. 10
Region codes in the world .................................................... 10
Examples of TV screen display of each video format...... 10
Video formats ................................................................................. 11
Video formats of DVD discs that can be played on this unit....... 11
System Connections .............................................................. 12
Loudspeakers .......................................................................... 12
AM loop antenna .................................................................... 13
FM antenna .............................................................................. 13
Connecting to a TV ................................................................. 14
Connecting to a Satellite Tuner ........................................... 14
Connecting to Audio video equipments ............................. 15
Connecting a Camcorder or Video game machine........... 15
Controls and indicators................................................................ 16
Operation of remote control unit ................................................ 17
Operations
Let's put out some sound ............................................................. 18
Basic use method ................................................................... 18
Changing the Tone .................................................................. 19
Receiving broadcast station ....................................................... 21
Storing the broadcast stations (one-by-one presetting) ............
Using RDS function ( for U.K. only) ...................................... 23
Playback of disc ............................................................................ 25
Basic play ................................................................................ 25
Disc playback features .......................................................... 26
Using the On-screen banner display ......................................... 27
Selecting a Title ...................................................................... 28
Selecting a Chapter or Track ................................................ 28
Changing the Audio Language ............................................. 29
22
Changing the Subtitle Language.......................................... 29
Changing the Camera angle ................................................. 30
Using IntroScan function ...................................................... 30
Using Bookmarks ................................................................... 31
Repeat play .............................................................................. 32
A-B Repeat play ...................................................................... 32
Random play ............................................................................ 33
Program play .................................................................................. 34
Menu playback .............................................................................. 36
Hierarchical structure of VCD menus ................................. 36
Examples of operation keys and indications used during..
VCD playback .................................................................... 36
Playback without using the menu playback function
case of a P.B.C.-compatible VCD) (To P.B.C. On or Off) ......... 37
MP3 function .................................................................................. 38
Guidance of MP3 .................................................................... 38
MP3 On-screen display ......................................................... 39
Playing back MP3 ................................................................... 39
Selecting MP3 files or folders ............................................. 40
MP3 program playback ......................................................... 41
Set Up functions ............................................................................ 42
Set up menu ............................................................................. 42
Select Audio Language ......................................................... 43
Select Subtitle Language ...................................................... 43
Select Menu Language .......................................................... 44
Select Rating ........................................................................... 44
Password ................................................................................. 45
TV aspect .................................................................................. 47
Setting up LISTEN mode .............................................................. 48
What are LISTEN modes? ...................................................... 48
To set the LISTEN mode manually ....................................... 49
Speaker setting ............................................................................. 50
Changing the INPUT MODE ......................................................... 52
Control of a different device with the accessory remote controller .... 53
Register the setup codes for your audio and video.......... 53
Operating other devises ........................................................ 53
Setup code table (for U.K.) .................................................... 54
Setup code table (for U.S.A., Canada and other countries)
............................................................................................. 57
Keys which can be used to operate connected devices 60
(In .....
Knowledge
Knowledge ..................................................................................... 61
DVD menu language code list .............................................. 61
In case of difficulty ....................................................................... 62
Specifications................................................................................ 65
Preparations
4
DVR-505/DVR-7000 (EN)
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit
was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can
file a claim against the carrier for shipping damage.
We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.
Keep this manual handy for future reference.
Accessories
Please confirm that the following accessories are present.
Accessories packed with the main unit
FM indoor antenna (1) Loop antenna (1)
Video cord (1)
Preparations
Remote control unit (1) Batteries (LR03/AAA) (2)
Speaker cords (6)
*AC plug adaptor (1)
* Use to adapt the plug on the
power cord to the shape of
the wall outlet.
(Accessory only for regions
where use is necessary.)
SCART plug (1) (for U.K. only)
Speaker model names
System Front speakers and surround speakers Subwoofer
DVR-505 KS-305DV (Left speaker, right speaker, SW-15DV
center speaker and surround speakers)
DVR-7000 KSW-7000 (Left speaker, right speaker, center speaker, surround speakers and subwoofer)
CHANNEL SPACE setting
The space between radio channels has been set to the one
that prevails in the area to which the system is shipped.
However, if the current channel space setting does not
match the setting in the area where the system is to be used,
for instance when you move from area 1 or area 2 shown in
the following table or vice versa, proper reception of AM/FM
broadcasts cannot be expected. In this case, change the
channel space setting in accordance with your area by referring to the following table.
Area
USA, Canada and South
1
American countries
2
Other countries
CHANNEL
SPACE frequency
FM : 100 kHz
AM : 10 kHz
FM : 50 kHz
AM : 9 kHz
(Except for the U.S.A., Canada, U.K., Europe and Australia)
Setting the CHANNEL SPACE
1 Set the POWER key to standby (power off) mode.
2 press the STOP key, the ¢ key and the 4 key on
main unit in this order.
Each operate step 2, switches the modes as follows.
1 “FM100/AM10 kHz” STEP
2 “FM 50 /AM 9 kHz” STEP
IMPORTANT SAFEGUARDS
Caution : Read this page carefully to ensure
safe operation.
DVR-505/DVR-7000 (EN)
5
Please read all of the safety and operating instructions
before operating this appliance. Adhere to all warnings on
the appliance and in the instruction manual. Follow all the
safety and operating instructions. These safety and
operating instructions should be retained for future
reference.
1. Power sources – The appliance should be connected to
a power supply only of the type described in the instruction
manual or as marked on the appliance. If you are not sure
of the type of power supply to your home, consult your
appliance dealer or local power company. For appliances
intended to operate from battery power, or other sources,
refer to the instruction manual.
2. Power-cord protection – Power-supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
3. CAUTION – Polarization – This appliance may
be equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
4. Ventilation – Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the appliance and to protect it from overheating, and these
openings must not be blocked or covered. The appliance
should be situated so that its location or position does not
interfere with its proper ventilation.
To maintain good ventilation, do not put records or a tablecloth on the appliance. Place the appliance at least 10 cm
away from the walls.
Do not use the appliance on a bed, sofa, rug or similar
surface that may block the ventilation openings. This
appliance should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
6. Temperature – The appliance may not function
properly if used at extremely low, or freezing
temperatures. The ideal ambient temperature is
above +5°C (41°F).
7. Heat – The appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce
heat.
8. Electric shock – Care should be taken so that objects
do not fall and liquid is not spilled into the enclosure
through openings. If a metal objects, such as a hair
pin or a needle, comes into contact with the inside of
this appliance, a dangerous electric shock may result.
For families with children, never permit children to
put anything, especially metal, inside this appliance.
9. Enclosure removal – Never remove the enclosure.
If the internal parts are touched accidentally, a serious
electric shock might occur.
10.Magnetic fields – Keep the appliance away from
sources of magnetic fields such as TV sets, speaker
systems, radios, motorized toys or magnetized
objects.
11.Cleaning – Unplug this appliance from the wall
outlet before cleaning. Do not use volatile solvents
such as alcohol, paint thinner, gasoline, or benzine,
etc. to clean the cabinet. Use a clean dry cloth.
12.Accessories – Do not place this appliance on an unstable
cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer,
or sold with the appliance. Any mounting of the appliance
should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer. An appliance and cart combination should
be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
Preparations
5. Water and moisture – The appliance should not be
used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
6
IMPORTANT SAFEGUARDS
DVR-505/DVR-7000 (EN)
13.Lightning – For added protection for this appliance during
a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the appliance due to lightning and power-line
surges.
14.Abnormal smell – If an abnormal smell or smoke is
detected, immediately turn the power OFF and unplug
the appliance from the wall outlet. Contact your dealer or
nearest service center.
POWER OFF!
15.Damage requiring service – The appliance should
be serviced by qualified service personnel when:
Preparations
A. The power-supply cord or the plug has been
damaged.
B. Objects have fallen, or liquid has been spilled into
the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally
by following the instruction manual. Adjust only those
controls that are covered by the instruction manual as an
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified
technician to restore the appliance to its normal operation.
E. The appliance has been dropped, or the enclosure
damaged.
F. The appliance exhibits a marked change in performance.
16.Servicing – The user should not attempt to service
the appliance beyond that described in the instruction
manual. All other servicing should be referred to
qualified service personnel.
17.Outdoor antenna grounding – If an outside antenna
is connected to the appliance, be sure the antenna
system is grounded so as to provide some protection
against voltage surges and built up static charges.
Article 810 of the National Electrical Code ANSI/
NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See
Figure.
18.Power lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
19.AC outlets – Do not connect other audio equipment
with a power consumption larger than that specified
to the AC outlet on the rear panel. Never connect
other electrical appliances, such as an iron or toaster,
to it to prevent fire or electric shock.
20. Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
21. Attachment – Do not use attachments not recommended
by the appliance manufacturer as they may cause hazards.
22. Replacement parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original parts. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
23. Safety check – Upon completion of any service or repairs
to this appliance, ask the service technician to perform
safety checks to determine that the appliance is in proper
operating condition.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
ELECTRICAL CODE
GROUND
CLAMPS
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
Notes:
1. Item 3 is not required except for grounded or polarized equipment.
2. Item 17 and 18 are not required except for units provided with
antenna terminals.
3. Item 17 complies with UL in the U.S.A.
Special features and Contents
Special features
This document classifies the applications of each feature using the following marks
: Description of a feature that can be used with DVD.
DVD
: Description of a feature that can be used with CD.
CD
: Description of a feature that can be used with VCD.
VCD
7
DVR-505/DVR-7000 (EN)
DVD
DVD
CD VCD
DVD
CD VCD
DVD
DVD
DVD
Higher video quality than S-VHS video and LaserDisc
Higher audio quality than music CD
Graphical user interface (GUI) compatibility
Versatile DVD playback features
CD
The DVR-505/DVR-7000 offers DTS decoder.
Dolby Pro Logic II decoder.
Reference
Caution on condensation
Condensation (of dew) may occur inside the unit when there is
a great difference in temperature between this unit and the
outside.
This unit may not function properly if condensation occurs. In
this case, leave the unit for a few hours with the power left ON,
and restart the operation after the condensation has dried up.
Be specially cautious against condensation in a following circumstance:
When this unit is carried from a place to another across a large
difference in temperature, when the humidity in the room where
this unit is installed increases, etc.
Note related to transportation and movement
Before transporting or moving this unit, carry out the
following operations.
1 Remove the disc from the unit.
2 Press the 6 key.
3 Wait a few seconds and turn the unit OFF.
Memory backup function
Stored contents which are
cleared in at least a week after power plug is unplugged
from power outlet.
Amplifier section
Last input selection
Volume control value
Surround setting
CINEMA EQUALIZER
B. BOOST
Tuner section
Receiving band
Frequency
Preset stations
Tuning mode setting
DVD section
Menu setup
Power status
WARNING NOTICE:
IN MOST CASES IT IS AN INFRINGEMENT OF COPYRIGHT TO MAKE COPIES OF TAPES OR DISCS WITHOUT THE PERMISSION OF THE COPYRIGHT OWNERS.
ANYONE WISHING TO COPY COMMERCIALLY AVAILABLE TAPES OR DISC SHOULD CONTACT THE MECHANICAL COPYRIGHT PROTECTION SOCIETY LIMITED OR THE PERFORMING RIGHTS SOCIETY LIMITED.
Preparations
8
Maintenance
DVR-505/DVR-7000 (EN)
Maintenance of the Set
When the front panel, the case, etc. becomes dirty, wipe with a
soft, dry cloth. Do not use thinner, alcohol, etc., as these can
cause discoloration.
Disc handling precautions
Handling
Hold the discs so that you do not touch
the playing surface.
Label side
Playing side
Sticker
Do not attach paper or tape to either
Preparations
Sticky paste
the playing side or the label side of the
discs.
In regard to contact cleaners
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
Cleaning
If fingerprints or foreign matter become attached
to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc
outwards in a radial manner.
Storage
When a disc is not to be played for a long period
of time, remove it from the player and store it in
its case.
Never play a cracked or warped disc
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed disc
or a disc repaired with tape or adhesive agent.
Please do not use discs which are not round because they may
cause a malfunction.
Disc accessories
The disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound quality or
protecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction.
For the U.S.A.
CAUTION:
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of
labels on, or inside the product relating to laser product safety.
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI,
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO
DHHS REGULATIONS NO. 21 CFR
1040.10, CHAPTER 1, SUBCHAPTER J.
Location: Back Panel
CAUTION- LASER RADIATION WHEN OPEN.
Location: Laser Pick-up Unit Cover inside this product
DO NOT STARE INTO BEAM.
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio
communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio / TV technician for help.
Discs information
DIGITAL VIDEO
COMPACT
DVR-505/DVR-7000 (EN)
Types of playable discs
The system using this unit does not only play music from CD but can also play the discs listed below to offer you
high-quality entertainment of video of movies and live concerts.
9
Playable Disc
Logo mark on disc
Disc size
Played sides
Contents
Video + Audio
Audio
DVD CD
8cm
One or both One or both
Approx. 41 min.
(1 side, 1 layer)
Approx. 75 min.
(1 side, 2 layers)
Approx. 82 min.
(2 sides, 1 layer)
Approx. 150 min.
(2 sides, 2 layers)
Approx. 133 min.
(1 side, 1 layer)
Approx. 242 min.
(1 side, 2 layers)
Approx. 266 min.
(2 sides, 1 layer)
Approx. 484 min.
(2 sides, 2 layers)
12cm
8cm
One side only One side only
Max. 20 min., digital Max. 74 min., digital
12cm
VCD
COMPACT
DIGITAL VIDEO
Preparations
12cm
One side only
Max. 74 min.
Unplayable discs
This player cannot play back any of the following discs.
÷ DVD-ROM discs
÷ DVD-R/DVD-RAM/DVD-RW discs
÷ VSD discs
÷ CDV discs (only the audio part can be reproduced.)
÷ CD-ROM discs (except MP3 (ISO 9660 level 1 format) disc.)
Icons on the DVD discs
Icon Description
ALL
8
32
9
Indicates the region code where the disc can be played.
Number of voice languages recorded with the audio function. The number in the icon indicates the number of voice languages.
(Max. 8 languages)
Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the number of subtitle
languages. (Max. 32 languages)
Number of angles provided by the angle function. The number in the icon indicates the number of angles. (Max. 9 angles)
÷ CD-G/CD-EG/CD-EXTRA discs (only the audio can be
reproduced.)
÷ Photo CD discs (never attempt to play them.)
÷ S-VCD discs
16:9 LB
Aspect ratios that can be selected. “LB” stands for Letter Box and “PS” for Pan/Scan. In the example on the left, the 16:9 video
can be converted into letter box video.
10
Region codes
DVR-505/DVR-7000 (EN)
Every player of this model has a certain region code assigned to it based on the country where the player is used.
When the player is used to play back DVD discs, it can only play the DVD discs carrying the region codes matching
the region code of the player.
The region code for this player is described on the rear panel of the player.
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the following
map.
Preparations
1
5
2
1
6
2
3
4
1
5
2
4
Examples of TV screen display of each video format
When your TV is switchable between PAL/
NTSC
Try play a disc. If the picture is black and white or as shown on the right,
stop playback and switch the screen display formats of this unit and the
TV to another format. This will improve the played picture quality.
When your TV is compatible only with the
PAL format
With certain discs, the playback picture may have black spaces above
and below it (as shown on the right).
This is because the disc has been
recorded in the NTSC format. The
screen may be somewhat hard to
see but this is not malfunction.
When your TV is compatible only with the
NTSC format
With certain discs, the playback picture may be cut above and below it
(as shown on the right). This is because the disc has been recorded in
the PAL format. The screen may be
somewhat hard to see but this is not
malfunction.
Video formats
11
DVR-505/DVR-7000 (EN)
The video signals used to display TV pictures and video
TV formats of major countries
disc pictures are mainly based on two types of signal
formats (PAL and NTSC), which are assigned to each
country or area as shown on the right. As a result, it is
required to select discs according to the video format
used with your TV monitor (in your country or area).
TV Format
NTSC
PAL
Japan, Taiwan, Korea, U.S.A., Canada, Mexico,
Philippines, Chile, etc.
China, U.K., Germany, Australia, New Zealand,
Kuwait, Singapore, etc.
Major Countries & Areas
Video formats of DVD discs that can be played on this unit
Region code table
District 1
Area or
Country
Name,
Region
Code
North
America
1 2 2 2 3 4 4 5 6
Set the video formats of the DVD discs to be played on this unit as described below.
District 2-1
Europe
District 2-2
Japan
District 2-3
Middle East
District 3
Southeast
Asia
District 4-1
Oceania
District 4-2
South
America
District 5
Russia
Preparations
District 6
China
Check the video format(s) used by your TV monitor.
1
÷ Refer to the operating instructions of your TV monitor for details.
Select DVD discs recorded with the playable video format by referring to the following table.
2
÷ See the region code table on this page for details on districts 1 to 6.
Your TV
format
NTSC only
PAL only
NTSC/PAL
switchable
Note
Note
When your TV is switchable between NTSC and PAL,
3
÷ Districts 1, 2-2 and 4-2: Set the TV to NTSC.
÷ Districts 2-1, 4-1 and 5: Set the TV to PAL.
÷ Districts 2-3, 3 and 6 : Set the TV according to each disc to be played.
District 1
NTSC
NTSC*
NTSC
Normal video may not be reproduced when a disc recorded with the video format marked * in the above table is played. See “Examples of TV
screen display of each video format” for details. 0
District 2-1
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 2-2
NTSC
NTSC*
NTSC
District 2-3
Playable Disc Formats
District 3
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
NTSC*
NTSC
PAL*
PAL
NTSC
PAL
District 4-1
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 4-2
NTSC
NTSC*
NTSC
District 5
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 6
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
Restrictions due to difference between discs
Some DVD discs can be played only in certain playback modes according to the intentions of the software
producers. As this player plays discs according to their intentions, some functions may not work as
intended by you. Please be sure to read the instructions provided with each disc. When an inhibition icon
is displayed on the TV screen connected to the player, it indicates that the disc being played is under the
restriction as described above.
Inhibition icon
12
System Connections
Make connections as shown below.
When connecting the related system components, refer also
to the instruction manuals of the related components.
Caution : Read this page carefully to ensure
safe operation.
DVR-505/DVR-7000 (EN)
Caution:
Do not plug in the power lead until all connections are completed.
Caution
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or
fire hazard.
÷ Do not place any objects impairing heat radiation onto the top of unit.
÷ Leave a space around the unit (from the largest outside dimension including pro-
jection) equal or greater than, shown below.
Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm
Loudspeakers
Speaker terminal
12
Preparations
Excessive insertion of the cable can
Note
Note
cause defective contact.
The figure shows an example for the speakers for DVR-505.
Front
speaker
R
Center speaker
Color tube
Malfunction of microcomputer
If operation is not possible or erroneous
display appears even though all connections have been made properly, reset the
microcomputer referring to “In case of
difficulty”. „
Black tube
–
Front
speaker
L
+
White
tube
Upper side mark
Surround
speaker
R
Subwoofer
Speakers for DVR-7000
Connect the speaker cable terminals
to the terminals with the same color
at the speaker terminal panel on the
main unit. Connect matching the
color of the speaker terminal (+ side)
and the color of the speaker cable
tube.
Speaker
Front right
Center
Front left
Surround right
Subwoofer
Surround left
Surround
speaker
L
Color of the speaker terminal
panel on the main unit
Red
Green
Blue
Orange
Brown
Gray
Caution : Read this page carefully to ensure safe operation.
AM loop antenna
AM loop antenna connection
The supplied antenna is
for indoor use. Place it as
far as possible from the
main system, TV set,
speaker cords and power
cord, and set it to a direction which provides the
best reception.
White
System Connections
DVR-505/DVR-7000 (EN)
13
Preparations
FM antenna
FM indoor antenna connection
The accessory antenna is for
temporary indoor use only.
For stable signal reception
we recommend using an outdoor antenna. Remove the
indoor antenna if you connect one outdoors.
FM outdoor antenna
(commercially available)
Lead the 75 Ω coaxial
cable connected to the
FM outdoor antenna
into the room and con-
nect it to the FM 75 Ω
terminal.
1 Connect to the antenna terminal.
2 Locate the position providing good
reception condition.
3 Fix the antenna.
FM 75Ω
FM 75Ω
14
Connecting to a TV
TV
Preparations
System Connections
DVR-505/DVR-7000 (EN)
Depending on the input switching, the output from the MONITOR OUT terminal will be one of
the following signals. Please note that a different signal type will not be put out.
S-VIDEO terminal : S-video signal connected to the (S-VIDEO) VCR IN, the (S-VIDEO) SAT IN, or
the AV AUX S terminal.
VIDEO terminal : Composite video signal connected to the (VIDEO) VCR IN, the (VIDEO) SAT
IN, or the AV AUX VIDEO terminal.
COMPONENT Video cord (except for U.K)
*COMPOSITE Video cord (accessory)
S-Video cord
COMPONENT connection corresponds only to some areas.
Note
When the TV has a COMPONENT terminal, the DVD image will be played
Note
back with higher picture quality in case of COMPONENT connection.
Connect the S-video or the COMPOSITE video cable also in this case.
Connecting to a Satellite Tuner
Remove protective cap
before connecting.
* For U.K. only
If your TV set has a SCART terminal,
connect the accessory SCART plug to the
SCART terminal of the TV and connect
the COMPOSITE video cord.
Satellite tuner
OPTICAL or COAXIAL cable
S-video cord
COMPOSITE
video cord
Audio cord
Connect the OPTICAL or the COAXIAL cable, depending on the digital output of the satellite tuner.
Connecting to Audio video equipments
In case of digital recording
with an MD recorder or a CD
recorder
OPTICAL cable
DIGITAL OUT signal is PCM format
System Connections
DVR-505/DVR-7000 (EN)
15
Preparations
COMPOSITE video cord
S-video cord
S-video cord
COMPOSITE video cord
Note
Note
Analog recording of DTS-encoded
discs is not possible.
Audio cords
Connecting a Camcorder or Video game machine
Video game machine
OPTICAL cable
Camcorder
S VIDEO
DIGITAL
(OPTICAL)
Audio cord
COMPOSITE video cord
S-video cord
16
Controls and indicators
INTRO SCAN indicator
RANDOM indicator
PARENTAL LOCK
indicator
PLAY/PAUSE indicator
RDS indicator (only
for U.K.)
PBC indicator
PROG. (Program)
indicator
TITLE indicator
TRACK indicator
CHAPTER indicator
DVR-505/DVR-7000 (EN)
AUTO indicator
TUNED indicator
ST (Stereo) indicator
CINEMA EQ
mode indicator
B. BOOST indicator
Preparations
1
2
DVD indicator
VCD indicator
CD indicator
MP3 indicator
REPEAT indicators
REPEAT
A-B REPEAT
34 567
Display
IN/OUT status indicator
Character
information
display section
L : Left speaker
C : Center speaker
R : Right speaker
LFE : Low Frequency Effect
SW : Subwoofer
LS : Left surround speaker
S : Surround speakers
RS : Right surround speaker
()¡
S VIDEO
89 0 ! @# $
DIGITAL
(OPTICAL)
*
&
^
%
1 STANDBY indicator ^
2 POWER switch *
LISTEN MODE indicators
3 DTS indicator o
4 DOLBY DIGITAL indicator o
5 PRO LOGIC indicator o
6 DSP indicator o
7 CS-5.1 indicator o
8 BAND key ¡
44
9
0 AV AUX S VIDEO jack %
¢¢
4,
¢ (Skip) keys ¡
44
¢¢
! AV AUX VIDEO jack %
@ AV AUX AUDIO jacks %
# AV AUX OPTICAL input jack %
$ PHONES jack *
% Door *
66
^
6 (PLAY/PAUSE) key ∞
66
77
&
7 (STOP) key ∞
77
* INPUT key *
( VOLUME CONTROL knob *
00
)
0 (EJECT) key ∞
00
¡ Disc tray ∞
STANDBY indicator
The STANDBY indicator lights when the power cable is plugged into an outlet and the POWER switch is set to ON. When the
POWER key on the remote control unit is pressed in STANDBY status, the STANDBY indicator goes out and the main unit reaches
operation status. When the POWER switch is set to OFF in operation status, the unit will return to operation status when the
POWER switch is set to ON again. When the POWER switch is set to OFF in STANDBY status, the unit will return to STANDBY
status when the POWER switch is set to ON again.
Operation of remote control unit
1
2
3
4
5
6
7
8
9
0
!
@
MUTE
DVD CD
AV AUX
123
456
7809
+10 +100
CLEAR
FCRSW
+
REPEAT
A-B
–
M
E
N
P
U
O
T
GUIDE
U
R
T
N
E
R
S.TITLE
POWER
INPUT SELECTOR
RADIO VCR SAT
BAND
TV
CABLE
P.MODE
TRIM
M
.
T
U
N
L
T
O
I
C
ENTER
EXIT
AUTO/MONO
DEVICE
TV INPUT
LSTN MODE
SOUND
SETUP
INPUT MODE
RANDOM
VOLUMECH.
E
M
PTY
R
C
S
N
O
RDS
SELECT
#
TUNE / TV. VOLUME P.CALL / THUM / PAGE
$
JUMP
SLOW STEP
Model : RC-R0722 (for U.K.)
RC-R0721 (for other countries)
Infrared ray system
B.BOOST
CINE.EQ
%
^
&
*
(
)
¡
N
U
™
E
E
N
£
¢
The keys on the remote control unit with the same names as on the
main unit have the same function as the keys on the main unit.
1 LED indicator E
2 MUTE key *
3 INPUT SELECTOR keys *
DVD CD key
RADIO/BAND key
VCR key
SAT (Satellite) key
AV AUX key
4 Device keys E
TV key
CABLE key
5 Numeric keys (0 - 9, +10,+100)
CLEAR key ¶
P.MODE key ›
6 Speaker select keys W
F (Front) key
C (Center) key
R (Rear/Surround) key
SW (Subwoofer) key
7 CH.(Channel) + key P
/REPEAT key ¤
8 CH.(Channel) – key P
/A-B Repeat key ¤
9 TRIM / MULTI CONT.
55
Up (
5), Down (
55
0 TOP MENU key ‡
/GUIDE key P
! Cursor Up (
and Right (
ENTER key •
@ RETURN key w
/ EXIT key P
∞∞
∞) keys Q
∞∞
55
5), Down (
55
33
3) keys ›
33
§P
∞∞
∞), Left (
∞∞
22
2)
22
DVR-505/DVR-7000 (EN)
# ● (record) /S.TITLE (SUB TITLE)
key ª
7 7
7 (stop) / AUTO/MONO key
7 7
¡∞
8 (pause) key ∞
3 (play) key ∞
1 1
$
¡ ¡
1 /
¡ key (Search keys)
1 1
¡ ¡
TUNE/ keys §
/TV. VOLUME keys P
4 4
4 key/
4 4
¢ ¢
¢ key (Skip keys)
¢ ¢
P.CALL keys §
/THUM/PAGE keys P
% POWER key &
^ DEVICE Power key P
& TV INPUT key P
* LSTN MODE (LISTEN MODE)
key )o
(
SOUND / SETUP key
(p
) INPUT MODE / RANDOM key
‹
¡ VOLUME keys *
™ PTY (for U.K. only) / MENU key
¢w
™ RDS (for U.K. only) / ON SCREEN
key £¶
¢ SLOW / JUMP key §
STEP key §
B.BOOST key (
CINE.EQ key )
* Depending on the area, the
AUTO/MONO key is marked as
MONO.
17
Preparations
Loading batteries
2 Insert batteries. 3 Close the cover.1 Remove the cover.
÷ Insert two LR03 (“AAA”-size) batteries
following the polarity indications.
Operation
Insert the power plug into a power outlet, press the POWER
switch of the main unit to ON, then press the POWER key
on the remote control.
÷ When pressing more than one remote control keys successively,
press the keys securely by leaving an interval of 1 second or more
between pressing of keys.
1. The provided batteries are intended for use in operation checking, and their service life may be short.
Notes
Notes
2. When the remote controllable distance becomes short, replace both of the batteries with new ones.
3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction
may occur. In such a case, change the installation position to avoid malfunction.
Remote sensor
6m
Operating range (approx.)
30º
30º
18
Note
Note
Let's put out some sound
Preparation
÷ set the POWER ON/OFF switch to the ON ( )
position.
Basic use method
Selecting the desired input
1
MAIN UNIT
Switching is done as follows when the INPUT key of the
main unit is pressed.
1 Tuner (frequency display)
2 VCR (VCR/ANL)
3 SAT (SAT/ANL, SAT/COAX or SAT/OPTI)
4 AV AUX (AUX/ANL or AUX/OPTI)
5 DVD/CD
Operations
Volume adjustment
2
MAIN UNIT
REMOTE
DVD CD
AV AUX
REMOTE
VOLUME
INPUT SELECTOR
RADIO VCR SAT
BAND
To increase
DVR-505/DVR-7000 (EN)
MUTE
key
INPUT
SELECTOR
keys
÷ When one of the keys on the left is pressed while STANDBY
mode, the power will be switched on automatically and the input
will be selected.
÷ The power will be switched on and the respective operation will
be performed also when the EJECT key, the PLAY/PAUSE key
or the BAND key on the main unit is pressed during STANDBY
mode.
÷ When a disc is set in the disc tray and the DVD CD key is pressed,
disc playback will start automatically.
In case of operation with the remote control unit, first select
the input or device to be operated wit the INPUT SELECTOR
keys etc., and then perform the desired operation.
The present mode of the remote control unit may not
coincide with the equipment to be operated.
The input mode can be switched with SAT and AV
AUX. Refer to “Changing the INPUT MODE” W
Normally "MAX" is displayed when the volume settings set to
the maximum value.
Depending on the speaker setting value or when CINE.EQ has
been set to "ON", ()), "MAX" will not be displayed.
POWER
key
VOLUME
keys
POWER switch
VOLUME CONTROL knob
INPUT key
PHONES jack
To decrease To increase
To decrease
Muting the sound temporarily
Remote control unit only
MUTE
Listening through headphone
Insert the headphone plug into the PHONES jack.
÷ Press MUTE key.
÷ Press again to resume the original volume.
÷ The sound muting is also cancelled when the volume is con-
trolled.
This unit offers various surround modes, but it switches
automatically to stereo mode when headphones are connected.
To open the door, pull the lower part on the right side of the
main unit.
÷ The sounds from all speakers are cut off.
Let's put out some sound
DVR-505/DVR-7000 (EN)
Changing the Tone
This unit is equipped with various preset equalizers, so that various sounds can be enjoyed. In addition, it has an B.BOOST
function for one-touch bass correction.
B.BOOST
When the B.BOOST function is switched on, richer bass
tones can be reproduced.
19
REMOTE
Press the B.BOOST key
B.BOOST
Each press switches the B.BOOST on or off.
1 B.BOOST lit
2 B.BOOST goes off
TREBLE CONTROL (Normal music CD , VCD and tuner only)
REMOTE
Press the LSTN MODE key
Set to STEREO mode. (The TREBLE CONTROL can be
adjusted only STEREO mode)
1
LSTN MODE
Operations
Press the SOUND key
2
Select treble level
3
SOUND
SETUP
TRIM
M
U
N
L
T
O
I
C
To increase
.
T
To decrease
TRBL is displayed.
Operation is not possible with DOLBY DIGITAL and DTS
source.
Each press switch the TRBL level
÷ The treble level can be adjusted between +10 and -10.
20
Selecting the DSP mode
Five different sounds are preset in DSP mode. Please select the type you like.
DSP mode can be selected only at the time of a PCM source (normal music CD, MP3 file, etc.).
Let's put out some sound
DVR-505/DVR-7000 (EN)
REMOTE
Press the LSTN MODE key repeatedly
LSTN MODE
Selecting the CINE.EQ (CINEMA EQUALIZER).
This function provides for better playback of movies etc.
REMOTE
Press the CINE.EQ key
CINE.EQ
Each press switches the mode
(At the time of music CD)
1 DOLBY PL II MOVIE
2 DOLBY PL II MUSIC
3 DOLBY PRO LOGIC
4 CIRCLE SURROUND
5 ARENA
6 JAZZ CLUB
7 THEATER
8 STADIUM
9 DISCO
0 STEREO
Each press switches the mode
1 CINE.EQ
2 OFF
DSP modes
Lit
DSP
Operations
Selecting the NIGHT (MID NIGHT) mode. (Dolby Digital only)
Any time you don’t want to experience the loud and soft volume extremes of recorded sound (for example, late at night), use
NIGHT function to reduce volume extremes.
REMOTE
Press the SOUND key.
1
Press the TRIM (5/∞) key.
2
SOUND
SETUP
Displayed NIGHT OFF or NIGHT ON.
Each press switches the mode
1 NIGHT ON
2 NIGHT OFF
TRIM
M
U
L
.
T
N
T
O
I
C
Receiving broadcast station
It is also possible to receive them by one-touch operations
by storing up to 30 stations in the preset memory. (see page
22)
RADIO/BAND
key
21
DVR-505/DVR-7000 (EN)
Select the TUNER input
1
MAIN UNIT
Select the broadcast band
2
MAIN UNIT
REMOTE
RADIO
BAND
REMOTE
RADIO
BAND
AUTO/MONO
key
1, ¡ keys
When the BAND key is pressed, this unit will be
switched on automatically.
Each press changes the band.
1 FM
2 AM
4, ¢
keys
Auto tuning
mode indication
Preset number
Band display
Tuning indication
BAND key
4, ¢ keys
Stereo tuning indication
Frequency display
Operations
Select a tuning mode
3
REMOTE
AUTO/MONO
Each press switches the mode
1 auto tuning mode
Lit
2 manual tuning mode
When the TUNE keys are pressed in AUTO mode, a station will
be tuned in automatically and tuning will stop. Stereo reception
will be made automatically when a stereo broadcast with sufficient signal strength is received.
Select a station
4
P.CALL (preset call) AUTO (auto tuning) MANUAL (manual tuning)
REMOTEMAIN UNIT REMOTE
P.CALL / THUM / PAGE
Press the 4 , ¢ keys to select a
preset station.
TUNE / TV VOLUME
Press the TUNE key to receive the
next tuned station automatically
REMOTE
Each time a key is pressed, the frequency
is changed by one step.
When a key is pressed continuously, the
frequency changes continuously.
Use the manual tuning mode when reception is noisy due to weak reception.
(In the manual mode, stereo broadcasts
are received in monaural.)
TUNE / TV VOLUME
Loading...